include/configs/corenet_ds.h - filogic/uboot - Gitiles

 /* SPDX-License-Identifier: GPL-2.0+ */
 /*
  * Copyright 2009-2012 Freescale Semiconductor, Inc.
  * Copyright 2020 NXP
  */

 /*
  * Corenet DS style board configuration file
  */
 #ifndef __CONFIG_H
 #define __CONFIG_H

 #include <linux/stringify.h>

 #include "../board/freescale/common/ics307_clk.h"

 #ifdef CONFIG_RAMBOOT_PBL
 #ifdef CONFIG_NXP_ESBC
 #define CONFIG_RAMBOOT_TEXT_BASE	CONFIG_SYS_TEXT_BASE
 #define CONFIG_RESET_VECTOR_ADDRESS	0xfffffffc
 #ifdef CONFIG_MTD_RAW_NAND
 #define CONFIG_RAMBOOT_NAND
 #endif
 #define CONFIG_BOOTSCRIPT_COPY_RAM
 #else
 #define CONFIG_RAMBOOT_TEXT_BASE	CONFIG_SYS_TEXT_BASE
 #define CONFIG_RESET_VECTOR_ADDRESS	0xfffffffc
 #endif
 #endif

 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
 /* Set 1M boot space */
 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000)
 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \
 		(0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR)
 #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
 #endif

 /* High Level Configuration Options */
 #define CONFIG_SYS_BOOK3E_HV		/* Category E.HV supported */

 #ifndef CONFIG_RESET_VECTOR_ADDRESS
 #define CONFIG_RESET_VECTOR_ADDRESS	0xeffffffc
 #endif

 #define CONFIG_SYS_FSL_CPC		/* Corenet Platform Cache */
 #define CONFIG_SYS_NUM_CPC		CONFIG_SYS_NUM_DDR_CTLRS
 #define CONFIG_PCIE1			/* PCIE controller 1 */
 #define CONFIG_PCIE2			/* PCIE controller 2 */
 #define CONFIG_SYS_PCI_64BIT		/* enable 64-bit PCI resources */

 #if defined(CONFIG_SPIFLASH)
 #elif defined(CONFIG_SDCARD)
 #define CONFIG_FSL_FIXED_MMC_LOCATION
 #endif

 #define CONFIG_SYS_CLK_FREQ	get_board_sys_clk() /* sysclk for MPC85xx */

 /*
  * These can be toggled for performance analysis, otherwise use default.
  */
 #define CONFIG_SYS_CACHE_STASHING
 #define CONFIG_BACKSIDE_L2_CACHE
 #define CONFIG_SYS_INIT_L2CSR0		L2CSR0_L2E
 #define CONFIG_BTB			/* toggle branch predition */
 #ifdef CONFIG_DDR_ECC
 #define CONFIG_MEM_INIT_VALUE		0xdeadbeef
 #endif

 #define CONFIG_ENABLE_36BIT_PHYS

 #define CONFIG_POST CONFIG_SYS_POST_MEMORY	/* test POST memory test */

 /*
  *  Config the L3 Cache as L3 SRAM
  */
 #define CONFIG_SYS_INIT_L3_ADDR		CONFIG_RAMBOOT_TEXT_BASE
 #ifdef CONFIG_PHYS_64BIT
 #define CONFIG_SYS_INIT_L3_ADDR_PHYS	(0xf00000000ull | CONFIG_RAMBOOT_TEXT_BASE)
 #else
 #define CONFIG_SYS_INIT_L3_ADDR_PHYS	CONFIG_SYS_INIT_L3_ADDR
 #endif
 #define CONFIG_SYS_L3_SIZE		(1024 << 10)
 #define CONFIG_SYS_INIT_L3_END (CONFIG_SYS_INIT_L3_ADDR + CONFIG_SYS_L3_SIZE)

 #ifdef CONFIG_PHYS_64BIT
 #define CONFIG_SYS_DCSRBAR		0xf0000000
 #define CONFIG_SYS_DCSRBAR_PHYS		0xf00000000ull
 #endif

 /* EEPROM */
 #define CONFIG_SYS_I2C_EEPROM_NXID
 #define CONFIG_SYS_EEPROM_BUS_NUM	0

 /*
  * DDR Setup
  */
 #define CONFIG_VERY_BIG_RAM
 #define CONFIG_SYS_DDR_SDRAM_BASE	0x00000000
 #define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE

 #define CONFIG_DIMM_SLOTS_PER_CTLR	1
 #define CONFIG_CHIP_SELECTS_PER_CTRL	(4 * CONFIG_DIMM_SLOTS_PER_CTLR)

 #define CONFIG_SYS_SPD_BUS_NUM	1
 #define SPD_EEPROM_ADDRESS1	0x51
 #define SPD_EEPROM_ADDRESS2	0x52
 #define SPD_EEPROM_ADDRESS	SPD_EEPROM_ADDRESS1	/* for p3041/p5010 */
 #define CONFIG_SYS_SDRAM_SIZE	4096	/* for fixed parameter use */

 /*
  * Local Bus Definitions
  */

 /* Set the local bus clock 1/8 of platform clock */
 #define CONFIG_SYS_LBC_LCRR		LCRR_CLKDIV_8

 #define CONFIG_SYS_FLASH_BASE		0xe0000000	/* Start of PromJet */
 #ifdef CONFIG_PHYS_64BIT
 #define CONFIG_SYS_FLASH_BASE_PHYS	0xfe0000000ull
 #else
 #define CONFIG_SYS_FLASH_BASE_PHYS	CONFIG_SYS_FLASH_BASE
 #endif

 #define CONFIG_SYS_FLASH_BR_PRELIM \
 		(BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000) \
 		 | BR_PS_16 | BR_V)
 #define CONFIG_SYS_FLASH_OR_PRELIM ((0xf8000ff7 & ~OR_GPCM_SCY & ~OR_GPCM_EHTR) \
 					| OR_GPCM_SCY_8 | OR_GPCM_EHTR_CLEAR)

