drivers/serial/serial_mtk.c - filogic/uboot - Gitiles

 // SPDX-License-Identifier: GPL-2.0
 /*
  * MediaTek High-speed UART driver
  *
  * Copyright (C) 2018 MediaTek Inc.
  * Author: Weijie Gao <weijie.gao@mediatek.com>
  */

 #include <clk.h>
 #include <common.h>
 #include <div64.h>
 #include <dm.h>
 #include <dm/device_compat.h>
 #include <errno.h>
 #include <log.h>
 #include <serial.h>
 #include <watchdog.h>
 #include <asm/global_data.h>
 #include <asm/io.h>
 #include <asm/types.h>
 #include <linux/err.h>

 struct mtk_serial_regs {
 	u32 rbr;
 	u32 ier;
 	u32 fcr;
 	u32 lcr;
 	u32 mcr;
 	u32 lsr;
 	u32 msr;
 	u32 spr;
 	u32 mdr1;
 	u32 highspeed;
 	u32 sample_count;
 	u32 sample_point;
 	u32 fracdiv_l;
 	u32 fracdiv_m;
 	u32 escape_en;
 	u32 guard;
 	u32 rx_sel;
 };

 #define thr rbr
 #define iir fcr
 #define dll rbr
 #define dlm ier

 #define UART_LCR_WLS_8	0x03		/* 8 bit character length */
 #define UART_LCR_DLAB	0x80		/* Divisor latch access bit */

 #define UART_LSR_DR	0x01		/* Data ready */
 #define UART_LSR_THRE	0x20		/* Xmit holding register empty */
 #define UART_LSR_TEMT	0x40		/* Xmitter empty */

 #define UART_MCR_DTR	0x01		/* DTR   */
 #define UART_MCR_RTS	0x02		/* RTS   */

 #define UART_FCR_FIFO_EN	0x01	/* Fifo enable */
 #define UART_FCR_RXSR		0x02	/* Receiver soft reset */
 #define UART_FCR_TXSR		0x04	/* Transmitter soft reset */

 #define UART_MCRVAL (UART_MCR_DTR | \
 		     UART_MCR_RTS)

 /* Clear & enable FIFOs */
 #define UART_FCRVAL (UART_FCR_FIFO_EN | \
 		     UART_FCR_RXSR |	\
 		     UART_FCR_TXSR)

 /* the data is correct if the real baud is within 3%. */
 #define BAUD_ALLOW_MAX(baud)	((baud) + (baud) * 3 / 100)
 #define BAUD_ALLOW_MIX(baud)	((baud) - (baud) * 3 / 100)

 /* struct mtk_serial_priv -	Structure holding all information used by the
  *				driver
  * @regs:			Register base of the serial port
  * @clk:			The baud clock device
  * @fixed_clk_rate:		Fallback fixed baud clock rate if baud clock
  *				device is not specified
  * @force_highspeed:		Force using high-speed mode
  */
 struct mtk_serial_priv {
 	struct mtk_serial_regs __iomem *regs;
 	struct clk clk;
 	u32 fixed_clk_rate;
 	bool force_highspeed;
 };

 static void _mtk_serial_setbrg(struct mtk_serial_priv *priv, int baud,
 			       uint clk_rate)
 {
 	u32 quot, realbaud, samplecount = 1;

 	/* Special case for low baud clock */
 	if (baud <= 115200 && clk_rate == 12000000) {
 		writel(3, &priv->regs->highspeed);

 		quot = DIV_ROUND_CLOSEST(clk_rate, 256 * baud);
 		if (quot == 0)
 			quot = 1;

 		samplecount = DIV_ROUND_CLOSEST(clk_rate, quot * baud);

 		realbaud = clk_rate / samplecount / quot;
 		if (realbaud > BAUD_ALLOW_MAX(baud) ||
 		    realbaud < BAUD_ALLOW_MIX(baud)) {
 			pr_info("baud %d can't be handled\n", baud);
 		}

 		goto set_baud;
 	}

 	if (priv->force_highspeed)
 		goto use_hs3;

 	if (baud <= 115200) {
 		writel(0, &priv->regs->highspeed);
 		quot = DIV_ROUND_CLOSEST(clk_rate, 16 * baud);
 	} else if (baud <= 576000) {
 		writel(2, &priv->regs->highspeed);

