include/configs/CCM.h - filogic/uboot - Gitiles

 /*
  * (C) Copyright 2001-2005
  * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
  *
  * See file CREDITS for list of people who contributed to this
  * project.
  *
  * This program is free software; you can redistribute it and/or
  * modify it under the terms of the GNU General Public License as
  * published by the Free Software Foundation; either version 2 of
  * the License, or (at your option) any later version.
  *
  * This program is distributed in the hope that it will be useful,
  * but WITHOUT ANY WARRANTY; without even the implied warranty of
  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  * GNU General Public License for more details.
  *
  * You should have received a copy of the GNU General Public License
  * along with this program; if not, write to the Free Software
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
  * MA 02111-1307 USA
  */

 /*
  * configuration options, board specific, for Siemens Card Controller Module
  */

 #ifndef __CONFIG_H
 #define __CONFIG_H

 #undef	CCM_80MHz			/* define for 80 MHz CPU only */

 /*
  * High Level Configuration Options
  * (easy to change)
  */

 #define CONFIG_MPC860           1   /* This is a MPC860 CPU ... */
 #define CONFIG_CCM              1   /* on a Card Controller Module  */

 #define CONFIG_8xx_CONS_SMC1    1   /* Console is on SMC1       */
 #undef  CONFIG_8xx_CONS_SMC2
 #undef  CONFIG_8xx_CONS_NONE

 /*  ENVIRONMENT */

 #define CONFIG_BAUDRATE         19200         /* console baudrate in bps    */
 #define CONFIG_BOOTDELAY        2             /* autoboot after 2 seconds   */

 #define CONFIG_IPADDR           192.168.0.42
 #define CONFIG_NETMASK          255.255.255.0
 #define CONFIG_GATEWAYIP        0.0.0.0
 #define CONFIG_SERVERIP         192.168.0.254

 #define CONFIG_HOSTNAME         CCM

 #define CONFIG_LOADADDR         40180000

 #undef	CONFIG_BOOTARGS

 #define CONFIG_BOOTCOMMAND      "setenv bootargs " \
 				"mem=${mem} " \
 				"root=/dev/ram rw ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off " \
 				"wt_8xx=timeout:3600; " \
 				"bootm"

 #define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
 #undef	CFG_LOADS_BAUD_CHANGE	/* don't allow baudrate change	*/

 #define	CONFIG_WATCHDOG		1	/* watchdog enabled		*/

 #undef	CONFIG_STATUS_LED		/* Status LED disabled		*/

 #define	CONFIG_PRAM		512	/* reserve 512kB "protected RAM"*/

 #define	CONFIG_RTC_MPC8xx		/* use internal RTC of MPC8xx	*/

 #define	CONFIG_SPI			/* enable SPI driver		*/
 #define	CONFIG_SPI_X			/* 16 bit EEPROM addressing	*/

 /* ----------------------------------------------------------------
  * Offset to initial SPI buffers in DPRAM (used if the environment
  * is in the SPI EEPROM): We need a 520 byte scratch DPRAM area to
  * use at an early stage. It is used between the two initialization
  * calls (spi_init_f() and spi_init_r()). The value 0xB00 makes it
  * far enough from the start of the data area (as well as from the
  * stack pointer).
  * ---------------------------------------------------------------- */
 #define CFG_SPI_INIT_OFFSET		0xB00

 #define CFG_EEPROM_PAGE_WRITE_BITS	5	/* 32-byte page size	*/


 #define CONFIG_MAC_PARTITION		/* nod used yet			*/
 #define CONFIG_DOS_PARTITION

 #define CONFIG_BOOTP_MASK	(CONFIG_BOOTP_DEFAULT | CONFIG_BOOTP_BOOTFILESIZE)


 /*
  * Command line configuration.
  */
 #include <config_cmd_default.h>

 #define CONFIG_CMD_BSP
 #define CONFIG_CMD_DHCP
 #define CONFIG_CMD_DATE
 #define CONFIG_CMD_EEPROM
 #define CONFIG_CMD_NFS
 #define CONFIG_CMD_SNTP


 /*
  * Miscellaneous configurable options
  */
 #define	CFG_LONGHELP			/* undef to save memory		*/
 #define	CFG_PROMPT	"=> "		/* Monitor Command Prompt	*/
 #if defined(CONFIG_CMD_KGDB)
 #define	CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
 #else
 #define	CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
 #endif
 #define	CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
 #define	CFG_MAXARGS	16		/* max number of command args	*/
 #define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size	*/

 #define CFG_MEMTEST_START	0x00100000	/* memtest works on	*/
 #define CFG_MEMTEST_END		0x00F00000	/* 1 ... 15MB in DRAM	*/

 #define	CFG_LOAD_ADDR		0x00100000	/* default load address	*/

 /* Ethernet hardware configuration done using port pins */
 #define CFG_PA_ETH_RESET 	0x0200		/* PA  6	*/
 #define CFG_PA_ETH_MDDIS	0x4000		/* PA  1	*/
 #define CFG_PB_ETH_POWERDOWN	0x00000800	/* PB 20	*/
 #define CFG_PB_ETH_CFG1		0x00000400	/* PB 21	*/
 #define CFG_PB_ETH_CFG2		0x00000200	/* PB 22	*/
 #define CFG_PB_ETH_CFG3		0x00000100	/* PB 23	*/

