| menu "ARM architecture" |
| depends on ARM |
| |
| config SYS_ARCH |
| default "arm" |
| |
| config ARM64 |
| bool |
| select PHYS_64BIT |
| select SYS_CACHE_SHIFT_6 |
| |
| if ARM64 |
| config POSITION_INDEPENDENT |
| bool "Generate position-independent pre-relocation code" |
| select INIT_SP_RELATIVE |
| help |
| U-Boot expects to be linked to a specific hard-coded address, and to |
| be loaded to and run from that address. This option lifts that |
| restriction, thus allowing the code to be loaded to and executed from |
| almost any 4K aligned address. This logic relies on the relocation |
| information that is embedded in the binary to support U-Boot |
| relocating itself to the top-of-RAM later during execution. |
| |
| config INIT_SP_RELATIVE |
| bool "Specify the early stack pointer relative to the .bss section" |
| help |
| U-Boot typically uses a hard-coded value for the stack pointer |
| before relocation. Enable this option to instead calculate the |
| initial SP at run-time. This is useful to avoid hard-coding addresses |
| into U-Boot, so that it can be loaded and executed at arbitrary |
| addresses and thus avoid using arbitrary addresses at runtime. |
| |
| If this option is enabled, the early stack pointer is set to |
| &_bss_start with a offset value added. The offset is specified by |
| SYS_INIT_SP_BSS_OFFSET. |
| |
| config SYS_INIT_SP_BSS_OFFSET |
| int "Early stack offset from the .bss base address" |
| depends on INIT_SP_RELATIVE |
| default 524288 |
| help |
| This option's value is the offset added to &_bss_start in order to |
| calculate the stack pointer. This offset should be large enough so |
| that the early malloc region, global data (gd), and early stack usage |
| do not overlap any appended DTB. |
| |
| config LINUX_KERNEL_IMAGE_HEADER |
| bool |
| help |
| Place a Linux kernel image header at the start of the U-Boot binary. |
| The format of the header is described in the Linux kernel source at |
| Documentation/arm64/booting.txt. This feature is useful since the |
| image header reports the amount of memory (BSS and similar) that |
| U-Boot needs to use, but which isn't part of the binary. |
| |
| if LINUX_KERNEL_IMAGE_HEADER |
| config LNX_KRNL_IMG_TEXT_OFFSET_BASE |
| hex |
| help |
| The value subtracted from CONFIG_SYS_TEXT_BASE to calculate the |
| TEXT_OFFSET value written to the Linux kernel image header. |
| endif |
| endif |
| |
| config GIC_V3_ITS |
| bool "ARM GICV3 ITS" |
| select REGMAP |
| select SYSCON |
| help |
| ARM GICV3 Interrupt translation service (ITS). |
| Basic support for programming locality specific peripheral |
| interrupts (LPI) configuration tables and enable LPI tables. |
| LPI configuration table can be used by u-boot or Linux. |
| ARM GICV3 has limitation, once the LPI table is enabled, LPI |
| configuration table can not be re-programmed, unless GICV3 reset. |
| |
| config STATIC_RELA |
| bool |
| default y if ARM64 && !POSITION_INDEPENDENT |
| |
| config DMA_ADDR_T_64BIT |
| bool |
| default y if ARM64 |
| |
