include/configs/P2041RDB.h - filogic/uboot - Gitiles

 /* SPDX-License-Identifier: GPL-2.0+ */
 /*
  * Copyright 2011-2012 Freescale Semiconductor, Inc.
  * Copyright 2020-2021 NXP
  */

 /*
  * P2041 RDB board configuration file
  * Also supports P2040 RDB
  */
 #ifndef __CONFIG_H
 #define __CONFIG_H

 #ifdef CONFIG_RAMBOOT_PBL
 #define CONFIG_RAMBOOT_TEXT_BASE	CONFIG_TEXT_BASE
 #define CONFIG_RESET_VECTOR_ADDRESS	0xfffffffc
 #endif

 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
 /* Set 1M boot space */
 #define CFG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_TEXT_BASE & 0xfff00000)
 #define CFG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \
 		(0x300000000ull | CFG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR)
 #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
 #endif

 /* High Level Configuration Options */

 #ifndef CONFIG_RESET_VECTOR_ADDRESS
 #define CONFIG_RESET_VECTOR_ADDRESS	0xeffffffc
 #endif

 #define CFG_SYS_NUM_CPC		CONFIG_SYS_NUM_DDR_CTLRS

 #ifndef __ASSEMBLY__
 #include <linux/stringify.h>
 #endif

 /*
  * These can be toggled for performance analysis, otherwise use default.
  */
 #define CFG_SYS_INIT_L2CSR0		L2CSR0_L2E

 #define CONFIG_POST CFG_SYS_POST_MEMORY	/* test POST memory test */

 /*
  *  Config the L3 Cache as L3 SRAM
  */
 #define CFG_SYS_INIT_L3_ADDR		CONFIG_RAMBOOT_TEXT_BASE
 #ifdef CONFIG_PHYS_64BIT
 #define CFG_SYS_INIT_L3_ADDR_PHYS	(0xf00000000ull | \
 		CONFIG_RAMBOOT_TEXT_BASE)
 #else
 #define CFG_SYS_INIT_L3_ADDR_PHYS	CFG_SYS_INIT_L3_ADDR
 #endif

 #ifdef CONFIG_PHYS_64BIT
 #define CFG_SYS_DCSRBAR		0xf0000000
 #define CFG_SYS_DCSRBAR_PHYS		0xf00000000ull
 #endif

 /*
  * DDR Setup
  */
 #define CONFIG_VERY_BIG_RAM
 #define CFG_SYS_DDR_SDRAM_BASE	0x00000000
 #define CFG_SYS_SDRAM_BASE		CFG_SYS_DDR_SDRAM_BASE

 #define SPD_EEPROM_ADDRESS	0x52
 #define CFG_SYS_SDRAM_SIZE	4096	/* for fixed parameter use */

 /*
  * Local Bus Definitions
  */

 /* Set the local bus clock 1/8 of platform clock */
 #define CFG_SYS_LBC_LCRR		LCRR_CLKDIV_8

 /*
  * This board doesn't have a promjet connector.
  * However, it uses commone corenet board LAW and TLB.
  * It is necessary to use the same start address with proper offset.
  */
 #define CFG_SYS_FLASH_BASE		0xe0000000
 #ifdef CONFIG_PHYS_64BIT
 #define CFG_SYS_FLASH_BASE_PHYS	0xfe0000000ull
 #else
 #define CFG_SYS_FLASH_BASE_PHYS	CFG_SYS_FLASH_BASE
 #endif

 #define CONFIG_FSL_CPLD
 #define CPLD_BASE		0xffdf0000	/* CPLD registers */
 #ifdef CONFIG_PHYS_64BIT
 #define CPLD_BASE_PHYS		0xfffdf0000ull
 #else
 #define CPLD_BASE_PHYS		CPLD_BASE
 #endif

 #define PIXIS_LBMAP_SWITCH	7
 #define PIXIS_LBMAP_MASK	0xf0
 #define PIXIS_LBMAP_SHIFT	4
 #define PIXIS_LBMAP_ALTBANK	0x40

