| /* |
| * A collection of structures, addresses, and values associated with |
| * the Motorola 860T FADS board. Copied from the MBX stuff. |
| * Magnus Damm added defines for 8xxrom and extended bd_info. |
| * Helmut Buchsbaum added bitvalues for BCSRx |
| * |
| * Copyright (c) 1998 Dan Malek (dmalek@jlc.net) |
| */ |
| |
| /* |
| * The GENIETV is using the following physical memorymap (copied from |
| * the FADS configuration): |
| * |
| * ff020000 -> ff02ffff : pcmcia |
| * ff010000 -> ff01ffff : BCSR connected to CS1, setup by 8xxROM |
| * ff000000 -> ff00ffff : IMAP internal in the cpu |
| * 30000000 -> 300fffff : flash connected to CS0 |
| * 00000000 -> nnnnnnnn : sdram setup by U-Boot |
| * |
| * CS pins are connected as follows: |
| * |
| * CS0 -512Kb boot flash |
| * CS1 - SDRAM #1 |
| * CS2 - SDRAM #2 |
| * CS3 - Flash #1 |
| * CS4 - Flash #2 |
| * CS5 - Lon (if present) |
| * CS6 - PCMCIA #1 |
| * CS7 - PCMCIA #2 |
| */ |
| |
| /* ------------------------------------------------------------------------- */ |
| |
| /* |
| * board/config.h - configuration options, board specific |
| */ |
| |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| #define CONFIG_ETHADDR 08:00:22:50:70:63 /* Ethernet address */ |
| #define CONFIG_ENV_OVERWRITE 1 /* Overwrite the environment */ |
| |
| #define CFG_ALLOC_DPRAM /* Use dynamic DPRAM allocation */ |
| |
| #define CFG_AUTOLOAD "n" /* No autoload */ |
| |
| /*#define CONFIG_VIDEO 1 / To enable the video initialization */ |
| /*#define CONFIG_VIDEO_ADDR 0x00200000 */ |
| /*#define CONFIG_HARD_I2C 1 / I2C with hardware support */ |
| /*#define CONFIG_PCMCIA 1 / To enable the PCMCIA initialization */ |
| |
| /*#define CFG_PCMCIA_IO_ADDR 0xff020000 */ |
| /*#define CFG_PCMCIA_IO_SIZE 0x10000 */ |
| /*#define CFG_PCMCIA_MEM_ADDR 0xe0000000 */ |
| /*#define CFG_PCMCIA_MEM_SIZE 0x10000 */ |
| |
| /* Video related */ |
| |
| /*#define CONFIG_VIDEO_LOGO 1 / Show the logo */ |
| /*#define CONFIG_VIDEO_ENCODER_AD7177 1 / Enable this encoder */ |
| /*#define CONFIG_VIDEO_ENCODER_AD7177_ADDR 0xF4 / ALSB to ground */ |
| |
| /* Wireless 56Khz 4PPM keyboard on SMCx */ |
| |
| /*#define CONFIG_KEYBOARD 0 */ |
| /*#define CONFIG_WL_4PPM_KEYBOARD_SMC 0 / SMC to use (0 indexed) */ |
| |
| /* |
| * High Level Configuration Options |
| * (easy to change) |
| */ |
| #include <mpc8xx_irq.h> |
| |
| #define CONFIG_GENIETV 1 |
| #define CONFIG_MPC823 1 |
| |
| #define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */ |
| #undef CONFIG_8xx_CONS_SMC2 |
| #undef CONFIG_8xx_CONS_NONE |
| #define CONFIG_BAUDRATE 9600 |
| |
| #define MPC8XX_FACT 12 /* Multiply by 12 */ |
| #define MPC8XX_XIN 5000000 /* 4 MHz clock */ |
| |
| #define MPC8XX_HZ ((MPC8XX_XIN) * (MPC8XX_FACT)) |
| #define CFG_PLPRCR_MF ((MPC8XX_FACT-1) << 20) |
| #define CONFIG_8xx_GCLK_FREQ MPC8XX_HZ /* Force it - dont measure it */ |
| |
| #define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */ |
| |
| #if 1 |
| #define CONFIG_BOOTDELAY 1 /* autoboot after 2 seconds */ |
| #define CONFIG_LOADS_ECHO 0 /* Dont echoes received characters */ |
| #define CONFIG_BOOTARGS "" |
| #define CONFIG_BOOTCOMMAND \ |
| "bootp; tftp; " \ |
| "setenv bootargs console=tty0 console=ttyS0 " \ |
| "root=/dev/nfs nfsroot=${serverip}:${rootpath} " \ |
| "ip=${ipaddr}:${serverip}:${gatewayip}:${subnetmask}:${hostname}:eth0:off ;" \ |
| "bootm " |
| #else |
| #define CONFIG_BOOTDELAY 0 /* autoboot disabled */ |
| #endif |
| |
| #undef CONFIG_WATCHDOG /* watchdog disabled */ |
| |
| |
| /* |
| * BOOTP options |
| */ |
| #define CONFIG_BOOTP_BOOTFILESIZE |
| #define CONFIG_BOOTP_BOOTPATH |
| #define CONFIG_BOOTP_GATEWAY |
| #define CONFIG_BOOTP_HOSTNAME |
| |
| |
| /* |
| * Command line configuration. |
| */ |
| #include <config_cmd_default.h> |
| |
| |
| /* |
| * Miscellaneous configurable options |
| */ |
| #define CFG_LONGHELP /* undef to save memory */ |
| #define CFG_PROMPT ":>" /* Monitor Command Prompt */ |
| #if defined(CONFIG_CMD_KGDB) |
| #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ |
| #else |
| #define CFG_CBSIZE 256 /* Console I/O Buffer Size */ |
| #endif |
| #define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ |
| #define CFG_MAXARGS 8 /* max number of command args */ |
| #define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ |
| |
| #define CFG_MEMTEST_START 0x00004000 /* memtest works on */ |
| #define CFG_MEMTEST_END 0x00800000 /* 0 ... 8 MB in DRAM */ |
| |
| #define CFG_LOAD_ADDR 0x00100000 /* default load address */ |
| |
| #define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ |
| |
| #define CFG_BAUDRATE_TABLE { 4800, 9600, 19200, 38400, 57600, 115200 } |
| |
| /* |
| * Low Level Configuration Settings |
| * (address mappings, register initial values, etc.) |
| * You should know what you are doing if you make changes here. |
| */ |
| /*----------------------------------------------------------------------- |
| * Internal Memory Mapped Register |
| */ |
| #define CFG_IMMR 0xFF000000 |
| #define CFG_IMMR_SIZE ((uint)(64 * 1024)) |
| |
| /*----------------------------------------------------------------------- |
| * Definitions for initial stack pointer and data area (in DPRAM) |
| */ |
| #define CFG_INIT_RAM_ADDR CFG_IMMR |
| #define CFG_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */ |
| #define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */ |
| #define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) |
| #define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET |
| |
| /*----------------------------------------------------------------------- |
| * Start addresses for the final memory configuration |
| * (Set up by the startup code) |
| * Please note that CFG_SDRAM_BASE _must_ start at 0 |
| * Also NOTE that it doesn't mean SDRAM - it means MEMORY. |
| */ |
| #define CFG_SDRAM_BASE 0x00000000 |
| #define CFG_FLASH_BASE 0x02800000 |
| #define CFG_FLASH_SIZE ((uint)(8 * 1024 * 1024)) /* max 8Mbyte */ |
| #if 0 |
| #define CFG_MONITOR_LEN (256 << 10) /* Reserve 128 kB for Monitor */ |
| #else |
| #define CFG_MONITOR_LEN (512 << 10) /* Reserve 512 kB for Monitor */ |
| #endif |
| #define CFG_MONITOR_BASE CFG_FLASH_BASE |
| #define CFG_MALLOC_LEN (256 << 10) /* Reserve 128 kB for malloc() */ |
| |
| /* |
| * For booting Linux, the board info and command line data |
| * have to be in the first 8 MB of memory, since this is |
| * the maximum mapped by the Linux kernel during initialization. |
| */ |
| #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ |
| /*----------------------------------------------------------------------- |
| * FLASH organization |
| */ |
| #define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ |
| #define CFG_MAX_FLASH_SECT 8 /* max number of sectors on one chip */ |
| |
| #define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ |
| #define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ |
| |
| #define CONFIG_ENV_IS_IN_FLASH 1 |
| #define CFG_ENV_OFFSET 0x10000 /* Offset of Environment Sector */ |
| #define CFG_ENV_SIZE 0x10000 /* Total Size of Environment Sector (64k)*/ |
| |
| /* values according to the manual */ |
| |
| /*----------------------------------------------------------------------- |
| * Cache Configuration |
| */ |
| #define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */ |
| #if defined(CONFIG_CMD_KGDB) |
| #define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */ |
| #endif |
| |
| /*----------------------------------------------------------------------- |
| * SYPCR - System Protection Control 11-9 |
| * SYPCR can only be written once after reset! |
| *----------------------------------------------------------------------- |
| * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze |
| */ |
| #if defined(CONFIG_WATCHDOG) |
| #define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ |
| SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP) |
| #else |
| #define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP) |
| #endif |
| |
| /*----------------------------------------------------------------------- |
| * SIUMCR - SIU Module Configuration 11-6 |
| *----------------------------------------------------------------------- |
| * PCMCIA config., multi-function pin tri-state |
| * |
| #define CFG_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01) |
| */ |
| #define CFG_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC10) |
| |
| /*----------------------------------------------------------------------- |
| * TBSCR - Time Base Status and Control 11-26 |
| *----------------------------------------------------------------------- |