| config HAS_VBAR |
| bool |
| |
| config HAS_THUMB2 |
| bool |
| |
| # Used for compatibility with asm files copied from the kernel |
| config ARM_ASM_UNIFIED |
| bool |
| default y |
| |
| # Used for compatibility with asm files copied from the kernel |
| config THUMB2_KERNEL |
| bool |
| |
| config SYS_ICACHE_OFF |
| bool "Do not enable icache" |
| default n |
| help |
| Do not enable instruction cache in U-Boot. |
| |
| config SPL_SYS_ICACHE_OFF |
| bool "Do not enable icache in SPL" |
| depends on SPL |
| default SYS_ICACHE_OFF |
| help |
| Do not enable instruction cache in SPL. |
| |
| config SYS_DCACHE_OFF |
| bool "Do not enable dcache" |
| default n |
| help |
| Do not enable data cache in U-Boot. |
| |
| config SPL_SYS_DCACHE_OFF |
| bool "Do not enable dcache in SPL" |
| depends on SPL |
| default SYS_DCACHE_OFF |
| help |
| Do not enable data cache in SPL. |
| |
| config SYS_ARM_CACHE_CP15 |
| bool "CP15 based cache enabling support" |
| help |
| Select this if your processor suports enabling caches by using |
| CP15 registers. |
| |
| config SYS_ARM_MMU |
| bool "MMU-based Paged Memory Management Support" |
| select SYS_ARM_CACHE_CP15 |
| help |
| Select if you want MMU-based virtualised addressing space |
| support via paged memory management. |
| |
| config SYS_ARM_MPU |
| bool 'Use the ARM v7 PMSA Compliant MPU' |
| help |
| Some ARM systems without an MMU have instead a Memory Protection |
| Unit (MPU) that defines the type and permissions for regions of |
| memory. |
| If your CPU has an MPU then you should choose 'y' here unless you |
| know that you do not want to use the MPU. |
| |
| # If set, the workarounds for these ARM errata are applied early during U-Boot |
| # startup. Note that in general these options force the workarounds to be |
| # applied; no CPU-type/version detection exists, unlike the similar options in |
| # the Linux kernel. Do not set these options unless they apply! Also note that |
| # the following can be machine-specific errata. These do have ability to |
| # provide rudimentary version and machine-specific checks, but expect no |
| # product checks: |
| # CONFIG_ARM_ERRATA_430973 |
| # CONFIG_ARM_ERRATA_454179 |
| # CONFIG_ARM_ERRATA_621766 |
| # CONFIG_ARM_ERRATA_798870 |
| # CONFIG_ARM_ERRATA_801819 |
| # CONFIG_ARM_CORTEX_A8_CVE_2017_5715 |
| # CONFIG_ARM_CORTEX_A15_CVE_2017_5715 |
| |
| config ARM_ERRATA_430973 |
| bool |
| |
| config ARM_ERRATA_454179 |
| bool |
| |
| config ARM_ERRATA_621766 |
| bool |
| |
| config ARM_ERRATA_716044 |
| bool |
| |
| config ARM_ERRATA_725233 |
| bool |
| |
| config ARM_ERRATA_742230 |
| bool |
| |
| config ARM_ERRATA_743622 |
| bool |
| |
| config ARM_ERRATA_751472 |
| bool |
| |
| config ARM_ERRATA_761320 |
| bool |
| |
| config ARM_ERRATA_773022 |
| bool |
| |
| config ARM_ERRATA_774769 |
| bool |
| |
| config ARM_ERRATA_794072 |
| bool |
| |
| config ARM_ERRATA_798870 |
| bool |
| |
| config ARM_ERRATA_801819 |
| bool |
| |
| config ARM_ERRATA_826974 |
| bool |
| |
| config ARM_ERRATA_828024 |
| bool |
