board/BuR/zynq: initial commit
This commit adds support for the brcp1, brsmarc2, brcp150 and brcp170
boards. This boards are based on the Xilinx Zynq SoC.
Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20250404072819.69642-5-bernhard.messerklinger@br-automation.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
diff --git a/arch/arm/dts/zynq-brcp1.dtsi b/arch/arm/dts/zynq-brcp1.dtsi
new file mode 100644
index 0000000..ebaf42d
--- /dev/null
+++ b/arch/arm/dts/zynq-brcp1.dtsi
@@ -0,0 +1,131 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2024 B&R Industrial Automation GmbH
+ */
+
+/include/ "zynq-7000.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ model = "BRCP1 CPU";
+ compatible = "br,cp1",
+ "xlnx,zynq-7000";
+
+ aliases {
+ i2c0 = &i2c0;
+ serial0 = &uart0;
+ spi0 = &qspi;
+ mmc0 = &sdhci0;
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x0 0x40000000>;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ usb_phy0: phy0 {
+ compatible = "usb-nop-xceiv";
+ #phy-cells = <0>;
+ };
+
+ brd_rst: board_reset {
+ compatible = "br,board-reset";
+ pin = <&gpio0 9 GPIO_ACTIVE_HIGH>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ se_green {
+ label = "S_E_GREEN";
+ gpios = <&ledgpio 0 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ };
+ se_red {
+ label = "S_E_RED";
+ gpios = <&ledgpio 1 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ };
+ rdy_f_yellow {
+ label = "RDY_F_YELLOW";
+ gpios = <&ledgpio 2 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ };
+ re_green {
+ label = "R_E_GREEN";
+ gpios = <&ledgpio 3 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ };
+ re_red {
+ label = "R_E_RED";
+ gpios = <&ledgpio 4 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ plk_se_green {
+ label = "PLK_S_E_GREEN";
+ gpios = <&ledgpio 5 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ };
+ eth_se_green {
+ label = "ETH_S_E_GREEN";
+ gpios = <&ledgpio 6 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ };
+ };
+};
+
+&i2c0 {
+ status = "okay";
+ clock-frequency = <100000>;
+
+ ledgpio: max7320@5d { /* board LED */
+ status = "okay";
+ compatible = "maxim,max7320";
+ reg = <0x5d>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ ngpios = <8>;
+ };
+
+ pmic0: da9062@58 {
+ compatible = "dlg,da9062";
+ reg = <0x58>;
+ };
+};
+
+&sdhci0 {
+ status = "okay";
+ max-frequency = <25000000>;
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&qspi {
+ status = "okay";
+ spi-max-frequency = <100000000>;
+
+ spi_flash: spiflash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "jedec,spi-nor", "spi-flash", "s25fl256s1";
+ spi-max-frequency = <100000000>;
+ spi-cpol;
+ spi-cpha;
+ reg = <0>;
+ };
+};
+
+&usb0 {
+ status = "okay";
+ dr_mode = "host";
+ usb-phy = <&usb_phy0>;
+};
+
+&gpio0 {
+ status = "okay";
+};