 #define CONFIG_SYS_BR1_PRELIM \
 	(BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | BR_PS_16 | BR_V)
 #define CONFIG_SYS_OR1_PRELIM	0xf8000ff7

 #define PIXIS_BASE		0xffdf0000	/* PIXIS registers */
 #ifdef CONFIG_PHYS_64BIT
 #define PIXIS_BASE_PHYS		0xfffdf0000ull
 #else
 #define PIXIS_BASE_PHYS		PIXIS_BASE
 #endif

 #define CONFIG_SYS_BR3_PRELIM	(BR_PHYS_ADDR(PIXIS_BASE_PHYS) | BR_PS_8 | BR_V)
 #define CONFIG_SYS_OR3_PRELIM	0xffffeff7	/* 32KB but only 4k mapped */

 #define PIXIS_LBMAP_SWITCH	7
 #define PIXIS_LBMAP_MASK	0xf0
 #define PIXIS_LBMAP_SHIFT	4
 #define PIXIS_LBMAP_ALTBANK	0x40

 #define CONFIG_SYS_FLASH_QUIET_TEST
 #define CONFIG_FLASH_SHOW_PROGRESS 	45 /* count down from 45/5: 9..1 */

 #define CONFIG_SYS_MAX_FLASH_BANKS	2		/* number of banks */
 #define CONFIG_SYS_MAX_FLASH_SECT	1024		/* sectors per device */
 #define CONFIG_SYS_FLASH_ERASE_TOUT	60000		/* Flash Erase Timeout (ms) */
 #define CONFIG_SYS_FLASH_WRITE_TOUT	500		/* Flash Write Timeout (ms) */

 #define CONFIG_SYS_MONITOR_BASE		CONFIG_SYS_TEXT_BASE	/* start of monitor */

 #if defined(CONFIG_RAMBOOT_PBL)
 #define CONFIG_SYS_RAMBOOT
 #endif

 /* Nand Flash */
 #ifdef CONFIG_NAND_FSL_ELBC
 #define CONFIG_SYS_NAND_BASE		0xffa00000
 #ifdef CONFIG_PHYS_64BIT
 #define CONFIG_SYS_NAND_BASE_PHYS	0xfffa00000ull
 #else
 #define CONFIG_SYS_NAND_BASE_PHYS	CONFIG_SYS_NAND_BASE
 #endif

 #define CONFIG_SYS_NAND_BASE_LIST     {CONFIG_SYS_NAND_BASE}
 #define CONFIG_SYS_MAX_NAND_DEVICE	1
 #define CONFIG_SYS_NAND_BLOCK_SIZE    (128 * 1024)

 /* NAND flash config */
 #define CONFIG_SYS_NAND_BR_PRELIM  (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
 			       | (2<<BR_DECC_SHIFT)    /* Use HW ECC */ \
 			       | BR_PS_8	       /* Port Size = 8 bit */ \
 			       | BR_MS_FCM	       /* MSEL = FCM */ \
 			       | BR_V)		       /* valid */
 #define CONFIG_SYS_NAND_OR_PRELIM  (0xFFFC0000	      /* length 256K */ \
 			       | OR_FCM_PGS	       /* Large Page*/ \
 			       | OR_FCM_CSCT \
 			       | OR_FCM_CST \
 			       | OR_FCM_CHT \
 			       | OR_FCM_SCY_1 \
 			       | OR_FCM_TRLX \
 			       | OR_FCM_EHTR)

 #ifdef CONFIG_MTD_RAW_NAND
 #define CONFIG_SYS_BR0_PRELIM  CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */
 #define CONFIG_SYS_OR0_PRELIM  CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */
 #define CONFIG_SYS_BR2_PRELIM  CONFIG_SYS_FLASH_BR_PRELIM /* NOR Base Address */
 #define CONFIG_SYS_OR2_PRELIM  CONFIG_SYS_FLASH_OR_PRELIM /* NOR Options */
 #else
 #define CONFIG_SYS_BR0_PRELIM  CONFIG_SYS_FLASH_BR_PRELIM /* NOR Base Address */
 #define CONFIG_SYS_OR0_PRELIM  CONFIG_SYS_FLASH_OR_PRELIM /* NOR Options */
 #define CONFIG_SYS_BR2_PRELIM  CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */
 #define CONFIG_SYS_OR2_PRELIM  CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */
 #endif
 #else
 #define CONFIG_SYS_BR0_PRELIM  CONFIG_SYS_FLASH_BR_PRELIM /* NOR Base Address */
 #define CONFIG_SYS_OR0_PRELIM  CONFIG_SYS_FLASH_OR_PRELIM /* NOR Options */
 #endif /* CONFIG_NAND_FSL_ELBC */

 #define CONFIG_SYS_FLASH_EMPTY_INFO
 #define CONFIG_SYS_FLASH_AMD_CHECK_DQ7
 #define CONFIG_SYS_FLASH_BANKS_LIST	{CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000, CONFIG_SYS_FLASH_BASE_PHYS}

 #define CONFIG_HWCONFIG

 /* define to use L1 as initial stack */
 #define CONFIG_L1_INIT_RAM
 #define CONFIG_SYS_INIT_RAM_LOCK
 #define CONFIG_SYS_INIT_RAM_ADDR	0xfdd00000	/* Initial L1 address */
 #ifdef CONFIG_PHYS_64BIT
 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf
 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR
 /* The assembler doesn't like typecast */
 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
 	((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
 	  CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
 #else
 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS	CONFIG_SYS_INIT_RAM_ADDR /* Initial L1 address */
 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0
 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS
 #endif
 #define CONFIG_SYS_INIT_RAM_SIZE		0x00004000	/* Size of used area in RAM */

 #define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET

 #define CONFIG_SYS_MONITOR_LEN		(768 * 1024)

 /* Serial Port - controlled on board with jumper J8
  * open - index 2
  * shorted - index 1
  */
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE	1
 #define CONFIG_SYS_NS16550_CLK		(get_bus_freq(0)/2)

