Gitiles
Code Review Sign In
git01.mediatek.com / filogic / uboot / e8dc17be6d844e764bcad0bdb434d6852b104535 / . / arch / powerpc / cpu / mpc8xxx / ddr / ctrl_regs.c
blob: 5938c44cec1c5f5ff38aaf3d77f1a9feaa651055 [file] [log] [blame]
/*
* Copyright 2008-2012 Freescale Semiconductor, Inc.
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the Free
* Software Foundation; either version 2 of the License, or (at your option)
* any later version.
*/
/*
* Generic driver for Freescale DDR/DDR2/DDR3 memory controller.
* Based on code from spd_sdram.c
* Author: James Yang [at freescale.com]
*/
#include <common.h>
#include <asm/fsl_ddr_sdram.h>
#include "ddr.h"
#ifdef CONFIG_MPC83xx
#define _DDR_ADDR CONFIG_SYS_MPC83xx_DDR_ADDR
#elif defined(CONFIG_MPC85xx)
#define _DDR_ADDR CONFIG_SYS_MPC85xx_DDR_ADDR
#elif defined(CONFIG_MPC86xx)
#define _DDR_ADDR CONFIG_SYS_MPC86xx_DDR_ADDR
#else
#error "Undefined _DDR_ADDR"
#endif
u32 fsl_ddr_get_version(void)
{
ccsr_ddr_t *ddr;
u32 ver_major_minor_errata;
ddr = (void *)_DDR_ADDR;
ver_major_minor_errata = (in_be32(&ddr->ip_rev1) & 0xFFFF) << 8;
ver_major_minor_errata |= (in_be32(&ddr->ip_rev2) & 0xFF00) >> 8;
return ver_major_minor_errata;
}
unsigned int picos_to_mclk(unsigned int picos);
/*
* Determine Rtt value.
*
* This should likely be either board or controller specific.
*
* Rtt(nominal) - DDR2:
* 0 = Rtt disabled
* 1 = 75 ohm
* 2 = 150 ohm
* 3 = 50 ohm
* Rtt(nominal) - DDR3:
* 0 = Rtt disabled
* 1 = 60 ohm
* 2 = 120 ohm
* 3 = 40 ohm
* 4 = 20 ohm
* 5 = 30 ohm
*
* FIXME: Apparently 8641 needs a value of 2
* FIXME: Old code seys if 667 MHz or higher, use 3 on 8572
*
* FIXME: There was some effort down this line earlier:
*
* unsigned int i;
* for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL/2; i++) {
* if (popts->dimmslot[i].num_valid_cs
* && (popts->cs_local_opts[2*i].odt_rd_cfg
* || popts->cs_local_opts[2*i].odt_wr_cfg)) {
* rtt = 2;
* break;
* }
* }
*/
static inline int fsl_ddr_get_rtt(void)
{
int rtt;
#if defined(CONFIG_FSL_DDR1)
rtt = 0;
#elif defined(CONFIG_FSL_DDR2)
rtt = 3;
#else
rtt = 0;
#endif
return rtt;
}
/*
* compute the CAS write latency according to DDR3 spec
* CWL = 5 if tCK >= 2.5ns
* 6 if 2.5ns > tCK >= 1.875ns
* 7 if 1.875ns > tCK >= 1.5ns
* 8 if 1.5ns > tCK >= 1.25ns
* 9 if 1.25ns > tCK >= 1.07ns
* 10 if 1.07ns > tCK >= 0.935ns
* 11 if 0.935ns > tCK >= 0.833ns
* 12 if 0.833ns > tCK >= 0.75ns
*/
static inline unsigned int compute_cas_write_latency(void)
{
unsigned int cwl;
const unsigned int mclk_ps = get_memory_clk_period_ps();
if (mclk_ps >= 2500)
cwl = 5;
else if (mclk_ps >= 1875)
cwl = 6;
else if (mclk_ps >= 1500)
cwl = 7;
else if (mclk_ps >= 1250)
cwl = 8;
else if (mclk_ps >= 1070)
cwl = 9;
else if (mclk_ps >= 935)
cwl = 10;
else if (mclk_ps >= 833)
cwl = 11;
else if (mclk_ps >= 750)
cwl = 12;
else {
cwl = 12;
printf("Warning: CWL is out of range\n");
}
return cwl;
}
/* Chip Select Configuration (CSn_CONFIG) */
static void set_csn_config(int dimm_number, int i, fsl_ddr_cfg_regs_t *ddr,
const memctl_options_t *popts,
const dimm_params_t *dimm_params)
{
unsigned int cs_n_en = 0; /* Chip Select enable */
unsigned int intlv_en = 0; /* Memory controller interleave enable */
unsigned int intlv_ctl = 0; /* Interleaving control */
unsigned int ap_n_en = 0; /* Chip select n auto-precharge enable */
unsigned int odt_rd_cfg = 0; /* ODT for reads configuration */
unsigned int odt_wr_cfg = 0; /* ODT for writes configuration */
unsigned int ba_bits_cs_n = 0; /* Num of bank bits for SDRAM on CSn */
unsigned int row_bits_cs_n = 0; /* Num of row bits for SDRAM on CSn */
unsigned int col_bits_cs_n = 0; /* Num of ocl bits for SDRAM on CSn */
int go_config = 0;
/* Compute CS_CONFIG only for existing ranks of each DIMM. */
switch (i) {
case 0:
if (dimm_params[dimm_number].n_ranks > 0) {
go_config = 1;
/* These fields only available in CS0_CONFIG */
if (!popts->memctl_interleaving)
break;
switch (popts->memctl_interleaving_mode) {
case FSL_DDR_CACHE_LINE_INTERLEAVING:
case FSL_DDR_PAGE_INTERLEAVING:
case FSL_DDR_BANK_INTERLEAVING:
case FSL_DDR_SUPERBANK_INTERLEAVING:
intlv_en = popts->memctl_interleaving;
intlv_ctl = popts->memctl_interleaving_mode;
break;
default:
break;
}
}
break;
case 1:
if ((dimm_number == 0 && dimm_params[0].n_ranks > 1) || \
(dimm_number == 1 && dimm_params[1].n_ranks > 0))
go_config = 1;
break;
case 2:
if ((dimm_number == 0 && dimm_params[0].n_ranks > 2) || \
(dimm_number >= 1 && dimm_params[dimm_number].n_ranks > 0))
go_config = 1;
break;
case 3:
if ((dimm_number == 0 && dimm_params[0].n_ranks > 3) || \
(dimm_number == 1 && dimm_params[1].n_ranks > 1) || \
(dimm_number == 3 && dimm_params[3].n_ranks > 0))
go_config = 1;
break;
default:
break;
}
if (go_config) {
unsigned int n_banks_per_sdram_device;
cs_n_en = 1;
ap_n_en = popts->cs_local_opts[i].auto_precharge;
odt_rd_cfg = popts->cs_local_opts[i].odt_rd_cfg;
odt_wr_cfg = popts->cs_local_opts[i].odt_wr_cfg;
n_banks_per_sdram_device
= dimm_params[dimm_number].n_banks_per_sdram_device;
ba_bits_cs_n = __ilog2(n_banks_per_sdram_device) - 2;
row_bits_cs_n = dimm_params[dimm_number].n_row_addr - 12;
col_bits_cs_n = dimm_params[dimm_number].n_col_addr - 8;
}
ddr->cs[i].config = (0
| ((cs_n_en & 0x1) << 31)
| ((intlv_en & 0x3) << 29)
| ((intlv_ctl & 0xf) << 24)
| ((ap_n_en & 0x1) << 23)
/* XXX: some implementation only have 1 bit starting at left */
| ((odt_rd_cfg & 0x7) << 20)
/* XXX: Some implementation only have 1 bit starting at left */
| ((odt_wr_cfg & 0x7) << 16)
| ((ba_bits_cs_n & 0x3) << 14)
| ((row_bits_cs_n & 0x7) << 8)
| ((col_bits_cs_n & 0x7) << 0)
);
debug("FSLDDR: cs[%d]_config = 0x%08x\n", i,ddr->cs[i].config);
}
/* Chip Select Configuration 2 (CSn_CONFIG_2) */
/* FIXME: 8572 */
static void set_csn_config_2(int i, fsl_ddr_cfg_regs_t *ddr)
{
unsigned int pasr_cfg = 0; /* Partial array self refresh config */
ddr->cs[i].config_2 = ((pasr_cfg & 7) << 24);
debug("FSLDDR: cs[%d]_config_2 = 0x%08x\n", i, ddr->cs[i].config_2);
}
/* -3E = 667 CL5, -25 = CL6 800, -25E = CL5 800 */
#if !defined(CONFIG_FSL_DDR1)
/*
* DDR SDRAM Timing Configuration 0 (TIMING_CFG_0)
*
* Avoid writing for DDR I. The new PQ38 DDR controller
* dreams up non-zero default values to be backwards compatible.
