| // SPDX-License-Identifier: GPL-2.0+ |
| /* |
| * Copyright (C) 2010-2013 Freescale Semiconductor, Inc. |
| * Copyright (C) 2013, Boundary Devices <info@boundarydevices.com> |
| * Copyright (C) 2014-2019, Toradex AG |
| * copied from nitrogen6x |
| */ |
| |
| #include <config.h> |
| #include <cpu_func.h> |
| #include <dm.h> |
| #include <image.h> |
| #include <init.h> |
| #include <net.h> |
| #include <asm/global_data.h> |
| #include <linux/bitops.h> |
| #include <linux/delay.h> |
| |
| #include <ahci.h> |
| #include <asm/arch/clock.h> |
| #include <asm/arch/crm_regs.h> |
| #include <asm/arch/imx-regs.h> |
| #include <asm/arch/mx6-ddr.h> |
| #include <asm/arch/mx6-pins.h> |
| #include <asm/arch/mxc_hdmi.h> |
| #include <asm/arch/sys_proto.h> |
| #include <asm/bootm.h> |
| #include <asm/gpio.h> |
| #include <asm/mach-imx/boot_mode.h> |
| #include <asm/mach-imx/iomux-v3.h> |
| #include <asm/mach-imx/sata.h> |
| #include <asm/mach-imx/video.h> |
| #include <asm/sections.h> |
| #include <dm/device-internal.h> |
| #include <dm/platform_data/serial_mxc.h> |
| #include <dwc_ahsata.h> |
| #include <env.h> |
| #include <fsl_esdhc_imx.h> |
| #include <imx_thermal.h> |
| #include <micrel.h> |
| #include <miiphy.h> |
| #include <netdev.h> |
| |
| #include "../common/tdx-cfg-block.h" |
| #ifdef CONFIG_TDX_CMD_IMX_MFGR |
| #include "pf0100.h" |
| #endif |
| |
| DECLARE_GLOBAL_DATA_PTR; |
| |
| #define UART_PAD_CTRL (PAD_CTL_PUS_100K_UP | \ |
| PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \ |
| PAD_CTL_SRE_FAST | PAD_CTL_HYS) |
| |
| #define USDHC_PAD_CTRL (PAD_CTL_PUS_47K_UP | \ |
| PAD_CTL_SPEED_LOW | PAD_CTL_DSE_40ohm | \ |
| PAD_CTL_SRE_FAST | PAD_CTL_HYS) |
| |
| #define USDHC_EMMC_PAD_CTRL (PAD_CTL_PUS_47K_UP | \ |
| PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm | \ |
| PAD_CTL_SRE_FAST | PAD_CTL_HYS) |
| |
| #define ENET_PAD_CTRL (PAD_CTL_PUS_100K_UP | \ |
| PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS) |
| |
| #define WEAK_PULLUP (PAD_CTL_PUS_100K_UP | \ |
| PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \ |
| PAD_CTL_SRE_SLOW) |
| |
| #define WEAK_PULLDOWN (PAD_CTL_PUS_100K_DOWN | \ |
| PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \ |
| PAD_CTL_HYS | PAD_CTL_SRE_SLOW) |
| |
| #define TRISTATE (PAD_CTL_HYS | PAD_CTL_SPEED_MED) |
| |
| #define OUTPUT_RGB (PAD_CTL_SPEED_MED|PAD_CTL_DSE_60ohm|PAD_CTL_SRE_FAST) |
| |
| #define APALIS_IMX6_SATA_INIT_RETRIES 10 |
| |
| int dram_init(void) |
| { |
| /* use the DDR controllers configured size */ |
| gd->ram_size = get_ram_size((void *)CFG_SYS_SDRAM_BASE, |
| (ulong)imx_ddr_size()); |
| |
| return 0; |
| } |
| |
| /* Apalis UART1 */ |
| iomux_v3_cfg_t const uart1_pads_dce[] = { |
| MX6_PAD_CSI0_DAT10__UART1_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), |
| MX6_PAD_CSI0_DAT11__UART1_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), |
| }; |
| iomux_v3_cfg_t const uart1_pads_dte[] = { |
| MX6_PAD_CSI0_DAT10__UART1_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), |
| MX6_PAD_CSI0_DAT11__UART1_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), |
| }; |
| |
| #if defined(CONFIG_FSL_ESDHC_IMX) && defined(CONFIG_SPL_BUILD) |
| /* Apalis MMC1 */ |
| iomux_v3_cfg_t const usdhc1_pads[] = { |
| MX6_PAD_SD1_CLK__SD1_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), |
| MX6_PAD_SD1_CMD__SD1_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), |
| MX6_PAD_SD1_DAT0__SD1_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL), |
| MX6_PAD_SD1_DAT1__SD1_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL), |
| MX6_PAD_SD1_DAT2__SD1_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL), |
| MX6_PAD_SD1_DAT3__SD1_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL), |
| MX6_PAD_NANDF_D0__SD1_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL), |
| MX6_PAD_NANDF_D1__SD1_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL), |
| MX6_PAD_NANDF_D2__SD1_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL), |
| MX6_PAD_NANDF_D3__SD1_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL), |
| MX6_PAD_DI0_PIN4__GPIO4_IO20 | MUX_PAD_CTRL(NO_PAD_CTRL), /* CD */ |
| # define GPIO_MMC_CD IMX_GPIO_NR(4, 20) |
| }; |
| |
| /* Apalis SD1 */ |
| iomux_v3_cfg_t const usdhc2_pads[] = { |
| MX6_PAD_SD2_CLK__SD2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), |