 		/* Set to next lower baudrate supported */
 		if ((baud == 500000) || (baud == 576000))
 			baud = 460800;

 		quot = DIV_ROUND_UP(clk_rate, 4 * baud);
 	} else {
 use_hs3:
 		writel(3, &priv->regs->highspeed);

 		quot = DIV_ROUND_UP(clk_rate, 256 * baud);
 		samplecount = DIV_ROUND_CLOSEST(clk_rate, quot * baud);
 	}

 set_baud:
 	/* set divisor */
 	writel(UART_LCR_WLS_8 | UART_LCR_DLAB, &priv->regs->lcr);
 	writel(quot & 0xff, &priv->regs->dll);
 	writel((quot >> 8) & 0xff, &priv->regs->dlm);
 	writel(UART_LCR_WLS_8, &priv->regs->lcr);

 	/* set highspeed mode sample count & point */
 	writel(samplecount - 1, &priv->regs->sample_count);
 	writel((samplecount - 2) >> 1, &priv->regs->sample_point);
 }

 static int _mtk_serial_putc(struct mtk_serial_priv *priv, const char ch)
 {
 	if (!(readl(&priv->regs->lsr) & UART_LSR_THRE))
 		return -EAGAIN;

 	writel(ch, &priv->regs->thr);

 	if (ch == '\n')
 		schedule();

 	return 0;
 }

 static int _mtk_serial_getc(struct mtk_serial_priv *priv)
 {
 	if (!(readl(&priv->regs->lsr) & UART_LSR_DR))
 		return -EAGAIN;

 	return readl(&priv->regs->rbr);
 }

 static int _mtk_serial_pending(struct mtk_serial_priv *priv, bool input)
 {
 	if (input)
 		return (readl(&priv->regs->lsr) & UART_LSR_DR) ? 1 : 0;
 	else
 		return (readl(&priv->regs->lsr) & UART_LSR_THRE) ? 0 : 1;
 }

 #if defined(CONFIG_DM_SERIAL) && \
 	(!defined(CONFIG_SPL_BUILD) || defined(CONFIG_SPL_DM))
 static int mtk_serial_setbrg(struct udevice *dev, int baudrate)
 {
 	struct mtk_serial_priv *priv = dev_get_priv(dev);
 	u32 clk_rate;

 	clk_rate = clk_get_rate(&priv->clk);
 	if (IS_ERR_VALUE(clk_rate) || clk_rate == 0)
 		clk_rate = priv->fixed_clk_rate;

 	_mtk_serial_setbrg(priv, baudrate, clk_rate);

 	return 0;
 }

 static int mtk_serial_putc(struct udevice *dev, const char ch)
 {
 	struct mtk_serial_priv *priv = dev_get_priv(dev);

 	return _mtk_serial_putc(priv, ch);
 }

 static int mtk_serial_getc(struct udevice *dev)
 {
 	struct mtk_serial_priv *priv = dev_get_priv(dev);

 	return _mtk_serial_getc(priv);
 }

 static int mtk_serial_pending(struct udevice *dev, bool input)
 {
 	struct mtk_serial_priv *priv = dev_get_priv(dev);

 	return _mtk_serial_pending(priv, input);
 }

 static int mtk_serial_probe(struct udevice *dev)
 {
 	struct mtk_serial_priv *priv = dev_get_priv(dev);

 	/* Disable interrupt */
 	writel(0, &priv->regs->ier);

 	writel(UART_MCRVAL, &priv->regs->mcr);
 	writel(UART_FCRVAL, &priv->regs->fcr);

 	return 0;
 }

 static int mtk_serial_of_to_plat(struct udevice *dev)
 {
 	struct mtk_serial_priv *priv = dev_get_priv(dev);
 	fdt_addr_t addr;
 	int err;

 	addr = dev_read_addr(dev);
 	if (addr == FDT_ADDR_T_NONE)
 		return -EINVAL;

 	priv->regs = map_physmem(addr, 0, MAP_NOCACHE);

 	err = clk_get_by_index(dev, 0, &priv->clk);
 	if (err) {
 		err = dev_read_u32(dev, "clock-frequency", &priv->fixed_clk_rate);
 		if (err) {
 			dev_err(dev, "baud clock not defined\n");
 			return -EINVAL;
 		}
 	} else {
 		err = clk_get_rate(&priv->clk);
 		if (IS_ERR_VALUE(err)) {
 			dev_err(dev, "invalid baud clock\n");
 			return -EINVAL;
 		}
 	}