| |
| config ARM_ERRATA_829520 |
| bool |
| |
| config ARM_ERRATA_833069 |
| bool |
| |
| config ARM_ERRATA_833471 |
| bool |
| |
| config ARM_ERRATA_845369 |
| bool |
| |
| config ARM_ERRATA_852421 |
| bool |
| |
| config ARM_ERRATA_852423 |
| bool |
| |
| config ARM_ERRATA_855873 |
| bool |
| |
| config ARM_CORTEX_A8_CVE_2017_5715 |
| bool |
| |
| config ARM_CORTEX_A15_CVE_2017_5715 |
| bool |
| |
| config CPU_ARM720T |
| bool |
| select SYS_CACHE_SHIFT_5 |
| imply SYS_ARM_MMU |
| |
| config CPU_ARM920T |
| bool |
| select SYS_CACHE_SHIFT_5 |
| imply SYS_ARM_MMU |
| |
| config CPU_ARM926EJS |
| bool |
| select SYS_CACHE_SHIFT_5 |
| imply SYS_ARM_MMU |
| |
| config CPU_ARM946ES |
| bool |
| select SYS_CACHE_SHIFT_5 |
| imply SYS_ARM_MMU |
| |
| config CPU_ARM1136 |
| bool |
| select SYS_CACHE_SHIFT_5 |
| imply SYS_ARM_MMU |
| |
| config CPU_ARM1176 |
| bool |
| select HAS_VBAR |
| select SYS_CACHE_SHIFT_5 |
| imply SYS_ARM_MMU |
| |
| config CPU_V7A |
| bool |
| select HAS_THUMB2 |
| select HAS_VBAR |
| select SYS_CACHE_SHIFT_6 |
| imply SYS_ARM_MMU |
| |
| config CPU_V7M |
| bool |
| select HAS_THUMB2 |
| select SYS_ARM_MPU |
| select SYS_CACHE_SHIFT_5 |
| select SYS_THUMB_BUILD |
| select THUMB2_KERNEL |
| |
| config CPU_V7R |
| bool |
| select HAS_THUMB2 |
| select SYS_ARM_CACHE_CP15 |
| select SYS_ARM_MPU |
| select SYS_CACHE_SHIFT_6 |
| |
| config CPU_PXA |
| bool |
| select SYS_CACHE_SHIFT_5 |
| imply SYS_ARM_MMU |
| |
| config CPU_SA1100 |
| bool |
| select SYS_CACHE_SHIFT_5 |
| imply SYS_ARM_MMU |
| |
| config SYS_CPU |
| default "arm720t" if CPU_ARM720T |
| default "arm920t" if CPU_ARM920T |
| default "arm926ejs" if CPU_ARM926EJS |
| default "arm946es" if CPU_ARM946ES |
| default "arm1136" if CPU_ARM1136 |
| default "arm1176" if CPU_ARM1176 |
| default "armv7" if CPU_V7A |
| default "armv7" if CPU_V7R |
| default "armv7m" if CPU_V7M |
| default "pxa" if CPU_PXA |
| default "sa1100" if CPU_SA1100 |
| default "armv8" if ARM64 |
| |
| config SYS_ARM_ARCH |
| int |
| default 4 if CPU_ARM720T |
| default 4 if CPU_ARM920T |
| default 5 if CPU_ARM926EJS |
| default 5 if CPU_ARM946ES |
| default 6 if CPU_ARM1136 |
| default 6 if CPU_ARM1176 |
| default 7 if CPU_V7A |
| default 7 if CPU_V7M |
| default 7 if CPU_V7R |
| default 5 if CPU_PXA |
| default 4 if CPU_SA1100 |
| default 8 if ARM64 |
| |
| config SYS_CACHE_SHIFT_5 |
| bool |
| |
| config SYS_CACHE_SHIFT_6 |
| bool |
| |
| config SYS_CACHE_SHIFT_7 |
| bool |
| |
| config SYS_CACHELINE_SIZE |
| int |
| default 128 if SYS_CACHE_SHIFT_7 |
| default 64 if SYS_CACHE_SHIFT_6 |
| default 32 if SYS_CACHE_SHIFT_5 |
| |
| choice |
| prompt "Select the ARM data write cache policy" |
| default SYS_ARM_CACHE_WRITETHROUGH if TARGET_BCMCYGNUS || \ |
| TARGET_BCMNSP || CPU_PXA || RZA1 |
| default SYS_ARM_CACHE_WRITEBACK |
| |
| config SYS_ARM_CACHE_WRITEBACK |
| bool "Write-back (WB)" |
| help |
| A write updates the cache only and marks the cache line as dirty. |
| External memory is updated only when the line is evicted or explicitly |
