| Stefan Roese | b47a63d | 2015-10-02 08:20:35 +0200 | [diff] [blame] | 1 | /* |
| 2 | * (C) Copyright 2007 |
| 3 | * Stefan Roese, DENX Software Engineering, sr@denx.de. |
| 4 | * |
| 5 | * Copyright (C) 2002 Scott McNutt <smcnutt@artesyncp.com> |
| 6 | * |
| 7 | * SPDX-License-Identifier: GPL-2.0+ |
| 8 | */ |
| 9 | |
| 10 | #include <asm-offsets.h> |
| 11 | #include <ppc_asm.tmpl> |
| 12 | #include <config.h> |
| 13 | #include <asm/mmu.h> |
| 14 | |
| 15 | /************************************************************************** |
| 16 | * TLB TABLE |
| 17 | * |
| 18 | * This table is used by the cpu boot code to setup the initial tlb |
| 19 | * entries. Rather than make broad assumptions in the cpu source tree, |
| 20 | * this table lets each board set things up however they like. |
| 21 | * |
| 22 | * Pointer to the table is returned in r1 |
| 23 | * |
| 24 | *************************************************************************/ |
| 25 | .section .bootpg,"ax" |
| 26 | .globl tlbtab |
| 27 | |
| 28 | tlbtab: |
| 29 | tlbtab_start |
| 30 | |
| 31 | /* |
| 32 | * BOOT_CS (FLASH) must be first. Before relocation SA_I can be off to use the |
| 33 | * speed up boot process. It is patched after relocation to enable SA_I |
| 34 | */ |
| 35 | tlbentry(CONFIG_SYS_BOOT_BASE_ADDR, SZ_256M, CONFIG_SYS_BOOT_BASE_ADDR, 1, AC_RWX | SA_G) |
| 36 | |
| 37 | /* |
| 38 | * TLB entries for SDRAM are not needed on this platform. |
| 39 | * They are dynamically generated in the SPD DDR(2) detection |
| 40 | * routine. |
| 41 | */ |
| 42 | |
| 43 | #ifdef CONFIG_SYS_INIT_RAM_DCACHE |
| 44 | /* TLB-entry for init-ram in dcache (SA_I must be turned off!) */ |
| 45 | tlbentry(CONFIG_SYS_INIT_RAM_ADDR, SZ_4K, CONFIG_SYS_INIT_RAM_ADDR, 0, AC_RWX | SA_G) |
| 46 | #endif |
| 47 | |
| 48 | /* TLB-entry for PCI Memory */ |
| 49 | tlbentry(CONFIG_SYS_PCI_MEMBASE, SZ_256M, CONFIG_SYS_PCI_MEMBASE, 1, AC_RW | SA_IG) |
| 50 | tlbentry(CONFIG_SYS_PCI_MEMBASE1, SZ_256M, CONFIG_SYS_PCI_MEMBASE1, 1, AC_RW | SA_IG) |
| 51 | tlbentry(CONFIG_SYS_PCI_MEMBASE2, SZ_256M, CONFIG_SYS_PCI_MEMBASE2, 1, AC_RW | SA_IG) |
| 52 | tlbentry(CONFIG_SYS_PCI_MEMBASE3, SZ_256M, CONFIG_SYS_PCI_MEMBASE3, 1, AC_RW | SA_IG) |
| 53 | |
| 54 | /* TLB-entry for the FPGA Chip select 2 */ |
| 55 | tlbentry(CONFIG_SYS_FPGA_BASE_0, SZ_1M, CONFIG_SYS_FPGA_BASE_0, 1, AC_RWX | SA_I|SA_G) |
| 56 | |
| 57 | /* TLB-entry for the FPGA Chip select 3 */ |
| 58 | tlbentry(CONFIG_SYS_FPGA_BASE_1, SZ_1M, CONFIG_SYS_FPGA_BASE_1, 1,AC_RWX | SA_I|SA_G) |
| 59 | |
| 60 | /* TLB-entry for the LIME Controller */ |
| 61 | tlbentry(CONFIG_SYS_LIME_BASE_0, SZ_16M, CONFIG_SYS_LIME_BASE_0, 1, AC_RWX | SA_I|SA_G) |
| 62 | tlbentry(CONFIG_SYS_LIME_BASE_1, SZ_16M, CONFIG_SYS_LIME_BASE_1, 1, AC_RWX | SA_I|SA_G) |
| 63 | tlbentry(CONFIG_SYS_LIME_BASE_2, SZ_16M, CONFIG_SYS_LIME_BASE_2, 1, AC_RWX | SA_I|SA_G) |
| 64 | tlbentry(CONFIG_SYS_LIME_BASE_3, SZ_16M, CONFIG_SYS_LIME_BASE_3, 1, AC_RWX | SA_I|SA_G) |
| 65 | |
| 66 | /* TLB-entry for Internal Registers & OCM */ |
| 67 | tlbentry(0xe0000000, SZ_16M, 0xe0000000, 0, AC_RWX | SA_I) |
| 68 | |
| 69 | /*TLB-entry PCI registers*/ |
| 70 | tlbentry(0xEEC00000, SZ_1K, 0xEEC00000, 1, AC_RWX | SA_IG) |
| 71 | |
| 72 | /* TLB-entry for peripherals */ |
| 73 | tlbentry(0xEF000000, SZ_16M, 0xEF000000, 1, AC_RWX | SA_IG) |
| 74 | |
| 75 | tlbtab_end |