| MX6_PAD_SD2_CMD__SD2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), |
| MX6_PAD_SD2_DAT0__SD2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL), |
| MX6_PAD_SD2_DAT1__SD2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL), |
| MX6_PAD_SD2_DAT2__SD2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL), |
| MX6_PAD_SD2_DAT3__SD2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL), |
| MX6_PAD_NANDF_CS1__GPIO6_IO14 | MUX_PAD_CTRL(NO_PAD_CTRL), /* CD */ |
| # define GPIO_SD_CD IMX_GPIO_NR(6, 14) |
| }; |
| |
| /* eMMC */ |
| iomux_v3_cfg_t const usdhc3_pads[] = { |
| MX6_PAD_SD3_CLK__SD3_CLK | MUX_PAD_CTRL(USDHC_EMMC_PAD_CTRL), |
| MX6_PAD_SD3_CMD__SD3_CMD | MUX_PAD_CTRL(USDHC_EMMC_PAD_CTRL), |
| MX6_PAD_SD3_DAT0__SD3_DATA0 | MUX_PAD_CTRL(USDHC_EMMC_PAD_CTRL), |
| MX6_PAD_SD3_DAT1__SD3_DATA1 | MUX_PAD_CTRL(USDHC_EMMC_PAD_CTRL), |
| MX6_PAD_SD3_DAT2__SD3_DATA2 | MUX_PAD_CTRL(USDHC_EMMC_PAD_CTRL), |
| MX6_PAD_SD3_DAT3__SD3_DATA3 | MUX_PAD_CTRL(USDHC_EMMC_PAD_CTRL), |
| MX6_PAD_SD3_DAT4__SD3_DATA4 | MUX_PAD_CTRL(USDHC_EMMC_PAD_CTRL), |
| MX6_PAD_SD3_DAT5__SD3_DATA5 | MUX_PAD_CTRL(USDHC_EMMC_PAD_CTRL), |
| MX6_PAD_SD3_DAT6__SD3_DATA6 | MUX_PAD_CTRL(USDHC_EMMC_PAD_CTRL), |
| MX6_PAD_SD3_DAT7__SD3_DATA7 | MUX_PAD_CTRL(USDHC_EMMC_PAD_CTRL), |
| MX6_PAD_SD3_RST__GPIO7_IO08 | MUX_PAD_CTRL(WEAK_PULLUP) | MUX_MODE_SION, |
| }; |
| #endif /* CONFIG_FSL_ESDHC_IMX & CONFIG_SPL_BUILD */ |
| |
| int mx6_rgmii_rework(struct phy_device *phydev) |
| { |
| int tmp; |
| |
| switch (ksz9xx1_phy_get_id(phydev) & MII_KSZ9x31_SILICON_REV_MASK) { |
| case PHY_ID_KSZ9131: |
| /* read rxc dll control - devaddr = 0x02, register = 0x4c */ |
| tmp = ksz9031_phy_extended_read(phydev, 0x02, |
| MII_KSZ9131_EXT_RGMII_2NS_SKEW_RXDLL, |
| MII_KSZ9031_MOD_DATA_NO_POST_INC); |
| /* disable rxdll bypass (enable 2ns skew delay on RXC) */ |
| tmp &= ~MII_KSZ9131_RXTXDLL_BYPASS; |
| /* rxc data pad skew 2ns - devaddr = 0x02, register = 0x4c */ |
| ksz9031_phy_extended_write(phydev, 0x02, |
| MII_KSZ9131_EXT_RGMII_2NS_SKEW_RXDLL, |
| MII_KSZ9031_MOD_DATA_NO_POST_INC, |
| tmp); |
| /* read txc dll control - devaddr = 0x02, register = 0x4d */ |
| tmp = ksz9031_phy_extended_read(phydev, 0x02, |
| MII_KSZ9131_EXT_RGMII_2NS_SKEW_TXDLL, |
| MII_KSZ9031_MOD_DATA_NO_POST_INC); |
| /* disable rxdll bypass (enable 2ns skew delay on TXC) */ |
| tmp &= ~MII_KSZ9131_RXTXDLL_BYPASS; |
| /* txc data pad skew 2ns - devaddr = 0x02, register = 0x4d */ |
| ksz9031_phy_extended_write(phydev, 0x02, |
| MII_KSZ9131_EXT_RGMII_2NS_SKEW_TXDLL, |
| MII_KSZ9031_MOD_DATA_NO_POST_INC, |
| tmp); |
| |
| /* control data pad skew - devaddr = 0x02, register = 0x04 */ |
| ksz9031_phy_extended_write(phydev, 0x02, |
| MII_KSZ9031_EXT_RGMII_CTRL_SIG_SKEW, |
| MII_KSZ9031_MOD_DATA_NO_POST_INC, |
| 0x007d); |
| /* rx data pad skew - devaddr = 0x02, register = 0x05 */ |
| ksz9031_phy_extended_write(phydev, 0x02, |
| MII_KSZ9031_EXT_RGMII_RX_DATA_SKEW, |
| MII_KSZ9031_MOD_DATA_NO_POST_INC, |
| 0x7777); |
| /* tx data pad skew - devaddr = 0x02, register = 0x05 */ |
| ksz9031_phy_extended_write(phydev, 0x02, |
| MII_KSZ9031_EXT_RGMII_TX_DATA_SKEW, |
| MII_KSZ9031_MOD_DATA_NO_POST_INC, |
| 0xdddd); |
| /* gtx and rx clock pad skew - devaddr = 0x02,register = 0x08 */ |
| ksz9031_phy_extended_write(phydev, 0x02, |
| MII_KSZ9031_EXT_RGMII_CLOCK_SKEW, |
| MII_KSZ9031_MOD_DATA_NO_POST_INC, |
| 0x0007); |
| break; |
| case PHY_ID_KSZ9031: |
| default: |
| /* control data pad skew - devaddr = 0x02, register = 0x04 */ |
| ksz9031_phy_extended_write(phydev, 0x02, |
| MII_KSZ9031_EXT_RGMII_CTRL_SIG_SKEW, |
| MII_KSZ9031_MOD_DATA_NO_POST_INC, |
| 0x0000); |
| /* rx data pad skew - devaddr = 0x02, register = 0x05 */ |
| ksz9031_phy_extended_write(phydev, 0x02, |
| MII_KSZ9031_EXT_RGMII_RX_DATA_SKEW, |
| MII_KSZ9031_MOD_DATA_NO_POST_INC, |
| 0x0000); |
| /* tx data pad skew - devaddr = 0x02, register = 0x05 */ |
| ksz9031_phy_extended_write(phydev, 0x02, |
| MII_KSZ9031_EXT_RGMII_TX_DATA_SKEW, |
| MII_KSZ9031_MOD_DATA_NO_POST_INC, |
| 0x0000); |
| /* gtx and rx clock pad skew - devaddr = 0x02,register = 0x08 */ |
| ksz9031_phy_extended_write(phydev, 0x02, |
| MII_KSZ9031_EXT_RGMII_CLOCK_SKEW, |
| MII_KSZ9031_MOD_DATA_NO_POST_INC, |
| 0x03FF); |
| break; |
| } |
| |
| return 0; |
| } |
| |
| iomux_v3_cfg_t const enet_pads[] = { |