 	priv->force_highspeed = dev_read_bool(dev, "mediatek,force-highspeed");

 	return 0;
 }

 static const struct dm_serial_ops mtk_serial_ops = {
 	.putc = mtk_serial_putc,
 	.pending = mtk_serial_pending,
 	.getc = mtk_serial_getc,
 	.setbrg = mtk_serial_setbrg,
 };

 static const struct udevice_id mtk_serial_ids[] = {
 	{ .compatible = "mediatek,hsuart" },
 	{ .compatible = "mediatek,mt6577-uart" },
 	{ }
 };

 U_BOOT_DRIVER(serial_mtk) = {
 	.name = "serial_mtk",
 	.id = UCLASS_SERIAL,
 	.of_match = mtk_serial_ids,
 	.of_to_plat = mtk_serial_of_to_plat,
 	.priv_auto	= sizeof(struct mtk_serial_priv),
 	.probe = mtk_serial_probe,
 	.ops = &mtk_serial_ops,
 	.flags = DM_FLAG_PRE_RELOC,
 };
 #else

 DECLARE_GLOBAL_DATA_PTR;

 #define DECLARE_HSUART_PRIV(port) \
 	static struct mtk_serial_priv mtk_hsuart##port = { \
 	.regs = (struct mtk_serial_regs *)CFG_SYS_NS16550_COM##port, \
 	.fixed_clk_rate = CFG_SYS_NS16550_CLK \
 };

 #define DECLARE_HSUART_FUNCTIONS(port) \
 	static int mtk_serial##port##_init(void) \
 	{ \
 		writel(0, &mtk_hsuart##port.regs->ier); \
 		writel(UART_MCRVAL, &mtk_hsuart##port.regs->mcr); \
 		writel(UART_FCRVAL, &mtk_hsuart##port.regs->fcr); \
 		_mtk_serial_setbrg(&mtk_hsuart##port, gd->baudrate, \
 				   mtk_hsuart##port.fixed_clk_rate); \
 		return 0 ; \
 	} \
 	static void mtk_serial##port##_setbrg(void) \
 	{ \
 		_mtk_serial_setbrg(&mtk_hsuart##port, gd->baudrate, \
 				   mtk_hsuart##port.fixed_clk_rate); \
 	} \
 	static int mtk_serial##port##_getc(void) \
 	{ \
 		int err; \
 		do { \
 			err = _mtk_serial_getc(&mtk_hsuart##port); \
 			if (err == -EAGAIN) \
 				schedule(); \
 		} while (err == -EAGAIN); \
 		return err >= 0 ? err : 0; \
 	} \
 	static int mtk_serial##port##_tstc(void) \
 	{ \
 		return _mtk_serial_pending(&mtk_hsuart##port, true); \
 	} \
 	static void mtk_serial##port##_putc(const char c) \
 	{ \
 		int err; \
 		if (c == '\n') \
 			mtk_serial##port##_putc('\r'); \
 		do { \
 			err = _mtk_serial_putc(&mtk_hsuart##port, c); \
 		} while (err == -EAGAIN); \
 	} \
 	static void mtk_serial##port##_puts(const char *s) \
 	{ \
 		while (*s) { \
 			mtk_serial##port##_putc(*s++); \
 		} \
 	}

 /* Serial device descriptor */
 #define INIT_HSUART_STRUCTURE(port, __name) {	\
 	.name	= __name,			\
 	.start	= mtk_serial##port##_init,	\
 	.stop	= NULL,				\
 	.setbrg	= mtk_serial##port##_setbrg,	\
 	.getc	= mtk_serial##port##_getc,	\
 	.tstc	= mtk_serial##port##_tstc,	\
 	.putc	= mtk_serial##port##_putc,	\
 	.puts	= mtk_serial##port##_puts,	\
 }

 #define DECLARE_HSUART(port, __name) \
 	DECLARE_HSUART_PRIV(port); \
 	DECLARE_HSUART_FUNCTIONS(port); \
 	struct serial_device mtk_hsuart##port##_device = \
 		INIT_HSUART_STRUCTURE(port, __name);