*/
static void set_timing_cfg_0(fsl_ddr_cfg_regs_t *ddr,
const memctl_options_t *popts)
{
unsigned char trwt_mclk = 0; /* Read-to-write turnaround */
unsigned char twrt_mclk = 0; /* Write-to-read turnaround */
/* 7.5 ns on -3E; 0 means WL - CL + BL/2 + 1 */
unsigned char trrt_mclk = 0; /* Read-to-read turnaround */
unsigned char twwt_mclk = 0; /* Write-to-write turnaround */
/* Active powerdown exit timing (tXARD and tXARDS). */
unsigned char act_pd_exit_mclk;
/* Precharge powerdown exit timing (tXP). */
unsigned char pre_pd_exit_mclk;
/* ODT powerdown exit timing (tAXPD). */
unsigned char taxpd_mclk;
/* Mode register set cycle time (tMRD). */
unsigned char tmrd_mclk;
#ifdef CONFIG_FSL_DDR3
/*
* (tXARD and tXARDS). Empirical?
* The DDR3 spec has not tXARD,
* we use the tXP instead of it.
* tXP=max(3nCK, 7.5ns) for DDR3.
* spec has not the tAXPD, we use
* tAXPD=1, need design to confirm.
*/
int tXP = max((get_memory_clk_period_ps() * 3), 7500); /* unit=ps */
unsigned int data_rate = get_ddr_freq(0);
tmrd_mclk = 4;
/* set the turnaround time */
trwt_mclk = 1;
if ((data_rate/1000000 > 1150) || (popts->memctl_interleaving))
twrt_mclk = 1;
if (popts->dynamic_power == 0) { /* powerdown is not used */
act_pd_exit_mclk = 1;
pre_pd_exit_mclk = 1;
taxpd_mclk = 1;
} else {
/* act_pd_exit_mclk = tXARD, see above */
act_pd_exit_mclk = picos_to_mclk(tXP);
/* Mode register MR0[A12] is '1' - fast exit */
pre_pd_exit_mclk = act_pd_exit_mclk;
taxpd_mclk = 1;
}
#else /* CONFIG_FSL_DDR2 */
/*
* (tXARD and tXARDS). Empirical?
* tXARD = 2 for DDR2
* tXP=2
* tAXPD=8
*/
act_pd_exit_mclk = 2;
pre_pd_exit_mclk = 2;
taxpd_mclk = 8;
tmrd_mclk = 2;
#endif
if (popts->trwt_override)
trwt_mclk = popts->trwt;
ddr->timing_cfg_0 = (0
| ((trwt_mclk & 0x3) << 30) /* RWT */
| ((twrt_mclk & 0x3) << 28) /* WRT */
| ((trrt_mclk & 0x3) << 26) /* RRT */
| ((twwt_mclk & 0x3) << 24) /* WWT */
| ((act_pd_exit_mclk & 0x7) << 20) /* ACT_PD_EXIT */
| ((pre_pd_exit_mclk & 0xF) << 16) /* PRE_PD_EXIT */
| ((taxpd_mclk & 0xf) << 8) /* ODT_PD_EXIT */
| ((tmrd_mclk & 0xf) << 0) /* MRS_CYC */
);
debug("FSLDDR: timing_cfg_0 = 0x%08x\n", ddr->timing_cfg_0);
}
#endif /* defined(CONFIG_FSL_DDR2) */
/* DDR SDRAM Timing Configuration 3 (TIMING_CFG_3) */
static void set_timing_cfg_3(fsl_ddr_cfg_regs_t *ddr,
const common_timing_params_t *common_dimm,
unsigned int cas_latency)
{
/* Extended Activate to precharge interval (tRAS) */
unsigned int ext_acttopre = 0;
unsigned int ext_refrec; /* Extended refresh recovery time (tRFC) */
unsigned int ext_caslat = 0; /* Extended MCAS latency from READ cmd */
unsigned int cntl_adj = 0; /* Control Adjust */
/* If the tRAS > 19 MCLK, we use the ext mode */
if (picos_to_mclk(common_dimm->tRAS_ps) > 0x13)
ext_acttopre = 1;
ext_refrec = (picos_to_mclk(common_dimm->tRFC_ps) - 8) >> 4;
/* If the CAS latency more than 8, use the ext mode */
if (cas_latency > 8)
ext_caslat = 1;
ddr->timing_cfg_3 = (0
| ((ext_acttopre & 0x1) << 24)
| ((ext_refrec & 0xF) << 16)
| ((ext_caslat & 0x1) << 12)
| ((cntl_adj & 0x7) << 0)
);
debug("FSLDDR: timing_cfg_3 = 0x%08x\n", ddr->timing_cfg_3);
}
/* DDR SDRAM Timing Configuration 1 (TIMING_CFG_1) */
static void set_timing_cfg_1(fsl_ddr_cfg_regs_t *ddr,
const memctl_options_t *popts,
const common_timing_params_t *common_dimm,
unsigned int cas_latency)
{
/* Precharge-to-activate interval (tRP) */
unsigned char pretoact_mclk;
/* Activate to precharge interval (tRAS) */
unsigned char acttopre_mclk;
/* Activate to read/write interval (tRCD) */
unsigned char acttorw_mclk;
/* CASLAT */
unsigned char caslat_ctrl;
/* Refresh recovery time (tRFC) ; trfc_low */
unsigned char refrec_ctrl;
/* Last data to precharge minimum interval (tWR) */
unsigned char wrrec_mclk;
/* Activate-to-activate interval (tRRD) */
unsigned char acttoact_mclk;
/* Last write data pair to read command issue interval (tWTR) */
unsigned char wrtord_mclk;
/* DDR_SDRAM_MODE doesn't support 9,11,13,15 */
static const u8 wrrec_table[] = {
1, 2, 3, 4, 5, 6, 7, 8, 10, 10, 12, 12, 14, 14, 0, 0};
pretoact_mclk = picos_to_mclk(common_dimm->tRP_ps);
acttopre_mclk = picos_to_mclk(common_dimm->tRAS_ps);
acttorw_mclk = picos_to_mclk(common_dimm->tRCD_ps);
/*
* Translate CAS Latency to a DDR controller field value:
*
* CAS Lat DDR I DDR II Ctrl
* Clocks SPD Bit SPD Bit Value
* ------- ------- ------- -----
* 1.0 0 0001
* 1.5 1 0010
* 2.0 2 2 0011
* 2.5 3 0100
* 3.0 4 3 0101
* 3.5 5 0110
* 4.0 4 0111
* 4.5 1000
* 5.0 5 1001
*/
#if defined(CONFIG_FSL_DDR1)
caslat_ctrl = (cas_latency + 1) & 0x07;
#elif defined(CONFIG_FSL_DDR2)
caslat_ctrl = 2 * cas_latency - 1;
#else
/*
* if the CAS latency more than 8 cycle,
* we need set extend bit for it at
* TIMING_CFG_3[EXT_CASLAT]
*/
if (cas_latency > 8)
cas_latency -= 8;
caslat_ctrl = 2 * cas_latency - 1;
#endif
refrec_ctrl = picos_to_mclk(common_dimm->tRFC_ps) - 8;
wrrec_mclk = picos_to_mclk(common_dimm->tWR_ps);
wrrec_mclk = wrrec_table[wrrec_mclk - 1];
if (popts->OTF_burst_chop_en)
wrrec_mclk += 2;
acttoact_mclk = picos_to_mclk(common_dimm->tRRD_ps);
/*
* JEDEC has min requirement for tRRD
*/
#if defined(CONFIG_FSL_DDR3)
if (acttoact_mclk < 4)
acttoact_mclk = 4;
#endif
wrtord_mclk = picos_to_mclk(common_dimm->tWTR_ps);
/*
