include/init.h - filogic/uboot - Gitiles

 /* SPDX-License-Identifier: GPL-2.0+ */
 /*
  * (C) Copyright 2000-2009
  * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
  *
  * Copy the startup prototype, previously defined in common.h
  * Copyright (C) 2018, STMicroelectronics - All Rights Reserved
  */

 #ifndef __INIT_H_
 #define __INIT_H_	1

 #ifndef __ASSEMBLY__		/* put C only stuff in this section */

 #include <linux/types.h>

 /*
  * In case of the EFI app the UEFI firmware provides the low-level
  * initialisation.
  */
 #ifdef CONFIG_EFI
 #define ll_boot_init()	false
 #else
 #include <asm/global_data.h>

 #define ll_boot_init()	(!(gd->flags & GD_FLG_SKIP_LL_INIT))
 #endif

 /*
  * Function Prototypes
  */

 /* common/board_f.c */
 void board_init_f(ulong dummy);

 /**
  * arch_cpu_init() - basic cpu-dependent setup for an architecture
  *
  * This is called after early malloc is available. It should handle any
  * CPU- or SoC- specific init needed to continue the init sequence. See
  * board_f.c for where it is called. If this is not provided, a default
  * version (which does nothing) will be used.
  *
  * Return: 0 on success, otherwise error
  */
 int arch_cpu_init(void);

 /**
  * arch_cpu_init_dm() - init CPU after driver model is available
  *
  * This is called immediately after driver model is available before
  * relocation. This is similar to arch_cpu_init() but is able to reference
  * devices
  *
  * Return: 0 if OK, -ve on error
  */
 int arch_cpu_init_dm(void);

 /**
  * mach_cpu_init() - SoC/machine dependent CPU setup
  *
  * This is called after arch_cpu_init(). It should handle any
  * SoC or machine specific init needed to continue the init sequence. See
  * board_f.c for where it is called. If this is not provided, a default
  * version (which does nothing) will be used.
  *
  * Return: 0 on success, otherwise error
  */
 int mach_cpu_init(void);

 /**
  * arch_fsp_init() - perform firmware support package init
  *
  * Where U-Boot relies on binary blobs to handle part of the system init, this
  * function can be used to set up the blobs. This is used on some Intel
  * platforms.
  *
  * Return: 0
  */
 int arch_fsp_init(void);

 /**
  * arch_fsp_init() - perform post-relocation firmware support package init
  *
  * Where U-Boot relies on binary blobs to handle part of the system init, this
  * function can be used to set up the blobs. This is used on some Intel
  * platforms.
  *
  * Return: 0
  */
 int arch_fsp_init_r(void);

 int dram_init(void);

 /**
  * dram_init_banksize() - Set up DRAM bank sizes
  *
  * This can be implemented by boards to set up the DRAM bank information in
  * gd->bd->bi_dram(). It is called just before relocation, after dram_init()
  * is called.
  *
  * If this is not provided, a default implementation will try to set up a
  * single bank. It will do this if CONFIG_NR_DRAM_BANKS and
  * CONFIG_SYS_SDRAM_BASE are set. The bank will have a start address of
  * CONFIG_SYS_SDRAM_BASE and the size will be determined by a call to
  * get_effective_memsize().
  *
  * Return: 0 if OK, -ve on error
  */
 int dram_init_banksize(void);

 long get_ram_size(long *base, long size);
 phys_size_t get_effective_memsize(void);

 int testdram(void);

 /**
  * arch_reserve_stacks() - Reserve all necessary stacks
  *
  * This is used in generic board init sequence in common/board_f.c. Each
  * architecture could provide this function to tailor the required stacks.
  *
  * On entry gd->start_addr_sp is pointing to the suggested top of the stack.
  * The callee ensures gd->start_add_sp is 16-byte aligned, so architectures
  * require only this can leave it untouched.
  *
  * On exit gd->start_addr_sp and gd->irq_sp should be set to the respective
  * positions of the stack. The stack pointer(s) will be set to this later.
  * gd->irq_sp is only required, if the architecture needs it.
  *
  * Return: 0 if no error
  */
 int arch_reserve_stacks(void);