| MX6_PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL), |
| MX6_PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL), |
| MX6_PAD_RGMII_TXC__RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL), |
| MX6_PAD_RGMII_TD0__RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL), |
| MX6_PAD_RGMII_TD1__RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL), |
| MX6_PAD_RGMII_TD2__RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL), |
| MX6_PAD_RGMII_TD3__RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL), |
| MX6_PAD_RGMII_TX_CTL__RGMII_TX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL), |
| MX6_PAD_ENET_REF_CLK__ENET_TX_CLK | MUX_PAD_CTRL(ENET_PAD_CTRL), |
| MX6_PAD_RGMII_RXC__RGMII_RXC | MUX_PAD_CTRL(ENET_PAD_CTRL), |
| MX6_PAD_RGMII_RD0__RGMII_RD0 | MUX_PAD_CTRL(ENET_PAD_CTRL), |
| MX6_PAD_RGMII_RD1__RGMII_RD1 | MUX_PAD_CTRL(ENET_PAD_CTRL), |
| MX6_PAD_RGMII_RD2__RGMII_RD2 | MUX_PAD_CTRL(ENET_PAD_CTRL), |
| MX6_PAD_RGMII_RD3__RGMII_RD3 | MUX_PAD_CTRL(ENET_PAD_CTRL), |
| MX6_PAD_RGMII_RX_CTL__RGMII_RX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL), |
| /* KSZ9031 PHY Reset */ |
| MX6_PAD_ENET_CRS_DV__GPIO1_IO25 | MUX_PAD_CTRL(NO_PAD_CTRL) | |
| MUX_MODE_SION, |
| # define GPIO_ENET_PHY_RESET IMX_GPIO_NR(1, 25) |
| }; |
| |
| /* mux the Apalis GPIO pins, so they can be used from the U-Boot cmdline */ |
| iomux_v3_cfg_t const gpio_pads[] = { |
| /* Apalis GPIO1 - GPIO8 */ |
| MX6_PAD_NANDF_D4__GPIO2_IO04 | MUX_PAD_CTRL(WEAK_PULLUP) | |
| MUX_MODE_SION, |
| MX6_PAD_NANDF_D5__GPIO2_IO05 | MUX_PAD_CTRL(WEAK_PULLUP) | |
| MUX_MODE_SION, |
| MX6_PAD_NANDF_D6__GPIO2_IO06 | MUX_PAD_CTRL(WEAK_PULLUP) | |
| MUX_MODE_SION, |
| MX6_PAD_NANDF_D7__GPIO2_IO07 | MUX_PAD_CTRL(WEAK_PULLUP) | |
| MUX_MODE_SION, |
| MX6_PAD_NANDF_RB0__GPIO6_IO10 | MUX_PAD_CTRL(WEAK_PULLUP) | |
| MUX_MODE_SION, |
| MX6_PAD_NANDF_WP_B__GPIO6_IO09 | MUX_PAD_CTRL(WEAK_PULLUP) | |
| MUX_MODE_SION, |
| MX6_PAD_GPIO_2__GPIO1_IO02 | MUX_PAD_CTRL(WEAK_PULLDOWN) | |
| MUX_MODE_SION, |
| MX6_PAD_GPIO_6__GPIO1_IO06 | MUX_PAD_CTRL(WEAK_PULLUP) | |
| MUX_MODE_SION, |
| MX6_PAD_GPIO_4__GPIO1_IO04 | MUX_PAD_CTRL(WEAK_PULLUP) | |
| MUX_MODE_SION, |
| }; |
| |
| static void setup_iomux_gpio(void) |
| { |
| imx_iomux_v3_setup_multiple_pads(gpio_pads, ARRAY_SIZE(gpio_pads)); |
| } |
| |
| iomux_v3_cfg_t const usb_pads[] = { |
| /* USBH_EN */ |
| MX6_PAD_GPIO_0__GPIO1_IO00 | MUX_PAD_CTRL(NO_PAD_CTRL) | MUX_MODE_SION, |
| # define GPIO_USBH_EN IMX_GPIO_NR(1, 0) |
| /* USB_VBUS_DET */ |
| MX6_PAD_EIM_D28__GPIO3_IO28 | MUX_PAD_CTRL(NO_PAD_CTRL), |
| # define GPIO_USB_VBUS_DET IMX_GPIO_NR(3, 28) |
| /* USBO1_ID */ |
| MX6_PAD_ENET_RX_ER__USB_OTG_ID | MUX_PAD_CTRL(WEAK_PULLUP), |
| /* USBO1_EN */ |
| MX6_PAD_EIM_D22__GPIO3_IO22 | MUX_PAD_CTRL(NO_PAD_CTRL) | MUX_MODE_SION, |
| # define GPIO_USBO_EN IMX_GPIO_NR(3, 22) |
| }; |
| |
| /* |
| * UARTs are used in DTE mode, switch the mode on all UARTs before |
| * any pinmuxing connects a (DCE) output to a transceiver output. |
| */ |
| #define UCR3 0x88 /* FIFO Control Register */ |
| #define UCR3_RI BIT(8) /* RIDELT DTE mode */ |
| #define UCR3_DCD BIT(9) /* DCDDELT DTE mode */ |
| #define UFCR 0x90 /* FIFO Control Register */ |
| #define UFCR_DCEDTE BIT(6) /* DCE=0 */ |
| |
| static void setup_dtemode_uart(void) |
| { |
| setbits_le32((u32 *)(UART1_BASE + UFCR), UFCR_DCEDTE); |
| setbits_le32((u32 *)(UART2_BASE + UFCR), UFCR_DCEDTE); |
| setbits_le32((u32 *)(UART4_BASE + UFCR), UFCR_DCEDTE); |
| setbits_le32((u32 *)(UART5_BASE + UFCR), UFCR_DCEDTE); |
| |
| clrbits_le32((u32 *)(UART1_BASE + UCR3), UCR3_DCD | UCR3_RI); |
| clrbits_le32((u32 *)(UART2_BASE + UCR3), UCR3_DCD | UCR3_RI); |
| clrbits_le32((u32 *)(UART4_BASE + UCR3), UCR3_DCD | UCR3_RI); |
| clrbits_le32((u32 *)(UART5_BASE + UCR3), UCR3_DCD | UCR3_RI); |
| } |
| |
| static void setup_iomux_dte_uart(void) |
| { |
| setup_dtemode_uart(); |
| imx_iomux_v3_setup_multiple_pads(uart1_pads_dte, |
| ARRAY_SIZE(uart1_pads_dte)); |
| } |
| |
| #ifdef CONFIG_USB_EHCI_MX6 |
| int board_ehci_hcd_init(int port) |
| { |
| imx_iomux_v3_setup_multiple_pads(usb_pads, ARRAY_SIZE(usb_pads)); |
| return 0; |
| } |
| #endif |
| |
| #if defined(CONFIG_FSL_ESDHC_IMX) && defined(CONFIG_SPL_BUILD) |
| /* use the following sequence: eMMC, MMC1, SD1 */ |
| struct fsl_esdhc_cfg usdhc_cfg[CFG_SYS_FSL_USDHC_NUM] = { |