 #define CONFIG_FLASH_SHOW_PROGRESS	45 /* count down from 45/5: 9..1 */

 /* Nand Flash */
 #ifdef CONFIG_NAND_FSL_ELBC
 #define CFG_SYS_NAND_BASE		0xffa00000
 #ifdef CONFIG_PHYS_64BIT
 #define CFG_SYS_NAND_BASE_PHYS	0xfffa00000ull
 #else
 #define CFG_SYS_NAND_BASE_PHYS	CFG_SYS_NAND_BASE
 #endif

 #define CFG_SYS_NAND_BASE_LIST     {CFG_SYS_NAND_BASE}

 /* NAND flash config */
 #define CFG_SYS_NAND_BR_PRELIM  (BR_PHYS_ADDR(CFG_SYS_NAND_BASE_PHYS) \
 			       | (2<<BR_DECC_SHIFT)    /* Use HW ECC */ \
 			       | BR_PS_8	       /* Port Size = 8 bit */ \
 			       | BR_MS_FCM	       /* MSEL = FCM */ \
 			       | BR_V)		       /* valid */
 #define CFG_SYS_NAND_OR_PRELIM  (0xFFFC0000	      /* length 256K */ \
 			       | OR_FCM_PGS	       /* Large Page*/ \
 			       | OR_FCM_CSCT \
 			       | OR_FCM_CST \
 			       | OR_FCM_CHT \
 			       | OR_FCM_SCY_1 \
 			       | OR_FCM_TRLX \
 			       | OR_FCM_EHTR)
 #endif /* CONFIG_NAND_FSL_ELBC */

 #define CFG_SYS_FLASH_BANKS_LIST	{CFG_SYS_FLASH_BASE_PHYS + 0x8000000}

 /* define to use L1 as initial stack */
 #define CONFIG_L1_INIT_RAM
 #define CFG_SYS_INIT_RAM_ADDR	0xffd00000	/* Initial L1 address */
 #ifdef CONFIG_PHYS_64BIT
 #define CFG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf
 #define CFG_SYS_INIT_RAM_ADDR_PHYS_LOW CFG_SYS_INIT_RAM_ADDR
 /* The assembler doesn't like typecast */
 #define CFG_SYS_INIT_RAM_ADDR_PHYS \
 	((CFG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
 	  CFG_SYS_INIT_RAM_ADDR_PHYS_LOW)
 #else
 #define CFG_SYS_INIT_RAM_ADDR_PHYS	CFG_SYS_INIT_RAM_ADDR
 #define CFG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0
 #define CFG_SYS_INIT_RAM_ADDR_PHYS_LOW CFG_SYS_INIT_RAM_ADDR_PHYS
 #endif
 #define CFG_SYS_INIT_RAM_SIZE	0x00004000

 #define CFG_SYS_INIT_SP_OFFSET	(CFG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)

 /* Serial Port - controlled on board with jumper J8
  * open - index 2
  * shorted - index 1
  */
 #define CFG_SYS_NS16550_CLK		(get_bus_freq(0)/2)

 #define CFG_SYS_BAUDRATE_TABLE	\
 	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}

 #define CFG_SYS_NS16550_COM1	(CFG_SYS_CCSRBAR+0x11C500)
 #define CFG_SYS_NS16550_COM2	(CFG_SYS_CCSRBAR+0x11C600)
 #define CFG_SYS_NS16550_COM3	(CFG_SYS_CCSRBAR+0x11D500)
 #define CFG_SYS_NS16550_COM4	(CFG_SYS_CCSRBAR+0x11D600)

 /* I2C */


 /*
  * RapidIO
  */
 #define CFG_SYS_SRIO1_MEM_VIRT	0xa0000000
 #ifdef CONFIG_PHYS_64BIT
 #define CFG_SYS_SRIO1_MEM_PHYS	0xc20000000ull
 #else
 #define CFG_SYS_SRIO1_MEM_PHYS	0xa0000000
 #endif
 #define CFG_SYS_SRIO1_MEM_SIZE	0x10000000	/* 256M */