| cleaned. |
| |
| config SYS_ARM_CACHE_WRITETHROUGH |
| bool "Write-through (WT)" |
| help |
| A write updates both the cache and the external memory system. |
| This does not mark the cache line as dirty. |
| |
| config SYS_ARM_CACHE_WRITEALLOC |
| bool "Write allocation (WA)" |
| help |
| A cache line is allocated on a write miss. This means that executing a |
| store instruction on the processor might cause a burst read to occur. |
| There is a linefill to obtain the data for the cache line, before the |
| write is performed. |
| endchoice |
| |
| config ARCH_CPU_INIT |
| bool "Enable ARCH_CPU_INIT" |
| help |
| Some architectures require a call to arch_cpu_init(). |
| Say Y here to enable it |
| |
| config SYS_ARCH_TIMER |
| bool "ARM Generic Timer support" |
| depends on CPU_V7A || ARM64 |
| default y if ARM64 |
| help |
| The ARM Generic Timer (aka arch-timer) provides an architected |
| interface to a timer source on an SoC. |
| It is mandatory for ARMv8 implementation and widely available |
| on ARMv7 systems. |
| |
| config ARM_SMCCC |
| bool "Support for ARM SMC Calling Convention (SMCCC)" |
| depends on CPU_V7A || ARM64 |
| select ARM_PSCI_FW |
| help |
| Say Y here if you want to enable ARM SMC Calling Convention. |
| This should be enabled if U-Boot needs to communicate with system |
| firmware (for example, PSCI) according to SMCCC. |
| |
| config SEMIHOSTING |
| bool "support boot from semihosting" |
| help |
| In emulated environments, semihosting is a way for |
| the hosted environment to call out to the emulator to |
| retrieve files from the host machine. |
| |
| config SYS_THUMB_BUILD |
| bool "Build U-Boot using the Thumb instruction set" |
| depends on !ARM64 |
| help |
| Use this flag to build U-Boot using the Thumb instruction set for |
| ARM architectures. Thumb instruction set provides better code |
| density. For ARM architectures that support Thumb2 this flag will |
| result in Thumb2 code generated by GCC. |
| |
| config SPL_SYS_THUMB_BUILD |
| bool "Build SPL using the Thumb instruction set" |
| default y if SYS_THUMB_BUILD |
| depends on !ARM64 && SPL |
| help |
| Use this flag to build SPL using the Thumb instruction set for |
| ARM architectures. Thumb instruction set provides better code |
| density. For ARM architectures that support Thumb2 this flag will |
| result in Thumb2 code generated by GCC. |
| |
| config TPL_SYS_THUMB_BUILD |
| bool "Build TPL using the Thumb instruction set" |
| default y if SYS_THUMB_BUILD |
| depends on TPL && !ARM64 |
| help |
| Use this flag to build TPL using the Thumb instruction set for |
| ARM architectures. Thumb instruction set provides better code |
| density. For ARM architectures that support Thumb2 this flag will |
| result in Thumb2 code generated by GCC. |
| |
| |
| config SYS_L2CACHE_OFF |
| bool "L2cache off" |
| help |
| If SoC does not support L2CACHE or one does not want to enable |
| L2CACHE, choose this option. |
| |
| config ENABLE_ARM_SOC_BOOT0_HOOK |
| bool "prepare BOOT0 header" |
| help |