* JEDEC has some min requirements for tWTR
*/
#if defined(CONFIG_FSL_DDR2)
if (wrtord_mclk < 2)
wrtord_mclk = 2;
#elif defined(CONFIG_FSL_DDR3)
if (wrtord_mclk < 4)
wrtord_mclk = 4;
#endif
if (popts->OTF_burst_chop_en)
wrtord_mclk += 2;
ddr->timing_cfg_1 = (0
| ((pretoact_mclk & 0x0F) << 28)
| ((acttopre_mclk & 0x0F) << 24)
| ((acttorw_mclk & 0xF) << 20)
| ((caslat_ctrl & 0xF) << 16)
| ((refrec_ctrl & 0xF) << 12)
| ((wrrec_mclk & 0x0F) << 8)
| ((acttoact_mclk & 0x07) << 4)
| ((wrtord_mclk & 0x07) << 0)
);
debug("FSLDDR: timing_cfg_1 = 0x%08x\n", ddr->timing_cfg_1);
}
/* DDR SDRAM Timing Configuration 2 (TIMING_CFG_2) */
static void set_timing_cfg_2(fsl_ddr_cfg_regs_t *ddr,
const memctl_options_t *popts,
const common_timing_params_t *common_dimm,
unsigned int cas_latency,
unsigned int additive_latency)
{
/* Additive latency */
unsigned char add_lat_mclk;
/* CAS-to-preamble override */
unsigned short cpo;
/* Write latency */
unsigned char wr_lat;
/* Read to precharge (tRTP) */
unsigned char rd_to_pre;
/* Write command to write data strobe timing adjustment */
unsigned char wr_data_delay;
/* Minimum CKE pulse width (tCKE) */
unsigned char cke_pls;
/* Window for four activates (tFAW) */
unsigned short four_act;
/* FIXME add check that this must be less than acttorw_mclk */
add_lat_mclk = additive_latency;
cpo = popts->cpo_override;
#if defined(CONFIG_FSL_DDR1)
/*
* This is a lie. It should really be 1, but if it is
* set to 1, bits overlap into the old controller's
* otherwise unused ACSM field. If we leave it 0, then
* the HW will magically treat it as 1 for DDR 1. Oh Yea.
*/
wr_lat = 0;
#elif defined(CONFIG_FSL_DDR2)
wr_lat = cas_latency - 1;
#else
wr_lat = compute_cas_write_latency();
#endif
rd_to_pre = picos_to_mclk(common_dimm->tRTP_ps);
/*
* JEDEC has some min requirements for tRTP
*/
#if defined(CONFIG_FSL_DDR2)
if (rd_to_pre < 2)
rd_to_pre = 2;
#elif defined(CONFIG_FSL_DDR3)
if (rd_to_pre < 4)
rd_to_pre = 4;
#endif
if (additive_latency)
rd_to_pre += additive_latency;
if (popts->OTF_burst_chop_en)
rd_to_pre += 2; /* according to UM */
wr_data_delay = popts->write_data_delay;
cke_pls = picos_to_mclk(popts->tCKE_clock_pulse_width_ps);
four_act = picos_to_mclk(popts->tFAW_window_four_activates_ps);
ddr->timing_cfg_2 = (0
| ((add_lat_mclk & 0xf) << 28)
| ((cpo & 0x1f) << 23)
| ((wr_lat & 0xf) << 19)
| ((rd_to_pre & RD_TO_PRE_MASK) << RD_TO_PRE_SHIFT)
| ((wr_data_delay & WR_DATA_DELAY_MASK) << WR_DATA_DELAY_SHIFT)
| ((cke_pls & 0x7) << 6)
| ((four_act & 0x3f) << 0)
);
debug("FSLDDR: timing_cfg_2 = 0x%08x\n", ddr->timing_cfg_2);
}
/* DDR SDRAM Register Control Word */
static void set_ddr_sdram_rcw(fsl_ddr_cfg_regs_t *ddr,
const memctl_options_t *popts,
const common_timing_params_t *common_dimm)
{
if (common_dimm->all_DIMMs_registered
&& !common_dimm->all_DIMMs_unbuffered) {
if (popts->rcw_override) {
ddr->ddr_sdram_rcw_1 = popts->rcw_1;
ddr->ddr_sdram_rcw_2 = popts->rcw_2;
} else {
ddr->ddr_sdram_rcw_1 =
common_dimm->rcw[0] << 28 | \
common_dimm->rcw[1] << 24 | \
common_dimm->rcw[2] << 20 | \
common_dimm->rcw[3] << 16 | \
common_dimm->rcw[4] << 12 | \
common_dimm->rcw[5] << 8 | \
common_dimm->rcw[6] << 4 | \
common_dimm->rcw[7];
ddr->ddr_sdram_rcw_2 =
common_dimm->rcw[8] << 28 | \
common_dimm->rcw[9] << 24 | \
common_dimm->rcw[10] << 20 | \
common_dimm->rcw[11] << 16 | \
common_dimm->rcw[12] << 12 | \
common_dimm->rcw[13] << 8 | \
common_dimm->rcw[14] << 4 | \
common_dimm->rcw[15];
}
debug("FSLDDR: ddr_sdram_rcw_1 = 0x%08x\n", ddr->ddr_sdram_rcw_1);
debug("FSLDDR: ddr_sdram_rcw_2 = 0x%08x\n", ddr->ddr_sdram_rcw_2);
}
}
/* DDR SDRAM control configuration (DDR_SDRAM_CFG) */
static void set_ddr_sdram_cfg(fsl_ddr_cfg_regs_t *ddr,
const memctl_options_t *popts,
const common_timing_params_t *common_dimm)
{
unsigned int mem_en; /* DDR SDRAM interface logic enable */
unsigned int sren; /* Self refresh enable (during sleep) */
unsigned int ecc_en; /* ECC enable. */
unsigned int rd_en; /* Registered DIMM enable */
unsigned int sdram_type; /* Type of SDRAM */
unsigned int dyn_pwr; /* Dynamic power management mode */
unsigned int dbw; /* DRAM dta bus width */
unsigned int eight_be = 0; /* 8-beat burst enable, DDR2 is zero */
unsigned int ncap = 0; /* Non-concurrent auto-precharge */
unsigned int threeT_en; /* Enable 3T timing */
unsigned int twoT_en; /* Enable 2T timing */
unsigned int ba_intlv_ctl; /* Bank (CS) interleaving control */
unsigned int x32_en = 0; /* x32 enable */
unsigned int pchb8 = 0; /* precharge bit 8 enable */
unsigned int hse; /* Global half strength override */
unsigned int mem_halt = 0; /* memory controller halt */
unsigned int bi = 0; /* Bypass initialization */
mem_en = 1;
sren = popts->self_refresh_in_sleep;
if (common_dimm->all_DIMMs_ECC_capable) {
/* Allow setting of ECC only if all DIMMs are ECC. */
ecc_en = popts->ECC_mode;
} else {
ecc_en = 0;
}
if (common_dimm->all_DIMMs_registered
&& !common_dimm->all_DIMMs_unbuffered) {
rd_en = 1;
twoT_en = 0;
} else {
rd_en = 0;
twoT_en = popts->twoT_en;
}
sdram_type = CONFIG_FSL_SDRAM_TYPE;
dyn_pwr = popts->dynamic_power;
dbw = popts->data_bus_width;
/* 8-beat burst enable DDR-III case
* we must clear it when use the on-the-fly mode,
* must set it when use the 32-bits bus mode.