| {USDHC3_BASE_ADDR}, |
| {USDHC1_BASE_ADDR}, |
| {USDHC2_BASE_ADDR}, |
| }; |
| |
| int board_mmc_getcd(struct mmc *mmc) |
| { |
| struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv; |
| int ret = true; /* default: assume inserted */ |
| |
| switch (cfg->esdhc_base) { |
| case USDHC1_BASE_ADDR: |
| gpio_request(GPIO_MMC_CD, "MMC_CD"); |
| gpio_direction_input(GPIO_MMC_CD); |
| ret = !gpio_get_value(GPIO_MMC_CD); |
| break; |
| case USDHC2_BASE_ADDR: |
| gpio_request(GPIO_MMC_CD, "SD_CD"); |
| gpio_direction_input(GPIO_SD_CD); |
| ret = !gpio_get_value(GPIO_SD_CD); |
| break; |
| } |
| |
| return ret; |
| } |
| |
| int board_mmc_init(struct bd_info *bis) |
| { |
| struct src *psrc = (struct src *)SRC_BASE_ADDR; |
| unsigned reg = readl(&psrc->sbmr1) >> 11; |
| /* |
| * Upon reading BOOT_CFG register the following map is done: |
| * Bit 11 and 12 of BOOT_CFG register can determine the current |
| * mmc port |
| * 0x1 SD1 |
| * 0x2 SD2 |
| * 0x3 SD4 |
| */ |
| |
| switch (reg & 0x3) { |
| case 0x0: |
| imx_iomux_v3_setup_multiple_pads( |
| usdhc1_pads, ARRAY_SIZE(usdhc1_pads)); |
| usdhc_cfg[0].esdhc_base = USDHC1_BASE_ADDR; |
| usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK); |
| gd->arch.sdhc_clk = usdhc_cfg[0].sdhc_clk; |
| break; |
| case 0x1: |
| imx_iomux_v3_setup_multiple_pads( |
| usdhc2_pads, ARRAY_SIZE(usdhc2_pads)); |
| usdhc_cfg[0].esdhc_base = USDHC2_BASE_ADDR; |
| usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK); |
| gd->arch.sdhc_clk = usdhc_cfg[0].sdhc_clk; |
| break; |
| case 0x2: |
| imx_iomux_v3_setup_multiple_pads( |
| usdhc3_pads, ARRAY_SIZE(usdhc3_pads)); |
| usdhc_cfg[0].esdhc_base = USDHC3_BASE_ADDR; |
| usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK); |
| gd->arch.sdhc_clk = usdhc_cfg[0].sdhc_clk; |
| break; |
| default: |
| puts("MMC boot device not available"); |
| } |
| |
| return fsl_esdhc_initialize(bis, &usdhc_cfg[0]); |
| } |
| #endif /* CONFIG_FSL_ESDHC_IMX & CONFIG_SPL_BUILD */ |
| |
| int board_phy_config(struct phy_device *phydev) |
| { |
| mx6_rgmii_rework(phydev); |
| if (phydev->drv->config) |
| phydev->drv->config(phydev); |
| |
| return 0; |
| } |
| |
| static iomux_v3_cfg_t const pwr_intb_pads[] = { |
| /* |
| * the bootrom sets the iomux to vselect, potentially connecting |
| * two outputs. Set this back to GPIO |
| */ |
| MX6_PAD_GPIO_18__GPIO7_IO13 | MUX_PAD_CTRL(NO_PAD_CTRL) |
| }; |
| |
| #if defined(CONFIG_VIDEO_IPUV3) |
| |
| static iomux_v3_cfg_t const backlight_pads[] = { |
| /* Backlight on RGB connector: J15 */ |
| MX6_PAD_EIM_DA13__GPIO3_IO13 | MUX_PAD_CTRL(NO_PAD_CTRL) | |
| MUX_MODE_SION, |
| #define RGB_BACKLIGHT_GP IMX_GPIO_NR(3, 13) |
| /* additional CPU pin on BKL_PWM, keep in tristate */ |
| MX6_PAD_EIM_DA14__GPIO3_IO14 | MUX_PAD_CTRL(TRISTATE), |
| /* Backlight PWM, used as GPIO in U-Boot */ |
| MX6_PAD_SD4_DAT2__GPIO2_IO10 | MUX_PAD_CTRL(NO_PAD_CTRL) | |
| MUX_MODE_SION, |
| #define RGB_BACKLIGHTPWM_GP IMX_GPIO_NR(2, 10) |
| /* buffer output enable 0: buffer enabled */ |
| MX6_PAD_EIM_A25__GPIO5_IO02 | MUX_PAD_CTRL(WEAK_PULLUP) | MUX_MODE_SION, |
| #define RGB_BACKLIGHTPWM_OE IMX_GPIO_NR(5, 2) |
| /* PSAVE# integrated VDAC */ |
| MX6_PAD_EIM_BCLK__GPIO6_IO31 | MUX_PAD_CTRL(NO_PAD_CTRL) | |
| MUX_MODE_SION, |
| #define VGA_PSAVE_NOT_GP IMX_GPIO_NR(6, 31) |
| }; |
| |
| static iomux_v3_cfg_t const rgb_pads[] = { |
| MX6_PAD_EIM_A16__IPU1_DI1_DISP_CLK | MUX_PAD_CTRL(OUTPUT_RGB), |
| MX6_PAD_EIM_DA10__IPU1_DI1_PIN15 | MUX_PAD_CTRL(OUTPUT_RGB), |
| MX6_PAD_EIM_DA11__IPU1_DI1_PIN02 | MUX_PAD_CTRL(OUTPUT_RGB), |
| MX6_PAD_EIM_DA12__IPU1_DI1_PIN03 | MUX_PAD_CTRL(OUTPUT_RGB), |
| MX6_PAD_EIM_DA9__IPU1_DISP1_DATA00 | MUX_PAD_CTRL(OUTPUT_RGB), |
| MX6_PAD_EIM_DA8__IPU1_DISP1_DATA01 | MUX_PAD_CTRL(OUTPUT_RGB), |
| MX6_PAD_EIM_DA7__IPU1_DISP1_DATA02 | MUX_PAD_CTRL(OUTPUT_RGB), |
| MX6_PAD_EIM_DA6__IPU1_DISP1_DATA03 | MUX_PAD_CTRL(OUTPUT_RGB), |
| MX6_PAD_EIM_DA5__IPU1_DISP1_DATA04 | MUX_PAD_CTRL(OUTPUT_RGB), |
| MX6_PAD_EIM_DA4__IPU1_DISP1_DATA05 | MUX_PAD_CTRL(OUTPUT_RGB), |
| MX6_PAD_EIM_DA3__IPU1_DISP1_DATA06 | MUX_PAD_CTRL(OUTPUT_RGB), |
| MX6_PAD_EIM_DA2__IPU1_DISP1_DATA07 | MUX_PAD_CTRL(OUTPUT_RGB), |
| MX6_PAD_EIM_DA1__IPU1_DISP1_DATA08 | MUX_PAD_CTRL(OUTPUT_RGB), |
| MX6_PAD_EIM_DA0__IPU1_DISP1_DATA09 | MUX_PAD_CTRL(OUTPUT_RGB), |
| MX6_PAD_EIM_EB1__IPU1_DISP1_DATA10 | MUX_PAD_CTRL(OUTPUT_RGB), |