 /* Ethernet settings:
  * MDIO not disabled, autonegotiation, 10/100Mbps, half/full duplex
  */
 #define CFG_ETH_MDDIS_VALUE	0
 #define CFG_ETH_CFG1_VALUE	1
 #define CFG_ETH_CFG2_VALUE	1
 #define CFG_ETH_CFG3_VALUE	1

 /* PUMA configuration */
 #define CFG_PC_PUMA_PROG	0x0200		/* PC  6        */
 #define CFG_PC_PUMA_DONE	0x0008		/* PC 12	*/
 #define CFG_PC_PUMA_INIT	0x0004		/* PC 13	*/

 #define	CFG_HZ		1000		/* decrementer freq: 1 ms ticks	*/

 #define CFG_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }

 /*
  * Low Level Configuration Settings
  * (address mappings, register initial values, etc.)
  * You should know what you are doing if you make changes here.
  */
 /*-----------------------------------------------------------------------
  * Internal Memory Mapped Register
  */
 #define CFG_IMMR		0xF0000000

 /*-----------------------------------------------------------------------
  * Definitions for initial stack pointer and data area (in DPRAM)
  */
 #define CFG_INIT_RAM_ADDR	CFG_IMMR
 #define	CFG_INIT_RAM_END	0x2F00	/* End of used area in DPRAM	*/
 #define	CFG_GBL_DATA_SIZE	64  /* size in bytes reserved for initial data */
 #define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
 #define	CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET

 /*-----------------------------------------------------------------------
  * Address accessed to reset the board - must not be mapped/assigned
  */
 #define	CFG_RESET_ADDRESS	0xFEFFFFFF

 /*-----------------------------------------------------------------------
  * Start addresses for the final memory configuration
  * (Set up by the startup code)
  * Please note that CFG_SDRAM_BASE _must_ start at 0
  */
 #define	CFG_SDRAM_BASE		0x00000000
 #define CFG_FLASH_BASE		0x40000000
 #if defined(DEBUG)
 #define	CFG_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor	*/
 #else
 #define	CFG_MONITOR_LEN		(192 << 10)	/* Reserve 192 kB for Monitor	*/
 #endif
 #define CFG_MONITOR_BASE	CFG_FLASH_BASE
 #define	CFG_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()	*/

 /*
  * For booting Linux, the board info and command line data
  * have to be in the first 8 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization.
  */
 #define	CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux	*/

 /*-----------------------------------------------------------------------
  * FLASH organization
  */
 #define CFG_MAX_FLASH_BANKS	2	/* max number of memory banks		*/
 #define CFG_MAX_FLASH_SECT	67	/* max number of sectors on one chip	*/

 #define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
 #define CFG_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/

 #if 1
 /* Start port with environment in flash; switch to SPI EEPROM later */
 #define	CFG_ENV_IS_IN_FLASH	1
 #define	CFG_ENV_OFFSET		0x8000	/*   Offset   of Environment Sector	*/
 #define	CFG_ENV_SIZE		0x4000	/* Total Size of Environment Sector	*/

 /* Address and size of Redundant Environment Sector	*/
 #define CFG_ENV_OFFSET_REDUND	(CFG_ENV_OFFSET+CFG_ENV_SIZE)
 #define CFG_ENV_SIZE_REDUND	(CFG_ENV_SIZE)
 #else
 /* Final version: environment in EEPROM */
 #define CFG_ENV_IS_IN_EEPROM	1
 #define CFG_ENV_OFFSET		2048
 #define CFG_ENV_SIZE		2048
 #endif

 /*-----------------------------------------------------------------------
  * Hardware Information Block
  */
 #define CFG_HWINFO_OFFSET	0x0003FFC0	/* offset of HW Info block */
 #define CFG_HWINFO_SIZE		0x00000040	/* size   of HW Info block */
 #define CFG_HWINFO_MAGIC	0x54514D38	/* 'TQM8' */

 /*-----------------------------------------------------------------------
  * Cache Configuration
  */
 #define CFG_CACHELINE_SIZE	16	/* For all MPC8xx CPUs			*/
 #define CFG_CACHELINE_SHIFT	4	/* log base 2 of the above value	*/

 /*-----------------------------------------------------------------------
  * SYPCR - System Protection Control				11-9
  * SYPCR can only be written once after reset!
  *-----------------------------------------------------------------------
  * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
  */
 #if defined(CONFIG_WATCHDOG)
 #define CFG_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
 			 SYPCR_SWE  | SYPCR_SWRI| SYPCR_SWP)
 #else
 #define CFG_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
 						  SYPCR_SWP)
 #endif

 /*-----------------------------------------------------------------------
  * SIUMCR - SIU Module Configuration				11-6
  *-----------------------------------------------------------------------
  * we must activate GPL5 in the SIUMCR for CAN
  */
 #define CFG_SIUMCR	(SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01)

 /*-----------------------------------------------------------------------
  * TBSCR - Time Base Status and Control				11-26
  *-----------------------------------------------------------------------
  * Clear Reference Interrupt Status, Timebase freezing enabled
  */
 #define CFG_TBSCR	(TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)