 #define CFG_SYS_SRIO2_MEM_VIRT	0xb0000000
 #ifdef CONFIG_PHYS_64BIT
 #define CFG_SYS_SRIO2_MEM_PHYS	0xc30000000ull
 #else
 #define CFG_SYS_SRIO2_MEM_PHYS	0xb0000000
 #endif
 #define CFG_SYS_SRIO2_MEM_SIZE	0x10000000	/* 256M */

 /*
  * for slave u-boot IMAGE instored in master memory space,
  * PHYS must be aligned based on the SIZE
  */
 #define CFG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef200000ull
 #define CFG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff00000ull
 #define CFG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x100000	/* 1M */
 #define CFG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff00000ull
 /*
  * for slave UCODE and ENV instored in master memory space,
  * PHYS must be aligned based on the SIZE
  */
 #define CFG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef100000ull
 #define CFG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull
 #define CFG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000	/* 256K */

 /* slave core release by master*/
 #define CFG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4
 #define CFG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */

 /*
  * SRIO_PCIE_BOOT - SLAVE
  */
 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
 #define CFG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000
 #define CFG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \
 		(0x300000000ull | CFG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR)
 #endif

 /*
  * eSPI - Enhanced SPI
  */

 /*
  * General PCI
  * Memory space is mapped 1-1, but I/O space must start from 0.
  */

 /* controller 1, direct to uli, tgtid 3, Base address 20000 */
 #define CFG_SYS_PCIE1_MEM_VIRT	0x80000000
 #define CFG_SYS_PCIE1_MEM_PHYS	0xc00000000ull
 #define CFG_SYS_PCIE1_IO_VIRT	0xf8000000
 #define CFG_SYS_PCIE1_IO_PHYS	0xff8000000ull

 /* controller 2, Slot 2, tgtid 2, Base address 201000 */
 #define CFG_SYS_PCIE2_MEM_VIRT	0xa0000000
 #define CFG_SYS_PCIE2_MEM_PHYS	0xc20000000ull
 #define CFG_SYS_PCIE2_IO_VIRT	0xf8010000
 #define CFG_SYS_PCIE2_IO_PHYS	0xff8010000ull

 /* controller 3, Slot 1, tgtid 1, Base address 202000 */
 #define CFG_SYS_PCIE3_MEM_VIRT	0xc0000000
 #define CFG_SYS_PCIE3_MEM_PHYS	0xc40000000ull

 /* Qman/Bman */
 #define CFG_SYS_BMAN_NUM_PORTALS	10
 #define CFG_SYS_BMAN_MEM_BASE	0xf4000000
 #ifdef CONFIG_PHYS_64BIT
 #define CFG_SYS_BMAN_MEM_PHYS	0xff4000000ull
 #else
 #define CFG_SYS_BMAN_MEM_PHYS	CFG_SYS_BMAN_MEM_BASE
 #endif
 #define CFG_SYS_BMAN_MEM_SIZE	0x00200000
 #define CFG_SYS_BMAN_SP_CENA_SIZE    0x4000
 #define CFG_SYS_BMAN_SP_CINH_SIZE    0x1000
 #define CFG_SYS_BMAN_CENA_BASE       CFG_SYS_BMAN_MEM_BASE
 #define CFG_SYS_BMAN_CENA_SIZE       (CFG_SYS_BMAN_MEM_SIZE >> 1)
 #define CFG_SYS_BMAN_CINH_BASE       (CFG_SYS_BMAN_MEM_BASE + \
 					CFG_SYS_BMAN_CENA_SIZE)
 #define CFG_SYS_BMAN_CINH_SIZE       (CFG_SYS_BMAN_MEM_SIZE >> 1)
 #define CFG_SYS_BMAN_SWP_ISDR_REG	0xE08
 #define CFG_SYS_QMAN_NUM_PORTALS	10
 #define CFG_SYS_QMAN_MEM_BASE	0xf4200000
 #ifdef CONFIG_PHYS_64BIT
 #define CFG_SYS_QMAN_MEM_PHYS	0xff4200000ull
 #else
 #define CFG_SYS_QMAN_MEM_PHYS	CFG_SYS_QMAN_MEM_BASE
 #endif
 #define CFG_SYS_QMAN_MEM_SIZE	0x00200000
 #define CFG_SYS_QMAN_SP_CINH_SIZE    0x1000
 #define CFG_SYS_QMAN_CENA_SIZE       (CFG_SYS_QMAN_MEM_SIZE >> 1)
 #define CFG_SYS_QMAN_CINH_BASE       (CFG_SYS_QMAN_MEM_BASE + \
 					CFG_SYS_QMAN_CENA_SIZE)
 #define CFG_SYS_QMAN_CINH_SIZE       (CFG_SYS_QMAN_MEM_SIZE >> 1)
 #define CFG_SYS_QMAN_SWP_ISDR_REG	0xE08

