| Chris Packham | 013e855 | 2018-05-08 22:34:12 +1200 | [diff] [blame^] | 1 | // SPDX-License-Identifier: GPL-2.0 |
| 2 | /dts-v1/; |
| 3 | |
| 4 | #include "kirkwood.dtsi" |
| 5 | #include "kirkwood-6281.dtsi" |
| 6 | |
| 7 | / { |
| 8 | model = "Seagate FreeAgent Dockstar"; |
| 9 | compatible = "seagate,dockstar", "marvell,kirkwood-88f6281", "marvell,kirkwood"; |
| 10 | |
| 11 | memory { |
| 12 | device_type = "memory"; |
| 13 | reg = <0x00000000 0x8000000>; |
| 14 | }; |
| 15 | |
| 16 | chosen { |
| 17 | bootargs = "console=ttyS0,115200n8 earlyprintk root=/dev/sda1 rootdelay=10"; |
| 18 | stdout-path = &uart0; |
| 19 | }; |
| 20 | |
| 21 | ocp@f1000000 { |
| 22 | pinctrl: pin-controller@10000 { |
| 23 | pmx_usb_power_enable: pmx-usb-power-enable { |
| 24 | marvell,pins = "mpp29"; |
| 25 | marvell,function = "gpio"; |
| 26 | }; |
| 27 | pmx_led_green: pmx-led-green { |
| 28 | marvell,pins = "mpp46"; |
| 29 | marvell,function = "gpio"; |
| 30 | }; |
| 31 | pmx_led_orange: pmx-led-orange { |
| 32 | marvell,pins = "mpp47"; |
| 33 | marvell,function = "gpio"; |
| 34 | }; |
| 35 | }; |
| 36 | serial@12000 { |
| 37 | status = "ok"; |
| 38 | }; |
| 39 | }; |
| 40 | gpio-leds { |
| 41 | compatible = "gpio-leds"; |
| 42 | pinctrl-0 = <&pmx_led_green &pmx_led_orange>; |
| 43 | pinctrl-names = "default"; |
| 44 | |
| 45 | health { |
| 46 | label = "status:green:health"; |
| 47 | gpios = <&gpio1 14 GPIO_ACTIVE_LOW>; |
| 48 | default-state = "keep"; |
| 49 | }; |
| 50 | fault { |
| 51 | label = "status:orange:fault"; |
| 52 | gpios = <&gpio1 15 GPIO_ACTIVE_LOW>; |
| 53 | }; |
| 54 | }; |
| 55 | regulators { |
| 56 | compatible = "simple-bus"; |
| 57 | #address-cells = <1>; |
| 58 | #size-cells = <0>; |
| 59 | pinctrl-0 = <&pmx_usb_power_enable>; |
| 60 | pinctrl-names = "default"; |
| 61 | |
| 62 | usb_power: regulator@1 { |
| 63 | compatible = "regulator-fixed"; |
| 64 | reg = <1>; |
| 65 | regulator-name = "USB Power"; |
| 66 | regulator-min-microvolt = <5000000>; |
| 67 | regulator-max-microvolt = <5000000>; |
| 68 | enable-active-high; |
| 69 | regulator-always-on; |
| 70 | regulator-boot-on; |
| 71 | gpio = <&gpio0 29 0>; |
| 72 | }; |
| 73 | }; |
| 74 | }; |
| 75 | |
| 76 | &nand { |
| 77 | status = "okay"; |
| 78 | |
| 79 | partition@0 { |
| 80 | label = "u-boot"; |
| 81 | reg = <0x0000000 0x100000>; |
| 82 | read-only; |
| 83 | }; |
| 84 | |
| 85 | partition@100000 { |
| 86 | label = "uImage"; |
| 87 | reg = <0x0100000 0x400000>; |
| 88 | }; |
| 89 | |
| 90 | partition@500000 { |
| 91 | label = "data"; |
| 92 | reg = <0x0500000 0xfb00000>; |
| 93 | }; |
| 94 | }; |
| 95 | |
| 96 | &mdio { |
| 97 | status = "okay"; |
| 98 | |
| 99 | ethphy0: ethernet-phy@0 { |
| 100 | compatible = "marvell,88e1116"; |
| 101 | reg = <0>; |
| 102 | }; |
| 103 | }; |
| 104 | |
| 105 | ð0 { |
| 106 | status = "okay"; |
| 107 | ethernet0-port@0 { |
| 108 | phy-handle = <ðphy0>; |
| 109 | }; |
| 110 | }; |