 /*-----------------------------------------------------------------------
  * RTCSC - Real-Time Clock Status and Control Register		11-27
  *-----------------------------------------------------------------------
  */
 #define CFG_RTCSC	(RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE)

 /*-----------------------------------------------------------------------
  * PISCR - Periodic Interrupt Status and Control		11-31
  *-----------------------------------------------------------------------
  * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
  */
 #define CFG_PISCR	(PISCR_PS | PISCR_PITF)

 /*-----------------------------------------------------------------------
  * PLPRCR - PLL, Low-Power, and Reset Control Register		15-30
  *-----------------------------------------------------------------------
  * Reset PLL lock status sticky bit, timer expired status bit and timer
  * interrupt status bit
  *
  * If this is a 80 MHz CPU, set PLL multiplication factor to 5 (5*16=80)!
  */
 #ifdef	CCM_80MHz	/* for 80 MHz, we use a 16 MHz clock * 5 */
 #define CFG_PLPRCR							\
 		( (5-1)<<PLPRCR_MF_SHIFT | PLPRCR_TEXPS | PLPRCR_TMIST )
 #else			/* up to 50 MHz we use a 1:1 clock */
 #define CFG_PLPRCR	(PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
 #endif	/* CCM_80MHz */

 /*-----------------------------------------------------------------------
  * SCCR - System Clock and reset Control Register		15-27
  *-----------------------------------------------------------------------
  * Set clock output, timebase and RTC source and divider,
  * power management and some other internal clocks
  */
 #define SCCR_MASK	SCCR_EBDF11
 #ifdef	CCM_80MHz	/* for 80 MHz, we use a 16 MHz clock * 5 */
 #define CFG_SCCR	(/* SCCR_TBS  | */ \
 			 SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
 			 SCCR_DFNL000 | SCCR_DFNH000  | SCCR_DFLCD000 | \
 			 SCCR_DFALCD00)
 #else			/* up to 50 MHz we use a 1:1 clock */
 #define CFG_SCCR	(SCCR_TBS     | \
 			 SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
 			 SCCR_DFNL000 | SCCR_DFNH000  | SCCR_DFLCD000 | \
 			 SCCR_DFALCD00)
 #endif	/* CCM_80MHz */

 /*-----------------------------------------------------------------------
  *
  * Interrupt Levels
  *-----------------------------------------------------------------------
  */
 #define CFG_CPM_INTERRUPT	13	/* SIU_LEVEL6	*/

 /*-----------------------------------------------------------------------
  *
  *-----------------------------------------------------------------------
  *
  */
 #define CFG_DER	0

 /*
  * Init Memory Controller:
  *
  * BR0/1 and OR0/1 (FLASH)
  */

 #define FLASH_BASE0_PRELIM	0x40000000	/* FLASH bank #0	*/
 #define FLASH_BASE1_PRELIM	0x60000000	/* FLASH bank #0	*/

 /* used to re-map FLASH both when starting from SRAM or FLASH:
  * restrict access enough to keep SRAM working (if any)
  * but not too much to meddle with FLASH accesses
  */
 #define CFG_REMAP_OR_AM		0x80000000	/* OR addr mask */
 #define CFG_PRELIM_OR_AM	0xE0000000	/* OR addr mask */

 /* FLASH timing: ACS = 11, TRLX = 0, CSNT = 1, SCY = 5, EHTR = 1	*/
 #define CFG_OR_TIMING_FLASH	(OR_CSNT_SAM  | OR_ACS_DIV2 | OR_BI | \
 				 OR_SCY_5_CLK | OR_EHTR)

 #define CFG_OR0_REMAP	(CFG_REMAP_OR_AM  | CFG_OR_TIMING_FLASH)
 #define CFG_OR0_PRELIM	(CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH)
 #define CFG_BR0_PRELIM	((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V )

 #define CFG_OR1_REMAP	CFG_OR0_REMAP
 #define CFG_OR1_PRELIM	CFG_OR0_PRELIM
 #define CFG_BR1_PRELIM	((FLASH_BASE1_PRELIM & BR_BA_MSK) | BR_V )

 /*
  * BR2 and OR2 (SDRAM)
  *
  */
 #define SDRAM_BASE2_PRELIM	0x00000000	/* SDRAM bank #0	*/
 #define SDRAM_BASE3_PRELIM	0x20000000	/* SDRAM bank #1	*/
 #define	SDRAM_MAX_SIZE		0x04000000	/* max 64 MB per bank	*/

 /* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care)	*/
 #define CFG_OR_TIMING_SDRAM	0x00000A00

 #define CFG_OR2_PRELIM	(CFG_PRELIM_OR_AM | CFG_OR_TIMING_SDRAM )
 #define CFG_BR2_PRELIM	((SDRAM_BASE2_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )

 /*
  * BR3 and OR3 (CAN Controller)
  */
 #define	CFG_CAN_BASE		0xC0000000	/* CAN mapped at 0xC0000000	*/
 #define CFG_CAN_OR_AM		0xFFFF8000	/* 32 kB address mask		*/
 #define CFG_OR3_CAN		(CFG_CAN_OR_AM | OR_G5LA | OR_BI)
 #define CFG_BR3_CAN		((CFG_CAN_BASE & BR_BA_MSK) | \
 					BR_PS_8 | BR_MS_UPMB | BR_V )