 #define CONFIG_SYS_BAUDRATE_TABLE	\
 	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}

 #define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_CCSRBAR+0x11C500)
 #define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_CCSRBAR+0x11C600)
 #define CONFIG_SYS_NS16550_COM3	(CONFIG_SYS_CCSRBAR+0x11D500)
 #define CONFIG_SYS_NS16550_COM4	(CONFIG_SYS_CCSRBAR+0x11D600)

 /* I2C */

 /*
  * RapidIO
  */
 #define CONFIG_SYS_SRIO1_MEM_VIRT	0xa0000000
 #ifdef CONFIG_PHYS_64BIT
 #define CONFIG_SYS_SRIO1_MEM_PHYS	0xc20000000ull
 #else
 #define CONFIG_SYS_SRIO1_MEM_PHYS	0xa0000000
 #endif
 #define CONFIG_SYS_SRIO1_MEM_SIZE	0x10000000	/* 256M */

 #define CONFIG_SYS_SRIO2_MEM_VIRT	0xb0000000
 #ifdef CONFIG_PHYS_64BIT
 #define CONFIG_SYS_SRIO2_MEM_PHYS	0xc30000000ull
 #else
 #define CONFIG_SYS_SRIO2_MEM_PHYS	0xb0000000
 #endif
 #define CONFIG_SYS_SRIO2_MEM_SIZE	0x10000000	/* 256M */

 /*
  * for slave u-boot IMAGE instored in master memory space,
  * PHYS must be aligned based on the SIZE
  */
 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef200000ull
 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff00000ull
 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x100000	/* 1M */
 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff00000ull
 /*
  * for slave UCODE and ENV instored in master memory space,
  * PHYS must be aligned based on the SIZE
  */
 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef100000ull
 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull
 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000	/* 256K */

 /* slave core release by master*/
 #define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4
 #define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */

 /*
  * SRIO_PCIE_BOOT - SLAVE
  */
 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000
 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \
 		(0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR)
 #endif

 /*
  * eSPI - Enhanced SPI
  */

 /*
  * General PCI
  * Memory space is mapped 1-1, but I/O space must start from 0.
  */

 /* controller 1, direct to uli, tgtid 3, Base address 20000 */
 #define CONFIG_SYS_PCIE1_MEM_VIRT	0x80000000
 #define CONFIG_SYS_PCIE1_MEM_PHYS	0xc00000000ull
 #define CONFIG_SYS_PCIE1_IO_VIRT	0xf8000000
 #define CONFIG_SYS_PCIE1_IO_PHYS	0xff8000000ull

 /* controller 2, Slot 2, tgtid 2, Base address 201000 */
 #define CONFIG_SYS_PCIE2_MEM_VIRT	0xa0000000
 #define CONFIG_SYS_PCIE2_MEM_PHYS	0xc20000000ull
 #define CONFIG_SYS_PCIE2_IO_VIRT	0xf8010000
 #define CONFIG_SYS_PCIE2_IO_PHYS	0xff8010000ull

 /* controller 3, Slot 1, tgtid 1, Base address 202000 */
 #define CONFIG_SYS_PCIE3_MEM_VIRT	0xc0000000
 #define CONFIG_SYS_PCIE3_MEM_PHYS	0xc40000000ull
 #define CONFIG_SYS_PCIE3_IO_VIRT	0xf8020000
 #define CONFIG_SYS_PCIE3_IO_PHYS	0xff8020000ull

 /* controller 4, Base address 203000 */
 #define CONFIG_SYS_PCIE4_MEM_PHYS	0xc60000000ull
 #define CONFIG_SYS_PCIE4_IO_PHYS	0xff8030000ull

 /* Qman/Bman */
 #define CONFIG_SYS_BMAN_NUM_PORTALS	10
 #define CONFIG_SYS_BMAN_MEM_BASE	0xf4000000
 #ifdef CONFIG_PHYS_64BIT
 #define CONFIG_SYS_BMAN_MEM_PHYS	0xff4000000ull
 #else
 #define CONFIG_SYS_BMAN_MEM_PHYS	CONFIG_SYS_BMAN_MEM_BASE
 #endif
 #define CONFIG_SYS_BMAN_MEM_SIZE	0x00200000
 #define CONFIG_SYS_BMAN_SP_CENA_SIZE    0x4000
 #define CONFIG_SYS_BMAN_SP_CINH_SIZE    0x1000
 #define CONFIG_SYS_BMAN_CENA_BASE       CONFIG_SYS_BMAN_MEM_BASE
 #define CONFIG_SYS_BMAN_CENA_SIZE       (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
 #define CONFIG_SYS_BMAN_CINH_BASE       (CONFIG_SYS_BMAN_MEM_BASE + \
 					CONFIG_SYS_BMAN_CENA_SIZE)
 #define CONFIG_SYS_BMAN_CINH_SIZE       (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
 #define CONFIG_SYS_BMAN_SWP_ISDR_REG	0xE08
 #define CONFIG_SYS_QMAN_NUM_PORTALS	10
 #define CONFIG_SYS_QMAN_MEM_BASE	0xf4200000
 #ifdef CONFIG_PHYS_64BIT
 #define CONFIG_SYS_QMAN_MEM_PHYS	0xff4200000ull
 #else
 #define CONFIG_SYS_QMAN_MEM_PHYS	CONFIG_SYS_QMAN_MEM_BASE
 #endif
 #define CONFIG_SYS_QMAN_MEM_SIZE	0x00200000
 #define CONFIG_SYS_QMAN_SP_CENA_SIZE    0x4000
 #define CONFIG_SYS_QMAN_SP_CINH_SIZE    0x1000
 #define CONFIG_SYS_QMAN_CENA_BASE       CONFIG_SYS_QMAN_MEM_BASE
 #define CONFIG_SYS_QMAN_CENA_SIZE       (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
 #define CONFIG_SYS_QMAN_CINH_BASE       (CONFIG_SYS_QMAN_MEM_BASE + \
 					CONFIG_SYS_QMAN_CENA_SIZE)
 #define CONFIG_SYS_QMAN_CINH_SIZE       (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
 #define CONFIG_SYS_QMAN_SWP_ISDR_REG	0xE08