 #ifdef CONFIG_FMAN_ENET
 #define CFG_SYS_FM1_DTSEC1_PHY_ADDR	0x2
 #define CFG_SYS_FM1_DTSEC2_PHY_ADDR	0x3
 #define CFG_SYS_FM1_DTSEC3_PHY_ADDR	0x4
 #define CFG_SYS_FM1_DTSEC4_PHY_ADDR	0x1
 #define CFG_SYS_FM1_DTSEC5_PHY_ADDR	0x0

 #define CFG_SYS_FM1_DTSEC1_RISER_PHY_ADDR	0x1c
 #define CFG_SYS_FM1_DTSEC2_RISER_PHY_ADDR	0x1d
 #define CFG_SYS_FM1_DTSEC3_RISER_PHY_ADDR	0x1e
 #define CFG_SYS_FM1_DTSEC4_RISER_PHY_ADDR	0x1f

 #define CFG_SYS_FM1_10GEC1_PHY_ADDR	0

 #define CFG_SYS_TBIPA_VALUE	8
 #endif

 #ifdef CONFIG_MMC
 #define CFG_SYS_FSL_ESDHC_ADDR       CFG_SYS_MPC85xx_ESDHC_ADDR
 #endif

 /*
  * Miscellaneous configurable options
  */

 /*
  * For booting Linux, the board info and command line data
  * have to be in the first 64 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization.
  */
 #define CFG_SYS_BOOTMAPSZ	(64 << 20)	/* Initial Memory for Linux */

 /*
  * Environment Configuration
  */
 #define CONFIG_ROOTPATH		"/opt/nfsroot"
 #define CONFIG_UBOOTPATH	u-boot.bin

 #define __USB_PHY_TYPE	utmi

 #define	CONFIG_EXTRA_ENV_SETTINGS				\
 	"hwconfig=fsl_ddr:ctlr_intlv=cacheline,"		\
 	"bank_intlv=cs0_cs1\0"					\
 	"netdev=eth0\0"						\
 	"uboot=" __stringify(CONFIG_UBOOTPATH) "\0"			\
 	"ubootaddr=" __stringify(CONFIG_TEXT_BASE) "\0"		\
 	"tftpflash=tftpboot $loadaddr $uboot && "		\
 	"protect off $ubootaddr +$filesize && "			\
 	"erase $ubootaddr +$filesize && "			\
 	"cp.b $loadaddr $ubootaddr $filesize && "		\
 	"protect on $ubootaddr +$filesize && "			\
 	"cmp.b $loadaddr $ubootaddr $filesize\0"		\
 	"consoledev=ttyS0\0"					\
 	"usb_phy_type=" __stringify(__USB_PHY_TYPE) "\0"		\
 	"usb_dr_mode=host\0"					\
 	"ramdiskaddr=2000000\0"					\
 	"ramdiskfile=p2041rdb/ramdisk.uboot\0"			\
 	"fdtaddr=1e00000\0"					\
 	"fdtfile=p2041rdb/p2041rdb.dtb\0"			\
 	"bdev=sda3\0"