 /*
  * BR4/OR4: PUMA Config
  *
  * Memory controller will be used in 2 modes:
  *
  * - "read" mode:
  *	BR4: 0x10100801		OR4: 0xffff8520
  * - "load" mode (chip select on UPM B):
  *	BR4: 0x101004c1		OR4: 0xffff8600
  *
  * Default initialization is in "read" mode
  */
 #define PUMA_CONF_BASE		0x10100000	/* PUMA Config */
 #define PUMA_CONF_OR_AM		0xFFFF8000	/* 32 kB */
 #define	PUMA_CONF_LOAD_TIMING	(OR_ACS_DIV2	 | OR_SCY_2_CLK)
 #define PUMA_CONF_READ_TIMING	(OR_G5LA | OR_BI | OR_SCY_2_CLK)

 #define PUMA_CONF_BR_LOAD	((PUMA_CONF_BASE & BR_BA_MSK) | \
 					BR_PS_8  | BR_MS_UPMB | BR_V)
 #define PUMA_CONF_OR_LOAD	(PUMA_CONF_OR_AM | PUMA_CONF_LOAD_TIMING)

 #define PUMA_CONF_BR_READ	((PUMA_CONF_BASE & BR_BA_MSK) | BR_PS_16 | BR_V)
 #define PUMA_CONF_OR_READ	(PUMA_CONF_OR_AM | PUMA_CONF_READ_TIMING)

 #define CFG_BR4_PRELIM		PUMA_CONF_BR_READ
 #define CFG_OR4_PRELIM		PUMA_CONF_OR_READ

 /*
  * BR5/OR5: PUMA: SMA Bus 8 Bit
  *	BR5: 0x10200401		OR5: 0xffe0010a
  */
 #define PUMA_SMA8_BASE		0x10200000	/* PUMA SMA Bus 8 Bit */
 #define PUMA_SMA8_OR_AM		0xFFE00000	/* 2 MB */
 #define PUMA_SMA8_TIMING	(OR_BI | OR_SCY_0_CLK | OR_EHTR)

 #define CFG_BR5_PRELIM		((PUMA_SMA8_BASE & BR_BA_MSK) | BR_PS_8 | BR_V)
 #define CFG_OR5_PRELIM		(PUMA_SMA8_OR_AM | PUMA_SMA8_TIMING | OR_SETA)

 /*
  * BR6/OR6: PUMA: SMA Bus 16 Bit
  *	BR6: 0x10600801		OR6: 0xffe0010a
  */
 #define PUMA_SMA16_BASE		0x10600000	/* PUMA SMA Bus 16 Bit */
 #define PUMA_SMA16_OR_AM	0xFFE00000	/* 2 MB */
 #define PUMA_SMA16_TIMING	(OR_BI | OR_SCY_0_CLK | OR_EHTR)

 #define CFG_BR6_PRELIM		((PUMA_SMA16_BASE & BR_BA_MSK) | BR_PS_16 | BR_V)
 #define CFG_OR6_PRELIM		(PUMA_SMA16_OR_AM | PUMA_SMA16_TIMING | OR_SETA)

 /*
  * BR7/OR7: PUMA: external Flash
  *	BR7: 0x10a00801		OR7: 0xfe00010a
  */
 #define PUMA_FLASH_BASE		0x10A00000	/* PUMA external Flash */
 #define PUMA_FLASH_OR_AM	0xFE000000	/* 32 MB */
 #define PUMA_FLASH_TIMING	(OR_BI | OR_SCY_0_CLK | OR_EHTR)

 #define CFG_BR7_PRELIM		((PUMA_FLASH_BASE & BR_BA_MSK) | BR_PS_16 | BR_V)
 #define CFG_OR7_PRELIM		(PUMA_FLASH_OR_AM | PUMA_FLASH_TIMING | OR_SETA)


 /*
  * Memory Periodic Timer Prescaler
  */

 /* periodic timer for refresh */
 #define CFG_MAMR_PTA	97		/* start with divider for 100 MHz	*/

 /* refresh rate 15.6 us (= 64 ms / 4K = 62.4 / quad bursts) for <= 128 MBit	*/
 #define CFG_MPTPR_2BK_4K	MPTPR_PTP_DIV16		/* setting for 2 banks	*/
 #define CFG_MPTPR_1BK_4K	MPTPR_PTP_DIV32		/* setting for 1 bank	*/

 /* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit		*/
 #define CFG_MPTPR_2BK_8K	MPTPR_PTP_DIV8		/* setting for 2 banks	*/
 #define CFG_MPTPR_1BK_8K	MPTPR_PTP_DIV16		/* setting for 1 bank	*/

 /*
  * MAMR settings for SDRAM
  */

 /* 8 column SDRAM */
 #define CFG_MAMR_8COL	((CFG_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
 			 MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 |	\
 			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_4X)
 /* 9 column SDRAM */
 #define CFG_MAMR_9COL	((CFG_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
 			 MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 |	\
 			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_4X)


 /*
  * Internal Definitions
  *
  * Boot Flags
  */
 #define	BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH	*/
 #define BOOTFLAG_WARM	0x02		/* Software reboot			*/