 #define CONFIG_SYS_DPAA_FMAN
 #define CONFIG_SYS_DPAA_PME
 /* Default address of microcode for the Linux Fman driver */
 #if defined(CONFIG_SPIFLASH)
 /*
  * env is stored at 0x100000, sector size is 0x10000, ucode is stored after
  * env, so we got 0x110000.
  */
 #define CONFIG_SYS_FMAN_FW_ADDR	0x110000
 #elif defined(CONFIG_SDCARD)
 /*
  * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
  * about 825KB (1650 blocks), Env is stored after the image, and the env size is
  * 0x2000 (16 blocks), 8 + 1650 + 16 = 1674, enlarge it to 1680.
  */
 #define CONFIG_SYS_FMAN_FW_ADDR	(512 * 1680)
 #elif defined(CONFIG_MTD_RAW_NAND)
 #define CONFIG_SYS_FMAN_FW_ADDR	(8 * CONFIG_SYS_NAND_BLOCK_SIZE)
 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
 /*
  * Slave has no ucode locally, it can fetch this from remote. When implementing
  * in two corenet boards, slave's ucode could be stored in master's memory
  * space, the address can be mapped from slave TLB->slave LAW->
  * slave SRIO or PCIE outbound window->master inbound window->
  * master LAW->the ucode address in master's memory space.
  */
 #define CONFIG_SYS_FMAN_FW_ADDR	0xFFE00000
 #else
 #define CONFIG_SYS_FMAN_FW_ADDR		0xEFF00000
 #endif
 #define CONFIG_SYS_QE_FMAN_FW_LENGTH	0x10000
 #define CONFIG_SYS_FDT_PAD		(0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)

 #ifdef CONFIG_PCI
 #define CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup */
 #endif	/* CONFIG_PCI */

 /* SATA */
 #ifdef CONFIG_FSL_SATA_V2
 #define CONFIG_SYS_SATA_MAX_DEVICE	2
 #define CONFIG_SATA1
 #define CONFIG_SYS_SATA1		CONFIG_SYS_MPC85xx_SATA1_ADDR
 #define CONFIG_SYS_SATA1_FLAGS		FLAGS_DMA
 #define CONFIG_SATA2
 #define CONFIG_SYS_SATA2		CONFIG_SYS_MPC85xx_SATA2_ADDR
 #define CONFIG_SYS_SATA2_FLAGS		FLAGS_DMA

 #define CONFIG_LBA48
 #endif

 #ifdef CONFIG_FMAN_ENET
 #define CONFIG_SYS_FM1_DTSEC1_PHY_ADDR	0x1c
 #define CONFIG_SYS_FM1_DTSEC2_PHY_ADDR	0x1d
 #define CONFIG_SYS_FM1_DTSEC3_PHY_ADDR	0x1e
 #define CONFIG_SYS_FM1_DTSEC4_PHY_ADDR	0x1f
 #define CONFIG_SYS_FM1_10GEC1_PHY_ADDR	4

 #define CONFIG_SYS_FM2_DTSEC1_PHY_ADDR	0x1c
 #define CONFIG_SYS_FM2_DTSEC2_PHY_ADDR	0x1d
 #define CONFIG_SYS_FM2_DTSEC3_PHY_ADDR	0x1e
 #define CONFIG_SYS_FM2_DTSEC4_PHY_ADDR	0x1f
 #define CONFIG_SYS_FM2_10GEC1_PHY_ADDR	0

 #define CONFIG_SYS_TBIPA_VALUE	8
 #define CONFIG_ETHPRIME		"FM1@DTSEC1"
 #endif

 /*
  * Environment
  */
 #define CONFIG_LOADS_ECHO		/* echo on for serial download */
 #define CONFIG_SYS_LOADS_BAUD_CHANGE	/* allow baudrate change */

 /*
 * USB
 */
 #define CONFIG_HAS_FSL_DR_USB
 #define CONFIG_HAS_FSL_MPH_USB

 #if defined(CONFIG_HAS_FSL_DR_USB) || defined(CONFIG_HAS_FSL_MPH_USB)
 #define CONFIG_USB_EHCI_FSL
 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
 #endif

 #ifdef CONFIG_MMC
 #define CONFIG_SYS_FSL_ESDHC_ADDR       CONFIG_SYS_MPC85xx_ESDHC_ADDR
 #define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT
 #endif

 /*
  * Miscellaneous configurable options
  */

 /*
  * For booting Linux, the board info and command line data
  * have to be in the first 64 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization.
  */
 #define CONFIG_SYS_BOOTMAPSZ	(64 << 20)	/* Initial Memory map for Linux*/
 #define CONFIG_SYS_BOOTM_LEN	(64 << 20)	/* Increase max gunzip size */

 #ifdef CONFIG_CMD_KGDB
 #define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
 #endif

 /*
  * Environment Configuration
  */
 #define CONFIG_ROOTPATH		"/opt/nfsroot"
 #define CONFIG_BOOTFILE		"uImage"
 #define CONFIG_UBOOTPATH	u-boot.bin	/* U-Boot image on TFTP server */

 #ifdef CONFIG_TARGET_P4080DS
 #define __USB_PHY_TYPE	ulpi
 #else
 #define __USB_PHY_TYPE	utmi
 #endif

