| /* |
| * (C) Copyright 2001-2003 |
| * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| /* |
| * board/config.h - configuration options, board specific |
| */ |
| |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| /* |
| * High Level Configuration Options |
| * (easy to change) |
| */ |
| |
| #define CONFIG_405EP 1 /* This is a PPC405 CPU */ |
| #define CONFIG_PLU405 1 /* ...on a PLU405 board */ |
| |
| #define CONFIG_SYS_TEXT_BASE 0xFFF80000 |
| #define CONFIG_DISPLAY_BOARDINFO |
| |
| #define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */ |
| #define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */ |
| |
| #define CONFIG_SYS_CLK_FREQ 33333400 /* external frequency to pll */ |
| |
| #define CONFIG_BAUDRATE 9600 |
| |
| #undef CONFIG_BOOTARGS |
| #undef CONFIG_BOOTCOMMAND |
| |
| #define CONFIG_PREBOOT /* enable preboot variable */ |
| |
| #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ |
| |
| #undef CONFIG_HAS_ETH1 |
| |
| #define CONFIG_PPC4xx_EMAC |
| #define CONFIG_MII 1 /* MII PHY management */ |
| #define CONFIG_PHY_ADDR 0 /* PHY address */ |
| #define CONFIG_LXT971_NO_SLEEP 1 /* disable sleep mode in LXT971 */ |
| #define CONFIG_RESET_PHY_R 1 /* use reset_phy() */ |
| |
| #define CONFIG_PHY_CLK_FREQ EMAC_STACR_CLK_66MHZ /* 66 MHz OPB clock*/ |
| |
| /* |
| * BOOTP options |
| */ |
| #define CONFIG_BOOTP_BOOTFILESIZE |
| #define CONFIG_BOOTP_BOOTPATH |
| #define CONFIG_BOOTP_GATEWAY |
| #define CONFIG_BOOTP_HOSTNAME |
| |
| /* |
| * Command line configuration. |
| */ |
| #define CONFIG_CMD_PCI |
| #define CONFIG_CMD_IRQ |
| #define CONFIG_CMD_IDE |
| #define CONFIG_CMD_NAND |
| #define CONFIG_CMD_DATE |
| #define CONFIG_CMD_EEPROM |
| |
| #define CONFIG_MAC_PARTITION |
| #define CONFIG_DOS_PARTITION |
| |
| #define CONFIG_SUPPORT_VFAT |
| |
| #undef CONFIG_WATCHDOG /* watchdog disabled */ |
| |
| #define CONFIG_RTC_MC146818 /* DS1685 is MC146818 compatible*/ |
| #define CONFIG_SYS_RTC_REG_BASE_ADDR 0xF0000500 /* RTC Base Address */ |
| |
| #define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */ |
| |
| /* |
| * Miscellaneous configurable options |
| */ |
| #define CONFIG_SYS_LONGHELP /* undef to save memory */ |
| |
| #if defined(CONFIG_CMD_KGDB) |
| #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ |
| #else |
| #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ |
| #endif |
| #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ |
| #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ |
| #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ |
| |
| #define CONFIG_SYS_DEVICE_NULLDEV 1 /* include nulldev device */ |
| |
| #define CONFIG_SYS_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/ |
| |
| #define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */ |
| |
| #define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ |
| #define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ |
| |
| #define CONFIG_CONS_INDEX 1 /* Use UART0 */ |
| #define CONFIG_SYS_NS16550_SERIAL |
| #define CONFIG_SYS_NS16550_REG_SIZE 1 |
| #define CONFIG_SYS_NS16550_CLK get_serial_clock() |
| |
| #undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no external serial clock used */ |
| #define CONFIG_SYS_BASE_BAUD 691200 |
| |
| /* The following table includes the supported baudrates */ |
| #define CONFIG_SYS_BAUDRATE_TABLE \ |
| { 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \ |
| 57600, 115200, 230400, 460800, 921600 } |
| |
| #define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ |
| #define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */ |
| |
| #define CONFIG_CMDLINE_EDITING 1 /* add command line history */ |
