| /* |
| * (C) Copyright 2003 Embedded Edge, LLC |
| * Dan Malek <dan@embeddededge.com> |
| * Copied from ADS85xx. |
| * Updates for Silicon Tx GP3 8560 board. |
| * |
| * (C) Copyright 2002,2003 Motorola,Inc. |
| * Xianghua Xiao <X.Xiao@motorola.com> |
| * |
| * See file CREDITS for list of people who contributed to this |
| * project. |
| * |
| * This program is free software; you can redistribute it and/or |
| * modify it under the terms of the GNU General Public License as |
| * published by the Free Software Foundation; either version 2 of |
| * the License, or (at your option) any later version. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| * |
| * You should have received a copy of the GNU General Public License |
| * along with this program; if not, write to the Free Software |
| * Foundation, Inc., 59 Temple Place, Suite 330, Boston, |
| * MA 02111-1307 USA |
| */ |
| |
| /* mpc8560ads board configuration file */ |
| /* please refer to doc/README.mpc85xx for more info */ |
| /* make sure you change the MAC address and other network params first, |
| * search for CONFIG_ETHADDR,CONFIG_SERVERIP,etc in this file |
| */ |
| |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| /* High Level Configuration Options */ |
| #define CONFIG_BOOKE 1 /* BOOKE */ |
| #define CONFIG_E500 1 /* BOOKE e500 family */ |
| #define CONFIG_MPC85xx 1 /* MPC8540/MPC8560 */ |
| #define CONFIG_CPM2 1 /* has CPM2 */ |
| #define CONFIG_STXGP3 1 /* Silicon Tx GPPP board specific*/ |
| |
| #undef CONFIG_PCI /* pci ethernet support */ |
| #define CONFIG_TSEC_ENET /* tsec ethernet support*/ |
| #undef CONFIG_ETHER_ON_FCC /* cpm FCC ethernet support */ |
| #define CONFIG_ENV_OVERWRITE |
| #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */ |
| #undef CONFIG_DDR_ECC /* only for ECC DDR module */ |
| #define CONFIG_DDR_DLL /* possible DLL fix needed */ |
| #define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */ |
| |
| |
| /* sysclk for MPC85xx |
| */ |
| |
| #define CONFIG_SYS_CLK_FREQ 33333333 /* most pci cards are 33Mhz */ |
| |
| /* Blinkin' LEDs for Robert :-) |
| */ |
| #define CONFIG_SHOW_ACTIVITY 1 |
| |
| /* |
| * These can be toggled for performance analysis, otherwise use default. |
| */ |
| #define CONFIG_L2_CACHE /* toggle L2 cache */ |
| #define CONFIG_BTB /* toggle branch predition */ |
| #define CONFIG_ADDR_STREAMING /* toggle addr streaming */ |
| |
| #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ |
| |
| #undef CFG_DRAM_TEST /* memory test, takes time */ |
| #define CFG_MEMTEST_START 0x00200000 /* memtest region */ |
| #define CFG_MEMTEST_END 0x00400000 |
| |
| |
| /* Localbus SDRAM is an option, not all boards have it. |
| * This address, however, is used to configure a 256M local bus |
| * window that includes the Config latch below. |
| */ |
| #define CFG_LBC_SDRAM_BASE 0xf0000000 /* Localbus SDRAM */ |
| #define CFG_LBC_SDRAM_SIZE 256 /* LBC SDRAM is 64MB */ |
| |
| #define CFG_FLASH_BASE 0xff000000 /* start of FLASH 16M */ |
| #define CFG_BR0_PRELIM 0xff001801 /* port size 32bit */ |
| |
| #define CFG_OR0_PRELIM 0xff000ff7 /* 16 MB Flash */ |
| #define CFG_MAX_FLASH_BANKS 1 /* number of banks */ |
| #define CFG_MAX_FLASH_SECT 136 /* sectors per device */ |