 #if !defined(CONFIG_CONS_INDEX)
 #elif (CONFIG_CONS_INDEX < 1) || (CONFIG_CONS_INDEX > 6)
 #error	"Invalid console index value."
 #endif

 #if CONFIG_CONS_INDEX == 1 && !defined(CFG_SYS_NS16550_COM1)
 #error	"Console port 1 defined but not configured."
 #elif CONFIG_CONS_INDEX == 2 && !defined(CFG_SYS_NS16550_COM2)
 #error	"Console port 2 defined but not configured."
 #elif CONFIG_CONS_INDEX == 3 && !defined(CFG_SYS_NS16550_COM3)
 #error	"Console port 3 defined but not configured."
 #elif CONFIG_CONS_INDEX == 4 && !defined(CFG_SYS_NS16550_COM4)
 #error	"Console port 4 defined but not configured."
 #elif CONFIG_CONS_INDEX == 5 && !defined(CFG_SYS_NS16550_COM5)
 #error	"Console port 5 defined but not configured."
 #elif CONFIG_CONS_INDEX == 6 && !defined(CFG_SYS_NS16550_COM6)
 #error	"Console port 6 defined but not configured."
 #endif

 #if defined(CFG_SYS_NS16550_COM1)
 DECLARE_HSUART(1, "mtk-hsuart0");
 #endif
 #if defined(CFG_SYS_NS16550_COM2)
 DECLARE_HSUART(2, "mtk-hsuart1");
 #endif
 #if defined(CFG_SYS_NS16550_COM3)
 DECLARE_HSUART(3, "mtk-hsuart2");
 #endif
 #if defined(CFG_SYS_NS16550_COM4)
 DECLARE_HSUART(4, "mtk-hsuart3");
 #endif
 #if defined(CFG_SYS_NS16550_COM5)
 DECLARE_HSUART(5, "mtk-hsuart4");
 #endif
 #if defined(CFG_SYS_NS16550_COM6)
 DECLARE_HSUART(6, "mtk-hsuart5");
 #endif

 __weak struct serial_device *default_serial_console(void)
 {
 #if CONFIG_CONS_INDEX == 1
 	return &mtk_hsuart1_device;
 #elif CONFIG_CONS_INDEX == 2
 	return &mtk_hsuart2_device;
 #elif CONFIG_CONS_INDEX == 3
 	return &mtk_hsuart3_device;
 #elif CONFIG_CONS_INDEX == 4
 	return &mtk_hsuart4_device;
 #elif CONFIG_CONS_INDEX == 5
 	return &mtk_hsuart5_device;
 #elif CONFIG_CONS_INDEX == 6
 	return &mtk_hsuart6_device;
 #else
 #error "Bad CONFIG_CONS_INDEX."
 #endif
 }

 void mtk_serial_initialize(void)
 {
 #if defined(CFG_SYS_NS16550_COM1)
 	serial_register(&mtk_hsuart1_device);
 #endif
 #if defined(CFG_SYS_NS16550_COM2)
 	serial_register(&mtk_hsuart2_device);
 #endif
 #if defined(CFG_SYS_NS16550_COM3)
 	serial_register(&mtk_hsuart3_device);
 #endif
 #if defined(CFG_SYS_NS16550_COM4)
 	serial_register(&mtk_hsuart4_device);
 #endif
 #if defined(CFG_SYS_NS16550_COM5)
 	serial_register(&mtk_hsuart5_device);
 #endif
 #if defined(CFG_SYS_NS16550_COM6)
 	serial_register(&mtk_hsuart6_device);
 #endif
 }

 #endif

 #ifdef CONFIG_DEBUG_UART_MTK

 #include <debug_uart.h>

 static inline void _debug_uart_init(void)
 {
 	struct mtk_serial_priv priv;

 	priv.regs = (void *) CONFIG_VAL(DEBUG_UART_BASE);
 	priv.fixed_clk_rate = CONFIG_DEBUG_UART_CLOCK;

 	writel(0, &priv.regs->ier);
 	writel(UART_MCRVAL, &priv.regs->mcr);
 	writel(UART_FCRVAL, &priv.regs->fcr);