 #define	CONFIG_EXTRA_ENV_SETTINGS				\
 	"hwconfig=fsl_ddr:ctlr_intlv=cacheline,"		\
 	"bank_intlv=cs0_cs1;"					\
 	"usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) ";"\
 	"usb2:dr_mode=peripheral,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\
 	"netdev=eth0\0"						\
 	"uboot=" __stringify(CONFIG_UBOOTPATH) "\0"		\
 	"ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0"	\
 	"tftpflash=tftpboot $loadaddr $uboot && "		\
 	"protect off $ubootaddr +$filesize && "			\
 	"erase $ubootaddr +$filesize && "			\
 	"cp.b $loadaddr $ubootaddr $filesize && "		\
 	"protect on $ubootaddr +$filesize && "			\
 	"cmp.b $loadaddr $ubootaddr $filesize\0"		\
 	"consoledev=ttyS0\0"					\
 	"ramdiskaddr=2000000\0"					\
 	"ramdiskfile=p4080ds/ramdisk.uboot\0"			\
 	"fdtaddr=1e00000\0"					\
 	"fdtfile=p4080ds/p4080ds.dtb\0"				\
 	"bdev=sda3\0"

 #define HDBOOT					\
 	"setenv bootargs root=/dev/$bdev rw "		\
 	"console=$consoledev,$baudrate $othbootargs;"	\
 	"tftp $loadaddr $bootfile;"			\
 	"tftp $fdtaddr $fdtfile;"			\
 	"bootm $loadaddr - $fdtaddr"

 #define NFSBOOTCOMMAND			\
 	"setenv bootargs root=/dev/nfs rw "	\
 	"nfsroot=$serverip:$rootpath "		\
 	"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
 	"console=$consoledev,$baudrate $othbootargs;"	\
 	"tftp $loadaddr $bootfile;"		\
 	"tftp $fdtaddr $fdtfile;"		\
 	"bootm $loadaddr - $fdtaddr"

 #define RAMBOOTCOMMAND				\
 	"setenv bootargs root=/dev/ram rw "		\
 	"console=$consoledev,$baudrate $othbootargs;"	\
 	"tftp $ramdiskaddr $ramdiskfile;"		\
 	"tftp $loadaddr $bootfile;"			\
 	"tftp $fdtaddr $fdtfile;"			\
 	"bootm $loadaddr $ramdiskaddr $fdtaddr"

 #define CONFIG_BOOTCOMMAND		HDBOOT

 #include <asm/fsl_secure_boot.h>

 #endif	/* __CONFIG_H */
	/* SPDX-License-Identifier: GPL-2.0+ */
	/*
	* Copyright 2009-2012 Freescale Semiconductor, Inc.
	* Copyright 2020 NXP
	*/

	/*
	* Corenet DS style board configuration file
	*/
	#ifndef __CONFIG_H
	#define __CONFIG_H

	#include <linux/stringify.h>

	#include "../board/freescale/common/ics307_clk.h"

	#ifdef CONFIG_RAMBOOT_PBL
	#ifdef CONFIG_NXP_ESBC
	#define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE
	#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
	#ifdef CONFIG_MTD_RAW_NAND
	#define CONFIG_RAMBOOT_NAND
	#endif
	#define CONFIG_BOOTSCRIPT_COPY_RAM
	#else
	#define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE
	#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
	#endif
	#endif

	#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
	/* Set 1M boot space */
	#define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000)
	#define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \
	(0x300000000ull \| CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR)
	#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
	#endif

	/* High Level Configuration Options */
	#define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */

	#ifndef CONFIG_RESET_VECTOR_ADDRESS
	#define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc
	#endif

	#define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */
	#define CONFIG_SYS_NUM_CPC CONFIG_SYS_NUM_DDR_CTLRS
	#define CONFIG_PCIE1 /* PCIE controller 1 */
	#define CONFIG_PCIE2 /* PCIE controller 2 */
	#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */

	#if defined(CONFIG_SPIFLASH)
	#elif defined(CONFIG_SDCARD)
	#define CONFIG_FSL_FIXED_MMC_LOCATION
	#endif

	#define CONFIG_SYS_CLK_FREQ get_board_sys_clk() /* sysclk for MPC85xx */

	/*
	* These can be toggled for performance analysis, otherwise use default.
	*/
	#define CONFIG_SYS_CACHE_STASHING
	#define CONFIG_BACKSIDE_L2_CACHE
	#define CONFIG_SYS_INIT_L2CSR0 L2CSR0_L2E
	#define CONFIG_BTB /* toggle branch predition */
	#ifdef CONFIG_DDR_ECC
	#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
	#endif

	#define CONFIG_ENABLE_36BIT_PHYS

	#define CONFIG_POST CONFIG_SYS_POST_MEMORY /* test POST memory test */

	/*
	* Config the L3 Cache as L3 SRAM
	*/
	#define CONFIG_SYS_INIT_L3_ADDR CONFIG_RAMBOOT_TEXT_BASE
	#ifdef CONFIG_PHYS_64BIT
	#define CONFIG_SYS_INIT_L3_ADDR_PHYS (0xf00000000ull \| CONFIG_RAMBOOT_TEXT_BASE)
	#else
	#define CONFIG_SYS_INIT_L3_ADDR_PHYS CONFIG_SYS_INIT_L3_ADDR
	#endif
	#define CONFIG_SYS_L3_SIZE (1024 << 10)
	#define CONFIG_SYS_INIT_L3_END (CONFIG_SYS_INIT_L3_ADDR + CONFIG_SYS_L3_SIZE)

	#ifdef CONFIG_PHYS_64BIT
	#define CONFIG_SYS_DCSRBAR 0xf0000000
	#define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull
	#endif

	/* EEPROM */
	#define CONFIG_SYS_I2C_EEPROM_NXID
	#define CONFIG_SYS_EEPROM_BUS_NUM 0

	/*
	* DDR Setup
	*/
	#define CONFIG_VERY_BIG_RAM
	#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
	#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE

	#define CONFIG_DIMM_SLOTS_PER_CTLR 1
	#define CONFIG_CHIP_SELECTS_PER_CTRL (4 * CONFIG_DIMM_SLOTS_PER_CTLR)

	#define CONFIG_SYS_SPD_BUS_NUM 1
	#define SPD_EEPROM_ADDRESS1 0x51
	#define SPD_EEPROM_ADDRESS2 0x52
	#define SPD_EEPROM_ADDRESS SPD_EEPROM_ADDRESS1 /* for p3041/p5010 */
	#define CONFIG_SYS_SDRAM_SIZE 4096 /* for fixed parameter use */