| #undef CFG_FLASH_CHECKSUM |
| #define CFG_FLASH_ERASE_TOUT 60000 /* Timeout for Flash Erase (in ms) */ |
| #define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ |
| |
| /* The configuration latch is Chip Select 1. |
| * It's an 8-bit latch in the lower 8 bits of the word. |
| */ |
| #define CFG_BR1_PRELIM 0xfc001801 /* 32-bit port */ |
| #define CFG_OR1_PRELIM 0xffff0ff7 /* 64K is enough */ |
| #define CFG_LBC_LCLDEVS_BASE 0xfc000000 /* Base of localbus devices */ |
| |
| #define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */ |
| |
| #if (CFG_MONITOR_BASE < CFG_FLASH_BASE) |
| #define CFG_RAMBOOT |
| #else |
| #undef CFG_RAMBOOT |
| #endif |
| |
| #ifdef CFG_RAMBOOT |
| #define CFG_CCSRBAR_DEFAULT 0x40000000 /* CCSRBAR by BDI cfg */ |
| #else |
| #define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ |
| #endif |
| #define CFG_CCSRBAR 0xfdf00000 /* relocated CCSRBAR */ |
| #define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */ |
| |
| |
| /* |
| * DDR Setup |
| */ |
| |
| /* |
| * Base addresses -- Note these are effective addresses where the |
| * actual resources get mapped (not physical addresses) |
| */ |
| #define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory */ |
| #define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE |
| |
| #define SPD_EEPROM_ADDRESS 0x54 /* DDR DIMM */ |
| |
| #undef CONFIG_CLOCKS_IN_MHZ |
| |
| /* local bus definitions */ |
| #define CFG_BR2_PRELIM 0xf8001861 /* 64MB localbus SDRAM */ |
| #define CFG_OR2_PRELIM 0xfc006901 |
| #define CFG_LBC_LCRR 0x00030004 /* local bus freq */ |
| #define CFG_LBC_LBCR 0x00000000 |
| #define CFG_LBC_LSRT 0x20000000 |
| #define CFG_LBC_MRTPR 0x20000000 |
| #define CFG_LBC_LSDMR_1 0x2861b723 |
| #define CFG_LBC_LSDMR_2 0x0861b723 |
| #define CFG_LBC_LSDMR_3 0x0861b723 |
| #define CFG_LBC_LSDMR_4 0x1861b723 |
| #define CFG_LBC_LSDMR_5 0x4061b723 |
| |
| #define CONFIG_L1_INIT_RAM |
| #define CFG_INIT_RAM_LOCK 1 |
| #define CFG_INIT_RAM_ADDR 0x60000000 /* Initial RAM address */ |
| #define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */ |
| |
| #define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */ |
| #define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) |
| #define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET |
| |
| #define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ |
| #define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ |
| |
| /* Serial Port */ |
| #define CONFIG_CONS_ON_SCC /* define if console on SCC */ |
| #undef CONFIG_CONS_NONE /* define if console on something else */ |
| #define CONFIG_CONS_INDEX 2 /* which serial channel for console */ |
| |
| #define CONFIG_BAUDRATE 38400 |
| |
| #define CFG_BAUDRATE_TABLE \ |
| {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} |
| |
| /* Use the HUSH parser */ |
| #define CFG_HUSH_PARSER |
| #ifdef CFG_HUSH_PARSER |
| #define CFG_PROMPT_HUSH_PS2 "> " |
| #endif |
| |
| /* |
| * I2C |
| */ |
| #define CONFIG_FSL_I2C /* Use FSL common I2C driver */ |
| #define CONFIG_HARD_I2C /* I2C with hardware support*/ |
| #undef CONFIG_SOFT_I2C /* I2C bit-banged */ |
| #define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ |
| #define CFG_I2C_SLAVE 0x7F |