| If the SoC's BOOT0 requires a header area filled with (magic) |
| values, then choose this option, and create a file included as |
| <asm/arch/boot0.h> which contains the required assembler code. |
| |
| config ARM_CORTEX_CPU_IS_UP |
| bool |
| default n |
| |
| config USE_ARCH_MEMCPY |
| bool "Use an assembly optimized implementation of memcpy" |
| default y |
| depends on !ARM64 |
| help |
| Enable the generation of an optimized version of memcpy. |
| Such an implementation may be faster under some conditions |
| but may increase the binary size. |
| |
| config SPL_USE_ARCH_MEMCPY |
| bool "Use an assembly optimized implementation of memcpy for SPL" |
| default y if USE_ARCH_MEMCPY |
| depends on !ARM64 && SPL |
| help |
| Enable the generation of an optimized version of memcpy. |
| Such an implementation may be faster under some conditions |
| but may increase the binary size. |
| |
| config TPL_USE_ARCH_MEMCPY |
| bool "Use an assembly optimized implementation of memcpy for TPL" |
| default y if USE_ARCH_MEMCPY |
| depends on !ARM64 && TPL |
| help |
| Enable the generation of an optimized version of memcpy. |
| Such an implementation may be faster under some conditions |
| but may increase the binary size. |
| |
| config USE_ARCH_MEMSET |
| bool "Use an assembly optimized implementation of memset" |
| default y |
| depends on !ARM64 |
| help |
| Enable the generation of an optimized version of memset. |
| Such an implementation may be faster under some conditions |
| but may increase the binary size. |
| |
| config SPL_USE_ARCH_MEMSET |
| bool "Use an assembly optimized implementation of memset for SPL" |
| default y if USE_ARCH_MEMSET |
| depends on !ARM64 && SPL |
| help |
| Enable the generation of an optimized version of memset. |
| Such an implementation may be faster under some conditions |
| but may increase the binary size. |
| |
| config TPL_USE_ARCH_MEMSET |
| bool "Use an assembly optimized implementation of memset for TPL" |
| default y if USE_ARCH_MEMSET |
| depends on !ARM64 && TPL |
| help |
| Enable the generation of an optimized version of memset. |
| Such an implementation may be faster under some conditions |
| but may increase the binary size. |
| |
| config ARM64_SUPPORT_AARCH32 |
| bool "ARM64 system support AArch32 execution state" |
| depends on ARM64 |
| default y if !TARGET_THUNDERX_88XX |
| help |
| This ARM64 system supports AArch32 execution state. |
| |
| choice |
| prompt "Target select" |
| default TARGET_HIKEY |
| |
| config ARCH_AT91 |
| bool "Atmel AT91" |
| select SPL_BOARD_INIT if SPL && !TARGET_SMARTWEB |
| select SPL_SEPARATE_BSS if SPL |
| |
| config TARGET_EDB93XX |
| bool "Support edb93xx" |
| select CPU_ARM920T |
| select PL010_SERIAL |
| |
| config TARGET_ASPENITE |
| bool "Support aspenite" |
| select CPU_ARM926EJS |
| |
| config TARGET_GPLUGD |
| bool "Support gplugd" |
| select CPU_ARM926EJS |
| |
| config ARCH_DAVINCI |
| bool "TI DaVinci" |
| select CPU_ARM926EJS |
| select SPL_DM_SPI if SPL |
| imply CMD_SAVES |
| help |
| Support for TI's DaVinci platform. |