*/
if (sdram_type == SDRAM_TYPE_DDR3) {
if (popts->burst_length == DDR_BL8)
eight_be = 1;
if (popts->burst_length == DDR_OTF)
eight_be = 0;
if (dbw == 0x1)
eight_be = 1;
}
threeT_en = popts->threeT_en;
ba_intlv_ctl = popts->ba_intlv_ctl;
hse = popts->half_strength_driver_enable;
ddr->ddr_sdram_cfg = (0
| ((mem_en & 0x1) << 31)
| ((sren & 0x1) << 30)
| ((ecc_en & 0x1) << 29)
| ((rd_en & 0x1) << 28)
| ((sdram_type & 0x7) << 24)
| ((dyn_pwr & 0x1) << 21)
| ((dbw & 0x3) << 19)
| ((eight_be & 0x1) << 18)
| ((ncap & 0x1) << 17)
| ((threeT_en & 0x1) << 16)
| ((twoT_en & 0x1) << 15)
| ((ba_intlv_ctl & 0x7F) << 8)
| ((x32_en & 0x1) << 5)
| ((pchb8 & 0x1) << 4)
| ((hse & 0x1) << 3)
| ((mem_halt & 0x1) << 1)
| ((bi & 0x1) << 0)
);
debug("FSLDDR: ddr_sdram_cfg = 0x%08x\n", ddr->ddr_sdram_cfg);
}
/* DDR SDRAM control configuration 2 (DDR_SDRAM_CFG_2) */
static void set_ddr_sdram_cfg_2(fsl_ddr_cfg_regs_t *ddr,
const memctl_options_t *popts,
const unsigned int unq_mrs_en)
{
unsigned int frc_sr = 0; /* Force self refresh */
unsigned int sr_ie = 0; /* Self-refresh interrupt enable */
unsigned int dll_rst_dis; /* DLL reset disable */
unsigned int dqs_cfg; /* DQS configuration */
unsigned int odt_cfg = 0; /* ODT configuration */
unsigned int num_pr; /* Number of posted refreshes */
unsigned int obc_cfg; /* On-The-Fly Burst Chop Cfg */
unsigned int ap_en; /* Address Parity Enable */
unsigned int d_init; /* DRAM data initialization */
unsigned int rcw_en = 0; /* Register Control Word Enable */
unsigned int md_en = 0; /* Mirrored DIMM Enable */
unsigned int qd_en = 0; /* quad-rank DIMM Enable */
int i;
dll_rst_dis = 1; /* Make this configurable */
dqs_cfg = popts->DQS_config;
for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) {
if (popts->cs_local_opts[i].odt_rd_cfg
|| popts->cs_local_opts[i].odt_wr_cfg) {
odt_cfg = SDRAM_CFG2_ODT_ONLY_READ;
break;
}
}
num_pr = 1; /* Make this configurable */
/*
* 8572 manual says
* {TIMING_CFG_1[PRETOACT]
* + [DDR_SDRAM_CFG_2[NUM_PR]
* * ({EXT_REFREC || REFREC} + 8 + 2)]}
* << DDR_SDRAM_INTERVAL[REFINT]
*/
#if defined(CONFIG_FSL_DDR3)
obc_cfg = popts->OTF_burst_chop_en;
#else
obc_cfg = 0;
#endif
if (popts->registered_dimm_en) {
rcw_en = 1;
ap_en = popts->ap_en;
} else {
ap_en = 0;
}
#if defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
/* Use the DDR controller to auto initialize memory. */
d_init = popts->ECC_init_using_memctl;
ddr->ddr_data_init = CONFIG_MEM_INIT_VALUE;
debug("DDR: ddr_data_init = 0x%08x\n", ddr->ddr_data_init);
#else
/* Memory will be initialized via DMA, or not at all. */
d_init = 0;
#endif
#if defined(CONFIG_FSL_DDR3)
md_en = popts->mirrored_dimm;
#endif
qd_en = popts->quad_rank_present ? 1 : 0;
ddr->ddr_sdram_cfg_2 = (0
| ((frc_sr & 0x1) << 31)
| ((sr_ie & 0x1) << 30)
| ((dll_rst_dis & 0x1) << 29)
| ((dqs_cfg & 0x3) << 26)
| ((odt_cfg & 0x3) << 21)
| ((num_pr & 0xf) << 12)
| (qd_en << 9)
| (unq_mrs_en << 8)
| ((obc_cfg & 0x1) << 6)
| ((ap_en & 0x1) << 5)
| ((d_init & 0x1) << 4)
| ((rcw_en & 0x1) << 2)
| ((md_en & 0x1) << 0)
);
debug("FSLDDR: ddr_sdram_cfg_2 = 0x%08x\n", ddr->ddr_sdram_cfg_2);
}
/* DDR SDRAM Mode configuration 2 (DDR_SDRAM_MODE_2) */
static void set_ddr_sdram_mode_2(fsl_ddr_cfg_regs_t *ddr,
const memctl_options_t *popts,
const unsigned int unq_mrs_en)
{
unsigned short esdmode2 = 0; /* Extended SDRAM mode 2 */
unsigned short esdmode3 = 0; /* Extended SDRAM mode 3 */
#if defined(CONFIG_FSL_DDR3)
int i;
unsigned int rtt_wr = 0; /* Rtt_WR - dynamic ODT off */
unsigned int srt = 0; /* self-refresh temerature, normal range */
unsigned int asr = 0; /* auto self-refresh disable */
unsigned int cwl = compute_cas_write_latency() - 5;
unsigned int pasr = 0; /* partial array self refresh disable */
if (popts->rtt_override)
rtt_wr = popts->rtt_wr_override_value;
else
rtt_wr = popts->cs_local_opts[0].odt_rtt_wr;
esdmode2 = (0
| ((rtt_wr & 0x3) << 9)
| ((srt & 0x1) << 7)
| ((asr & 0x1) << 6)
| ((cwl & 0x7) << 3)
| ((pasr & 0x7) << 0));
#endif
ddr->ddr_sdram_mode_2 = (0
| ((esdmode2 & 0xFFFF) << 16)
| ((esdmode3 & 0xFFFF) << 0)
);
debug("FSLDDR: ddr_sdram_mode_2 = 0x%08x\n", ddr->ddr_sdram_mode_2);
#ifdef CONFIG_FSL_DDR3
if (unq_mrs_en) { /* unique mode registers are supported */
for (i = 1; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) {
if (popts->rtt_override)
rtt_wr = popts->rtt_wr_override_value;
else
rtt_wr = popts->cs_local_opts[i].odt_rtt_wr;
esdmode2 &= 0xF9FF; /* clear bit 10, 9 */
esdmode2 |= (rtt_wr & 0x3) << 9;
switch (i) {
case 1:
ddr->ddr_sdram_mode_4 = (0
| ((esdmode2 & 0xFFFF) << 16)
| ((esdmode3 & 0xFFFF) << 0)
);
break;
case 2:
ddr->ddr_sdram_mode_6 = (0
| ((esdmode2 & 0xFFFF) << 16)
| ((esdmode3 & 0xFFFF) << 0)
);
break;
case 3:
ddr->ddr_sdram_mode_8 = (0
| ((esdmode2 & 0xFFFF) << 16)
| ((esdmode3 & 0xFFFF) << 0)
);
break;
}
}
debug("FSLDDR: ddr_sdram_mode_4 = 0x%08x\n",
ddr->ddr_sdram_mode_4);
debug("FSLDDR: ddr_sdram_mode_6 = 0x%08x\n",
ddr->ddr_sdram_mode_6);
debug("FSLDDR: ddr_sdram_mode_8 = 0x%08x\n",
ddr->ddr_sdram_mode_8);
}
#endif
}
/* DDR SDRAM Interval Configuration (DDR_SDRAM_INTERVAL) */
static void set_ddr_sdram_interval(fsl_ddr_cfg_regs_t *ddr,
const memctl_options_t *popts,
const common_timing_params_t *common_dimm)
{
unsigned int refint; /* Refresh interval */
unsigned int bstopre; /* Precharge interval */
refint = picos_to_mclk(common_dimm->refresh_rate_ps);
bstopre = popts->bstopre;
/* refint field used 0x3FFF in earlier controllers */
ddr->ddr_sdram_interval = (0
| ((refint & 0xFFFF) << 16)
| ((bstopre & 0x3FFF) << 0)
);
debug("FSLDDR: ddr_sdram_interval = 0x%08x\n", ddr->ddr_sdram_interval);
}
#if defined(CONFIG_FSL_DDR3)
/* DDR SDRAM Mode configuration set (DDR_SDRAM_MODE) */
static void set_ddr_sdram_mode(fsl_ddr_cfg_regs_t *ddr,
const memctl_options_t *popts,
const common_timing_params_t *common_dimm,
unsigned int cas_latency,
unsigned int additive_latency,
const unsigned int unq_mrs_en)
{
unsigned short esdmode; /* Extended SDRAM mode */
unsigned short sdmode; /* SDRAM mode */
/* Mode Register - MR1 */
unsigned int qoff = 0; /* Output buffer enable 0=yes, 1=no */
unsigned int tdqs_en = 0; /* TDQS Enable: 0=no, 1=yes */
unsigned int rtt;
unsigned int wrlvl_en = 0; /* Write level enable: 0=no, 1=yes */
unsigned int al = 0; /* Posted CAS# additive latency (AL) */
unsigned int dic = 0; /* Output driver impedance, 40ohm */
unsigned int dll_en = 0; /* DLL Enable 0=Enable (Normal),
1=Disable (Test/Debug) */
/* Mode Register - MR0 */
unsigned int dll_on; /* DLL control for precharge PD, 0=off, 1=on */
unsigned int wr = 0; /* Write Recovery */
unsigned int dll_rst; /* DLL Reset */
unsigned int mode; /* Normal=0 or Test=1 */
unsigned int caslat = 4;/* CAS# latency, default set as 6 cycles */
/* BT: Burst Type (0=Nibble Sequential, 1=Interleaved) */
unsigned int bt;
unsigned int bl; /* BL: Burst Length */
unsigned int wr_mclk;
/*
* DDR_SDRAM_MODE doesn't support 9,11,13,15
* Please refer JEDEC Standard No. 79-3E for Mode Register MR0
* for this table
*/
static const u8 wr_table[] = {1, 2, 3, 4, 5, 5, 6, 6, 7, 7, 0, 0};
const unsigned int mclk_ps = get_memory_clk_period_ps();
int i;
if (popts->rtt_override)
rtt = popts->rtt_override_value;
else
rtt = popts->cs_local_opts[0].odt_rtt_norm;
if (additive_latency == (cas_latency - 1))
al = 1;
if (additive_latency == (cas_latency - 2))
al = 2;
if (popts->quad_rank_present)
dic = 1; /* output driver impedance 240/7 ohm */
/*
* The esdmode value will also be used for writing
* MR1 during write leveling for DDR3, although the
* bits specifically related to the write leveling
* scheme will be handled automatically by the DDR
* controller. so we set the wrlvl_en = 0 here.
*/
esdmode = (0
| ((qoff & 0x1) << 12)
| ((tdqs_en & 0x1) << 11)
| ((rtt & 0x4) << 7) /* rtt field is split */
| ((wrlvl_en & 0x1) << 7)
| ((rtt & 0x2) << 5) /* rtt field is split */
| ((dic & 0x2) << 4) /* DIC field is split */
| ((al & 0x3) << 3)
| ((rtt & 0x1) << 2) /* rtt field is split */
| ((dic & 0x1) << 1) /* DIC field is split */
| ((dll_en & 0x1) << 0)
);
/*
* DLL control for precharge PD
* 0=slow exit DLL off (tXPDLL)
* 1=fast exit DLL on (tXP)
*/
dll_on = 1;
wr_mclk = (common_dimm->tWR_ps + mclk_ps - 1) / mclk_ps;
if (wr_mclk <= 16) {
wr = wr_table[wr_mclk - 5];
} else {
printf("Error: unsupported write recovery for mode register "
"wr_mclk = %d\n", wr_mclk);
}
dll_rst = 0; /* dll no reset */
mode = 0; /* normal mode */
/* look up table to get the cas latency bits */
if (cas_latency >= 5 && cas_latency <= 16) {
unsigned char cas_latency_table[] = {
0x2, /* 5 clocks */
0x4, /* 6 clocks */
0x6, /* 7 clocks */
0x8, /* 8 clocks */
0xa, /* 9 clocks */
0xc, /* 10 clocks */
0xe, /* 11 clocks */
0x1, /* 12 clocks */
0x3, /* 13 clocks */
0x5, /* 14 clocks */
0x7, /* 15 clocks */
0x9, /* 16 clocks */
};
caslat = cas_latency_table[cas_latency - 5];
} else {
printf("Error: unsupported cas latency for mode register\n");
}
bt = 0; /* Nibble sequential */
switch (popts->burst_length) {
case DDR_BL8:
bl = 0;
break;
case DDR_OTF:
bl = 1;
break;
case DDR_BC4:
bl = 2;
break;
default:
printf("Error: invalid burst length of %u specified. "
" Defaulting to on-the-fly BC4 or BL8 beats.\n",
popts->burst_length);
bl = 1;
break;
}
sdmode = (0
| ((dll_on & 0x1) << 12)
| ((wr & 0x7) << 9)
| ((dll_rst & 0x1) << 8)
| ((mode & 0x1) << 7)
| (((caslat >> 1) & 0x7) << 4)
| ((bt & 0x1) << 3)
| ((caslat & 1) << 2)
| ((bl & 0x3) << 0)
);
ddr->ddr_sdram_mode = (0