 	_mtk_serial_setbrg(&priv, CONFIG_BAUDRATE, priv.fixed_clk_rate);
 }

 static inline void _debug_uart_putc(int ch)
 {
 	struct mtk_serial_regs __iomem *regs =
 		(void *) CONFIG_VAL(DEBUG_UART_BASE);

 	while (!(readl(&regs->lsr) & UART_LSR_THRE))
 		;

 	writel(ch, &regs->thr);
 }

 DEBUG_UART_FUNCS

 #endif
	// SPDX-License-Identifier: GPL-2.0
	/*
	* MediaTek High-speed UART driver
	*
	* Copyright (C) 2018 MediaTek Inc.
	* Author: Weijie Gao <weijie.gao@mediatek.com>
	*/

	#include <clk.h>
	#include <common.h>
	#include <div64.h>
	#include <dm.h>
	#include <dm/device_compat.h>
	#include <errno.h>
	#include <log.h>
	#include <serial.h>
	#include <watchdog.h>
	#include <asm/global_data.h>
	#include <asm/io.h>
	#include <asm/types.h>
	#include <linux/err.h>

	struct mtk_serial_regs {
	u32 rbr;
	u32 ier;
	u32 fcr;
	u32 lcr;
	u32 mcr;
	u32 lsr;
	u32 msr;
	u32 spr;
	u32 mdr1;
	u32 highspeed;
	u32 sample_count;
	u32 sample_point;
	u32 fracdiv_l;
	u32 fracdiv_m;
	u32 escape_en;
	u32 guard;
	u32 rx_sel;
	};

	#define thr rbr
	#define iir fcr
	#define dll rbr
	#define dlm ier

	#define UART_LCR_WLS_8 0x03 /* 8 bit character length */
	#define UART_LCR_DLAB 0x80 /* Divisor latch access bit */

	#define UART_LSR_DR 0x01 /* Data ready */
	#define UART_LSR_THRE 0x20 /* Xmit holding register empty */
	#define UART_LSR_TEMT 0x40 /* Xmitter empty */

	#define UART_MCR_DTR 0x01 /* DTR */
	#define UART_MCR_RTS 0x02 /* RTS */

	#define UART_FCR_FIFO_EN 0x01 /* Fifo enable */
	#define UART_FCR_RXSR 0x02 /* Receiver soft reset */
	#define UART_FCR_TXSR 0x04 /* Transmitter soft reset */

	#define UART_MCRVAL (UART_MCR_DTR \| \
	UART_MCR_RTS)

	/* Clear & enable FIFOs */
	#define UART_FCRVAL (UART_FCR_FIFO_EN \| \
	UART_FCR_RXSR \| \
	UART_FCR_TXSR)

	/* the data is correct if the real baud is within 3%. */
	#define BAUD_ALLOW_MAX(baud) ((baud) + (baud) * 3 / 100)
	#define BAUD_ALLOW_MIX(baud) ((baud) - (baud) * 3 / 100)

	/* struct mtk_serial_priv - Structure holding all information used by the
	* driver
	* @regs: Register base of the serial port
	* @clk: The baud clock device
	* @fixed_clk_rate: Fallback fixed baud clock rate if baud clock
	* device is not specified
	* @force_highspeed: Force using high-speed mode
	*/
	struct mtk_serial_priv {
	struct mtk_serial_regs __iomem *regs;
	struct clk clk;
	u32 fixed_clk_rate;
	bool force_highspeed;
	};

	static void _mtk_serial_setbrg(struct mtk_serial_priv *priv, int baud,
	uint clk_rate)
	{
	u32 quot, realbaud, samplecount = 1;

	/* Special case for low baud clock */
	if (baud <= 115200 && clk_rate == 12000000) {
	writel(3, &priv->regs->highspeed);

	quot = DIV_ROUND_CLOSEST(clk_rate, 256 * baud);
	if (quot == 0)
	quot = 1;

	samplecount = DIV_ROUND_CLOSEST(clk_rate, quot * baud);

	realbaud = clk_rate / samplecount / quot;
	if (realbaud > BAUD_ALLOW_MAX(baud) \|\|
	realbaud < BAUD_ALLOW_MIX(baud)) {
	pr_info("baud %d can't be handled\n", baud);
	}

	goto set_baud;
	}

	if (priv->force_highspeed)
	goto use_hs3;

	if (baud <= 115200) {
	writel(0, &priv->regs->highspeed);
	quot = DIV_ROUND_CLOSEST(clk_rate, 16 * baud);
	} else if (baud <= 576000) {
	writel(2, &priv->regs->highspeed);