	/*
	* Local Bus Definitions
	*/

	/* Set the local bus clock 1/8 of platform clock */
	#define CONFIG_SYS_LBC_LCRR LCRR_CLKDIV_8

	#define CONFIG_SYS_FLASH_BASE 0xe0000000 /* Start of PromJet */
	#ifdef CONFIG_PHYS_64BIT
	#define CONFIG_SYS_FLASH_BASE_PHYS 0xfe0000000ull
	#else
	#define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE
	#endif

	#define CONFIG_SYS_FLASH_BR_PRELIM \
	(BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000) \
	\| BR_PS_16 \| BR_V)
	#define CONFIG_SYS_FLASH_OR_PRELIM ((0xf8000ff7 & ~OR_GPCM_SCY & ~OR_GPCM_EHTR) \
	\| OR_GPCM_SCY_8 \| OR_GPCM_EHTR_CLEAR)

	#define CONFIG_SYS_BR1_PRELIM \
	(BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) \| BR_PS_16 \| BR_V)
	#define CONFIG_SYS_OR1_PRELIM 0xf8000ff7

	#define PIXIS_BASE 0xffdf0000 /* PIXIS registers */
	#ifdef CONFIG_PHYS_64BIT
	#define PIXIS_BASE_PHYS 0xfffdf0000ull
	#else
	#define PIXIS_BASE_PHYS PIXIS_BASE
	#endif

	#define CONFIG_SYS_BR3_PRELIM (BR_PHYS_ADDR(PIXIS_BASE_PHYS) \| BR_PS_8 \| BR_V)
	#define CONFIG_SYS_OR3_PRELIM 0xffffeff7 /* 32KB but only 4k mapped */

	#define PIXIS_LBMAP_SWITCH 7
	#define PIXIS_LBMAP_MASK 0xf0
	#define PIXIS_LBMAP_SHIFT 4
	#define PIXIS_LBMAP_ALTBANK 0x40

	#define CONFIG_SYS_FLASH_QUIET_TEST
	#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */

	#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */
	#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */
	#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
	#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */

	#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */

	#if defined(CONFIG_RAMBOOT_PBL)
	#define CONFIG_SYS_RAMBOOT
	#endif

	/* Nand Flash */
	#ifdef CONFIG_NAND_FSL_ELBC
	#define CONFIG_SYS_NAND_BASE 0xffa00000
	#ifdef CONFIG_PHYS_64BIT
	#define CONFIG_SYS_NAND_BASE_PHYS 0xfffa00000ull
	#else
	#define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE
	#endif

	#define CONFIG_SYS_NAND_BASE_LIST {CONFIG_SYS_NAND_BASE}
	#define CONFIG_SYS_MAX_NAND_DEVICE 1
	#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)

	/* NAND flash config */
	#define CONFIG_SYS_NAND_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
	\| (2<<BR_DECC_SHIFT) /* Use HW ECC */ \
	\| BR_PS_8 /* Port Size = 8 bit */ \
	\| BR_MS_FCM /* MSEL = FCM */ \
	\| BR_V) /* valid */
	#define CONFIG_SYS_NAND_OR_PRELIM (0xFFFC0000 /* length 256K */ \
	\| OR_FCM_PGS /* Large Page*/ \
	\| OR_FCM_CSCT \
	\| OR_FCM_CST \
	\| OR_FCM_CHT \
	\| OR_FCM_SCY_1 \
	\| OR_FCM_TRLX \
	\| OR_FCM_EHTR)

	#ifdef CONFIG_MTD_RAW_NAND
	#define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */
	#define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */
	#define CONFIG_SYS_BR2_PRELIM CONFIG_SYS_FLASH_BR_PRELIM /* NOR Base Address */
	#define CONFIG_SYS_OR2_PRELIM CONFIG_SYS_FLASH_OR_PRELIM /* NOR Options */
	#else
	#define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_FLASH_BR_PRELIM /* NOR Base Address */
	#define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_FLASH_OR_PRELIM /* NOR Options */
	#define CONFIG_SYS_BR2_PRELIM CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */
	#define CONFIG_SYS_OR2_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */
	#endif
	#else
	#define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_FLASH_BR_PRELIM /* NOR Base Address */
	#define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_FLASH_OR_PRELIM /* NOR Options */
	#endif /* CONFIG_NAND_FSL_ELBC */

	#define CONFIG_SYS_FLASH_EMPTY_INFO
	#define CONFIG_SYS_FLASH_AMD_CHECK_DQ7
	#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000, CONFIG_SYS_FLASH_BASE_PHYS}

	#define CONFIG_HWCONFIG

	/* define to use L1 as initial stack */
	#define CONFIG_L1_INIT_RAM
	#define CONFIG_SYS_INIT_RAM_LOCK
	#define CONFIG_SYS_INIT_RAM_ADDR 0xfdd00000 /* Initial L1 address */
	#ifdef CONFIG_PHYS_64BIT
	#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf
	#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR
	/* The assembler doesn't like typecast */
	#define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
	((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) \| \
	CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
	#else
	#define CONFIG_SYS_INIT_RAM_ADDR_PHYS CONFIG_SYS_INIT_RAM_ADDR /* Initial L1 address */
	#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0
	#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS
	#endif
	#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 /* Size of used area in RAM */

	#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
	#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET

	#define CONFIG_SYS_MONITOR_LEN (768 * 1024)

	/* Serial Port - controlled on board with jumper J8
	* open - index 2
	* shorted - index 1
	*/
	#define CONFIG_SYS_NS16550_SERIAL
	#define CONFIG_SYS_NS16550_REG_SIZE 1
	#define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2)

	#define CONFIG_SYS_BAUDRATE_TABLE \
	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}

	#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500)
	#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600)
	#define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500)
	#define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600)