 #endif	/* __CONFIG_H */
	/*
	* (C) Copyright 2001-2005
	* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
	*
	* See file CREDITS for list of people who contributed to this
	* project.
	*
	* This program is free software; you can redistribute it and/or
	* modify it under the terms of the GNU General Public License as
	* published by the Free Software Foundation; either version 2 of
	* the License, or (at your option) any later version.
	*
	* This program is distributed in the hope that it will be useful,
	* but WITHOUT ANY WARRANTY; without even the implied warranty of
	* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
	* GNU General Public License for more details.
	*
	* You should have received a copy of the GNU General Public License
	* along with this program; if not, write to the Free Software
	* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
	* MA 02111-1307 USA
	*/

	/*
	* configuration options, board specific, for Siemens Card Controller Module
	*/

	#ifndef __CONFIG_H
	#define __CONFIG_H

	#undef CCM_80MHz /* define for 80 MHz CPU only */

	/*
	* High Level Configuration Options
	* (easy to change)
	*/

	#define CONFIG_MPC860 1 /* This is a MPC860 CPU ... */
	#define CONFIG_CCM 1 /* on a Card Controller Module */

	#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
	#undef CONFIG_8xx_CONS_SMC2
	#undef CONFIG_8xx_CONS_NONE

	/* ENVIRONMENT */

	#define CONFIG_BAUDRATE 19200 /* console baudrate in bps */
	#define CONFIG_BOOTDELAY 2 /* autoboot after 2 seconds */

	#define CONFIG_IPADDR 192.168.0.42
	#define CONFIG_NETMASK 255.255.255.0
	#define CONFIG_GATEWAYIP 0.0.0.0
	#define CONFIG_SERVERIP 192.168.0.254

	#define CONFIG_HOSTNAME CCM

	#define CONFIG_LOADADDR 40180000

	#undef CONFIG_BOOTARGS

	#define CONFIG_BOOTCOMMAND "setenv bootargs " \
	"mem=${mem} " \
	"root=/dev/ram rw ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off " \
	"wt_8xx=timeout:3600; " \
	"bootm"

	#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
	#undef CFG_LOADS_BAUD_CHANGE /* don't allow baudrate change */

	#define CONFIG_WATCHDOG 1 /* watchdog enabled */

	#undef CONFIG_STATUS_LED /* Status LED disabled */

	#define CONFIG_PRAM 512 /* reserve 512kB "protected RAM"*/

	#define CONFIG_RTC_MPC8xx /* use internal RTC of MPC8xx */

	#define CONFIG_SPI /* enable SPI driver */
	#define CONFIG_SPI_X /* 16 bit EEPROM addressing */

	/* ----------------------------------------------------------------
	* Offset to initial SPI buffers in DPRAM (used if the environment
	* is in the SPI EEPROM): We need a 520 byte scratch DPRAM area to
	* use at an early stage. It is used between the two initialization
	* calls (spi_init_f() and spi_init_r()). The value 0xB00 makes it
	* far enough from the start of the data area (as well as from the
	* stack pointer).
	* ---------------------------------------------------------------- */
	#define CFG_SPI_INIT_OFFSET 0xB00

	#define CFG_EEPROM_PAGE_WRITE_BITS 5 /* 32-byte page size */


	#define CONFIG_MAC_PARTITION /* nod used yet */
	#define CONFIG_DOS_PARTITION

	#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT \| CONFIG_BOOTP_BOOTFILESIZE)


	/*
	* Command line configuration.
	*/
	#include <config_cmd_default.h>

	#define CONFIG_CMD_BSP
	#define CONFIG_CMD_DHCP
	#define CONFIG_CMD_DATE
	#define CONFIG_CMD_EEPROM
	#define CONFIG_CMD_NFS
	#define CONFIG_CMD_SNTP


	/*
	* Miscellaneous configurable options
	*/
	#define CFG_LONGHELP /* undef to save memory */
	#define CFG_PROMPT "=> " /* Monitor Command Prompt */
	#if defined(CONFIG_CMD_KGDB)
	#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
	#else
	#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
	#endif
	#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
	#define CFG_MAXARGS 16 /* max number of command args */
	#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */

	#define CFG_MEMTEST_START 0x00100000 /* memtest works on */
	#define CFG_MEMTEST_END 0x00F00000 /* 1 ... 15MB in DRAM */

	#define CFG_LOAD_ADDR 0x00100000 /* default load address */

	/* Ethernet hardware configuration done using port pins */
	#define CFG_PA_ETH_RESET 0x0200 /* PA 6 */
	#define CFG_PA_ETH_MDDIS 0x4000 /* PA 1 */
	#define CFG_PB_ETH_POWERDOWN 0x00000800 /* PB 20 */
	#define CFG_PB_ETH_CFG1 0x00000400 /* PB 21 */
	#define CFG_PB_ETH_CFG2 0x00000200 /* PB 22 */
	#define CFG_PB_ETH_CFG3 0x00000100 /* PB 23 */

	/* Ethernet settings:
	* MDIO not disabled, autonegotiation, 10/100Mbps, half/full duplex
	*/
	#define CFG_ETH_MDDIS_VALUE 0
	#define CFG_ETH_CFG1_VALUE 1
	#define CFG_ETH_CFG2_VALUE 1
	#define CFG_ETH_CFG3_VALUE 1