	/* Set to next lower baudrate supported */
	if ((baud == 500000) \|\| (baud == 576000))
	baud = 460800;

	quot = DIV_ROUND_UP(clk_rate, 4 * baud);
	} else {
	use_hs3:
	writel(3, &priv->regs->highspeed);

	quot = DIV_ROUND_UP(clk_rate, 256 * baud);
	samplecount = DIV_ROUND_CLOSEST(clk_rate, quot * baud);
	}

	set_baud:
	/* set divisor */
	writel(UART_LCR_WLS_8 \| UART_LCR_DLAB, &priv->regs->lcr);
	writel(quot & 0xff, &priv->regs->dll);
	writel((quot >> 8) & 0xff, &priv->regs->dlm);
	writel(UART_LCR_WLS_8, &priv->regs->lcr);

	/* set highspeed mode sample count & point */
	writel(samplecount - 1, &priv->regs->sample_count);
	writel((samplecount - 2) >> 1, &priv->regs->sample_point);
	}

	static int _mtk_serial_putc(struct mtk_serial_priv *priv, const char ch)
	{
	if (!(readl(&priv->regs->lsr) & UART_LSR_THRE))
	return -EAGAIN;

	writel(ch, &priv->regs->thr);

	if (ch == '\n')
	schedule();

	return 0;
	}

	static int _mtk_serial_getc(struct mtk_serial_priv *priv)
	{
	if (!(readl(&priv->regs->lsr) & UART_LSR_DR))
	return -EAGAIN;

	return readl(&priv->regs->rbr);
	}

	static int _mtk_serial_pending(struct mtk_serial_priv *priv, bool input)
	{
	if (input)
	return (readl(&priv->regs->lsr) & UART_LSR_DR) ? 1 : 0;
	else
	return (readl(&priv->regs->lsr) & UART_LSR_THRE) ? 0 : 1;
	}

	#if defined(CONFIG_DM_SERIAL) && \
	(!defined(CONFIG_SPL_BUILD) \|\| defined(CONFIG_SPL_DM))
	static int mtk_serial_setbrg(struct udevice *dev, int baudrate)
	{
	struct mtk_serial_priv *priv = dev_get_priv(dev);
	u32 clk_rate;

	clk_rate = clk_get_rate(&priv->clk);
	if (IS_ERR_VALUE(clk_rate) \|\| clk_rate == 0)
	clk_rate = priv->fixed_clk_rate;

	_mtk_serial_setbrg(priv, baudrate, clk_rate);

	return 0;
	}

	static int mtk_serial_putc(struct udevice *dev, const char ch)
	{
	struct mtk_serial_priv *priv = dev_get_priv(dev);

	return _mtk_serial_putc(priv, ch);
	}

	static int mtk_serial_getc(struct udevice *dev)
	{
	struct mtk_serial_priv *priv = dev_get_priv(dev);

	return _mtk_serial_getc(priv);
	}

	static int mtk_serial_pending(struct udevice *dev, bool input)
	{
	struct mtk_serial_priv *priv = dev_get_priv(dev);

	return _mtk_serial_pending(priv, input);
	}

	static int mtk_serial_probe(struct udevice *dev)
	{
	struct mtk_serial_priv *priv = dev_get_priv(dev);

	/* Disable interrupt */
	writel(0, &priv->regs->ier);

	writel(UART_MCRVAL, &priv->regs->mcr);
	writel(UART_FCRVAL, &priv->regs->fcr);

	return 0;
	}

	static int mtk_serial_of_to_plat(struct udevice *dev)
	{
	struct mtk_serial_priv *priv = dev_get_priv(dev);
	fdt_addr_t addr;
	int err;

	addr = dev_read_addr(dev);
	if (addr == FDT_ADDR_T_NONE)
	return -EINVAL;

	priv->regs = map_physmem(addr, 0, MAP_NOCACHE);

	err = clk_get_by_index(dev, 0, &priv->clk);
	if (err) {
	err = dev_read_u32(dev, "clock-frequency", &priv->fixed_clk_rate);
	if (err) {
	dev_err(dev, "baud clock not defined\n");
	return -EINVAL;
	}
	} else {
	err = clk_get_rate(&priv->clk);
	if (IS_ERR_VALUE(err)) {
	dev_err(dev, "invalid baud clock\n");
	return -EINVAL;
	}
	}