 #include <asm/fsl_secure_boot.h>

 #endif	/* __CONFIG_H */
	/* SPDX-License-Identifier: GPL-2.0+ */
	/*
	* Copyright 2011-2012 Freescale Semiconductor, Inc.
	* Copyright 2020-2021 NXP
	*/

	/*
	* P2041 RDB board configuration file
	* Also supports P2040 RDB
	*/
	#ifndef __CONFIG_H
	#define __CONFIG_H

	#ifdef CONFIG_RAMBOOT_PBL
	#define CONFIG_RAMBOOT_TEXT_BASE CONFIG_TEXT_BASE
	#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
	#endif

	#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
	/* Set 1M boot space */
	#define CFG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_TEXT_BASE & 0xfff00000)
	#define CFG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \
	(0x300000000ull \| CFG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR)
	#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
	#endif

	/* High Level Configuration Options */

	#ifndef CONFIG_RESET_VECTOR_ADDRESS
	#define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc
	#endif

	#define CFG_SYS_NUM_CPC CONFIG_SYS_NUM_DDR_CTLRS

	#ifndef __ASSEMBLY__
	#include <linux/stringify.h>
	#endif

	/*
	* These can be toggled for performance analysis, otherwise use default.
	*/
	#define CFG_SYS_INIT_L2CSR0 L2CSR0_L2E

	#define CONFIG_POST CFG_SYS_POST_MEMORY /* test POST memory test */

	/*
	* Config the L3 Cache as L3 SRAM
	*/
	#define CFG_SYS_INIT_L3_ADDR CONFIG_RAMBOOT_TEXT_BASE
	#ifdef CONFIG_PHYS_64BIT
	#define CFG_SYS_INIT_L3_ADDR_PHYS (0xf00000000ull \| \
	CONFIG_RAMBOOT_TEXT_BASE)
	#else
	#define CFG_SYS_INIT_L3_ADDR_PHYS CFG_SYS_INIT_L3_ADDR
	#endif

	#ifdef CONFIG_PHYS_64BIT
	#define CFG_SYS_DCSRBAR 0xf0000000
	#define CFG_SYS_DCSRBAR_PHYS 0xf00000000ull
	#endif

	/*
	* DDR Setup
	*/
	#define CONFIG_VERY_BIG_RAM
	#define CFG_SYS_DDR_SDRAM_BASE 0x00000000
	#define CFG_SYS_SDRAM_BASE CFG_SYS_DDR_SDRAM_BASE

	#define SPD_EEPROM_ADDRESS 0x52
	#define CFG_SYS_SDRAM_SIZE 4096 /* for fixed parameter use */

	/*
	* Local Bus Definitions
	*/

	/* Set the local bus clock 1/8 of platform clock */
	#define CFG_SYS_LBC_LCRR LCRR_CLKDIV_8

	/*
	* This board doesn't have a promjet connector.
	* However, it uses commone corenet board LAW and TLB.
	* It is necessary to use the same start address with proper offset.
	*/
	#define CFG_SYS_FLASH_BASE 0xe0000000
	#ifdef CONFIG_PHYS_64BIT
	#define CFG_SYS_FLASH_BASE_PHYS 0xfe0000000ull
	#else
	#define CFG_SYS_FLASH_BASE_PHYS CFG_SYS_FLASH_BASE
	#endif

	#define CONFIG_FSL_CPLD
	#define CPLD_BASE 0xffdf0000 /* CPLD registers */
	#ifdef CONFIG_PHYS_64BIT
	#define CPLD_BASE_PHYS 0xfffdf0000ull
	#else
	#define CPLD_BASE_PHYS CPLD_BASE
	#endif