| MX6_PAD_EIM_EB0__IPU1_DISP1_DATA11 | MUX_PAD_CTRL(OUTPUT_RGB), |
| MX6_PAD_EIM_A17__IPU1_DISP1_DATA12 | MUX_PAD_CTRL(OUTPUT_RGB), |
| MX6_PAD_EIM_A18__IPU1_DISP1_DATA13 | MUX_PAD_CTRL(OUTPUT_RGB), |
| MX6_PAD_EIM_A19__IPU1_DISP1_DATA14 | MUX_PAD_CTRL(OUTPUT_RGB), |
| MX6_PAD_EIM_A20__IPU1_DISP1_DATA15 | MUX_PAD_CTRL(OUTPUT_RGB), |
| MX6_PAD_EIM_A21__IPU1_DISP1_DATA16 | MUX_PAD_CTRL(OUTPUT_RGB), |
| MX6_PAD_EIM_A22__IPU1_DISP1_DATA17 | MUX_PAD_CTRL(OUTPUT_RGB), |
| MX6_PAD_EIM_A23__IPU1_DISP1_DATA18 | MUX_PAD_CTRL(OUTPUT_RGB), |
| MX6_PAD_EIM_A24__IPU1_DISP1_DATA19 | MUX_PAD_CTRL(OUTPUT_RGB), |
| MX6_PAD_EIM_D26__IPU1_DISP1_DATA22 | MUX_PAD_CTRL(OUTPUT_RGB), |
| MX6_PAD_EIM_D27__IPU1_DISP1_DATA23 | MUX_PAD_CTRL(OUTPUT_RGB), |
| MX6_PAD_EIM_D30__IPU1_DISP1_DATA21 | MUX_PAD_CTRL(OUTPUT_RGB), |
| MX6_PAD_EIM_D31__IPU1_DISP1_DATA20 | MUX_PAD_CTRL(OUTPUT_RGB), |
| }; |
| |
| static void do_enable_hdmi(struct display_info_t const *dev) |
| { |
| imx_enable_hdmi_phy(); |
| } |
| |
| static void enable_lvds(struct display_info_t const *dev) |
| { |
| struct iomuxc *iomux = (struct iomuxc *) |
| IOMUXC_BASE_ADDR; |
| u32 reg = readl(&iomux->gpr[2]); |
| reg |= IOMUXC_GPR2_DATA_WIDTH_CH0_24BIT; |
| writel(reg, &iomux->gpr[2]); |
| gpio_direction_output(RGB_BACKLIGHT_GP, 1); |
| gpio_direction_output(RGB_BACKLIGHTPWM_GP, 0); |
| gpio_direction_output(RGB_BACKLIGHTPWM_OE, 0); |
| } |
| |
| static void enable_rgb(struct display_info_t const *dev) |
| { |
| imx_iomux_v3_setup_multiple_pads( |
| rgb_pads, |
| ARRAY_SIZE(rgb_pads)); |
| gpio_direction_output(RGB_BACKLIGHT_GP, 1); |
| gpio_direction_output(RGB_BACKLIGHTPWM_GP, 0); |
| gpio_direction_output(RGB_BACKLIGHTPWM_OE, 0); |
| } |
| |
| static int detect_default(struct display_info_t const *dev) |
| { |
| (void) dev; |
| return 1; |
| } |
| |
| struct display_info_t const displays[] = {{ |
| .bus = -1, |
| .addr = 0, |
| .pixfmt = IPU_PIX_FMT_RGB24, |
| .detect = detect_hdmi, |
| .enable = do_enable_hdmi, |
| .mode = { |
| .name = "HDMI", |
| .refresh = 60, |
| .xres = 1024, |
| .yres = 768, |
| .pixclock = 15385, |
| .left_margin = 220, |
| .right_margin = 40, |
| .upper_margin = 21, |
| .lower_margin = 7, |
| .hsync_len = 60, |
| .vsync_len = 10, |
| .sync = FB_SYNC_EXT, |
| .vmode = FB_VMODE_NONINTERLACED |
| } }, { |
| .bus = -1, |
| .addr = 0, |
| .di = 1, |
| .pixfmt = IPU_PIX_FMT_RGB24, |
| .detect = detect_default, |
| .enable = enable_rgb, |
| .mode = { |
| .name = "vga-rgb", |
| .refresh = 60, |
| .xres = 640, |
| .yres = 480, |
| .pixclock = 33000, |
| .left_margin = 48, |
| .right_margin = 16, |
| .upper_margin = 31, |
| .lower_margin = 11, |
| .hsync_len = 96, |
| .vsync_len = 2, |
| .sync = 0, |
| .vmode = FB_VMODE_NONINTERLACED |
| } }, { |
| .bus = -1, |
| .addr = 0, |
| .di = 1, |
| .pixfmt = IPU_PIX_FMT_RGB24, |
| .enable = enable_rgb, |
| .mode = { |
| .name = "wvga-rgb", |
| .refresh = 60, |
| .xres = 800, |
| .yres = 480, |
| .pixclock = 25000, |
| .left_margin = 40, |
| .right_margin = 88, |
| .upper_margin = 33, |
| .lower_margin = 10, |
| .hsync_len = 128, |
| .vsync_len = 2, |
| .sync = 0, |
| .vmode = FB_VMODE_NONINTERLACED |
| } }, { |
| .bus = -1, |
| .addr = 0, |
| .pixfmt = IPU_PIX_FMT_LVDS666, |
| .enable = enable_lvds, |
| .mode = { |
| .name = "wsvga-lvds", |
| .refresh = 60, |
| .xres = 1024, |
| .yres = 600, |
| .pixclock = 15385, |
| .left_margin = 220, |
| .right_margin = 40, |
| .upper_margin = 21, |
| .lower_margin = 7, |
| .hsync_len = 60, |
| .vsync_len = 10, |
| .sync = FB_SYNC_EXT, |
| .vmode = FB_VMODE_NONINTERLACED |
| } } }; |
| size_t display_count = ARRAY_SIZE(displays); |
| |
| static void setup_display(void) |
| { |
| struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR; |
| struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR; |
| int reg; |
| |
| enable_ipu_clock(); |
| imx_setup_hdmi(); |
| /* Turn on LDB0,IPU,IPU DI0 clocks */ |
| reg = __raw_readl(&mxc_ccm->CCGR3); |
| reg |= MXC_CCM_CCGR3_LDB_DI0_MASK; |
| writel(reg, &mxc_ccm->CCGR3); |
| |
| /* set LDB0, LDB1 clk select to 011/011 */ |
| reg = readl(&mxc_ccm->cs2cdr); |
| reg &= ~(MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_MASK |
| |MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_MASK); |
| reg |= (3<<MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_OFFSET) |