| |
| config ARCH_KIRKWOOD |
| bool "Marvell Kirkwood" |
| select ARCH_MISC_INIT |
| select BOARD_EARLY_INIT_F |
| select CPU_ARM926EJS |
| |
| config ARCH_MVEBU |
| bool "Marvell MVEBU family (Armada XP/375/38x/3700/7K/8K)" |
| select DM |
| select DM_ETH |
| select DM_SERIAL |
| select DM_SPI |
| select DM_SPI_FLASH |
| select SPL_DM_SPI if SPL |
| select SPL_DM_SPI_FLASH if SPL |
| select OF_CONTROL |
| select OF_SEPARATE |
| select SPI |
| imply CMD_DM |
| |
| config TARGET_APF27 |
| bool "Support apf27" |
| select CPU_ARM926EJS |
| select SUPPORT_SPL |
| |
| config ARCH_ORION5X |
| bool "Marvell Orion" |
| select CPU_ARM926EJS |
| |
| config TARGET_SPEAR300 |
| bool "Support spear300" |
| select BOARD_EARLY_INIT_F |
| select CPU_ARM926EJS |
| select PL011_SERIAL |
| imply CMD_SAVES |
| |
| config TARGET_SPEAR310 |
| bool "Support spear310" |
| select BOARD_EARLY_INIT_F |
| select CPU_ARM926EJS |
| select PL011_SERIAL |
| imply CMD_SAVES |
| |
| config TARGET_SPEAR320 |
| bool "Support spear320" |
| select BOARD_EARLY_INIT_F |
| select CPU_ARM926EJS |
| select PL011_SERIAL |
| imply CMD_SAVES |
| |
| config TARGET_SPEAR600 |
| bool "Support spear600" |
| select BOARD_EARLY_INIT_F |
| select CPU_ARM926EJS |
| select PL011_SERIAL |
| imply CMD_SAVES |
| |
| config TARGET_STV0991 |
| bool "Support stv0991" |
| select CPU_V7A |
| select DM |
| select DM_SERIAL |
| select DM_SPI |
| select DM_SPI_FLASH |
| select PL01X_SERIAL |
| select SPI |
| select SPI_FLASH |
| imply CMD_DM |
| |
| config TARGET_X600 |
| bool "Support x600" |
| select BOARD_LATE_INIT |
| select CPU_ARM926EJS |
| select PL011_SERIAL |
| select SUPPORT_SPL |
| |
| config TARGET_FLEA3 |
| bool "Support flea3" |
| select CPU_ARM1136 |
| |
| config TARGET_MX35PDK |
| bool "Support mx35pdk" |
| select BOARD_LATE_INIT |
| select CPU_ARM1136 |
| |
| config ARCH_BCM283X |
| bool "Broadcom BCM283X family" |
| select DM |
| select DM_GPIO |
| select DM_SERIAL |
| select OF_CONTROL |
| select PL01X_SERIAL |
| select SERIAL_SEARCH_ALL |
| imply CMD_DM |
| imply FAT_WRITE |
| |
| config ARCH_BCM63158 |
| bool "Broadcom BCM63158 family" |
| select DM |
| select OF_CONTROL |
| imply CMD_DM |
| |
| config ARCH_BCM68360 |
| bool "Broadcom BCM68360 family" |
| select DM |
| select OF_CONTROL |
| imply CMD_DM |
| |
| config ARCH_BCM6858 |
| bool "Broadcom BCM6858 family" |
| select DM |
| select OF_CONTROL |
| imply CMD_DM |
| |
| config TARGET_VEXPRESS_CA15_TC2 |
| bool "Support vexpress_ca15_tc2" |
| select CPU_V7A |
| select CPU_V7_HAS_NONSEC |
| select CPU_V7_HAS_VIRT |
| select PL011_SERIAL |
| |
| config ARCH_BCMSTB |
| bool "Broadcom BCM7XXX family" |
| select CPU_V7A |
| select DM |
| select OF_CONTROL |
| select OF_PRIOR_STAGE |
| imply CMD_DM |
| help |
| This enables support for Broadcom ARM-based set-top box |
| chipsets, including the 7445 family of chips. |
| |
| config TARGET_VEXPRESS_CA5X2 |
| bool "Support vexpress_ca5x2" |
| select CPU_V7A |
| select PL011_SERIAL |
| |
| config TARGET_VEXPRESS_CA9X4 |