| ((esdmode & 0xFFFF) << 16)
| ((sdmode & 0xFFFF) << 0)
);
debug("FSLDDR: ddr_sdram_mode = 0x%08x\n", ddr->ddr_sdram_mode);
if (unq_mrs_en) { /* unique mode registers are supported */
for (i = 1; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) {
if (popts->rtt_override)
rtt = popts->rtt_override_value;
else
rtt = popts->cs_local_opts[i].odt_rtt_norm;
esdmode &= 0xFDBB; /* clear bit 9,6,2 */
esdmode |= (0
| ((rtt & 0x4) << 7) /* rtt field is split */
| ((rtt & 0x2) << 5) /* rtt field is split */
| ((rtt & 0x1) << 2) /* rtt field is split */
);
switch (i) {
case 1:
ddr->ddr_sdram_mode_3 = (0
| ((esdmode & 0xFFFF) << 16)
| ((sdmode & 0xFFFF) << 0)
);
break;
case 2:
ddr->ddr_sdram_mode_5 = (0
| ((esdmode & 0xFFFF) << 16)
| ((sdmode & 0xFFFF) << 0)
);
break;
case 3:
ddr->ddr_sdram_mode_7 = (0
| ((esdmode & 0xFFFF) << 16)
| ((sdmode & 0xFFFF) << 0)
);
break;
}
}
debug("FSLDDR: ddr_sdram_mode_3 = 0x%08x\n",
ddr->ddr_sdram_mode_3);
debug("FSLDDR: ddr_sdram_mode_5 = 0x%08x\n",
ddr->ddr_sdram_mode_5);
debug("FSLDDR: ddr_sdram_mode_5 = 0x%08x\n",
ddr->ddr_sdram_mode_5);
}
}
#else /* !CONFIG_FSL_DDR3 */
/* DDR SDRAM Mode configuration set (DDR_SDRAM_MODE) */
static void set_ddr_sdram_mode(fsl_ddr_cfg_regs_t *ddr,
const memctl_options_t *popts,
const common_timing_params_t *common_dimm,
unsigned int cas_latency,
unsigned int additive_latency,
const unsigned int unq_mrs_en)
{
unsigned short esdmode; /* Extended SDRAM mode */
unsigned short sdmode; /* SDRAM mode */
/*
* FIXME: This ought to be pre-calculated in a
* technology-specific routine,
* e.g. compute_DDR2_mode_register(), and then the
* sdmode and esdmode passed in as part of common_dimm.
*/
/* Extended Mode Register */
unsigned int mrs = 0; /* Mode Register Set */
unsigned int outputs = 0; /* 0=Enabled, 1=Disabled */
unsigned int rdqs_en = 0; /* RDQS Enable: 0=no, 1=yes */
unsigned int dqs_en = 0; /* DQS# Enable: 0=enable, 1=disable */
unsigned int ocd = 0; /* 0x0=OCD not supported,
0x7=OCD default state */
unsigned int rtt;
unsigned int al; /* Posted CAS# additive latency (AL) */
unsigned int ods = 0; /* Output Drive Strength:
0 = Full strength (18ohm)
1 = Reduced strength (4ohm) */
unsigned int dll_en = 0; /* DLL Enable 0=Enable (Normal),
1=Disable (Test/Debug) */
/* Mode Register (MR) */
unsigned int mr; /* Mode Register Definition */
unsigned int pd; /* Power-Down Mode */
unsigned int wr; /* Write Recovery */
unsigned int dll_res; /* DLL Reset */
unsigned int mode; /* Normal=0 or Test=1 */
unsigned int caslat = 0;/* CAS# latency */
/* BT: Burst Type (0=Sequential, 1=Interleaved) */
unsigned int bt;
unsigned int bl; /* BL: Burst Length */
#if defined(CONFIG_FSL_DDR2)
const unsigned int mclk_ps = get_memory_clk_period_ps();
#endif
dqs_en = !popts->DQS_config;
rtt = fsl_ddr_get_rtt();
al = additive_latency;
esdmode = (0
| ((mrs & 0x3) << 14)
| ((outputs & 0x1) << 12)
| ((rdqs_en & 0x1) << 11)
| ((dqs_en & 0x1) << 10)
| ((ocd & 0x7) << 7)
| ((rtt & 0x2) << 5) /* rtt field is split */
| ((al & 0x7) << 3)
| ((rtt & 0x1) << 2) /* rtt field is split */
| ((ods & 0x1) << 1)
| ((dll_en & 0x1) << 0)
);
mr = 0; /* FIXME: CHECKME */
/*
* 0 = Fast Exit (Normal)
* 1 = Slow Exit (Low Power)
*/
pd = 0;
#if defined(CONFIG_FSL_DDR1)
wr = 0; /* Historical */
#elif defined(CONFIG_FSL_DDR2)
wr = (common_dimm->tWR_ps + mclk_ps - 1) / mclk_ps - 1;
#endif
dll_res = 0;
mode = 0;
#if defined(CONFIG_FSL_DDR1)
if (1 <= cas_latency && cas_latency <= 4) {
unsigned char mode_caslat_table[4] = {
0x5, /* 1.5 clocks */
0x2, /* 2.0 clocks */
0x6, /* 2.5 clocks */
0x3 /* 3.0 clocks */
};
caslat = mode_caslat_table[cas_latency - 1];
} else {
printf("Warning: unknown cas_latency %d\n", cas_latency);
}
#elif defined(CONFIG_FSL_DDR2)
caslat = cas_latency;
#endif
bt = 0;
switch (popts->burst_length) {
case DDR_BL4:
bl = 2;
break;
case DDR_BL8:
bl = 3;
break;
default:
printf("Error: invalid burst length of %u specified. "
" Defaulting to 4 beats.\n",
popts->burst_length);
bl = 2;
break;
}
sdmode = (0
| ((mr & 0x3) << 14)
| ((pd & 0x1) << 12)
| ((wr & 0x7) << 9)
| ((dll_res & 0x1) << 8)
| ((mode & 0x1) << 7)
| ((caslat & 0x7) << 4)
| ((bt & 0x1) << 3)
| ((bl & 0x7) << 0)
);
ddr->ddr_sdram_mode = (0
| ((esdmode & 0xFFFF) << 16)
| ((sdmode & 0xFFFF) << 0)
);
debug("FSLDDR: ddr_sdram_mode = 0x%08x\n", ddr->ddr_sdram_mode);
}
#endif
/* DDR SDRAM Data Initialization (DDR_DATA_INIT) */
static void set_ddr_data_init(fsl_ddr_cfg_regs_t *ddr)
{
unsigned int init_value; /* Initialization value */
init_value = 0xDEADBEEF;
ddr->ddr_data_init = init_value;
}
/*
* DDR SDRAM Clock Control (DDR_SDRAM_CLK_CNTL)
* The old controller on the 8540/60 doesn't have this register.
* Hope it's OK to set it (to 0) anyway.