| #if 0 |
| #define CFG_I2C_NOPROBES {0x00} /* Don't probe these addrs */ |
| #else |
| /* I did the 'if 0' so we could keep the syntax above if ever needed. */ |
| #undef CFG_I2C_NOPROBES |
| #endif |
| #define CFG_I2C_OFFSET 0x3000 |
| |
| /* RapdIO Map configuration, mapped 1:1. |
| */ |
| #define CFG_RIO_MEM_BASE 0xc0000000 |
| #define CFG_RIO_MEM_PHYS CFG_RIO_MEM_BASE |
| #define CFG_RIO_MEM_SIZE 0x200000000 /* 512 M */ |
| |
| /* Standard 8560 PCI addressing, mapped 1:1. |
| */ |
| #define CFG_PCI1_MEM_BASE 0x80000000 |
| #define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE |
| #define CFG_PCI1_MEM_SIZE 0x20000000 /* 512M */ |
| #define CFG_PCI1_IO_BASE 0xe2000000 |
| #define CFG_PCI1_IO_PHYS CFG_PCI1_IO_BASE |
| #define CFG_PCI1_IO_SIZE 0x01000000 /* 16 M */ |
| |
| #if defined(CONFIG_PCI) /* PCI Ethernet card */ |
| |
| #define CONFIG_NET_MULTI |
| #define CONFIG_PCI_PNP /* do pci plug-and-play */ |
| |
| #undef CONFIG_EEPRO100 |
| #undef CONFIG_TULIP |
| |
| #if !defined(CONFIG_PCI_PNP) |
| #define PCI_ENET0_IOADDR 0xe0000000 |
| #define PCI_ENET0_MEMADDR 0xe0000000 |
| #define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */ |
| #endif |
| |
| #undef CONFIG_PCI_SCAN_SHOW |
| #define CFG_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */ |
| |
| #endif /* CONFIG_PCI */ |
| |
| #if defined(CONFIG_TSEC_ENET) |
| |
| #ifndef CONFIG_NET_MULTI |
| #define CONFIG_NET_MULTI 1 |
| #endif |
| |
| #define CONFIG_MII 1 /* MII PHY management */ |
| |
| #define CONFIG_TSEC1 1 |
| #define CONFIG_TSEC1_NAME "TSEC0" |
| #define CONFIG_TSEC2 1 |
| #define CONFIG_TSEC2_NAME "TSEC1" |
| #undef CONFIG_MPS85XX_FEC |
| |
| #define TSEC1_PHY_ADDR 2 |
| #define TSEC2_PHY_ADDR 4 |
| #define TSEC1_PHYIDX 0 |
| #define TSEC2_PHYIDX 0 |
| #define CONFIG_ETHPRIME "TSEC0" |
| |
| #elif defined(CONFIG_ETHER_ON_FCC) /* CPM FCC Ethernet */ |
| |
| #define CONFIG_ETHER_ON_FCC2 /* define if ether on FCC */ |
| #undef CONFIG_ETHER_NONE /* define if ether on something else */ |
| #define CONFIG_ETHER_INDEX 2 /* which channel for ether */ |
| |
| #if (CONFIG_ETHER_INDEX == 2) |
| /* |
| * - Rx-CLK is CLK13 |
| * - Tx-CLK is CLK14 |
| * - Select bus for bd/buffers |
| * - Full duplex |
| */ |
| #define CFG_CMXFCR_MASK (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK) |
| #define CFG_CMXFCR_VALUE (CMXFCR_RF2CS_CLK13 | CMXFCR_TF2CS_CLK14) |
| #define CFG_CPMFCR_RAMTYPE 0 |
| #if 0 |
| #define CFG_FCC_PSMR (FCC_PSMR_FDE) |
| #else |
| #define CFG_FCC_PSMR 0 |
| #endif |
| #define FETH2_RST 0x01 |
| #elif (CONFIG_ETHER_INDEX == 3) |
| /* need more definitions here for FE3 */ |
| #define FETH3_RST 0x80 |
| #endif /* CONFIG_ETHER_INDEX */ |
| |
| /* MDIO is done through the TSEC0 control. |
| */ |
| #define CONFIG_MII /* MII PHY management */ |
| #undef CONFIG_BITBANGMII /* bit-bang MII PHY management */ |
| |
| #endif |
| |
| /* Environment */ |
| /* We use the top boot sector flash, so we have some 16K sectors for env |
| */ |
| #ifndef CFG_RAMBOOT |
| #define CFG_ENV_IS_IN_FLASH 1 |
| #define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x60000) |
| #define CFG_ENV_SECT_SIZE 0x4000 /* 16K (one top sector) for env */ |
| #define CFG_ENV_SIZE 0x2000 |
| #else |