| |(3<<MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_OFFSET); |
| writel(reg, &mxc_ccm->cs2cdr); |
| |
| reg = readl(&mxc_ccm->cscmr2); |
| reg |= MXC_CCM_CSCMR2_LDB_DI0_IPU_DIV; |
| writel(reg, &mxc_ccm->cscmr2); |
| |
| reg = readl(&mxc_ccm->chsccdr); |
| reg |= (CHSCCDR_CLK_SEL_LDB_DI0 |
| <<MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET); |
| writel(reg, &mxc_ccm->chsccdr); |
| |
| reg = IOMUXC_GPR2_BGREF_RRMODE_EXTERNAL_RES |
| |IOMUXC_GPR2_DI1_VS_POLARITY_ACTIVE_HIGH |
| |IOMUXC_GPR2_DI0_VS_POLARITY_ACTIVE_LOW |
| |IOMUXC_GPR2_BIT_MAPPING_CH1_SPWG |
| |IOMUXC_GPR2_DATA_WIDTH_CH1_18BIT |
| |IOMUXC_GPR2_BIT_MAPPING_CH0_SPWG |
| |IOMUXC_GPR2_DATA_WIDTH_CH0_18BIT |
| |IOMUXC_GPR2_LVDS_CH1_MODE_DISABLED |
| |IOMUXC_GPR2_LVDS_CH0_MODE_ENABLED_DI0; |
| writel(reg, &iomux->gpr[2]); |
| |
| reg = readl(&iomux->gpr[3]); |
| reg = (reg & ~(IOMUXC_GPR3_LVDS0_MUX_CTL_MASK |
| |IOMUXC_GPR3_HDMI_MUX_CTL_MASK)) |
| | (IOMUXC_GPR3_MUX_SRC_IPU1_DI0 |
| <<IOMUXC_GPR3_LVDS0_MUX_CTL_OFFSET); |
| writel(reg, &iomux->gpr[3]); |
| |
| /* backlight unconditionally on for now */ |
| imx_iomux_v3_setup_multiple_pads(backlight_pads, |
| ARRAY_SIZE(backlight_pads)); |
| /* use 0 for EDT 7", use 1 for LG fullHD panel */ |
| gpio_request(RGB_BACKLIGHTPWM_GP, "BKL1_PWM"); |
| gpio_request(RGB_BACKLIGHTPWM_OE, "BKL1_PWM_EN"); |
| gpio_request(RGB_BACKLIGHT_GP, "BKL1_ON"); |
| gpio_direction_output(RGB_BACKLIGHTPWM_GP, 0); |
| gpio_direction_output(RGB_BACKLIGHTPWM_OE, 0); |
| gpio_direction_output(RGB_BACKLIGHT_GP, 1); |
| } |
| |
| /* |
| * Backlight off before OS handover |
| */ |
| void board_preboot_os(void) |
| { |
| gpio_direction_output(RGB_BACKLIGHTPWM_GP, 1); |
| gpio_direction_output(RGB_BACKLIGHT_GP, 0); |
| } |
| #endif /* defined(CONFIG_VIDEO_IPUV3) */ |
| |
| int board_early_init_f(void) |
| { |
| imx_iomux_v3_setup_multiple_pads(pwr_intb_pads, |
| ARRAY_SIZE(pwr_intb_pads)); |
| setup_iomux_dte_uart(); |
| |
| return 0; |
| } |
| |
| /* |
| * Do not overwrite the console |
| * Use always serial for U-Boot console |
| */ |
| int overwrite_console(void) |
| { |
| return 1; |
| } |
| |
| int board_init(void) |
| { |
| /* address of boot parameters */ |
| gd->bd->bi_boot_params = PHYS_SDRAM + 0x100; |
| |
| #if defined(CONFIG_VIDEO_IPUV3) |
| setup_display(); |
| #endif |
| |
| #ifdef CONFIG_TDX_CMD_IMX_MFGR |
| (void) pmic_init(); |
| #endif |
| |
| #ifdef CONFIG_SATA |
| setup_sata(); |
| #endif |
| |
| setup_iomux_gpio(); |
| |
| return 0; |
| } |
| |
| #ifdef CONFIG_BOARD_LATE_INIT |
| int board_late_init(void) |
| { |
| #if defined(CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG) |
| char env_str[256]; |
| u32 rev; |
| |
| rev = get_board_revision(); |
| snprintf(env_str, ARRAY_SIZE(env_str), "%.4x", rev); |
| env_set("board_rev", env_str); |
| #endif /* CONFIG_BOARD_LATE_INIT */ |
| |
| if (IS_ENABLED(CONFIG_USB) && is_boot_from_usb()) { |
| env_set("bootdelay", "0"); |
| if (IS_ENABLED(CONFIG_CMD_USB_SDP)) { |
| printf("Serial Downloader recovery mode, using sdp command\n"); |
| env_set("bootcmd", "sdp 0"); |
| } else if (IS_ENABLED(CONFIG_CMD_FASTBOOT)) { |
| printf("Fastboot recovery mode, using fastboot command\n"); |
| env_set("bootcmd", "fastboot usb 0"); |
| } |
| } |
| |
| return 0; |
| } |
| #endif /* CONFIG_BOARD_LATE_INIT */ |
| |
| #if defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP) |
| int ft_board_setup(void *blob, struct bd_info *bd) |
| { |
| return ft_common_board_setup(blob, bd); |
| } |
| #endif |
| |
| #ifdef CONFIG_CMD_BMODE |
| static const struct boot_mode board_boot_modes[] = { |
| /* 4-bit bus width */ |
| {"mmc", MAKE_CFGVAL(0x40, 0x20, 0x00, 0x00)}, |
| {"sd", MAKE_CFGVAL(0x40, 0x28, 0x00, 0x00)}, |
| {NULL, 0}, |
| }; |
| #endif |
| |
| int misc_init_r(void) |
| { |
| #ifdef CONFIG_CMD_BMODE |
| add_board_boot_modes(board_boot_modes); |
| #endif |
| return 0; |
| } |
| |
| #ifdef CONFIG_LDO_BYPASS_CHECK |
| /* TODO, use external pmic, for now always ldo_enable */ |
| void ldo_mode_set(int ldo_bypass) |
| { |
| return; |
| } |
| #endif |
| |
| #ifdef CONFIG_SPL_BUILD |
| #include <spl.h> |
| #include <linux/libfdt.h> |
| #include "asm/arch/mx6q-ddr.h" |
| #include "asm/arch/iomux.h" |
| #include "asm/arch/crm_regs.h" |
| |
| static void ccgr_init(void) |
| { |
| struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR; |
