Frieder Schrempf | 199dfd9 | 2021-09-29 16:42:42 +0200 | [diff] [blame] | 1 | // SPDX-License-Identifier: GPL-2.0+ OR MIT |
| 2 | /* |
| 3 | * Copyright (C) 2019 Kontron Electronics GmbH |
| 4 | */ |
| 5 | |
| 6 | #include "imx8mm.dtsi" |
| 7 | |
| 8 | / { |
| 9 | model = "Kontron i.MX8MM N801X SoM"; |
| 10 | compatible = "kontron,imx8mm-n801x-som", "fsl,imx8mm"; |
| 11 | |
| 12 | memory@40000000 { |
| 13 | device_type = "memory"; |
| 14 | /* |
| 15 | * There are multiple SoM flavors with different DDR sizes. |
| 16 | * The smallest is 1GB. For larger sizes the bootloader will |
| 17 | * update the reg property. |
| 18 | */ |
| 19 | reg = <0x0 0x40000000 0 0x80000000>; |
| 20 | }; |
| 21 | |
| 22 | chosen { |
| 23 | stdout-path = &uart3; |
| 24 | }; |
| 25 | }; |
| 26 | |
| 27 | &A53_0 { |
| 28 | cpu-supply = <®_vdd_arm>; |
| 29 | }; |
| 30 | |
| 31 | &A53_1 { |
| 32 | cpu-supply = <®_vdd_arm>; |
| 33 | }; |
| 34 | |
| 35 | &A53_2 { |
| 36 | cpu-supply = <®_vdd_arm>; |
| 37 | }; |
| 38 | |
| 39 | &A53_3 { |
| 40 | cpu-supply = <®_vdd_arm>; |
| 41 | }; |
| 42 | |
| 43 | &ddrc { |
| 44 | operating-points-v2 = <&ddrc_opp_table>; |
| 45 | |
| 46 | ddrc_opp_table: opp-table { |
| 47 | compatible = "operating-points-v2"; |
| 48 | |
| 49 | opp-25M { |
| 50 | opp-hz = /bits/ 64 <25000000>; |
| 51 | }; |
| 52 | |
| 53 | opp-100M { |
| 54 | opp-hz = /bits/ 64 <100000000>; |
| 55 | }; |
| 56 | |
| 57 | opp-750M { |
| 58 | opp-hz = /bits/ 64 <750000000>; |
| 59 | }; |
| 60 | }; |
| 61 | }; |
| 62 | |
| 63 | &ecspi1 { |
| 64 | pinctrl-names = "default"; |
| 65 | pinctrl-0 = <&pinctrl_ecspi1>; |
| 66 | cs-gpios = <&gpio5 9 GPIO_ACTIVE_HIGH>; |
| 67 | status = "okay"; |
| 68 | |
| 69 | spi-flash@0 { |
| 70 | compatible = "mxicy,mx25r1635f", "jedec,spi-nor"; |
| 71 | spi-max-frequency = <80000000>; |
| 72 | reg = <0>; |
| 73 | }; |
| 74 | }; |
| 75 | |
| 76 | &i2c1 { |
| 77 | clock-frequency = <400000>; |
| 78 | pinctrl-names = "default"; |
| 79 | pinctrl-0 = <&pinctrl_i2c1>; |
| 80 | status = "okay"; |
| 81 | |
| 82 | pca9450: pmic@25 { |
| 83 | compatible = "nxp,pca9450a"; |
| 84 | reg = <0x25>; |
| 85 | pinctrl-names = "default"; |
| 86 | pinctrl-0 = <&pinctrl_pmic>; |
| 87 | interrupt-parent = <&gpio1>; |
| 88 | interrupts = <0 IRQ_TYPE_LEVEL_LOW>; |
| 89 | sd-vsel-gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>; |
| 90 | |
| 91 | regulators { |
| 92 | reg_vdd_soc: BUCK1 { |
| 93 | regulator-name = "buck1"; |
| 94 | regulator-min-microvolt = <800000>; |
| 95 | regulator-max-microvolt = <850000>; |
| 96 | regulator-boot-on; |
| 97 | regulator-always-on; |
| 98 | regulator-ramp-delay = <3125>; |
| 99 | nxp,dvs-run-voltage = <850000>; |
| 100 | nxp,dvs-standby-voltage = <800000>; |
| 101 | }; |
| 102 | |
| 103 | reg_vdd_arm: BUCK2 { |
| 104 | regulator-name = "buck2"; |
| 105 | regulator-min-microvolt = <850000>; |
| 106 | regulator-max-microvolt = <950000>; |
| 107 | regulator-boot-on; |
| 108 | regulator-always-on; |
| 109 | regulator-ramp-delay = <3125>; |
| 110 | nxp,dvs-run-voltage = <950000>; |
| 111 | nxp,dvs-standby-voltage = <850000>; |
| 112 | }; |
| 113 | |
| 114 | reg_vdd_dram: BUCK3 { |
| 115 | regulator-name = "buck3"; |
| 116 | regulator-min-microvolt = <850000>; |