	priv->force_highspeed = dev_read_bool(dev, "mediatek,force-highspeed");

	return 0;
	}

	static const struct dm_serial_ops mtk_serial_ops = {
	.putc = mtk_serial_putc,
	.pending = mtk_serial_pending,
	.getc = mtk_serial_getc,
	.setbrg = mtk_serial_setbrg,
	};

	static const struct udevice_id mtk_serial_ids[] = {
	{ .compatible = "mediatek,hsuart" },
	{ .compatible = "mediatek,mt6577-uart" },
	{ }
	};

	U_BOOT_DRIVER(serial_mtk) = {
	.name = "serial_mtk",
	.id = UCLASS_SERIAL,
	.of_match = mtk_serial_ids,
	.of_to_plat = mtk_serial_of_to_plat,
	.priv_auto = sizeof(struct mtk_serial_priv),
	.probe = mtk_serial_probe,
	.ops = &mtk_serial_ops,
	.flags = DM_FLAG_PRE_RELOC,
	};
	#else

	DECLARE_GLOBAL_DATA_PTR;

	#define DECLARE_HSUART_PRIV(port) \
	static struct mtk_serial_priv mtk_hsuart##port = { \
	.regs = (struct mtk_serial_regs *)CFG_SYS_NS16550_COM##port, \
	.fixed_clk_rate = CFG_SYS_NS16550_CLK \
	};

	#define DECLARE_HSUART_FUNCTIONS(port) \
	static int mtk_serial##port##_init(void) \
	{ \
	writel(0, &mtk_hsuart##port.regs->ier); \
	writel(UART_MCRVAL, &mtk_hsuart##port.regs->mcr); \
	writel(UART_FCRVAL, &mtk_hsuart##port.regs->fcr); \
	_mtk_serial_setbrg(&mtk_hsuart##port, gd->baudrate, \
	mtk_hsuart##port.fixed_clk_rate); \
	return 0 ; \
	} \
	static void mtk_serial##port##_setbrg(void) \
	{ \
	_mtk_serial_setbrg(&mtk_hsuart##port, gd->baudrate, \
	mtk_hsuart##port.fixed_clk_rate); \
	} \
	static int mtk_serial##port##_getc(void) \
	{ \
	int err; \
	do { \
	err = _mtk_serial_getc(&mtk_hsuart##port); \
	if (err == -EAGAIN) \
	schedule(); \
	} while (err == -EAGAIN); \
	return err >= 0 ? err : 0; \
	} \
	static int mtk_serial##port##_tstc(void) \
	{ \
	return _mtk_serial_pending(&mtk_hsuart##port, true); \
	} \
	static void mtk_serial##port##_putc(const char c) \
	{ \
	int err; \
	if (c == '\n') \
	mtk_serial##port##_putc('\r'); \
	do { \
	err = _mtk_serial_putc(&mtk_hsuart##port, c); \
	} while (err == -EAGAIN); \
	} \
	static void mtk_serial##port##_puts(const char *s) \
	{ \
	while (*s) { \
	mtk_serial##port##_putc(*s++); \
	} \
	}

	/* Serial device descriptor */
	#define INIT_HSUART_STRUCTURE(port, __name) { \
	.name = __name, \
	.start = mtk_serial##port##_init, \
	.stop = NULL, \
	.setbrg = mtk_serial##port##_setbrg, \
	.getc = mtk_serial##port##_getc, \
	.tstc = mtk_serial##port##_tstc, \
	.putc = mtk_serial##port##_putc, \
	.puts = mtk_serial##port##_puts, \
	}

	#define DECLARE_HSUART(port, __name) \
	DECLARE_HSUART_PRIV(port); \
	DECLARE_HSUART_FUNCTIONS(port); \
	struct serial_device mtk_hsuart##port##_device = \
	INIT_HSUART_STRUCTURE(port, __name);

	#if !defined(CONFIG_CONS_INDEX)
	#elif (CONFIG_CONS_INDEX < 1) \|\| (CONFIG_CONS_INDEX > 6)
	#error "Invalid console index value."
	#endif