*/
static void set_ddr_sdram_clk_cntl(fsl_ddr_cfg_regs_t *ddr,
const memctl_options_t *popts)
{
unsigned int clk_adjust; /* Clock adjust */
clk_adjust = popts->clk_adjust;
ddr->ddr_sdram_clk_cntl = (clk_adjust & 0xF) << 23;
debug("FSLDDR: clk_cntl = 0x%08x\n", ddr->ddr_sdram_clk_cntl);
}
/* DDR Initialization Address (DDR_INIT_ADDR) */
static void set_ddr_init_addr(fsl_ddr_cfg_regs_t *ddr)
{
unsigned int init_addr = 0; /* Initialization address */
ddr->ddr_init_addr = init_addr;
}
/* DDR Initialization Address (DDR_INIT_EXT_ADDR) */
static void set_ddr_init_ext_addr(fsl_ddr_cfg_regs_t *ddr)
{
unsigned int uia = 0; /* Use initialization address */
unsigned int init_ext_addr = 0; /* Initialization address */
ddr->ddr_init_ext_addr = (0
| ((uia & 0x1) << 31)
| (init_ext_addr & 0xF)
);
}
/* DDR SDRAM Timing Configuration 4 (TIMING_CFG_4) */
static void set_timing_cfg_4(fsl_ddr_cfg_regs_t *ddr,
const memctl_options_t *popts)
{
unsigned int rwt = 0; /* Read-to-write turnaround for same CS */
unsigned int wrt = 0; /* Write-to-read turnaround for same CS */
unsigned int rrt = 0; /* Read-to-read turnaround for same CS */
unsigned int wwt = 0; /* Write-to-write turnaround for same CS */
unsigned int dll_lock = 0; /* DDR SDRAM DLL Lock Time */
#if defined(CONFIG_FSL_DDR3)
if (popts->burst_length == DDR_BL8) {
/* We set BL/2 for fixed BL8 */
rrt = 0; /* BL/2 clocks */
wwt = 0; /* BL/2 clocks */
} else {
/* We need to set BL/2 + 2 to BC4 and OTF */
rrt = 2; /* BL/2 + 2 clocks */
wwt = 2; /* BL/2 + 2 clocks */
}
dll_lock = 1; /* tDLLK = 512 clocks from spec */
#endif
ddr->timing_cfg_4 = (0
| ((rwt & 0xf) << 28)
| ((wrt & 0xf) << 24)
| ((rrt & 0xf) << 20)
| ((wwt & 0xf) << 16)
| (dll_lock & 0x3)
);
debug("FSLDDR: timing_cfg_4 = 0x%08x\n", ddr->timing_cfg_4);
}
/* DDR SDRAM Timing Configuration 5 (TIMING_CFG_5) */
static void set_timing_cfg_5(fsl_ddr_cfg_regs_t *ddr, unsigned int cas_latency)
{
unsigned int rodt_on = 0; /* Read to ODT on */
unsigned int rodt_off = 0; /* Read to ODT off */
unsigned int wodt_on = 0; /* Write to ODT on */
unsigned int wodt_off = 0; /* Write to ODT off */
#if defined(CONFIG_FSL_DDR3)
/* rodt_on = timing_cfg_1[caslat] - timing_cfg_2[wrlat] + 1 */
rodt_on = cas_latency - ((ddr->timing_cfg_2 & 0x00780000) >> 19) + 1;
rodt_off = 4; /* 4 clocks */
wodt_on = 1; /* 1 clocks */
wodt_off = 4; /* 4 clocks */
#endif
ddr->timing_cfg_5 = (0
| ((rodt_on & 0x1f) << 24)
| ((rodt_off & 0x7) << 20)
| ((wodt_on & 0x1f) << 12)
| ((wodt_off & 0x7) << 8)
);
debug("FSLDDR: timing_cfg_5 = 0x%08x\n", ddr->timing_cfg_5);
}
/* DDR ZQ Calibration Control (DDR_ZQ_CNTL) */
static void set_ddr_zq_cntl(fsl_ddr_cfg_regs_t *ddr, unsigned int zq_en)
{
unsigned int zqinit = 0;/* POR ZQ Calibration Time (tZQinit) */
/* Normal Operation Full Calibration Time (tZQoper) */
unsigned int zqoper = 0;
/* Normal Operation Short Calibration Time (tZQCS) */
unsigned int zqcs = 0;
if (zq_en) {
zqinit = 9; /* 512 clocks */
zqoper = 8; /* 256 clocks */
zqcs = 6; /* 64 clocks */
}
ddr->ddr_zq_cntl = (0
| ((zq_en & 0x1) << 31)
| ((zqinit & 0xF) << 24)
| ((zqoper & 0xF) << 16)
| ((zqcs & 0xF) << 8)
);
debug("FSLDDR: zq_cntl = 0x%08x\n", ddr->ddr_zq_cntl);
}
/* DDR Write Leveling Control (DDR_WRLVL_CNTL) */
static void set_ddr_wrlvl_cntl(fsl_ddr_cfg_regs_t *ddr, unsigned int wrlvl_en,
const memctl_options_t *popts)
{
/*
* First DQS pulse rising edge after margining mode
* is programmed (tWL_MRD)
*/
unsigned int wrlvl_mrd = 0;
/* ODT delay after margining mode is programmed (tWL_ODTEN) */
unsigned int wrlvl_odten = 0;
/* DQS/DQS_ delay after margining mode is programmed (tWL_DQSEN) */
unsigned int wrlvl_dqsen = 0;
/* WRLVL_SMPL: Write leveling sample time */
unsigned int wrlvl_smpl = 0;
/* WRLVL_WLR: Write leveling repeition time */
unsigned int wrlvl_wlr = 0;
/* WRLVL_START: Write leveling start time */
unsigned int wrlvl_start = 0;
/* suggest enable write leveling for DDR3 due to fly-by topology */
if (wrlvl_en) {
/* tWL_MRD min = 40 nCK, we set it 64 */
wrlvl_mrd = 0x6;
/* tWL_ODTEN 128 */
wrlvl_odten = 0x7;
/* tWL_DQSEN min = 25 nCK, we set it 32 */
wrlvl_dqsen = 0x5;
/*
* Write leveling sample time at least need 6 clocks
* higher than tWLO to allow enough time for progagation
* delay and sampling the prime data bits.
*/
wrlvl_smpl = 0xf;
/*
* Write leveling repetition time
* at least tWLO + 6 clocks clocks
* we set it 64
*/
wrlvl_wlr = 0x6;
/*
* Write leveling start time
* The value use for the DQS_ADJUST for the first sample
* when write leveling is enabled. It probably needs to be
* overriden per platform.
*/
wrlvl_start = 0x8;
/*
* Override the write leveling sample and start time
* according to specific board
*/
if (popts->wrlvl_override) {
wrlvl_smpl = popts->wrlvl_sample;
wrlvl_start = popts->wrlvl_start;
}
}
ddr->ddr_wrlvl_cntl = (0
| ((wrlvl_en & 0x1) << 31)
| ((wrlvl_mrd & 0x7) << 24)
| ((wrlvl_odten & 0x7) << 20)
| ((wrlvl_dqsen & 0x7) << 16)
| ((wrlvl_smpl & 0xf) << 12)
| ((wrlvl_wlr & 0x7) << 8)
| ((wrlvl_start & 0x1F) << 0)
);
debug("FSLDDR: wrlvl_cntl = 0x%08x\n", ddr->ddr_wrlvl_cntl);
}
/* DDR Self Refresh Counter (DDR_SR_CNTR) */
static void set_ddr_sr_cntr(fsl_ddr_cfg_regs_t *ddr, unsigned int sr_it)
{
/* Self Refresh Idle Threshold */
ddr->ddr_sr_cntr = (sr_it & 0xF) << 16;
}
static void set_ddr_eor(fsl_ddr_cfg_regs_t *ddr, const memctl_options_t *popts)
{
if (popts->addr_hash) {
ddr->ddr_eor = 0x40000000; /* address hash enable */
puts("Address hashing enabled.\n");
}
}
static void set_ddr_cdr1(fsl_ddr_cfg_regs_t *ddr, const memctl_options_t *popts)
{
ddr->ddr_cdr1 = popts->ddr_cdr1;
debug("FSLDDR: ddr_cdr1 = 0x%08x\n", ddr->ddr_cdr1);
}
unsigned int
check_fsl_memctl_config_regs(const fsl_ddr_cfg_regs_t *ddr)
{
unsigned int res = 0;
/*
* Check that DDR_SDRAM_CFG[RD_EN] and DDR_SDRAM_CFG[2T_EN] are
* not set at the same time.