 /**
  * arch_reserve_mmu() - Reserve memory for MMU TLB table
  *
  * Architecture-specific routine for reserving memory for the MMU TLB table.
  * This is used in generic board init sequence in common/board_f.c.
  *
  * If an implementation is not provided, it will just be a nop stub.
  *
  * Return: 0 if OK
  */
 int arch_reserve_mmu(void);

 /**
  * arch_setup_bdinfo() - Architecture dependent boardinfo setup
  *
  * Architecture-specific routine for populating various boardinfo fields of
  * gd->bd. It is called during the generic board init sequence.
  *
  * If an implementation is not provided, it will just be a nop stub.
  *
  * Return: 0 if OK
  */
 int arch_setup_bdinfo(void);

 /**
  * setup_bdinfo() - Generic boardinfo setup
  *
  * Routine for populating various generic boardinfo fields of
  * gd->bd. It is called during the generic board init sequence.
  *
  * Return: 0 if OK
  */
 int setup_bdinfo(void);

 /**
  * cpu_secondary_init_r() - CPU-specific secondary initialization
  *
  * After non-volatile devices, environment and cpu code are setup, have
  * another round to deal with any initialization that might require
  * full access to the environment or loading of some image (firmware)
  * from a non-volatile device.
  *
  * It is called during the generic post-relocation init sequence.
  *
  * Return: 0 if OK
  */
 int cpu_secondary_init_r(void);

 /**
  * pci_ep_init() - Initialize pci endpoint devices
  *
  * It is called during the generic post-relocation init sequence.
  *
  * Return: 0 if OK
  */
 int pci_ep_init(void);

 /**
  * pci_init() - Enumerate pci devices
  *
  * It is called during the generic post-relocation init sequence to enumerate
  * pci buses. This is needed, for instance, in the case of DM PCI-based
  * Ethernet devices, which will not be detected without having the enumeration
  * performed earlier.
  *
  * Return: 0 if OK
  */
 int pci_init(void);

 /**
  * init_cache_f_r() - Turn on the cache in preparation for relocation
  *
  * Return: 0 if OK, -ve on error
  */
 int init_cache_f_r(void);

 #if !CONFIG_IS_ENABLED(CPU)
 /**
  * print_cpuinfo() - Display information about the CPU
  *
  * Return: 0 if OK, -ve on error
  */
 int print_cpuinfo(void);
 #endif
 int timer_init(void);

 #if defined(CONFIG_DTB_RESELECT)
 int embedded_dtb_select(void);
 #endif

 /* common/init/board_init.c */
 extern ulong monitor_flash_len;

 /**
  * ulong board_init_f_alloc_reserve - allocate reserved area
  * @top: top of the reserve area, growing down.
  *
  * This function is called by each architecture very early in the start-up
  * code to allow the C runtime to reserve space on the stack for writable
  * 'globals' such as GD and the malloc arena.
  *
  * Return: bottom of reserved area
  */
 ulong board_init_f_alloc_reserve(ulong top);

 /**
  * board_init_f_init_reserve - initialize the reserved area(s)
  * @base:	top from which reservation was done
  *
  * This function is called once the C runtime has allocated the reserved
  * area on the stack. It must initialize the GD at the base of that area.
  */
 void board_init_f_init_reserve(ulong base);

 struct global_data;

 /**
  * arch_setup_gd() - Set up the global_data pointer
  * @gd_ptr: Pointer to global data
  *
  * This pointer is special in some architectures and cannot easily be assigned
  * to. For example on x86 it is implemented by adding a specific record to its
  * Global Descriptor Table! So we we provide a function to carry out this task.
  * For most architectures this can simply be:
  *
  *    gd = gd_ptr;
  */
 void arch_setup_gd(struct global_data *gd_ptr);

 /* common/board_r.c */
 void board_init_r(struct global_data *id, ulong dest_addr)
 	__attribute__ ((noreturn));

 int cpu_init_r(void);
 int last_stage_init(void);
 int mac_read_from_eeprom(void);
 int set_cpu_clk_info(void);
 int update_flash_size(int flash_size);
 int arch_early_init_r(void);
 int misc_init_r(void);
 #if defined(CONFIG_VID)
 int init_func_vid(void);
 #endif

 /* common/board_info.c */
 int checkboard(void);
 int show_board_info(void);