| bool "Support vexpress_ca9x4" |
| select CPU_V7A |
| select PL011_SERIAL |
| |
| config TARGET_BCM23550_W1D |
| bool "Support bcm23550_w1d" |
| select CPU_V7A |
| imply CRC32_VERIFY |
| imply FAT_WRITE |
| |
| config TARGET_BCM28155_AP |
| bool "Support bcm28155_ap" |
| select CPU_V7A |
| imply CRC32_VERIFY |
| imply FAT_WRITE |
| |
| config TARGET_BCMCYGNUS |
| bool "Support bcmcygnus" |
| select CPU_V7A |
| imply BCM_SF2_ETH |
| imply BCM_SF2_ETH_GMAC |
| imply CMD_HASH |
| imply CRC32_VERIFY |
| imply FAT_WRITE |
| imply HASH_VERIFY |
| imply NETDEVICES |
| |
| config TARGET_BCMNSP |
| bool "Support bcmnsp" |
| select CPU_V7A |
| |
| config TARGET_BCMNS2 |
| bool "Support Broadcom Northstar2" |
| select ARM64 |
| help |
| Support for Broadcom Northstar 2 SoCs. NS2 is a quad-core 64-bit |
| ARMv8 Cortex-A57 processors targeting a broad range of networking |
| applications. |
| |
| config TARGET_BCMNS3 |
| bool "Support Broadcom NS3" |
| select ARM64 |
| select BOARD_LATE_INIT |
| help |
| Support for Broadcom Northstar 3 SoCs. NS3 is a octo-core 64-bit |
| ARMv8 Cortex-A72 processors targeting a broad range of networking |
| applications. |
| |
| config ARCH_EXYNOS |
| bool "Samsung EXYNOS" |
| select DM |
| select DM_GPIO |
| select DM_I2C |
| select DM_KEYBOARD |
| select DM_SERIAL |
| select DM_SPI |
| select DM_SPI_FLASH |
| select SPI |
| imply SYS_THUMB_BUILD |
| imply CMD_DM |
| imply FAT_WRITE |
| |
| config ARCH_S5PC1XX |
| bool "Samsung S5PC1XX" |
| select CPU_V7A |
| select DM |
| select DM_GPIO |
| select DM_I2C |
| select DM_SERIAL |
| imply CMD_DM |
| |
| config ARCH_HIGHBANK |
| bool "Calxeda Highbank" |
| select CPU_V7A |
| select PL011_SERIAL |
| |
| config ARCH_INTEGRATOR |
| bool "ARM Ltd. Integrator family" |
| select DM |
| select DM_SERIAL |
| select PL01X_SERIAL |
| imply CMD_DM |
| |
| config ARCH_IPQ40XX |
| bool "Qualcomm IPQ40xx SoCs" |
| select CPU_V7A |
| select DM |
| select DM_GPIO |
| select DM_SERIAL |
| select DM_RESET |
| select MSM_SMEM |
| select PINCTRL |
| select CLK |
| select SMEM |
| select OF_CONTROL |
| imply CMD_DM |
| |
| config ARCH_KEYSTONE |
| bool "TI Keystone" |
| select CMD_POWEROFF |
| select CPU_V7A |
| select SUPPORT_SPL |
| select SYS_ARCH_TIMER |
| select SYS_THUMB_BUILD |
| imply CMD_MTDPARTS |
| imply CMD_SAVES |
| imply FIT |
| |
| config ARCH_K3 |
| bool "Texas Instruments' K3 Architecture" |
| select SPL |
| select SUPPORT_SPL |
| select FIT |
| |
| config ARCH_OMAP2PLUS |
| bool "TI OMAP2+" |
| select CPU_V7A |
| select SPL_BOARD_INIT if SPL |
| select SPL_STACK_R if SPL |
| select SUPPORT_SPL |
| imply FIT |
| |
| config ARCH_MESON |
| bool "Amlogic Meson" |
| imply DISTRO_DEFAULTS |
| imply DM_RNG |
| help |
| Support for the Meson SoC family developed by Amlogic Inc., |
| targeted at media players and tablet computers. We currently |
| support the S905 (GXBaby) 64-bit SoC. |
| |
| config ARCH_MEDIATEK |
| bool "MediaTek SoCs" |
| select DM |
| select OF_CONTROL |
| select SPL_DM if SPL |
| select SPL_LIBCOMMON_SUPPORT if SPL |