| 117 | regulator-max-microvolt = <950000>; |
| 118 | regulator-boot-on; |
| 119 | regulator-always-on; |
| 120 | }; |
| 121 | |
| 122 | reg_vdd_3v3: BUCK4 { |
| 123 | regulator-name = "buck4"; |
| 124 | regulator-min-microvolt = <3300000>; |
| 125 | regulator-max-microvolt = <3300000>; |
| 126 | regulator-boot-on; |
| 127 | regulator-always-on; |
| 128 | }; |
| 129 | |
| 130 | reg_vdd_1v8: BUCK5 { |
| 131 | regulator-name = "buck5"; |
| 132 | regulator-min-microvolt = <1800000>; |
| 133 | regulator-max-microvolt = <1800000>; |
| 134 | regulator-boot-on; |
| 135 | regulator-always-on; |
| 136 | }; |
| 137 | |
| 138 | reg_nvcc_dram: BUCK6 { |
| 139 | regulator-name = "buck6"; |
| 140 | regulator-min-microvolt = <1100000>; |
| 141 | regulator-max-microvolt = <1100000>; |
| 142 | regulator-boot-on; |
| 143 | regulator-always-on; |
| 144 | }; |
| 145 | |
| 146 | reg_nvcc_snvs: LDO1 { |
| 147 | regulator-name = "ldo1"; |
| 148 | regulator-min-microvolt = <1800000>; |
| 149 | regulator-max-microvolt = <1800000>; |
| 150 | regulator-boot-on; |
| 151 | regulator-always-on; |
| 152 | }; |
| 153 | |
| 154 | reg_vdd_snvs: LDO2 { |
| 155 | regulator-name = "ldo2"; |
| 156 | regulator-min-microvolt = <800000>; |
| 157 | regulator-max-microvolt = <800000>; |
| 158 | regulator-boot-on; |
| 159 | regulator-always-on; |
| 160 | }; |
| 161 | |
| 162 | reg_vdda: LDO3 { |
| 163 | regulator-name = "ldo3"; |
| 164 | regulator-min-microvolt = <1800000>; |
| 165 | regulator-max-microvolt = <1800000>; |
| 166 | regulator-boot-on; |
| 167 | regulator-always-on; |
| 168 | }; |
| 169 | |
| 170 | reg_vdd_phy: LDO4 { |
| 171 | regulator-name = "ldo4"; |
| 172 | regulator-min-microvolt = <900000>; |
| 173 | regulator-max-microvolt = <900000>; |
| 174 | regulator-boot-on; |
| 175 | regulator-always-on; |
| 176 | }; |
| 177 | |
| 178 | reg_nvcc_sd: LDO5 { |
| 179 | regulator-name = "ldo5"; |
| 180 | regulator-min-microvolt = <1800000>; |
| 181 | regulator-max-microvolt = <3300000>; |
| 182 | }; |
| 183 | }; |
| 184 | }; |
| 185 | }; |
| 186 | |
| 187 | &uart3 { /* console */ |
| 188 | pinctrl-names = "default"; |
| 189 | pinctrl-0 = <&pinctrl_uart3>; |
| 190 | status = "okay"; |
| 191 | }; |
| 192 | |
| 193 | &usdhc1 { |
| 194 | pinctrl-names = "default", "state_100mhz", "state_200mhz"; |
| 195 | pinctrl-0 = <&pinctrl_usdhc1>; |
| 196 | pinctrl-1 = <&pinctrl_usdhc1_100mhz>; |
| 197 | pinctrl-2 = <&pinctrl_usdhc1_200mhz>; |
| 198 | vmmc-supply = <®_vdd_3v3>; |
| 199 | vqmmc-supply = <®_vdd_1v8>; |
| 200 | bus-width = <8>; |
| 201 | non-removable; |
| 202 | status = "okay"; |
| 203 | }; |
| 204 | |
| 205 | &wdog1 { |
| 206 | pinctrl-names = "default"; |
| 207 | pinctrl-0 = <&pinctrl_wdog>; |
| 208 | fsl,ext-reset-output; |
| 209 | status = "okay"; |
| 210 | }; |
| 211 | |
| 212 | &iomuxc { |
| 213 | pinctrl_ecspi1: ecspi1grp { |
| 214 | fsl,pins = < |
| 215 | MX8MM_IOMUXC_ECSPI1_MISO_ECSPI1_MISO 0x82 |
| 216 | MX8MM_IOMUXC_ECSPI1_MOSI_ECSPI1_MOSI 0x82 |
| 217 | MX8MM_IOMUXC_ECSPI1_SCLK_ECSPI1_SCLK 0x82 |
| 218 | MX8MM_IOMUXC_ECSPI1_SS0_GPIO5_IO9 0x19 |
| 219 | >; |
| 220 | }; |
| 221 | |
| 222 | pinctrl_i2c1: i2c1grp { |
| 223 | fsl,pins = < |
| 224 | MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL 0x400001c3 |