	#if CONFIG_CONS_INDEX == 1 && !defined(CFG_SYS_NS16550_COM1)
	#error "Console port 1 defined but not configured."
	#elif CONFIG_CONS_INDEX == 2 && !defined(CFG_SYS_NS16550_COM2)
	#error "Console port 2 defined but not configured."
	#elif CONFIG_CONS_INDEX == 3 && !defined(CFG_SYS_NS16550_COM3)
	#error "Console port 3 defined but not configured."
	#elif CONFIG_CONS_INDEX == 4 && !defined(CFG_SYS_NS16550_COM4)
	#error "Console port 4 defined but not configured."
	#elif CONFIG_CONS_INDEX == 5 && !defined(CFG_SYS_NS16550_COM5)
	#error "Console port 5 defined but not configured."
	#elif CONFIG_CONS_INDEX == 6 && !defined(CFG_SYS_NS16550_COM6)
	#error "Console port 6 defined but not configured."
	#endif

	#if defined(CFG_SYS_NS16550_COM1)
	DECLARE_HSUART(1, "mtk-hsuart0");
	#endif
	#if defined(CFG_SYS_NS16550_COM2)
	DECLARE_HSUART(2, "mtk-hsuart1");
	#endif
	#if defined(CFG_SYS_NS16550_COM3)
	DECLARE_HSUART(3, "mtk-hsuart2");
	#endif
	#if defined(CFG_SYS_NS16550_COM4)
	DECLARE_HSUART(4, "mtk-hsuart3");
	#endif
	#if defined(CFG_SYS_NS16550_COM5)
	DECLARE_HSUART(5, "mtk-hsuart4");
	#endif
	#if defined(CFG_SYS_NS16550_COM6)
	DECLARE_HSUART(6, "mtk-hsuart5");
	#endif

	__weak struct serial_device *default_serial_console(void)
	{
	#if CONFIG_CONS_INDEX == 1
	return &mtk_hsuart1_device;
	#elif CONFIG_CONS_INDEX == 2
	return &mtk_hsuart2_device;
	#elif CONFIG_CONS_INDEX == 3
	return &mtk_hsuart3_device;
	#elif CONFIG_CONS_INDEX == 4
	return &mtk_hsuart4_device;
	#elif CONFIG_CONS_INDEX == 5
	return &mtk_hsuart5_device;
	#elif CONFIG_CONS_INDEX == 6
	return &mtk_hsuart6_device;
	#else
	#error "Bad CONFIG_CONS_INDEX."
	#endif
	}

	void mtk_serial_initialize(void)
	{
	#if defined(CFG_SYS_NS16550_COM1)
	serial_register(&mtk_hsuart1_device);
	#endif
	#if defined(CFG_SYS_NS16550_COM2)
	serial_register(&mtk_hsuart2_device);
	#endif
	#if defined(CFG_SYS_NS16550_COM3)
	serial_register(&mtk_hsuart3_device);
	#endif
	#if defined(CFG_SYS_NS16550_COM4)
	serial_register(&mtk_hsuart4_device);
	#endif
	#if defined(CFG_SYS_NS16550_COM5)
	serial_register(&mtk_hsuart5_device);
	#endif
	#if defined(CFG_SYS_NS16550_COM6)
	serial_register(&mtk_hsuart6_device);
	#endif
	}

	#endif

	#ifdef CONFIG_DEBUG_UART_MTK

	#include <debug_uart.h>

	static inline void _debug_uart_init(void)
	{
	struct mtk_serial_priv priv;

	priv.regs = (void *) CONFIG_VAL(DEBUG_UART_BASE);
	priv.fixed_clk_rate = CONFIG_DEBUG_UART_CLOCK;

	writel(0, &priv.regs->ier);
	writel(UART_MCRVAL, &priv.regs->mcr);
	writel(UART_FCRVAL, &priv.regs->fcr);

	_mtk_serial_setbrg(&priv, CONFIG_BAUDRATE, priv.fixed_clk_rate);
	}

	static inline void _debug_uart_putc(int ch)
	{
	struct mtk_serial_regs __iomem *regs =
	(void *) CONFIG_VAL(DEBUG_UART_BASE);

	while (!(readl(&regs->lsr) & UART_LSR_THRE))
	;

	writel(ch, &regs->thr);
	}

	DEBUG_UART_FUNCS

	#endif