| |
| writel(0x00C03F3F, &ccm->CCGR0); |
| writel(0x0030FC03, &ccm->CCGR1); |
| writel(0x0FFFFFF3, &ccm->CCGR2); |
| writel(0x3FF0300F, &ccm->CCGR3); |
| writel(0x00FFF300, &ccm->CCGR4); |
| writel(0x0F0000F3, &ccm->CCGR5); |
| writel(0x000003FF, &ccm->CCGR6); |
| |
| /* |
| * Setup CCM_CCOSR register as follows: |
| * |
| * clko2_en = 1 --> CKO2 enabled |
| * clko2_div = 000 --> divide by 1 |
| * clko2_sel = 01110 --> osc_clk (24MHz) |
| * |
| * clk_out_sel = 1 --> Output CKO2 to CKO1 |
| * |
| * This sets both CLKO2/CLKO1 output to 24MHz, |
| * CLKO1 configuration not relevant because of clk_out_sel |
| * (CLKO1 set to default) |
| */ |
| writel(0x010E0101, &ccm->ccosr); |
| } |
| |
| |
| #define PAD_CTL_INPUT_DDR BIT(17) |
| |
| struct mx6dq_iomux_ddr_regs mx6_ddr_ioregs = { |
| /* Differential input, 40 ohm DSE */ |
| .dram_sdclk_0 = PAD_CTL_DSE_40ohm | PAD_CTL_INPUT_DDR, |
| .dram_sdclk_1 = PAD_CTL_DSE_40ohm | PAD_CTL_INPUT_DDR, |
| .dram_cas = PAD_CTL_DSE_40ohm | PAD_CTL_INPUT_DDR, |
| .dram_ras = PAD_CTL_DSE_40ohm | PAD_CTL_INPUT_DDR, |
| .dram_reset = PAD_CTL_DSE_40ohm | PAD_CTL_INPUT_DDR, |
| |
| /* SDKE[0:1]: BIT(12) and BIT(13) are reserved and set at reset */ |
| .dram_sdcke0 = 0x00003000, |
| .dram_sdcke1 = 0x00003000, |
| |
| .dram_sdba2 = 0x00000000, |
| |
| /* ODT[0:1]: 40 ohm DSE, BIT(12) and BIT(13) are reserved and set at reset */ |
| .dram_sdodt0 = PAD_CTL_DSE_40ohm | 0x00003000, |
| .dram_sdodt1 = PAD_CTL_DSE_40ohm | 0x00003000, |
| |
| /* SDQS[0:7]: 40 ohm DSE, Pull/Keeper Disabled, ODT Disabled */ |
| .dram_sdqs0 = PAD_CTL_DSE_40ohm, |
| .dram_sdqs1 = PAD_CTL_DSE_40ohm, |
| .dram_sdqs2 = PAD_CTL_DSE_40ohm, |
| .dram_sdqs3 = PAD_CTL_DSE_40ohm, |
| .dram_sdqs4 = PAD_CTL_DSE_40ohm, |
| .dram_sdqs5 = PAD_CTL_DSE_40ohm, |
| .dram_sdqs6 = PAD_CTL_DSE_40ohm, |
| .dram_sdqs7 = PAD_CTL_DSE_40ohm, |
| |
| /* DQM[0:7]: Differential input, 40 ohm DSE, Pull/Keeper Disabled, ODT Disabled */ |
| .dram_dqm0 = PAD_CTL_DSE_40ohm | PAD_CTL_INPUT_DDR, |
| .dram_dqm1 = PAD_CTL_DSE_40ohm | PAD_CTL_INPUT_DDR, |
| .dram_dqm2 = PAD_CTL_DSE_40ohm | PAD_CTL_INPUT_DDR, |
| .dram_dqm3 = PAD_CTL_DSE_40ohm | PAD_CTL_INPUT_DDR, |
| .dram_dqm4 = PAD_CTL_DSE_40ohm | PAD_CTL_INPUT_DDR, |
| .dram_dqm5 = PAD_CTL_DSE_40ohm | PAD_CTL_INPUT_DDR, |
| .dram_dqm6 = PAD_CTL_DSE_40ohm | PAD_CTL_INPUT_DDR, |
| .dram_dqm7 = PAD_CTL_DSE_40ohm | PAD_CTL_INPUT_DDR, |
| }; |
| |
| struct mx6dq_iomux_grp_regs mx6_grp_ioregs = { |
| /* DDR3 */ |
| .grp_ddr_type = 0x000C0000, |
| |
| /* SDQS[0:7]: Differential input */ |
| .grp_ddrmode_ctl = PAD_CTL_INPUT_DDR, |
| |
| /* DATA[0:63]: Pull/Keeper disabled */ |
| .grp_ddrpke = 0, |
| |
| /* ADDR[0:16], SDBA[0:1]: 40 ohm DSE */ |
| .grp_addds = PAD_CTL_DSE_40ohm, |
| |
| /* CS0/CS1/SDBA2/CKE0/CKE1/SDWE: 40 ohm DSE */ |
| .grp_ctlds = PAD_CTL_DSE_40ohm, |
| |
| /* DATA[0:63]: Differential input */ |
| .grp_ddrmode = PAD_CTL_INPUT_DDR, |
| |
| /* DATA[0:63]: 40 ohm DSE */ |
| .grp_b0ds = PAD_CTL_DSE_40ohm, |
| .grp_b1ds = PAD_CTL_DSE_40ohm, |
| .grp_b2ds = PAD_CTL_DSE_40ohm, |
| .grp_b3ds = PAD_CTL_DSE_40ohm, |
| .grp_b4ds = PAD_CTL_DSE_40ohm, |
| .grp_b5ds = PAD_CTL_DSE_40ohm, |
| .grp_b6ds = PAD_CTL_DSE_40ohm, |
| .grp_b7ds = PAD_CTL_DSE_40ohm, |
| }; |
| |
| struct mx6_ddr_sysinfo sysinfo = { |
| .dsize = 2, /* width of data bus: 2=64 */ |
| .cs_density = 32, /* full range so that get_mem_size() works, 32Gb per CS */ |
| .ncs = 1, |
| .cs1_mirror = 0, |
| .rtt_wr = 2, /* Dynamic ODT, RZQ/2 */ |
| .rtt_nom = 0, /* Disabled */ |
| .walat = 0, /* Write additional latency */ |
| .ralat = 5, /* Read additional latency */ |
| .mif3_mode = 3, /* Command prediction working mode */ |
| .bi_on = 1, /* Bank interleaving enabled */ |
| .sde_to_rst = 0x10, /* 14 cycles, 200us (JEDEC default) */ |
| .rst_to_cke = 0x23, /* 33 cycles, 500us (JEDEC default) */ |
| .pd_fast_exit = 1, /* enable precharge power-down fast exit */ |
| .ddr_type = DDR_TYPE_DDR3, |
| .refsel = 1, /* Refresh cycles at 32KHz */ |
| .refr = 3, /* 4 refresh commands per refresh cycle */ |
| }; |
| |
| static const struct mx6_mmdc_calibration mx6_mmdc_calib = { |
| .p0_mpwldectrl0 = 0x0009000E, |
| .p0_mpwldectrl1 = 0x0018000B, |
| .p1_mpwldectrl0 = 0x00060015, |
| .p1_mpwldectrl1 = 0x0006000E, |
| .p0_mpdgctrl0 = 0x432A0338, |
| .p0_mpdgctrl1 = 0x03260324, |