| #define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ |
| |
| #define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ |
| |
| #define CONFIG_SYS_RX_ETH_BUFFER 16 /* use 16 rx buffer on 405 emac */ |
| |
| /* |
| * NAND-FLASH stuff |
| */ |
| #define CONFIG_SYS_NAND_BASE_LIST {CONFIG_SYS_NAND_BASE} |
| #define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND devices */ |
| #define NAND_BIG_DELAY_US 25 |
| |
| #define CONFIG_SYS_NAND_CE (0x80000000 >> 1) /* our CE is GPIO1 */ |
| #define CONFIG_SYS_NAND_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */ |
| #define CONFIG_SYS_NAND_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */ |
| #define CONFIG_SYS_NAND_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */ |
| |
| #define CONFIG_SYS_NAND_SKIP_BAD_DOT_I 1 /* ".i" read skips bad blocks */ |
| #define CONFIG_SYS_NAND_QUIET 1 |
| |
| /* |
| * PCI stuff |
| */ |
| #define PCI_HOST_ADAPTER 0 /* configure as pci adapter */ |
| #define PCI_HOST_FORCE 1 /* configure as pci host */ |
| #define PCI_HOST_AUTO 2 /* detected via arbiter enable */ |
| |
| #define CONFIG_PCI /* include pci support */ |
| #define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */ |
| #define CONFIG_PCI_HOST PCI_HOST_FORCE /* select pci host function */ |
| #define CONFIG_PCI_PNP /* do pci plug-and-play */ |
| /* resource configuration */ |
| |
| #define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */ |
| |
| #define CONFIG_PCI_CONFIG_HOST_BRIDGE 1 /* don't skip host bridge config*/ |
| |
| #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */ |
| #define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0405 /* PCI Device ID: CPCI-405 */ |
| #define CONFIG_SYS_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/ |
| #define CONFIG_SYS_PCI_PTM1LA 0x00000000 /* point to sdram */ |
| #define CONFIG_SYS_PCI_PTM1MS 0xf8000001 /* 128MB, enable hard-wired to 1 */ |
| #define CONFIG_SYS_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */ |
| #define CONFIG_SYS_PCI_PTM2LA 0xffc00000 /* point to flash */ |
| #define CONFIG_SYS_PCI_PTM2MS 0xffc00001 /* 4MB, enable */ |
| #define CONFIG_SYS_PCI_PTM2PCI 0x08000000 /* Host: use this pci address */ |
| |
| /* |
| * IDE/ATA stuff |
| */ |
| #undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */ |
| #undef CONFIG_IDE_LED /* no led for ide supported */ |
| #define CONFIG_IDE_RESET 1 /* reset for ide supported */ |
| |
| #define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE busses */ |
| /* max. 1 drives per IDE bus */ |
| #define CONFIG_SYS_IDE_MAXDEVICE (CONFIG_SYS_IDE_MAXBUS*1) |
| |
| #define CONFIG_SYS_ATA_BASE_ADDR 0xF0100000 |
| #define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 |
| |
| #define CONFIG_SYS_ATA_DATA_OFFSET 0x0000 /* Offset for data I/O */ |
| #define CONFIG_SYS_ATA_REG_OFFSET 0x0000 /* Offset for normal register access */ |
| #define CONFIG_SYS_ATA_ALT_OFFSET 0x0000 /* Offset for alternate registers */ |
| |
| /* |
| * For booting Linux, the board info and command line data |
| * have to be in the first 8 MB of memory, since this is |
| * the maximum mapped by the Linux kernel during initialization. |
| */ |
| #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ |
| |
| /* |
| * FLASH organization |
| */ |
| #define FLASH_BASE0_PRELIM 0xFFC00000 /* FLASH bank #0 */ |
| |
| #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ |
| #define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sectors on one chip */ |
| |
| #define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ |
| #define CONFIG_SYS_FLASH_WRITE_TOUT 1000 /* Timeout for Flash Write (in ms) */ |
| |