 /**
  * Get the uppermost pointer that is valid to access
  *
  * Some systems may not map all of their address space. This function allows
  * boards to indicate what their highest support pointer value is for DRAM
  * access.
  *
  * @param total_size	Size of U-Boot (unused?)
  */
 ulong board_get_usable_ram_top(ulong total_size);

 int board_early_init_f(void);

 /* manipulate the U-Boot fdt before its relocation */
 int board_fix_fdt(void *rw_fdt_blob);
 int board_late_init(void);
 int board_postclk_init(void); /* after clocks/timebase, before env/serial */
 int board_early_init_r(void);

 /**
  * arch_initr_trap() - Init traps
  *
  * Arch specific routine for initializing traps. It is called during the
  * generic board init sequence, after relocation.
  *
  * Return: 0 if OK
  */
 int arch_initr_trap(void);

 /**
  * init_addr_map()
  *
  * Initialize non-identity virtual-physical memory mappings for 32bit CPUs.
  * It is called during the generic board init sequence, after relocation.
  *
  * Return: 0 if OK
  */
 int init_addr_map(void);

 /**
  * main_loop() - Enter the main loop of U-Boot
  *
  * This normally runs the command line.
  */
 void main_loop(void);

 #if defined(CONFIG_ARM)
 void relocate_code(ulong addr_moni);
 #else
 void relocate_code(ulong start_addr_sp, struct global_data *new_gd,
 		   ulong relocaddr)
 	__attribute__ ((noreturn));
 #endif

 /* Print a numeric value (for use in arch_print_bdinfo()) */
 void bdinfo_print_num_l(const char *name, ulong value);
 void bdinfo_print_num_ll(const char *name, unsigned long long value);

 /* Print a clock speed in MHz */
 void bdinfo_print_mhz(const char *name, unsigned long hz);

 /* Show arch-specific information for the 'bd' command */
 void arch_print_bdinfo(void);

 int do_bdinfo(struct cmd_tbl *cmdtp, int flag, int argc, char *const argv[]);

 #endif	/* __ASSEMBLY__ */
 /* Put only stuff here that the assembler can digest */

 #endif	/* __INIT_H_ */
	/* SPDX-License-Identifier: GPL-2.0+ */
	/*
	* (C) Copyright 2000-2009
	* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
	*
	* Copy the startup prototype, previously defined in common.h
	* Copyright (C) 2018, STMicroelectronics - All Rights Reserved
	*/

	#ifndef __INIT_H_
	#define __INIT_H_ 1

	#ifndef __ASSEMBLY__ /* put C only stuff in this section */

	#include <linux/types.h>

	/*
	* In case of the EFI app the UEFI firmware provides the low-level
	* initialisation.
	*/
	#ifdef CONFIG_EFI
	#define ll_boot_init() false
	#else
	#include <asm/global_data.h>

	#define ll_boot_init() (!(gd->flags & GD_FLG_SKIP_LL_INIT))
	#endif

	/*
	* Function Prototypes
	*/

	/* common/board_f.c */
	void board_init_f(ulong dummy);

	/**
	* arch_cpu_init() - basic cpu-dependent setup for an architecture
	*
	* This is called after early malloc is available. It should handle any
	* CPU- or SoC- specific init needed to continue the init sequence. See
	* board_f.c for where it is called. If this is not provided, a default
	* version (which does nothing) will be used.
	*
	* Return: 0 on success, otherwise error
	*/
	int arch_cpu_init(void);

	/**
	* arch_cpu_init_dm() - init CPU after driver model is available
	*
	* This is called immediately after driver model is available before
	* relocation. This is similar to arch_cpu_init() but is able to reference
	* devices
	*
	* Return: 0 if OK, -ve on error
	*/
	int arch_cpu_init_dm(void);

	/**
	* mach_cpu_init() - SoC/machine dependent CPU setup
	*
	* This is called after arch_cpu_init(). It should handle any
	* SoC or machine specific init needed to continue the init sequence. See
	* board_f.c for where it is called. If this is not provided, a default
	* version (which does nothing) will be used.
	*
	* Return: 0 on success, otherwise error
	*/
	int mach_cpu_init(void);