	/* PUMA configuration */
	#define CFG_PC_PUMA_PROG 0x0200 /* PC 6 */
	#define CFG_PC_PUMA_DONE 0x0008 /* PC 12 */
	#define CFG_PC_PUMA_INIT 0x0004 /* PC 13 */

	#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */

	#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }

	/*
	* Low Level Configuration Settings
	* (address mappings, register initial values, etc.)
	* You should know what you are doing if you make changes here.
	*/
	/*-----------------------------------------------------------------------
	* Internal Memory Mapped Register
	*/
	#define CFG_IMMR 0xF0000000

	/*-----------------------------------------------------------------------
	* Definitions for initial stack pointer and data area (in DPRAM)
	*/
	#define CFG_INIT_RAM_ADDR CFG_IMMR
	#define CFG_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */
	#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
	#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
	#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET

	/*-----------------------------------------------------------------------
	* Address accessed to reset the board - must not be mapped/assigned
	*/
	#define CFG_RESET_ADDRESS 0xFEFFFFFF

	/*-----------------------------------------------------------------------
	* Start addresses for the final memory configuration
	* (Set up by the startup code)
	* Please note that CFG_SDRAM_BASE _must_ start at 0
	*/
	#define CFG_SDRAM_BASE 0x00000000
	#define CFG_FLASH_BASE 0x40000000
	#if defined(DEBUG)
	#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
	#else
	#define CFG_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */
	#endif
	#define CFG_MONITOR_BASE CFG_FLASH_BASE
	#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */

	/*
	* For booting Linux, the board info and command line data
	* have to be in the first 8 MB of memory, since this is
	* the maximum mapped by the Linux kernel during initialization.
	*/
	#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */

	/*-----------------------------------------------------------------------
	* FLASH organization
	*/
	#define CFG_MAX_FLASH_BANKS 2 /* max number of memory banks */
	#define CFG_MAX_FLASH_SECT 67 /* max number of sectors on one chip */

	#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
	#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */

	#if 1
	/* Start port with environment in flash; switch to SPI EEPROM later */
	#define CFG_ENV_IS_IN_FLASH 1
	#define CFG_ENV_OFFSET 0x8000 /* Offset of Environment Sector */
	#define CFG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */

	/* Address and size of Redundant Environment Sector */
	#define CFG_ENV_OFFSET_REDUND (CFG_ENV_OFFSET+CFG_ENV_SIZE)
	#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE)
	#else
	/* Final version: environment in EEPROM */
	#define CFG_ENV_IS_IN_EEPROM 1
	#define CFG_ENV_OFFSET 2048
	#define CFG_ENV_SIZE 2048
	#endif

	/*-----------------------------------------------------------------------
	* Hardware Information Block
	*/
	#define CFG_HWINFO_OFFSET 0x0003FFC0 /* offset of HW Info block */
	#define CFG_HWINFO_SIZE 0x00000040 /* size of HW Info block */
	#define CFG_HWINFO_MAGIC 0x54514D38 /* 'TQM8' */

	/*-----------------------------------------------------------------------
	* Cache Configuration
	*/
	#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
	#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */

	/*-----------------------------------------------------------------------
	* SYPCR - System Protection Control 11-9
	* SYPCR can only be written once after reset!
	*-----------------------------------------------------------------------
	* Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
	*/
	#if defined(CONFIG_WATCHDOG)
	#define CFG_SYPCR (SYPCR_SWTC \| SYPCR_BMT \| SYPCR_BME \| SYPCR_SWF \| \
	SYPCR_SWE \| SYPCR_SWRI\| SYPCR_SWP)
	#else
	#define CFG_SYPCR (SYPCR_SWTC \| SYPCR_BMT \| SYPCR_BME \| SYPCR_SWF \| \
	SYPCR_SWP)
	#endif

	/*-----------------------------------------------------------------------
	* SIUMCR - SIU Module Configuration 11-6
	*-----------------------------------------------------------------------
	* we must activate GPL5 in the SIUMCR for CAN
	*/
	#define CFG_SIUMCR (SIUMCR_DBGC11 \| SIUMCR_DBPC00 \| SIUMCR_MLRC01)

	/*-----------------------------------------------------------------------
	* TBSCR - Time Base Status and Control 11-26
	*-----------------------------------------------------------------------
	* Clear Reference Interrupt Status, Timebase freezing enabled
	*/
	#define CFG_TBSCR (TBSCR_REFA \| TBSCR_REFB \| TBSCR_TBF)

	/*-----------------------------------------------------------------------
	* RTCSC - Real-Time Clock Status and Control Register 11-27
	*-----------------------------------------------------------------------
	*/
	#define CFG_RTCSC (RTCSC_SEC \| RTCSC_ALR \| RTCSC_RTF\| RTCSC_RTE)

	/*-----------------------------------------------------------------------
	* PISCR - Periodic Interrupt Status and Control 11-31
	*-----------------------------------------------------------------------
	* Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
	*/
	#define CFG_PISCR (PISCR_PS \| PISCR_PITF)