| #define CONFIG_SYS_FLASH_WORD_SIZE unsigned short /* flash word size (width) */ |
| #define CONFIG_SYS_FLASH_ADDR0 0x5555 /* 1st addr for flash config cycles */ |
| #define CONFIG_SYS_FLASH_ADDR1 0x2AAA /* 2nd addr for flash config cycles */ |
| /* |
| * The following defines are added for buggy IOP480 byte interface. |
| * All other boards should use the standard values (CPCI405 etc.) |
| */ |
| #define CONFIG_SYS_FLASH_READ0 0x0000 /* 0 is standard */ |
| #define CONFIG_SYS_FLASH_READ1 0x0001 /* 1 is standard */ |
| #define CONFIG_SYS_FLASH_READ2 0x0002 /* 2 is standard */ |
| |
| #define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector */ |
| |
| /* |
| * Start addresses for the final memory configuration |
| * (Set up by the startup code) |
| * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 |
| */ |
| #define CONFIG_SYS_SDRAM_BASE 0x00000000 |
| #define CONFIG_SYS_FLASH_BASE CONFIG_SYS_MONITOR_BASE |
| #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE |
| #define CONFIG_SYS_MONITOR_LEN (~(CONFIG_SYS_TEXT_BASE) + 1) |
| #define CONFIG_SYS_MALLOC_LEN (1024 << 10) |
| |
| /* |
| * Environment Variable setup |
| */ |
| #define CONFIG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */ |
| #define CONFIG_ENV_OFFSET 0x100 /* reseve 0x100 bytes for strapping */ |
| #define CONFIG_ENV_SIZE 0x700 |
| |
| /* |
| * I2C EEPROM (24WC16) for environment |
| */ |
| #define CONFIG_SYS_I2C |
| #define CONFIG_SYS_I2C_PPC4XX |
| #define CONFIG_SYS_I2C_PPC4XX_CH0 |
| #define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 |
| #define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F |
| |
| #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM 24WC16 */ |
| #define CONFIG_SYS_EEPROM_WREN 1 |
| |
| /* 24WC16 */ |
| #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ |
| /* mask of address bits that overflow into the "EEPROM chip address" */ |
| #define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07 |
| #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 /* The 24WC16 has */ |
| /* 16 byte page write mode using */ |
| /* last 4 bits of the address */ |
| #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ |
| |
| /* |
| * External Bus Controller (EBC) Setup |
| */ |
| #define CAN0_BA 0xF0000000 /* CAN0 Base Address */ |
| #define CAN1_BA 0xF0000100 /* CAN1 Base Address */ |
| #define DUART0_BA 0xF0000400 /* DUART Base Address */ |
| #define DUART1_BA 0xF0000408 /* DUART Base Address */ |
| #define RTC_BA 0xF0000500 /* RTC Base Address */ |
| #define VGA_BA 0xF1000000 /* Epson VGA Base Address */ |
| #define CONFIG_SYS_NAND_BASE 0xF4000000 /* NAND FLASH Base Address */ |
| |
| /* Memory Bank 0 (Flash Bank 0, NOR-FLASH) initialization */ |
| /* TWT=16,CSN=1,OEN=1,WBN=1,WBF=1,TH=4,SOR=1 */ |
| #define CONFIG_SYS_EBC_PB0AP 0x92015480 |
| /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */ |
| #define CONFIG_SYS_EBC_PB0CR 0xFFC5A000 |
| |
| /* Memory Bank 1 (Flash Bank 1, NAND-FLASH) initialization */ |
| #define CONFIG_SYS_EBC_PB1AP 0x92015480 |
| /* BAS=0xF40,BS=1MB,BU=R/W,BW=8bit */ |
| #define CONFIG_SYS_EBC_PB1CR 0xF4018000 |
| |
| /* Memory Bank 2 (8 Bit Peripheral: CAN, UART, RTC) initialization */ |
| /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */ |
| #define CONFIG_SYS_EBC_PB2AP 0x010053C0 |
| /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */ |
| #define CONFIG_SYS_EBC_PB2CR 0xF0018000 |
| |
| /* Memory Bank 3 (16 Bit Peripheral: FPGA internal, dig. IO) initialization */ |
| /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */ |
| #define CONFIG_SYS_EBC_PB3AP 0x010053C0 |
| /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */ |
| #define CONFIG_SYS_EBC_PB3CR 0xF011A000 |
| |
| /* |
| * FPGA stuff |
| */ |
| #define CONFIG_SYS_FPGA_BASE_ADDR 0xF0100100 /* FPGA internal Base Address */ |
| |
| /* FPGA internal regs */ |
| #define CONFIG_SYS_FPGA_CTRL 0x000 |
| |
| /* FPGA Control Reg */ |
| #define CONFIG_SYS_FPGA_CTRL_CF_RESET 0x0001 |
| #define CONFIG_SYS_FPGA_CTRL_WDI 0x0002 |
| #define CONFIG_SYS_FPGA_CTRL_PS2_RESET 0x0020 |
| |
| #define CONFIG_SYS_FPGA_SPARTAN2 1 /* using Xilinx Spartan 2 now */ |
| #define CONFIG_SYS_FPGA_MAX_SIZE 128*1024 /* 128kByte is enough for XC2S50E*/ |
| |
| /* FPGA program pin configuration */ |
| #define CONFIG_SYS_FPGA_PRG 0x04000000 /* FPGA program pin (ppc output) */ |
| #define CONFIG_SYS_FPGA_CLK 0x02000000 /* FPGA clk pin (ppc output) */ |
| #define CONFIG_SYS_FPGA_DATA 0x01000000 /* FPGA data pin (ppc output) */ |
| #define CONFIG_SYS_FPGA_INIT 0x00010000 /* FPGA init pin (ppc input) */ |
| #define CONFIG_SYS_FPGA_DONE 0x00008000 /* FPGA done pin (ppc input) */ |
| |
| /* |
| * Definitions for initial stack pointer and data area (in data cache) |
| */ |
| /* use on chip memory ( OCM ) for temperary stack until sdram is tested */ |
| #define CONFIG_SYS_TEMP_STACK_OCM 1 |
| |
| /* On Chip Memory location */ |
| #define CONFIG_SYS_OCM_DATA_ADDR 0xF8000000 |
| #define CONFIG_SYS_OCM_DATA_SIZE 0x1000 |
| #define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* inside of SDRAM */ |
| #define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SYS_OCM_DATA_SIZE /* Size of used area in RAM */ |
| |
| #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) |
| #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET |
| |
| /* |
| * Definitions for GPIO setup (PPC405EP specific) |
| * |
| * GPIO0[0] - External Bus Controller BLAST output |
| * GPIO0[1-9] - Instruction trace outputs -> GPIO |
| * GPIO0[10-13] - External Bus Controller CS_1 - CS_4 outputs |
| * GPIO0[14-16] - External Bus Controller ABUS3-ABUS5 outputs -> GPIO |
| * GPIO0[17-23] - External Interrupts IRQ0 - IRQ6 inputs |
| * GPIO0[24-27] - UART0 control signal inputs/outputs |
| * GPIO0[28-29] - UART1 data signal input/output |
| * GPIO0[30-31] - EMAC0 and EMAC1 reject packet inputs |
| */ |
| #define CONFIG_SYS_GPIO0_OSRL 0x00000550 |
| #define CONFIG_SYS_GPIO0_OSRH 0x00000110 |
| #define CONFIG_SYS_GPIO0_ISR1L 0x00000000 |
| #define CONFIG_SYS_GPIO0_ISR1H 0x15555445 |
| #define CONFIG_SYS_GPIO0_TSRL 0x00000000 |
| #define CONFIG_SYS_GPIO0_TSRH 0x00000000 |
| #define CONFIG_SYS_GPIO0_TCR 0x77FE0014 |
| |
| #define CONFIG_SYS_DUART_RST (0x80000000 >> 14) |
| #define CONFIG_SYS_EEPROM_WP (0x80000000 >> 0) |
| |
| /* |
| * Default speed selection (cpu_plb_opb_ebc) in MHz. |
| * This value will be set if iic boot eprom is disabled. |
| */ |
| #if 1 |
| #define PLLMR0_DEFAULT PLLMR0_266_133_66_33 |
| #define PLLMR1_DEFAULT PLLMR1_266_133_66_33 |
| #endif |
| #if 0 |
| #define PLLMR0_DEFAULT PLLMR0_200_100_50_33 |
| #define PLLMR1_DEFAULT PLLMR1_200_100_50_33 |
| #endif |
| #if 0 |
| #define PLLMR0_DEFAULT PLLMR0_133_66_66_33 |
| #define PLLMR1_DEFAULT PLLMR1_133_66_66_33 |
| #endif |
| |
| /* |
| * PCI OHCI controller |
| */ |
| #define CONFIG_USB_OHCI_NEW 1 |
| #define CONFIG_PCI_OHCI 1 |
| #define CONFIG_SYS_OHCI_SWAP_REG_ACCESS 1 |
| #define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15 |
| #define CONFIG_SYS_USB_OHCI_SLOT_NAME "ohci_pci" |
| #define CONFIG_USB_STORAGE 1 |
| |
| /* |
| * UBI |
| */ |
| #define CONFIG_CMD_UBI |
| #define CONFIG_RBTREE |
| #define CONFIG_MTD_DEVICE |
| #define CONFIG_MTD_PARTITIONS |
| #define CONFIG_CMD_MTDPARTS |
| #define CONFIG_LZO |
| |
| #endif /* __CONFIG_H */ |