	/**
	* arch_fsp_init() - perform firmware support package init
	*
	* Where U-Boot relies on binary blobs to handle part of the system init, this
	* function can be used to set up the blobs. This is used on some Intel
	* platforms.
	*
	* Return: 0
	*/
	int arch_fsp_init(void);

	/**
	* arch_fsp_init() - perform post-relocation firmware support package init
	*
	* Where U-Boot relies on binary blobs to handle part of the system init, this
	* function can be used to set up the blobs. This is used on some Intel
	* platforms.
	*
	* Return: 0
	*/
	int arch_fsp_init_r(void);

	int dram_init(void);

	/**
	* dram_init_banksize() - Set up DRAM bank sizes
	*
	* This can be implemented by boards to set up the DRAM bank information in
	* gd->bd->bi_dram(). It is called just before relocation, after dram_init()
	* is called.
	*
	* If this is not provided, a default implementation will try to set up a
	* single bank. It will do this if CONFIG_NR_DRAM_BANKS and
	* CONFIG_SYS_SDRAM_BASE are set. The bank will have a start address of
	* CONFIG_SYS_SDRAM_BASE and the size will be determined by a call to
	* get_effective_memsize().
	*
	* Return: 0 if OK, -ve on error
	*/
	int dram_init_banksize(void);

	long get_ram_size(long *base, long size);
	phys_size_t get_effective_memsize(void);

	int testdram(void);

	/**
	* arch_reserve_stacks() - Reserve all necessary stacks
	*
	* This is used in generic board init sequence in common/board_f.c. Each
	* architecture could provide this function to tailor the required stacks.
	*
	* On entry gd->start_addr_sp is pointing to the suggested top of the stack.
	* The callee ensures gd->start_add_sp is 16-byte aligned, so architectures
	* require only this can leave it untouched.
	*
	* On exit gd->start_addr_sp and gd->irq_sp should be set to the respective
	* positions of the stack. The stack pointer(s) will be set to this later.
	* gd->irq_sp is only required, if the architecture needs it.
	*
	* Return: 0 if no error
	*/
	int arch_reserve_stacks(void);

	/**
	* arch_reserve_mmu() - Reserve memory for MMU TLB table
	*
	* Architecture-specific routine for reserving memory for the MMU TLB table.
	* This is used in generic board init sequence in common/board_f.c.
	*
	* If an implementation is not provided, it will just be a nop stub.
	*
	* Return: 0 if OK
	*/
	int arch_reserve_mmu(void);

	/**
	* arch_setup_bdinfo() - Architecture dependent boardinfo setup
	*
	* Architecture-specific routine for populating various boardinfo fields of
	* gd->bd. It is called during the generic board init sequence.
	*
	* If an implementation is not provided, it will just be a nop stub.
	*
	* Return: 0 if OK
	*/
	int arch_setup_bdinfo(void);

	/**
	* setup_bdinfo() - Generic boardinfo setup
	*
	* Routine for populating various generic boardinfo fields of
	* gd->bd. It is called during the generic board init sequence.
	*
	* Return: 0 if OK
	*/
	int setup_bdinfo(void);

	/**
	* cpu_secondary_init_r() - CPU-specific secondary initialization
	*
	* After non-volatile devices, environment and cpu code are setup, have
	* another round to deal with any initialization that might require
	* full access to the environment or loading of some image (firmware)
	* from a non-volatile device.
	*
	* It is called during the generic post-relocation init sequence.
	*
	* Return: 0 if OK
	*/
	int cpu_secondary_init_r(void);

	/**
	* pci_ep_init() - Initialize pci endpoint devices
	*
	* It is called during the generic post-relocation init sequence.
	*
	* Return: 0 if OK
	*/
	int pci_ep_init(void);

	/**
	* pci_init() - Enumerate pci devices
	*
	* It is called during the generic post-relocation init sequence to enumerate
	* pci buses. This is needed, for instance, in the case of DM PCI-based
	* Ethernet devices, which will not be detected without having the enumeration
	* performed earlier.
	*
	* Return: 0 if OK
	*/
	int pci_init(void);

	/**
	* init_cache_f_r() - Turn on the cache in preparation for relocation
	*
	* Return: 0 if OK, -ve on error
	*/
	int init_cache_f_r(void);