	/*-----------------------------------------------------------------------
	* PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
	*-----------------------------------------------------------------------
	* Reset PLL lock status sticky bit, timer expired status bit and timer
	* interrupt status bit
	*
	* If this is a 80 MHz CPU, set PLL multiplication factor to 5 (5*16=80)!
	*/
	#ifdef CCM_80MHz /* for 80 MHz, we use a 16 MHz clock * 5 */
	#define CFG_PLPRCR \
	( (5-1)<<PLPRCR_MF_SHIFT \| PLPRCR_TEXPS \| PLPRCR_TMIST )
	#else /* up to 50 MHz we use a 1:1 clock */
	#define CFG_PLPRCR (PLPRCR_SPLSS \| PLPRCR_TEXPS \| PLPRCR_TMIST)
	#endif /* CCM_80MHz */

	/*-----------------------------------------------------------------------
	* SCCR - System Clock and reset Control Register 15-27
	*-----------------------------------------------------------------------
	* Set clock output, timebase and RTC source and divider,
	* power management and some other internal clocks
	*/
	#define SCCR_MASK SCCR_EBDF11
	#ifdef CCM_80MHz /* for 80 MHz, we use a 16 MHz clock * 5 */
	#define CFG_SCCR (/* SCCR_TBS \| */ \
	SCCR_COM00 \| SCCR_DFSYNC00 \| SCCR_DFBRG00 \| \
	SCCR_DFNL000 \| SCCR_DFNH000 \| SCCR_DFLCD000 \| \
	SCCR_DFALCD00)
	#else /* up to 50 MHz we use a 1:1 clock */
	#define CFG_SCCR (SCCR_TBS \| \
	SCCR_COM00 \| SCCR_DFSYNC00 \| SCCR_DFBRG00 \| \
	SCCR_DFNL000 \| SCCR_DFNH000 \| SCCR_DFLCD000 \| \
	SCCR_DFALCD00)
	#endif /* CCM_80MHz */

	/*-----------------------------------------------------------------------
	*
	* Interrupt Levels
	*-----------------------------------------------------------------------
	*/
	#define CFG_CPM_INTERRUPT 13 /* SIU_LEVEL6 */

	/*-----------------------------------------------------------------------
	*
	*-----------------------------------------------------------------------
	*
	*/
	#define CFG_DER 0

	/*
	* Init Memory Controller:
	*
	* BR0/1 and OR0/1 (FLASH)
	*/

	#define FLASH_BASE0_PRELIM 0x40000000 /* FLASH bank #0 */
	#define FLASH_BASE1_PRELIM 0x60000000 /* FLASH bank #0 */

	/* used to re-map FLASH both when starting from SRAM or FLASH:
	* restrict access enough to keep SRAM working (if any)
	* but not too much to meddle with FLASH accesses
	*/
	#define CFG_REMAP_OR_AM 0x80000000 /* OR addr mask */
	#define CFG_PRELIM_OR_AM 0xE0000000 /* OR addr mask */

	/* FLASH timing: ACS = 11, TRLX = 0, CSNT = 1, SCY = 5, EHTR = 1 */
	#define CFG_OR_TIMING_FLASH (OR_CSNT_SAM \| OR_ACS_DIV2 \| OR_BI \| \
	OR_SCY_5_CLK \| OR_EHTR)

	#define CFG_OR0_REMAP (CFG_REMAP_OR_AM \| CFG_OR_TIMING_FLASH)
	#define CFG_OR0_PRELIM (CFG_PRELIM_OR_AM \| CFG_OR_TIMING_FLASH)
	#define CFG_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) \| BR_V )

	#define CFG_OR1_REMAP CFG_OR0_REMAP
	#define CFG_OR1_PRELIM CFG_OR0_PRELIM
	#define CFG_BR1_PRELIM ((FLASH_BASE1_PRELIM & BR_BA_MSK) \| BR_V )

	/*
	* BR2 and OR2 (SDRAM)
	*
	*/
	#define SDRAM_BASE2_PRELIM 0x00000000 /* SDRAM bank #0 */
	#define SDRAM_BASE3_PRELIM 0x20000000 /* SDRAM bank #1 */
	#define SDRAM_MAX_SIZE 0x04000000 /* max 64 MB per bank */

	/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */
	#define CFG_OR_TIMING_SDRAM 0x00000A00

	#define CFG_OR2_PRELIM (CFG_PRELIM_OR_AM \| CFG_OR_TIMING_SDRAM )
	#define CFG_BR2_PRELIM ((SDRAM_BASE2_PRELIM & BR_BA_MSK) \| BR_MS_UPMA \| BR_V )

	/*
	* BR3 and OR3 (CAN Controller)
	*/
	#define CFG_CAN_BASE 0xC0000000 /* CAN mapped at 0xC0000000 */
	#define CFG_CAN_OR_AM 0xFFFF8000 /* 32 kB address mask */
	#define CFG_OR3_CAN (CFG_CAN_OR_AM \| OR_G5LA \| OR_BI)
	#define CFG_BR3_CAN ((CFG_CAN_BASE & BR_BA_MSK) \| \
	BR_PS_8 \| BR_MS_UPMB \| BR_V )