	#define PIXIS_LBMAP_SWITCH 7
	#define PIXIS_LBMAP_MASK 0xf0
	#define PIXIS_LBMAP_SHIFT 4
	#define PIXIS_LBMAP_ALTBANK 0x40

	#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */

	/* Nand Flash */
	#ifdef CONFIG_NAND_FSL_ELBC
	#define CFG_SYS_NAND_BASE 0xffa00000
	#ifdef CONFIG_PHYS_64BIT
	#define CFG_SYS_NAND_BASE_PHYS 0xfffa00000ull
	#else
	#define CFG_SYS_NAND_BASE_PHYS CFG_SYS_NAND_BASE
	#endif

	#define CFG_SYS_NAND_BASE_LIST {CFG_SYS_NAND_BASE}

	/* NAND flash config */
	#define CFG_SYS_NAND_BR_PRELIM (BR_PHYS_ADDR(CFG_SYS_NAND_BASE_PHYS) \
	\| (2<<BR_DECC_SHIFT) /* Use HW ECC */ \
	\| BR_PS_8 /* Port Size = 8 bit */ \
	\| BR_MS_FCM /* MSEL = FCM */ \
	\| BR_V) /* valid */
	#define CFG_SYS_NAND_OR_PRELIM (0xFFFC0000 /* length 256K */ \
	\| OR_FCM_PGS /* Large Page*/ \
	\| OR_FCM_CSCT \
	\| OR_FCM_CST \
	\| OR_FCM_CHT \
	\| OR_FCM_SCY_1 \
	\| OR_FCM_TRLX \
	\| OR_FCM_EHTR)
	#endif /* CONFIG_NAND_FSL_ELBC */

	#define CFG_SYS_FLASH_BANKS_LIST {CFG_SYS_FLASH_BASE_PHYS + 0x8000000}

	/* define to use L1 as initial stack */
	#define CONFIG_L1_INIT_RAM
	#define CFG_SYS_INIT_RAM_ADDR 0xffd00000 /* Initial L1 address */
	#ifdef CONFIG_PHYS_64BIT
	#define CFG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf
	#define CFG_SYS_INIT_RAM_ADDR_PHYS_LOW CFG_SYS_INIT_RAM_ADDR
	/* The assembler doesn't like typecast */
	#define CFG_SYS_INIT_RAM_ADDR_PHYS \
	((CFG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) \| \
	CFG_SYS_INIT_RAM_ADDR_PHYS_LOW)
	#else
	#define CFG_SYS_INIT_RAM_ADDR_PHYS CFG_SYS_INIT_RAM_ADDR
	#define CFG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0
	#define CFG_SYS_INIT_RAM_ADDR_PHYS_LOW CFG_SYS_INIT_RAM_ADDR_PHYS
	#endif
	#define CFG_SYS_INIT_RAM_SIZE 0x00004000

	#define CFG_SYS_INIT_SP_OFFSET (CFG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)

	/* Serial Port - controlled on board with jumper J8
	* open - index 2
	* shorted - index 1
	*/
	#define CFG_SYS_NS16550_CLK (get_bus_freq(0)/2)

	#define CFG_SYS_BAUDRATE_TABLE \
	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}

	#define CFG_SYS_NS16550_COM1 (CFG_SYS_CCSRBAR+0x11C500)
	#define CFG_SYS_NS16550_COM2 (CFG_SYS_CCSRBAR+0x11C600)
	#define CFG_SYS_NS16550_COM3 (CFG_SYS_CCSRBAR+0x11D500)
	#define CFG_SYS_NS16550_COM4 (CFG_SYS_CCSRBAR+0x11D600)

	/* I2C */


	/*
	* RapidIO
	*/
	#define CFG_SYS_SRIO1_MEM_VIRT 0xa0000000
	#ifdef CONFIG_PHYS_64BIT
	#define CFG_SYS_SRIO1_MEM_PHYS 0xc20000000ull
	#else
	#define CFG_SYS_SRIO1_MEM_PHYS 0xa0000000
	#endif
	#define CFG_SYS_SRIO1_MEM_SIZE 0x10000000 /* 256M */