| 225 | MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA 0x400001c3 |
| 226 | >; |
| 227 | }; |
| 228 | |
| 229 | pinctrl_pmic: pmicgrp { |
| 230 | fsl,pins = < |
| 231 | MX8MM_IOMUXC_GPIO1_IO00_GPIO1_IO0 0x141 |
| 232 | MX8MM_IOMUXC_GPIO1_IO04_GPIO1_IO4 0x141 |
| 233 | >; |
| 234 | }; |
| 235 | |
| 236 | pinctrl_uart3: uart3grp { |
| 237 | fsl,pins = < |
| 238 | MX8MM_IOMUXC_UART3_RXD_UART3_DCE_RX 0x140 |
| 239 | MX8MM_IOMUXC_UART3_TXD_UART3_DCE_TX 0x140 |
| 240 | >; |
| 241 | }; |
| 242 | |
| 243 | pinctrl_usdhc1: usdhc1grp { |
| 244 | fsl,pins = < |
| 245 | MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK 0x190 |
| 246 | MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d0 |
| 247 | MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d0 |
| 248 | MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d0 |
| 249 | MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d0 |
| 250 | MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d0 |
| 251 | MX8MM_IOMUXC_SD1_DATA4_USDHC1_DATA4 0x1d0 |
| 252 | MX8MM_IOMUXC_SD1_DATA5_USDHC1_DATA5 0x1d0 |
| 253 | MX8MM_IOMUXC_SD1_DATA6_USDHC1_DATA6 0x1d0 |
| 254 | MX8MM_IOMUXC_SD1_DATA7_USDHC1_DATA7 0x1d0 |
| 255 | MX8MM_IOMUXC_SD1_RESET_B_USDHC1_RESET_B 0x019 |
| 256 | MX8MM_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x190 |
| 257 | >; |
| 258 | }; |
| 259 | |
| 260 | pinctrl_usdhc1_100mhz: usdhc1-100mhzgrp { |
| 261 | fsl,pins = < |
| 262 | MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK 0x194 |
| 263 | MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d4 |
| 264 | MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d4 |
| 265 | MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d4 |
| 266 | MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d4 |
| 267 | MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d4 |
| 268 | MX8MM_IOMUXC_SD1_DATA4_USDHC1_DATA4 0x1d4 |
| 269 | MX8MM_IOMUXC_SD1_DATA5_USDHC1_DATA5 0x1d4 |
| 270 | MX8MM_IOMUXC_SD1_DATA6_USDHC1_DATA6 0x1d4 |
| 271 | MX8MM_IOMUXC_SD1_DATA7_USDHC1_DATA7 0x1d4 |
| 272 | MX8MM_IOMUXC_SD1_RESET_B_USDHC1_RESET_B 0x019 |
| 273 | MX8MM_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x194 |
| 274 | >; |
| 275 | }; |
| 276 | |
| 277 | pinctrl_usdhc1_200mhz: usdhc1-200mhzgrp { |
| 278 | fsl,pins = < |
| 279 | MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK 0x196 |
| 280 | MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d6 |
| 281 | MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d6 |
| 282 | MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d6 |
| 283 | MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d6 |
| 284 | MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d6 |
| 285 | MX8MM_IOMUXC_SD1_DATA4_USDHC1_DATA4 0x1d6 |
| 286 | MX8MM_IOMUXC_SD1_DATA5_USDHC1_DATA5 0x1d6 |
| 287 | MX8MM_IOMUXC_SD1_DATA6_USDHC1_DATA6 0x1d6 |
| 288 | MX8MM_IOMUXC_SD1_DATA7_USDHC1_DATA7 0x1d6 |
| 289 | MX8MM_IOMUXC_SD1_RESET_B_USDHC1_RESET_B 0x019 |
| 290 | MX8MM_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x196 |
| 291 | >; |
| 292 | }; |
| 293 | |
| 294 | pinctrl_wdog: wdoggrp { |
| 295 | fsl,pins = < |
| 296 | MX8MM_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0xc6 |
| 297 | >; |
| 298 | }; |
| 299 | }; |