	/*
	* BR4/OR4: PUMA Config
	*
	* Memory controller will be used in 2 modes:
	*
	* - "read" mode:
	* BR4: 0x10100801 OR4: 0xffff8520
	* - "load" mode (chip select on UPM B):
	* BR4: 0x101004c1 OR4: 0xffff8600
	*
	* Default initialization is in "read" mode
	*/
	#define PUMA_CONF_BASE 0x10100000 /* PUMA Config */
	#define PUMA_CONF_OR_AM 0xFFFF8000 /* 32 kB */
	#define PUMA_CONF_LOAD_TIMING (OR_ACS_DIV2 \| OR_SCY_2_CLK)
	#define PUMA_CONF_READ_TIMING (OR_G5LA \| OR_BI \| OR_SCY_2_CLK)

	#define PUMA_CONF_BR_LOAD ((PUMA_CONF_BASE & BR_BA_MSK) \| \
	BR_PS_8 \| BR_MS_UPMB \| BR_V)
	#define PUMA_CONF_OR_LOAD (PUMA_CONF_OR_AM \| PUMA_CONF_LOAD_TIMING)

	#define PUMA_CONF_BR_READ ((PUMA_CONF_BASE & BR_BA_MSK) \| BR_PS_16 \| BR_V)
	#define PUMA_CONF_OR_READ (PUMA_CONF_OR_AM \| PUMA_CONF_READ_TIMING)

	#define CFG_BR4_PRELIM PUMA_CONF_BR_READ
	#define CFG_OR4_PRELIM PUMA_CONF_OR_READ

	/*
	* BR5/OR5: PUMA: SMA Bus 8 Bit
	* BR5: 0x10200401 OR5: 0xffe0010a
	*/
	#define PUMA_SMA8_BASE 0x10200000 /* PUMA SMA Bus 8 Bit */
	#define PUMA_SMA8_OR_AM 0xFFE00000 /* 2 MB */
	#define PUMA_SMA8_TIMING (OR_BI \| OR_SCY_0_CLK \| OR_EHTR)

	#define CFG_BR5_PRELIM ((PUMA_SMA8_BASE & BR_BA_MSK) \| BR_PS_8 \| BR_V)
	#define CFG_OR5_PRELIM (PUMA_SMA8_OR_AM \| PUMA_SMA8_TIMING \| OR_SETA)

	/*
	* BR6/OR6: PUMA: SMA Bus 16 Bit
	* BR6: 0x10600801 OR6: 0xffe0010a
	*/
	#define PUMA_SMA16_BASE 0x10600000 /* PUMA SMA Bus 16 Bit */
	#define PUMA_SMA16_OR_AM 0xFFE00000 /* 2 MB */
	#define PUMA_SMA16_TIMING (OR_BI \| OR_SCY_0_CLK \| OR_EHTR)

	#define CFG_BR6_PRELIM ((PUMA_SMA16_BASE & BR_BA_MSK) \| BR_PS_16 \| BR_V)
	#define CFG_OR6_PRELIM (PUMA_SMA16_OR_AM \| PUMA_SMA16_TIMING \| OR_SETA)

	/*
	* BR7/OR7: PUMA: external Flash
	* BR7: 0x10a00801 OR7: 0xfe00010a
	*/
	#define PUMA_FLASH_BASE 0x10A00000 /* PUMA external Flash */
	#define PUMA_FLASH_OR_AM 0xFE000000 /* 32 MB */
	#define PUMA_FLASH_TIMING (OR_BI \| OR_SCY_0_CLK \| OR_EHTR)

	#define CFG_BR7_PRELIM ((PUMA_FLASH_BASE & BR_BA_MSK) \| BR_PS_16 \| BR_V)
	#define CFG_OR7_PRELIM (PUMA_FLASH_OR_AM \| PUMA_FLASH_TIMING \| OR_SETA)


	/*
	* Memory Periodic Timer Prescaler
	*/

	/* periodic timer for refresh */
	#define CFG_MAMR_PTA 97 /* start with divider for 100 MHz */

	/* refresh rate 15.6 us (= 64 ms / 4K = 62.4 / quad bursts) for <= 128 MBit */
	#define CFG_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */
	#define CFG_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */

	/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */
	#define CFG_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */
	#define CFG_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */

	/*
	* MAMR settings for SDRAM
	*/

	/* 8 column SDRAM */
	#define CFG_MAMR_8COL ((CFG_MAMR_PTA << MAMR_PTA_SHIFT) \| MAMR_PTAE \| \
	MAMR_AMA_TYPE_0 \| MAMR_DSA_1_CYCL \| MAMR_G0CLA_A11 \| \
	MAMR_RLFA_1X \| MAMR_WLFA_1X \| MAMR_TLFA_4X)
	/* 9 column SDRAM */
	#define CFG_MAMR_9COL ((CFG_MAMR_PTA << MAMR_PTA_SHIFT) \| MAMR_PTAE \| \
	MAMR_AMA_TYPE_1 \| MAMR_DSA_1_CYCL \| MAMR_G0CLA_A10 \| \
	MAMR_RLFA_1X \| MAMR_WLFA_1X \| MAMR_TLFA_4X)


	/*
	* Internal Definitions
	*
	* Boot Flags
	*/
	#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
	#define BOOTFLAG_WARM 0x02 /* Software reboot */

	#endif /* __CONFIG_H */