| /* |
| * (C) Copyright 2005-2007 |
| * Stefan Roese, DENX Software Engineering, sr@denx.de. |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| /************************************************************************ |
| * bamboo.h - configuration for BAMBOO board |
| ***********************************************************************/ |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| /*----------------------------------------------------------------------- |
| * High Level Configuration Options |
| *----------------------------------------------------------------------*/ |
| #define CONFIG_BAMBOO 1 /* Board is BAMBOO */ |
| #define CONFIG_440EP 1 /* Specific PPC440EP support */ |
| #define CONFIG_440 1 /* ... PPC440 family */ |
| #define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */ |
| |
| #ifndef CONFIG_SYS_TEXT_BASE |
| #define CONFIG_SYS_TEXT_BASE 0xFFFA0000 |
| #endif |
| |
| /* |
| * Include common defines/options for all AMCC eval boards |
| */ |
| #define CONFIG_HOSTNAME bamboo |
| #include "amcc-common.h" |
| |
| /* Reclaim some space. */ |
| #undef CONFIG_SYS_LONGHELP |
| |
| #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ |
| |
| /* |
| * Please note that, if NAND support is enabled, the 2nd ethernet port |
| * can't be used because of pin multiplexing. So, if you want to use the |
| * 2nd ethernet port you have to "undef" the following define. |
| */ |
| #define CONFIG_BAMBOO_NAND 1 /* enable nand flash support */ |
| |
| /*----------------------------------------------------------------------- |
| * Base addresses -- Note these are effective addresses where the |
| * actual resources get mapped (not physical addresses) |
| *----------------------------------------------------------------------*/ |
| #define CONFIG_SYS_FLASH_BASE 0xfff00000 /* start of FLASH */ |
| #define CONFIG_SYS_PCI_MEMBASE 0xa0000000 /* mapped pci memory*/ |
| #define CONFIG_SYS_PCI_MEMBASE1 CONFIG_SYS_PCI_MEMBASE + 0x10000000 |
| #define CONFIG_SYS_PCI_MEMBASE2 CONFIG_SYS_PCI_MEMBASE1 + 0x10000000 |
| #define CONFIG_SYS_PCI_MEMBASE3 CONFIG_SYS_PCI_MEMBASE2 + 0x10000000 |
| |
| /*Don't change either of these*/ |
| #define CONFIG_SYS_PCI_BASE 0xe0000000 /* internal PCI regs*/ |
| /*Don't change either of these*/ |
| |
| #define CONFIG_SYS_USB_DEVICE 0x50000000 |
| #define CONFIG_SYS_NVRAM_BASE_ADDR 0x80000000 |
| #define CONFIG_SYS_BOOT_BASE_ADDR 0xf0000000 |
| #define CONFIG_SYS_NAND_ADDR 0x90000000 |
| #define CONFIG_SYS_NAND2_ADDR 0x94000000 |
| |
| /*----------------------------------------------------------------------- |
| * Initial RAM & stack pointer (placed in SDRAM) |
| *----------------------------------------------------------------------*/ |
| #define CONFIG_SYS_INIT_RAM_DCACHE 1 /* d-cache as init ram */ |
| #define CONFIG_SYS_INIT_RAM_ADDR 0x70000000 /* DCache */ |
| #define CONFIG_SYS_INIT_RAM_SIZE (4 << 10) |
| #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) |
| #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET |
| |
| /*----------------------------------------------------------------------- |
| * Serial Port |
| *----------------------------------------------------------------------*/ |
| #define CONFIG_CONS_INDEX 1 /* Use UART0 */ |
| #define CONFIG_SYS_EXT_SERIAL_CLOCK 11059200 /* use external 11.059MHz clk */ |
| |
| /*----------------------------------------------------------------------- |
| * NVRAM/RTC |
| * |
| * NOTE: The RTC registers are located at 0x7FFF0 - 0x7FFFF |
| * The DS1558 code assumes this condition |
| * |
| *----------------------------------------------------------------------*/ |
| #define CONFIG_SYS_NVRAM_SIZE (0x2000 - 0x10) /* NVRAM size(8k)- RTC regs */ |
| #define CONFIG_RTC_DS1556 1 /* DS1556 RTC */ |
| |
| /*----------------------------------------------------------------------- |
| * Environment |
| *----------------------------------------------------------------------*/ |
| #define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */ |
| |
| /*----------------------------------------------------------------------- |
| * FLASH related |
| *----------------------------------------------------------------------*/ |
| #define CONFIG_SYS_MAX_FLASH_BANKS 3 /* number of banks */ |
| #define CONFIG_SYS_MAX_FLASH_SECT 256 /* sectors per device */ |
| |
| #undef CONFIG_SYS_FLASH_CHECKSUM |
| #define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ |
| #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ |
| |
| #define CONFIG_SYS_FLASH_ADDR0 0x555 |
| #define CONFIG_SYS_FLASH_ADDR1 0x2aa |
| #define CONFIG_SYS_FLASH_WORD_SIZE unsigned char |
| |
| #define CONFIG_SYS_FLASH_2ND_16BIT_DEV 1 /* bamboo has 8 and 16bit device */ |
| #define CONFIG_SYS_FLASH_2ND_ADDR 0x87800000 /* bamboo has 8 and 16bit device */ |
| |
| #ifdef CONFIG_ENV_IS_IN_FLASH |
| #define CONFIG_ENV_SECT_SIZE 0x10000 /* size of one complete sector */ |
| #define CONFIG_ENV_ADDR ((-CONFIG_SYS_MONITOR_LEN)-CONFIG_ENV_SECT_SIZE) |
| #define CONFIG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */ |
| |
| /* Address and size of Redundant Environment Sector */ |
| #define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE) |
| #define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) |
| #endif /* CONFIG_ENV_IS_IN_FLASH */ |
| |
| /*----------------------------------------------------------------------- |
| * NAND FLASH |
| *----------------------------------------------------------------------*/ |
| #define CONFIG_SYS_MAX_NAND_DEVICE 2 |
| #define CONFIG_SYS_NAND_BASE (CONFIG_SYS_NAND_ADDR + CONFIG_SYS_NAND_CS) |
| #define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_ADDR + 2 } |
| #define CONFIG_SYS_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl. chips */ |
| #define CONFIG_SYS_NAND_CS 1 |
| |
| /*----------------------------------------------------------------------- |
| * DDR SDRAM |
| *----------------------------------------------------------------------------- */ |
| #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for setup */ |
| #undef CONFIG_DDR_ECC /* don't use ECC */ |
| #define CONFIG_SYS_SIMULATE_SPD_EEPROM 0xff /* simulate spd eeprom on this address */ |
| #define SPD_EEPROM_ADDRESS {CONFIG_SYS_SIMULATE_SPD_EEPROM, 0x50, 0x51} |
| #define CONFIG_SYS_MBYTES_SDRAM (64) /* 64MB fixed size for early-sdram-init */ |
| #define CONFIG_PROG_SDRAM_TLB |
| |
| /*----------------------------------------------------------------------- |
| * I2C |
| *----------------------------------------------------------------------*/ |
| #define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 |
| |
| #define CONFIG_SYS_I2C_EEPROM_ADDR (0xa8>>1) |
| #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 |
| #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 |
| #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 |
| |
| #ifdef CONFIG_ENV_IS_IN_EEPROM |
| #define CONFIG_ENV_SIZE 0x200 /* Size of Environment vars */ |
| #define CONFIG_ENV_OFFSET 0x0 |
| #endif /* CONFIG_ENV_IS_IN_EEPROM */ |
| |
| /* |
| * Default environment variables |
| */ |
| #define CONFIG_EXTRA_ENV_SETTINGS \ |
| CONFIG_AMCC_DEF_ENV \ |
| CONFIG_AMCC_DEF_ENV_POWERPC \ |
| CONFIG_AMCC_DEF_ENV_PPC_OLD \ |
| CONFIG_AMCC_DEF_ENV_NOR_UPD \ |
| "kernel_addr=fff00000\0" \ |
| "ramdisk_addr=fff10000\0" \ |
| "" |
| |
| #define CONFIG_HAS_ETH0 |
| #define CONFIG_PHY_ADDR 0 /* PHY address, See schematics */ |
| #define CONFIG_PHY1_ADDR 1 |
| |
| #ifndef CONFIG_BAMBOO_NAND |
| #define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */ |
| #endif /* CONFIG_BAMBOO_NAND */ |
| |
| #ifdef CONFIG_440EP |
| /* USB */ |
| #define CONFIG_USB_OHCI |
| |
| /*Comment this out to enable USB 1.1 device*/ |
| #define USB_2_0_DEVICE |
| #endif /*CONFIG_440EP*/ |
| |
| /* |
| * Commands additional to the ones defined in amcc-common.h |
| */ |
| #define CONFIG_CMD_DATE |
| #define CONFIG_CMD_PCI |
| #define CONFIG_CMD_SDRAM |
| |
| #ifdef CONFIG_BAMBOO_NAND |
| #define CONFIG_CMD_NAND |
| #endif |
| |
| #define CONFIG_SUPPORT_VFAT |
| |
| /* Partitions */ |
| #define CONFIG_MAC_PARTITION |
| #define CONFIG_DOS_PARTITION |
| #define CONFIG_ISO_PARTITION |
| |
| /*----------------------------------------------------------------------- |
| * PCI stuff |
| *----------------------------------------------------------------------- |
| */ |
| /* General PCI */ |
| #define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */ |
| #undef CONFIG_PCI_PNP /* do (not) pci plug-and-play */ |
| #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ |
| #define CONFIG_SYS_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CONFIG_SYS_PCI_MEMBASE*/ |
| |
| /* Board-specific PCI */ |
| #define CONFIG_SYS_PCI_TARGET_INIT |
| #define CONFIG_SYS_PCI_MASTER_INIT |
| |
| #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */ |
| #define CONFIG_SYS_PCI_SUBSYS_ID 0xcafe /* Whatever */ |
| |
| #endif /* __CONFIG_H */ |