	#define CFG_SYS_SRIO2_MEM_VIRT 0xb0000000
	#ifdef CONFIG_PHYS_64BIT
	#define CFG_SYS_SRIO2_MEM_PHYS 0xc30000000ull
	#else
	#define CFG_SYS_SRIO2_MEM_PHYS 0xb0000000
	#endif
	#define CFG_SYS_SRIO2_MEM_SIZE 0x10000000 /* 256M */

	/*
	* for slave u-boot IMAGE instored in master memory space,
	* PHYS must be aligned based on the SIZE
	*/
	#define CFG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef200000ull
	#define CFG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff00000ull
	#define CFG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x100000 /* 1M */
	#define CFG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff00000ull
	/*
	* for slave UCODE and ENV instored in master memory space,
	* PHYS must be aligned based on the SIZE
	*/
	#define CFG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef100000ull
	#define CFG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull
	#define CFG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000 /* 256K */

	/* slave core release by master*/
	#define CFG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4
	#define CFG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */

	/*
	* SRIO_PCIE_BOOT - SLAVE
	*/
	#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
	#define CFG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000
	#define CFG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \
	(0x300000000ull \| CFG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR)
	#endif

	/*
	* eSPI - Enhanced SPI
	*/

	/*
	* General PCI
	* Memory space is mapped 1-1, but I/O space must start from 0.
	*/

	/* controller 1, direct to uli, tgtid 3, Base address 20000 */
	#define CFG_SYS_PCIE1_MEM_VIRT 0x80000000
	#define CFG_SYS_PCIE1_MEM_PHYS 0xc00000000ull
	#define CFG_SYS_PCIE1_IO_VIRT 0xf8000000
	#define CFG_SYS_PCIE1_IO_PHYS 0xff8000000ull

	/* controller 2, Slot 2, tgtid 2, Base address 201000 */
	#define CFG_SYS_PCIE2_MEM_VIRT 0xa0000000
	#define CFG_SYS_PCIE2_MEM_PHYS 0xc20000000ull
	#define CFG_SYS_PCIE2_IO_VIRT 0xf8010000
	#define CFG_SYS_PCIE2_IO_PHYS 0xff8010000ull

	/* controller 3, Slot 1, tgtid 1, Base address 202000 */
	#define CFG_SYS_PCIE3_MEM_VIRT 0xc0000000
	#define CFG_SYS_PCIE3_MEM_PHYS 0xc40000000ull

	/* Qman/Bman */
	#define CFG_SYS_BMAN_NUM_PORTALS 10
	#define CFG_SYS_BMAN_MEM_BASE 0xf4000000
	#ifdef CONFIG_PHYS_64BIT
	#define CFG_SYS_BMAN_MEM_PHYS 0xff4000000ull
	#else
	#define CFG_SYS_BMAN_MEM_PHYS CFG_SYS_BMAN_MEM_BASE
	#endif
	#define CFG_SYS_BMAN_MEM_SIZE 0x00200000
	#define CFG_SYS_BMAN_SP_CENA_SIZE 0x4000
	#define CFG_SYS_BMAN_SP_CINH_SIZE 0x1000
	#define CFG_SYS_BMAN_CENA_BASE CFG_SYS_BMAN_MEM_BASE
	#define CFG_SYS_BMAN_CENA_SIZE (CFG_SYS_BMAN_MEM_SIZE >> 1)
	#define CFG_SYS_BMAN_CINH_BASE (CFG_SYS_BMAN_MEM_BASE + \
	CFG_SYS_BMAN_CENA_SIZE)
	#define CFG_SYS_BMAN_CINH_SIZE (CFG_SYS_BMAN_MEM_SIZE >> 1)
	#define CFG_SYS_BMAN_SWP_ISDR_REG 0xE08
	#define CFG_SYS_QMAN_NUM_PORTALS 10
	#define CFG_SYS_QMAN_MEM_BASE 0xf4200000
	#ifdef CONFIG_PHYS_64BIT
	#define CFG_SYS_QMAN_MEM_PHYS 0xff4200000ull
	#else
	#define CFG_SYS_QMAN_MEM_PHYS CFG_SYS_QMAN_MEM_BASE
	#endif
	#define CFG_SYS_QMAN_MEM_SIZE 0x00200000
	#define CFG_SYS_QMAN_SP_CINH_SIZE 0x1000
	#define CFG_SYS_QMAN_CENA_SIZE (CFG_SYS_QMAN_MEM_SIZE >> 1)
	#define CFG_SYS_QMAN_CINH_BASE (CFG_SYS_QMAN_MEM_BASE + \
	CFG_SYS_QMAN_CENA_SIZE)
	#define CFG_SYS_QMAN_CINH_SIZE (CFG_SYS_QMAN_MEM_SIZE >> 1)
	#define CFG_SYS_QMAN_SWP_ISDR_REG 0xE08