	#if !CONFIG_IS_ENABLED(CPU)
	/**
	* print_cpuinfo() - Display information about the CPU
	*
	* Return: 0 if OK, -ve on error
	*/
	int print_cpuinfo(void);
	#endif
	int timer_init(void);

	#if defined(CONFIG_DTB_RESELECT)
	int embedded_dtb_select(void);
	#endif

	/* common/init/board_init.c */
	extern ulong monitor_flash_len;

	/**
	* ulong board_init_f_alloc_reserve - allocate reserved area
	* @top: top of the reserve area, growing down.
	*
	* This function is called by each architecture very early in the start-up
	* code to allow the C runtime to reserve space on the stack for writable
	* 'globals' such as GD and the malloc arena.
	*
	* Return: bottom of reserved area
	*/
	ulong board_init_f_alloc_reserve(ulong top);

	/**
	* board_init_f_init_reserve - initialize the reserved area(s)
	* @base: top from which reservation was done
	*
	* This function is called once the C runtime has allocated the reserved
	* area on the stack. It must initialize the GD at the base of that area.
	*/
	void board_init_f_init_reserve(ulong base);

	struct global_data;

	/**
	* arch_setup_gd() - Set up the global_data pointer
	* @gd_ptr: Pointer to global data
	*
	* This pointer is special in some architectures and cannot easily be assigned
	* to. For example on x86 it is implemented by adding a specific record to its
	* Global Descriptor Table! So we we provide a function to carry out this task.
	* For most architectures this can simply be:
	*
	* gd = gd_ptr;
	*/
	void arch_setup_gd(struct global_data *gd_ptr);

	/* common/board_r.c */
	void board_init_r(struct global_data *id, ulong dest_addr)
	__attribute__ ((noreturn));

	int cpu_init_r(void);
	int last_stage_init(void);
	int mac_read_from_eeprom(void);
	int set_cpu_clk_info(void);
	int update_flash_size(int flash_size);
	int arch_early_init_r(void);
	int misc_init_r(void);
	#if defined(CONFIG_VID)
	int init_func_vid(void);
	#endif

	/* common/board_info.c */
	int checkboard(void);
	int show_board_info(void);

	/**
	* Get the uppermost pointer that is valid to access
	*
	* Some systems may not map all of their address space. This function allows
	* boards to indicate what their highest support pointer value is for DRAM
	* access.
	*
	* @param total_size Size of U-Boot (unused?)
	*/
	ulong board_get_usable_ram_top(ulong total_size);

	int board_early_init_f(void);

	/* manipulate the U-Boot fdt before its relocation */
	int board_fix_fdt(void *rw_fdt_blob);
	int board_late_init(void);
	int board_postclk_init(void); /* after clocks/timebase, before env/serial */
	int board_early_init_r(void);

	/**
	* arch_initr_trap() - Init traps
	*
	* Arch specific routine for initializing traps. It is called during the
	* generic board init sequence, after relocation.
	*
	* Return: 0 if OK
	*/
	int arch_initr_trap(void);

	/**
	* init_addr_map()
	*
	* Initialize non-identity virtual-physical memory mappings for 32bit CPUs.
	* It is called during the generic board init sequence, after relocation.
	*
	* Return: 0 if OK
	*/
	int init_addr_map(void);

	/**
	* main_loop() - Enter the main loop of U-Boot
	*
	* This normally runs the command line.
	*/
	void main_loop(void);

	#if defined(CONFIG_ARM)
	void relocate_code(ulong addr_moni);
	#else
	void relocate_code(ulong start_addr_sp, struct global_data *new_gd,
	ulong relocaddr)
	__attribute__ ((noreturn));
	#endif

	/* Print a numeric value (for use in arch_print_bdinfo()) */
	void bdinfo_print_num_l(const char *name, ulong value);
	void bdinfo_print_num_ll(const char *name, unsigned long long value);

	/* Print a clock speed in MHz */
	void bdinfo_print_mhz(const char *name, unsigned long hz);

	/* Show arch-specific information for the 'bd' command */
	void arch_print_bdinfo(void);

	int do_bdinfo(struct cmd_tbl cmdtp, int flag, int argc, char const argv[]);

	#endif /* __ASSEMBLY__ */
	/* Put only stuff here that the assembler can digest */

	#endif /* __INIT_H_ */