| .p1_mpdgctrl0 = 0x43340344, |
| .p1_mpdgctrl1 = 0x031E027C, |
| .p0_mprddlctl = 0x33272D2E, |
| .p1_mprddlctl = 0x2F312B37, |
| .p0_mpwrdlctl = 0x3A35433C, |
| .p1_mpwrdlctl = 0x4336453F, |
| }; |
| |
| static const struct mx6_ddr3_cfg ddr3_cfg = { |
| .mem_speed = 1066, |
| .density = 2, |
| .width = 16, |
| .banks = 8, |
| .rowaddr = 14, |
| .coladdr = 10, |
| .pagesz = 2, |
| .trcd = 1312, |
| .trcmin = 4812, |
| .trasmin = 3500, |
| .SRT = 0, |
| }; |
| |
| struct mx6_ddr_sysinfo sysinfo_it = { |
| .dsize = 2, /* width of data bus: 2=64 */ |
| .cs_density = 32, /* full range so that get_mem_size() works, 32Gb per CS */ |
| .ncs = 1, |
| .cs1_mirror = 0, |
| .rtt_wr = 1, /* Dynamic ODT, RZQ/4 */ |
| .rtt_nom = 1, /* RZQ/4 */ |
| .walat = 0, /* Write additional latency */ |
| .ralat = 5, /* Read additional latency */ |
| .mif3_mode = 3, /* Command prediction working mode */ |
| .bi_on = 1, /* Bank interleaving enabled */ |
| .sde_to_rst = 0x10, /* 14 cycles, 200us (JEDEC default) */ |
| .rst_to_cke = 0x23, /* 33 cycles, 500us (JEDEC default) */ |
| .pd_fast_exit = 1, /* enable precharge power-down fast exit */ |
| .ddr_type = DDR_TYPE_DDR3, |
| .refsel = 1, /* Refresh cycles at 32KHz */ |
| .refr = 7, /* 8 refresh commands per refresh cycle */ |
| }; |
| |
| static const struct mx6_mmdc_calibration mx6_mmdc_calib_it = { |
| .p0_mpwldectrl0 = 0x0009000E, |
| .p0_mpwldectrl1 = 0x0018000B, |
| .p1_mpwldectrl0 = 0x00060015, |
| .p1_mpwldectrl1 = 0x0006000E, |
| .p0_mpdgctrl0 = 0x03300338, |
| .p0_mpdgctrl1 = 0x03240324, |
| .p1_mpdgctrl0 = 0x03440350, |
| .p1_mpdgctrl1 = 0x032C0308, |
| .p0_mprddlctl = 0x40363C3E, |
| .p1_mprddlctl = 0x3C3E3C46, |
| .p0_mpwrdlctl = 0x403E463E, |
| .p1_mpwrdlctl = 0x4A384C46, |
| }; |
| |
| static const struct mx6_ddr3_cfg ddr3_cfg_it = { |
| .mem_speed = 1066, |
| .density = 4, |
| .width = 16, |
| .banks = 8, |
| .rowaddr = 15, |
| .coladdr = 10, |
| .pagesz = 2, |
| .trcd = 1312, |
| .trcmin = 4812, |
| .trasmin = 3500, |
| .SRT = 1, |
| }; |
| |
| |
| /* Perform DDR DRAM calibration */ |
| static void spl_dram_perform_cal(const struct mx6_ddr_sysinfo *ddr_sysinfo) |
| { |
| #ifdef CONFIG_MX6_DDRCAL |
| int err; |
| |
| err = mmdc_do_write_level_calibration(ddr_sysinfo); |
| if (err) |
| printf("error %d from write level calibration\n", err); |
| err = mmdc_do_dqs_calibration(ddr_sysinfo); |
| if (err) |
| printf("error %d from dqs calibration\n", err); |
| #endif |
| } |
| |
| static void spl_dram_init(void) |
| { |
| bool temp_grade_it; |
| |
| switch (get_cpu_temp_grade(NULL, NULL)) { |
| case TEMP_COMMERCIAL: |
| case TEMP_EXTCOMMERCIAL: |
| puts("Commercial temperature grade DDR3 timings.\n"); |
| temp_grade_it = false; |
| break; |
| case TEMP_INDUSTRIAL: |
| case TEMP_AUTOMOTIVE: |
| default: |
| puts("Industrial temperature grade DDR3 timings.\n"); |
| temp_grade_it = true; |
| break; |
| }; |
| |
| mx6dq_dram_iocfg(64, &mx6_ddr_ioregs, &mx6_grp_ioregs); |
| |
| if (temp_grade_it) |
| mx6_dram_cfg(&sysinfo_it, &mx6_mmdc_calib_it, &ddr3_cfg_it); |
| else |
| mx6_dram_cfg(&sysinfo, &mx6_mmdc_calib, &ddr3_cfg); |
| |
| udelay(100); |
| |
| if (temp_grade_it) |
| spl_dram_perform_cal(&sysinfo_it); |
| else |
| spl_dram_perform_cal(&sysinfo); |
| } |
| |
| void board_init_f(ulong dummy) |
| { |
| /* setup AIPS and disable watchdog */ |
| arch_cpu_init(); |
| |
| ccgr_init(); |
| gpr_init(); |
| |
| /* iomux */ |
| board_early_init_f(); |
| |
| /* setup GP timer */ |
| timer_init(); |
| |
| /* UART clocks enabled and gd valid - init serial console */ |
| preloader_console_init(); |
| |
| /* Make sure we use dte mode */ |
| setup_dtemode_uart(); |
| |
| /* DDR initialization */ |
| spl_dram_init(); |
| |
| /* Clear the BSS. */ |
| memset(__bss_start, 0, __bss_end - __bss_start); |
| |
| /* load/boot image from boot device */ |
| board_init_r(NULL, 0); |
| } |
| |
| #ifdef CONFIG_SPL_LOAD_FIT |
| int board_fit_config_name_match(const char *name) |
| { |
| if (!strcmp(name, "imx6-apalis")) |
| return 0; |
| |
| return -1; |
| } |
| #endif |
| |
| void reset_cpu(void) |
| { |
| } |
| |
| #endif /* CONFIG_SPL_BUILD */ |
| |
| static struct mxc_serial_plat mxc_serial_plat = { |
| .reg = (struct mxc_uart *)UART1_BASE, |
| .use_dte = true, |
| }; |
| |
| U_BOOT_DRVINFO(mxc_serial) = { |
| .name = "serial_mxc", |
| .plat = &mxc_serial_plat, |
| }; |