*/
if (ddr->ddr_sdram_cfg & 0x10000000
&& ddr->ddr_sdram_cfg & 0x00008000) {
printf("Error: DDR_SDRAM_CFG[RD_EN] and DDR_SDRAM_CFG[2T_EN] "
" should not be set at the same time.\n");
res++;
}
return res;
}
unsigned int
compute_fsl_memctl_config_regs(const memctl_options_t *popts,
fsl_ddr_cfg_regs_t *ddr,
const common_timing_params_t *common_dimm,
const dimm_params_t *dimm_params,
unsigned int dbw_cap_adj,
unsigned int size_only)
{
unsigned int i;
unsigned int cas_latency;
unsigned int additive_latency;
unsigned int sr_it;
unsigned int zq_en;
unsigned int wrlvl_en;
unsigned int ip_rev = 0;
unsigned int unq_mrs_en = 0;
int cs_en = 1;
memset(ddr, 0, sizeof(fsl_ddr_cfg_regs_t));
if (common_dimm == NULL) {
printf("Error: subset DIMM params struct null pointer\n");
return 1;
}
/*
* Process overrides first.
*
* FIXME: somehow add dereated caslat to this
*/
cas_latency = (popts->cas_latency_override)
? popts->cas_latency_override_value
: common_dimm->lowest_common_SPD_caslat;
additive_latency = (popts->additive_latency_override)
? popts->additive_latency_override_value
: common_dimm->additive_latency;
sr_it = (popts->auto_self_refresh_en)
? popts->sr_it
: 0;
/* ZQ calibration */
zq_en = (popts->zq_en) ? 1 : 0;
/* write leveling */
wrlvl_en = (popts->wrlvl_en) ? 1 : 0;
/* Chip Select Memory Bounds (CSn_BNDS) */
for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) {
unsigned long long ea, sa;
unsigned int cs_per_dimm
= CONFIG_CHIP_SELECTS_PER_CTRL / CONFIG_DIMM_SLOTS_PER_CTLR;
unsigned int dimm_number
= i / cs_per_dimm;
unsigned long long rank_density
= dimm_params[dimm_number].rank_density >> dbw_cap_adj;
if (dimm_params[dimm_number].n_ranks == 0) {
debug("Skipping setup of CS%u "
"because n_ranks on DIMM %u is 0\n", i, dimm_number);
continue;
}
if (popts->memctl_interleaving) {
switch (popts->ba_intlv_ctl & FSL_DDR_CS0_CS1_CS2_CS3) {
case FSL_DDR_CS0_CS1_CS2_CS3:
break;
case FSL_DDR_CS0_CS1:
case FSL_DDR_CS0_CS1_AND_CS2_CS3:
if (i > 1)
cs_en = 0;
break;
case FSL_DDR_CS2_CS3:
default:
if (i > 0)
cs_en = 0;
break;
}
sa = common_dimm->base_address;
ea = common_dimm->total_mem - 1;
} else if (!popts->memctl_interleaving) {
/*
* If memory interleaving between controllers is NOT
* enabled, the starting address for each memory
* controller is distinct. However, because rank
* interleaving is enabled, the starting and ending
* addresses of the total memory on that memory
* controller needs to be programmed into its
* respective CS0_BNDS.
*/
switch (popts->ba_intlv_ctl & FSL_DDR_CS0_CS1_CS2_CS3) {
case FSL_DDR_CS0_CS1_CS2_CS3:
sa = common_dimm->base_address;
ea = common_dimm->total_mem - 1;
break;
case FSL_DDR_CS0_CS1_AND_CS2_CS3:
if ((i >= 2) && (dimm_number == 0)) {
sa = dimm_params[dimm_number].base_address +
2 * rank_density;
ea = sa + 2 * rank_density - 1;
} else {
sa = dimm_params[dimm_number].base_address;
ea = sa + 2 * rank_density - 1;
}
break;
case FSL_DDR_CS0_CS1:
if (dimm_params[dimm_number].n_ranks > (i % cs_per_dimm)) {
sa = dimm_params[dimm_number].base_address;
ea = sa + rank_density - 1;
if (i != 1)
sa += (i % cs_per_dimm) * rank_density;
ea += (i % cs_per_dimm) * rank_density;
} else {
sa = 0;
ea = 0;
}
if (i == 0)
ea += rank_density;
break;
case FSL_DDR_CS2_CS3:
if (dimm_params[dimm_number].n_ranks > (i % cs_per_dimm)) {
sa = dimm_params[dimm_number].base_address;
ea = sa + rank_density - 1;
if (i != 3)
sa += (i % cs_per_dimm) * rank_density;
ea += (i % cs_per_dimm) * rank_density;
} else {
sa = 0;
ea = 0;
}
if (i == 2)
ea += (rank_density >> dbw_cap_adj);
break;
default: /* No bank(chip-select) interleaving */
sa = dimm_params[dimm_number].base_address;
ea = sa + rank_density - 1;
if (dimm_params[dimm_number].n_ranks > (i % cs_per_dimm)) {
sa += (i % cs_per_dimm) * rank_density;
ea += (i % cs_per_dimm) * rank_density;
} else {
sa = 0;
ea = 0;
}
break;
}
}
sa >>= 24;
ea >>= 24;
ddr->cs[i].bnds = (0
| ((sa & 0xFFF) << 16) /* starting address MSB */
| ((ea & 0xFFF) << 0) /* ending address MSB */
);
debug("FSLDDR: cs[%d]_bnds = 0x%08x\n", i, ddr->cs[i].bnds);
if (cs_en) {
set_csn_config(dimm_number, i, ddr, popts, dimm_params);
set_csn_config_2(i, ddr);
} else
debug("CS%d is disabled.\n", i);
}
/*
* In the case we only need to compute the ddr sdram size, we only need
* to set csn registers, so return from here.
*/
if (size_only)
return 0;
set_ddr_eor(ddr, popts);
#if !defined(CONFIG_FSL_DDR1)
set_timing_cfg_0(ddr, popts);
#endif
set_timing_cfg_3(ddr, common_dimm, cas_latency);
set_timing_cfg_1(ddr, popts, common_dimm, cas_latency);
set_timing_cfg_2(ddr, popts, common_dimm,
cas_latency, additive_latency);
set_ddr_cdr1(ddr, popts);
set_ddr_sdram_cfg(ddr, popts, common_dimm);
ip_rev = fsl_ddr_get_version();
if (ip_rev > 0x40400)
unq_mrs_en = 1;
set_ddr_sdram_cfg_2(ddr, popts, unq_mrs_en);
set_ddr_sdram_mode(ddr, popts, common_dimm,
cas_latency, additive_latency, unq_mrs_en);
set_ddr_sdram_mode_2(ddr, popts, unq_mrs_en);
set_ddr_sdram_interval(ddr, popts, common_dimm);
set_ddr_data_init(ddr);
set_ddr_sdram_clk_cntl(ddr, popts);
set_ddr_init_addr(ddr);
set_ddr_init_ext_addr(ddr);
set_timing_cfg_4(ddr, popts);
set_timing_cfg_5(ddr, cas_latency);
set_ddr_zq_cntl(ddr, zq_en);
set_ddr_wrlvl_cntl(ddr, wrlvl_en, popts);
set_ddr_sr_cntr(ddr, sr_it);
set_ddr_sdram_rcw(ddr, popts, common_dimm);
return check_fsl_memctl_config_regs(ddr);
}