	/* I2C */

	/*
	* RapidIO
	*/
	#define CONFIG_SYS_SRIO1_MEM_VIRT 0xa0000000
	#ifdef CONFIG_PHYS_64BIT
	#define CONFIG_SYS_SRIO1_MEM_PHYS 0xc20000000ull
	#else
	#define CONFIG_SYS_SRIO1_MEM_PHYS 0xa0000000
	#endif
	#define CONFIG_SYS_SRIO1_MEM_SIZE 0x10000000 /* 256M */

	#define CONFIG_SYS_SRIO2_MEM_VIRT 0xb0000000
	#ifdef CONFIG_PHYS_64BIT
	#define CONFIG_SYS_SRIO2_MEM_PHYS 0xc30000000ull
	#else
	#define CONFIG_SYS_SRIO2_MEM_PHYS 0xb0000000
	#endif
	#define CONFIG_SYS_SRIO2_MEM_SIZE 0x10000000 /* 256M */

	/*
	* for slave u-boot IMAGE instored in master memory space,
	* PHYS must be aligned based on the SIZE
	*/
	#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef200000ull
	#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff00000ull
	#define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x100000 /* 1M */
	#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff00000ull
	/*
	* for slave UCODE and ENV instored in master memory space,
	* PHYS must be aligned based on the SIZE
	*/
	#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef100000ull
	#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull
	#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000 /* 256K */

	/* slave core release by master*/
	#define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4
	#define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */

	/*
	* SRIO_PCIE_BOOT - SLAVE
	*/
	#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
	#define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000
	#define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \
	(0x300000000ull \| CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR)
	#endif

	/*
	* eSPI - Enhanced SPI
	*/

	/*
	* General PCI
	* Memory space is mapped 1-1, but I/O space must start from 0.
	*/

	/* controller 1, direct to uli, tgtid 3, Base address 20000 */
	#define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000
	#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull
	#define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000
	#define CONFIG_SYS_PCIE1_IO_PHYS 0xff8000000ull

	/* controller 2, Slot 2, tgtid 2, Base address 201000 */
	#define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000
	#define CONFIG_SYS_PCIE2_MEM_PHYS 0xc20000000ull
	#define CONFIG_SYS_PCIE2_IO_VIRT 0xf8010000
	#define CONFIG_SYS_PCIE2_IO_PHYS 0xff8010000ull

	/* controller 3, Slot 1, tgtid 1, Base address 202000 */
	#define CONFIG_SYS_PCIE3_MEM_VIRT 0xc0000000
	#define CONFIG_SYS_PCIE3_MEM_PHYS 0xc40000000ull
	#define CONFIG_SYS_PCIE3_IO_VIRT 0xf8020000
	#define CONFIG_SYS_PCIE3_IO_PHYS 0xff8020000ull

	/* controller 4, Base address 203000 */
	#define CONFIG_SYS_PCIE4_MEM_PHYS 0xc60000000ull
	#define CONFIG_SYS_PCIE4_IO_PHYS 0xff8030000ull

	/* Qman/Bman */
	#define CONFIG_SYS_BMAN_NUM_PORTALS 10
	#define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000
	#ifdef CONFIG_PHYS_64BIT
	#define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull
	#else
	#define CONFIG_SYS_BMAN_MEM_PHYS CONFIG_SYS_BMAN_MEM_BASE
	#endif
	#define CONFIG_SYS_BMAN_MEM_SIZE 0x00200000
	#define CONFIG_SYS_BMAN_SP_CENA_SIZE 0x4000
	#define CONFIG_SYS_BMAN_SP_CINH_SIZE 0x1000
	#define CONFIG_SYS_BMAN_CENA_BASE CONFIG_SYS_BMAN_MEM_BASE
	#define CONFIG_SYS_BMAN_CENA_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
	#define CONFIG_SYS_BMAN_CINH_BASE (CONFIG_SYS_BMAN_MEM_BASE + \
	CONFIG_SYS_BMAN_CENA_SIZE)
	#define CONFIG_SYS_BMAN_CINH_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
	#define CONFIG_SYS_BMAN_SWP_ISDR_REG 0xE08
	#define CONFIG_SYS_QMAN_NUM_PORTALS 10
	#define CONFIG_SYS_QMAN_MEM_BASE 0xf4200000
	#ifdef CONFIG_PHYS_64BIT
	#define CONFIG_SYS_QMAN_MEM_PHYS 0xff4200000ull
	#else
	#define CONFIG_SYS_QMAN_MEM_PHYS CONFIG_SYS_QMAN_MEM_BASE
	#endif
	#define CONFIG_SYS_QMAN_MEM_SIZE 0x00200000
	#define CONFIG_SYS_QMAN_SP_CENA_SIZE 0x4000
	#define CONFIG_SYS_QMAN_SP_CINH_SIZE 0x1000
	#define CONFIG_SYS_QMAN_CENA_BASE CONFIG_SYS_QMAN_MEM_BASE
	#define CONFIG_SYS_QMAN_CENA_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
	#define CONFIG_SYS_QMAN_CINH_BASE (CONFIG_SYS_QMAN_MEM_BASE + \
	CONFIG_SYS_QMAN_CENA_SIZE)
	#define CONFIG_SYS_QMAN_CINH_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
	#define CONFIG_SYS_QMAN_SWP_ISDR_REG 0xE08