| #define CFG_NO_FLASH 1 /* Flash is not usable now */ |
| #define CFG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */ |
| #define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000) |
| #define CFG_ENV_SIZE 0x2000 |
| #endif |
| |
| #define CONFIG_BOOTARGS "root=/dev/nfs rw ip=any console=ttyS1,38400" |
| #define CONFIG_BOOTCOMMAND "bootm 0xff000000 0xff100000" |
| #define CONFIG_BOOTDELAY 3 /* -1 disable autoboot */ |
| |
| #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ |
| #define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ |
| |
| /* |
| * Command line configuration. |
| */ |
| #include <config_cmd_default.h> |
| |
| #define CONFIG_CMD_PING |
| #define CONFIG_CMD_I2C |
| |
| #if defined(CFG_RAMBOOT) |
| #undef CONFIG_CMD_ENV |
| #undef CONFIG_CMD_LOADS |
| #else |
| #define CONFIG_CMD_ELF |
| #endif |
| |
| #if defined(CONFIG_PCI) |
| #define CONFIG_CMD_PCI |
| #endif |
| |
| #if defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC) |
| #define CONFIG_CMD_MII |
| #endif |
| |
| |
| #undef CONFIG_WATCHDOG /* watchdog disabled */ |
| |
| /* |
| * Miscellaneous configurable options |
| */ |
| #define CFG_LONGHELP /* undef to save memory */ |
| #define CFG_PROMPT "GPPP=> " /* Monitor Command Prompt */ |
| #if defined(CONFIG_CMD_KGDB) |
| #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ |
| #else |
| #define CFG_CBSIZE 256 /* Console I/O Buffer Size */ |
| #endif |
| #define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ |
| #define CFG_MAXARGS 16 /* max number of command args */ |
| #define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ |
| #define CFG_LOAD_ADDR 0x1000000 /* default load address */ |
| #define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ |
| |
| /* |
| * For booting Linux, the board info and command line data |
| * have to be in the first 8 MB of memory, since this is |
| * the maximum mapped by the Linux kernel during initialization. |
| */ |
| #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ |
| |
| /* Cache Configuration */ |
| #define CFG_DCACHE_SIZE 32768 |
| #define CFG_CACHELINE_SIZE 32 |
| #if defined(CONFIG_CMD_KGDB) |
| #define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ |
| #endif |
| |
| /* |
| * Internal Definitions |
| * |
| * Boot Flags |
| */ |
| #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ |
| #define BOOTFLAG_WARM 0x02 /* Software reboot */ |
| |
| #if defined(CONFIG_CMD_KGDB) |
| #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ |
| #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ |
| #endif |
| |
| /*Note: change below for your network setting!!! */ |
| #if defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC) |
| #define CONFIG_ETHADDR 00:e0:0c:07:9b:8a |
| #define CONFIG_HAS_ETH1 |
| #define CONFIG_ETH1ADDR 00:e0:0c:07:9b:8b |
| #define CONFIG_HAS_ETH2 |
| #define CONFIG_ETH2ADDR 00:e0:0c:07:9b:8c |
| #endif |
| |
| #define CONFIG_SERVERIP 192.168.85.1 |
| #define CONFIG_IPADDR 192.168.85.60 |
| #define CONFIG_GATEWAYIP 192.168.85.1 |
| #define CONFIG_NETMASK 255.255.255.0 |
| #define CONFIG_HOSTNAME STX_GP3 |
| #define CONFIG_ROOTPATH /gppproot |
| #define CONFIG_BOOTFILE uImage |
| #define CONFIG_LOADADDR 0x1000000 |
| |
| #endif /* __CONFIG_H */ |