	#ifdef CONFIG_FMAN_ENET
	#define CFG_SYS_FM1_DTSEC1_PHY_ADDR 0x2
	#define CFG_SYS_FM1_DTSEC2_PHY_ADDR 0x3
	#define CFG_SYS_FM1_DTSEC3_PHY_ADDR 0x4
	#define CFG_SYS_FM1_DTSEC4_PHY_ADDR 0x1
	#define CFG_SYS_FM1_DTSEC5_PHY_ADDR 0x0

	#define CFG_SYS_FM1_DTSEC1_RISER_PHY_ADDR 0x1c
	#define CFG_SYS_FM1_DTSEC2_RISER_PHY_ADDR 0x1d
	#define CFG_SYS_FM1_DTSEC3_RISER_PHY_ADDR 0x1e
	#define CFG_SYS_FM1_DTSEC4_RISER_PHY_ADDR 0x1f

	#define CFG_SYS_FM1_10GEC1_PHY_ADDR 0

	#define CFG_SYS_TBIPA_VALUE 8
	#endif

	#ifdef CONFIG_MMC
	#define CFG_SYS_FSL_ESDHC_ADDR CFG_SYS_MPC85xx_ESDHC_ADDR
	#endif

	/*
	* Miscellaneous configurable options
	*/

	/*
	* For booting Linux, the board info and command line data
	* have to be in the first 64 MB of memory, since this is
	* the maximum mapped by the Linux kernel during initialization.
	*/
	#define CFG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory for Linux */

	/*
	* Environment Configuration
	*/
	#define CONFIG_ROOTPATH "/opt/nfsroot"
	#define CONFIG_UBOOTPATH u-boot.bin

	#define __USB_PHY_TYPE utmi

	#define CONFIG_EXTRA_ENV_SETTINGS \
	"hwconfig=fsl_ddr:ctlr_intlv=cacheline," \
	"bank_intlv=cs0_cs1\0" \
	"netdev=eth0\0" \
	"uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \
	"ubootaddr=" __stringify(CONFIG_TEXT_BASE) "\0" \
	"tftpflash=tftpboot $loadaddr $uboot && " \
	"protect off $ubootaddr +$filesize && " \
	"erase $ubootaddr +$filesize && " \
	"cp.b $loadaddr $ubootaddr $filesize && " \
	"protect on $ubootaddr +$filesize && " \
	"cmp.b $loadaddr $ubootaddr $filesize\0" \
	"consoledev=ttyS0\0" \
	"usb_phy_type=" __stringify(__USB_PHY_TYPE) "\0" \
	"usb_dr_mode=host\0" \
	"ramdiskaddr=2000000\0" \
	"ramdiskfile=p2041rdb/ramdisk.uboot\0" \
	"fdtaddr=1e00000\0" \
	"fdtfile=p2041rdb/p2041rdb.dtb\0" \
	"bdev=sda3\0"

	#include <asm/fsl_secure_boot.h>

	#endif /* __CONFIG_H */