	#define CONFIG_SYS_DPAA_FMAN
	#define CONFIG_SYS_DPAA_PME
	/* Default address of microcode for the Linux Fman driver */
	#if defined(CONFIG_SPIFLASH)
	/*
	* env is stored at 0x100000, sector size is 0x10000, ucode is stored after
	* env, so we got 0x110000.
	*/
	#define CONFIG_SYS_FMAN_FW_ADDR 0x110000
	#elif defined(CONFIG_SDCARD)
	/*
	* PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
	* about 825KB (1650 blocks), Env is stored after the image, and the env size is
	* 0x2000 (16 blocks), 8 + 1650 + 16 = 1674, enlarge it to 1680.
	*/
	#define CONFIG_SYS_FMAN_FW_ADDR (512 * 1680)
	#elif defined(CONFIG_MTD_RAW_NAND)
	#define CONFIG_SYS_FMAN_FW_ADDR (8 * CONFIG_SYS_NAND_BLOCK_SIZE)
	#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
	/*
	* Slave has no ucode locally, it can fetch this from remote. When implementing
	* in two corenet boards, slave's ucode could be stored in master's memory
	* space, the address can be mapped from slave TLB->slave LAW->
	* slave SRIO or PCIE outbound window->master inbound window->
	* master LAW->the ucode address in master's memory space.
	*/
	#define CONFIG_SYS_FMAN_FW_ADDR 0xFFE00000
	#else
	#define CONFIG_SYS_FMAN_FW_ADDR 0xEFF00000
	#endif
	#define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000
	#define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)

	#ifdef CONFIG_PCI
	#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
	#endif /* CONFIG_PCI */

	/* SATA */
	#ifdef CONFIG_FSL_SATA_V2
	#define CONFIG_SYS_SATA_MAX_DEVICE 2
	#define CONFIG_SATA1
	#define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR
	#define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA
	#define CONFIG_SATA2
	#define CONFIG_SYS_SATA2 CONFIG_SYS_MPC85xx_SATA2_ADDR
	#define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA

	#define CONFIG_LBA48
	#endif

	#ifdef CONFIG_FMAN_ENET
	#define CONFIG_SYS_FM1_DTSEC1_PHY_ADDR 0x1c
	#define CONFIG_SYS_FM1_DTSEC2_PHY_ADDR 0x1d
	#define CONFIG_SYS_FM1_DTSEC3_PHY_ADDR 0x1e
	#define CONFIG_SYS_FM1_DTSEC4_PHY_ADDR 0x1f
	#define CONFIG_SYS_FM1_10GEC1_PHY_ADDR 4

	#define CONFIG_SYS_FM2_DTSEC1_PHY_ADDR 0x1c
	#define CONFIG_SYS_FM2_DTSEC2_PHY_ADDR 0x1d
	#define CONFIG_SYS_FM2_DTSEC3_PHY_ADDR 0x1e
	#define CONFIG_SYS_FM2_DTSEC4_PHY_ADDR 0x1f
	#define CONFIG_SYS_FM2_10GEC1_PHY_ADDR 0

	#define CONFIG_SYS_TBIPA_VALUE 8
	#define CONFIG_ETHPRIME "FM1@DTSEC1"
	#endif

	/*
	* Environment
	*/
	#define CONFIG_LOADS_ECHO /* echo on for serial download */
	#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */

	/*
	* USB
	*/
	#define CONFIG_HAS_FSL_DR_USB
	#define CONFIG_HAS_FSL_MPH_USB

	#if defined(CONFIG_HAS_FSL_DR_USB) \|\| defined(CONFIG_HAS_FSL_MPH_USB)
	#define CONFIG_USB_EHCI_FSL
	#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
	#endif

	#ifdef CONFIG_MMC
	#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR
	#define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT
	#endif

	/*
	* Miscellaneous configurable options
	*/

	/*
	* For booting Linux, the board info and command line data
	* have to be in the first 64 MB of memory, since this is
	* the maximum mapped by the Linux kernel during initialization.
	*/
	#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory map for Linux*/
	#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */

	#ifdef CONFIG_CMD_KGDB
	#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
	#endif

	/*
	* Environment Configuration
	*/
	#define CONFIG_ROOTPATH "/opt/nfsroot"
	#define CONFIG_BOOTFILE "uImage"
	#define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */

	#ifdef CONFIG_TARGET_P4080DS
	#define __USB_PHY_TYPE ulpi
	#else
	#define __USB_PHY_TYPE utmi
	#endif

	#define CONFIG_EXTRA_ENV_SETTINGS \
	"hwconfig=fsl_ddr:ctlr_intlv=cacheline," \
	"bank_intlv=cs0_cs1;" \
	"usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) ";"\
	"usb2:dr_mode=peripheral,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\
	"netdev=eth0\0" \
	"uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \
	"ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \
	"tftpflash=tftpboot $loadaddr $uboot && " \
	"protect off $ubootaddr +$filesize && " \
	"erase $ubootaddr +$filesize && " \
	"cp.b $loadaddr $ubootaddr $filesize && " \
	"protect on $ubootaddr +$filesize && " \
	"cmp.b $loadaddr $ubootaddr $filesize\0" \
	"consoledev=ttyS0\0" \
	"ramdiskaddr=2000000\0" \
	"ramdiskfile=p4080ds/ramdisk.uboot\0" \
	"fdtaddr=1e00000\0" \
	"fdtfile=p4080ds/p4080ds.dtb\0" \
	"bdev=sda3\0"

	#define HDBOOT \
	"setenv bootargs root=/dev/$bdev rw " \
	"console=$consoledev,$baudrate $othbootargs;" \
	"tftp $loadaddr $bootfile;" \
	"tftp $fdtaddr $fdtfile;" \
	"bootm $loadaddr - $fdtaddr"

	#define NFSBOOTCOMMAND \
	"setenv bootargs root=/dev/nfs rw " \
	"nfsroot=$serverip:$rootpath " \
	"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
	"console=$consoledev,$baudrate $othbootargs;" \
	"tftp $loadaddr $bootfile;" \
	"tftp $fdtaddr $fdtfile;" \
	"bootm $loadaddr - $fdtaddr"

	#define RAMBOOTCOMMAND \
	"setenv bootargs root=/dev/ram rw " \
	"console=$consoledev,$baudrate $othbootargs;" \
	"tftp $ramdiskaddr $ramdiskfile;" \
	"tftp $loadaddr $bootfile;" \
	"tftp $fdtaddr $fdtfile;" \
	"bootm $loadaddr $ramdiskaddr $fdtaddr"

	#define CONFIG_BOOTCOMMAND HDBOOT

	#include <asm/fsl_secure_boot.h>

	#endif /* __CONFIG_H */