| * Clear Reference Interrupt Status, Timebase freezing enabled |
| */ |
| #define CFG_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBE) |
| |
| /*----------------------------------------------------------------------- |
| * PISCR - Periodic Interrupt Status and Control 11-31 |
| *----------------------------------------------------------------------- |
| * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled |
| */ |
| #define CFG_PISCR (PISCR_PS | PISCR_PITF) |
| |
| /*----------------------------------------------------------------------- |
| * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30 |
| *----------------------------------------------------------------------- |
| * Reset PLL lock status sticky bit, timer expired status bit and timer * |
| * interrupt status bit - leave PLL multiplication factor unchanged ! |
| * |
| * #define CFG_PLPRCR (PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST) |
| */ |
| #define CFG_PLPRCR (PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST | CFG_PLPRCR_MF) |
| |
| /*----------------------------------------------------------------------- |
| * SCCR - System Clock and reset Control Register 15-27 |
| *----------------------------------------------------------------------- |
| * Set clock output, timebase and RTC source and divider, |
| * power management and some other internal clocks |
| */ |
| #define SCCR_MASK SCCR_EBDF11 |
| #define CFG_SCCR (SCCR_TBS | \ |
| SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \ |
| SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \ |
| SCCR_DFALCD00) |
| |
| /*----------------------------------------------------------------------- |
| * |
| *----------------------------------------------------------------------- |
| * |
| */ |
| #define CFG_DER 0 |
| |
| /* Because of the way the 860 starts up and assigns CS0 the |
| * entire address space, we have to set the memory controller |
| * differently. Normally, you write the option register |
| * first, and then enable the chip select by writing the |
| * base register. For CS0, you must write the base register |
| * first, followed by the option register. |
| */ |
| |
| /* |
| * Init Memory Controller: |
| * |
| * BR0 and OR0(FLASH) |
| */ |
| |
| #define FLASH_BASE0_PRELIM 0x02800000 /* FLASH bank #0 */ |
| |
| #define CFG_REMAP_OR_AM 0x80000000 /* OR addr mask */ |
| #define CFG_PRELIM_OR_AM 0xFF800000 /* OR addr mask (512Kb) */ |
| |
| /* FLASH timing */ |
| #define CFG_OR_TIMING_FLASH (OR_CSNT_SAM | OR_ACS_DIV2 | OR_BI | \ |
| OR_SCY_15_CLK | OR_TRLX ) |
| |
| /*#define CFG_OR0_REMAP (CFG_REMAP_OR_AM | CFG_OR_TIMING_FLASH) */ |
| #define CFG_OR0_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH) /* 0xfff80ff4 */ |
| #define CFG_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V | BR_PS_8) /* 0x02800401 */ |
| |
| /* |
| * BR1/2 and OR1/2 (SDRAM) |
| */ |
| |
| #define CFG_OR_TIMING_SDRAM 0x00000A00 |
| |
| #define SDRAM_MAX_SIZE 0x04000000 /* 64Mb bank */ |
| #define SDRAM_BASE1_PRELIM 0x00000000 /* First bank */ |
| #define SDRAM_BASE2_PRELIM 0x10000000 /* Second bank */ |
| |
| /* |
| * Memory Periodic Timer Prescaler |
| */ |
| |
| /* periodic timer for refresh */ |
| #define CFG_MBMR_PTB 0x5d /* start with divider for 100 MHz */ |
| |
| /* refresh rate 15.6 us (= 64 ms / 4K = 62.4 / quad bursts) for <= 128 MBit */ |
| #define CFG_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */ |
| #define CFG_MPTPR_1BK_4K MPTPR_PTP_DIV32 |
| /* |
| * MBMR settings for SDRAM |
| */ |
| |
| /* 8 column SDRAM */ |
| #define CFG_MBMR_8COL ((CFG_MBMR_PTB << MAMR_PTA_SHIFT) | MAMR_PTAE | \ |
| MAMR_G0CLA_A11 | MAMR_RLFA_1X | MAMR_WLFA_1X \ |
| | MAMR_TLFA_4X) /* 0x5d802114 */ |
| |
| /* |
| * Internal Definitions |
| * |
| * Boot Flags |
| */ |
| #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ |
| #define BOOTFLAG_WARM 0x02 /* Software reboot */ |
| |
| /* values according to the manual */ |
| |
| #define CONFIG_DRAM_50MHZ 1 |
| #define CONFIG_SDRAM_50MHZ |
| |
| /* We don't use the 8259. |
| */ |
| #define NR_8259_INTS 0 |
| |
| /* |
| * MPC8xx CPM Options |
| */ |
| #define CONFIG_SCC_ENET 1 |
| |
| #define CONFIG_DISK_SPINUP_TIME 1000000 |
| |
| /* PCMCIA configuration */ |
| |
| #define PCMCIA_MAX_SLOTS 1 |
| #define PCMCIA_SLOT_B 1 |
| |
| #endif /* __CONFIG_H */ |