| select SPL_LIBGENERIC_SUPPORT if SPL |
| select SPL_OF_CONTROL if SPL |
| select SUPPORT_SPL |
| help |
| Support for the MediaTek SoCs family developed by MediaTek Inc. |
| Please refer to doc/README.mediatek for more information. |
| |
| config ARCH_LPC32XX |
| bool "NXP LPC32xx platform" |
| select CPU_ARM926EJS |
| select DM |
| select DM_GPIO |
| select DM_SERIAL |
| select SPL_DM if SPL |
| select SUPPORT_SPL |
| imply CMD_DM |
| |
| config ARCH_IMX8 |
| bool "NXP i.MX8 platform" |
| select ARM64 |
| select DM |
| select OF_CONTROL |
| select ENABLE_ARM_SOC_BOOT0_HOOK |
| |
| config ARCH_IMX8M |
| bool "NXP i.MX8M platform" |
| select ARM64 |
| select DM |
| select SUPPORT_SPL |
| imply CMD_DM |
| |
| config ARCH_IMXRT |
| bool "NXP i.MXRT platform" |
| select CPU_V7M |
| select DM |
| select DM_SERIAL |
| select SUPPORT_SPL |
| imply CMD_DM |
| |
| config ARCH_MX23 |
| bool "NXP i.MX23 family" |
| select CPU_ARM926EJS |
| select PL011_SERIAL |
| select SUPPORT_SPL |
| |
| config ARCH_MX25 |
| bool "NXP MX25" |
| select CPU_ARM926EJS |
| imply MXC_GPIO |
| |
| config ARCH_MX28 |
| bool "NXP i.MX28 family" |
| select CPU_ARM926EJS |
| select PL011_SERIAL |
| select SUPPORT_SPL |
| |
| config ARCH_MX31 |
| bool "NXP i.MX31 family" |
| select CPU_ARM1136 |
| |
| config ARCH_MX7ULP |
| bool "NXP MX7ULP" |
| select CPU_V7A |
| select ROM_UNIFIED_SECTIONS |
| imply MXC_GPIO |
| imply SYS_THUMB_BUILD |
| |
| config ARCH_MX7 |
| bool "Freescale MX7" |
| select ARCH_MISC_INIT |
| select CPU_V7A |
| select SYS_FSL_HAS_SEC if IMX_HAB |
| select SYS_FSL_SEC_COMPAT_4 |
| select SYS_FSL_SEC_LE |
| imply BOARD_EARLY_INIT_F |
| imply MXC_GPIO |
| imply SYS_THUMB_BUILD |
| |
| config ARCH_MX6 |
| bool "Freescale MX6" |
| select CPU_V7A |
| select SYS_FSL_HAS_SEC |
| select SYS_FSL_SEC_COMPAT_4 |
| select SYS_FSL_SEC_LE |
| imply MXC_GPIO |
| imply SYS_THUMB_BUILD |
| |
| if ARCH_MX6 |
| config SPL_LDSCRIPT |
| default "arch/arm/mach-omap2/u-boot-spl.lds" |
| endif |
| |
| config ARCH_MX5 |
| bool "Freescale MX5" |
| select BOARD_EARLY_INIT_F |
| select CPU_V7A |
| imply MXC_GPIO |
| |
| config ARCH_NEXELL |
| bool "Nexell S5P4418/S5P6818 SoC" |
| select ENABLE_ARM_SOC_BOOT0_HOOK |
| select DM |
| |
| config ARCH_OWL |
| bool "Actions Semi OWL SoCs" |
| select DM |
| select DM_ETH |
| select DM_SERIAL |
| select OWL_SERIAL |
| select CLK |
| select CLK_OWL |
| select OF_CONTROL |
| select SYS_RELOC_GD_ENV_ADDR |
| imply CMD_DM |
| |
| config ARCH_QEMU |
| bool "QEMU Virtual Platform" |
| select ARCH_SUPPORT_TFABOOT |
| select DM |
| select DM_SERIAL |
| select OF_CONTROL |
| select PL01X_SERIAL |
| imply CMD_DM |
| imply DM_RTC |
| imply RTC_PL031 |
| |
| config ARCH_RMOBILE |
| bool "Renesas ARM SoCs" |
| select DM |
| select DM_SERIAL |
| imply BOARD_EARLY_INIT_F |
| imply CMD_DM |
| imply FAT_WRITE |
| imply SYS_THUMB_BUILD |
| imply ARCH_MISC_INIT if DISPLAY_CPUINFO |
| |
| config TARGET_S32V234EVB |
| bool "Support s32v234evb" |
| select ARM64 |
| select SYS_FSL_ERRATUM_ESDHC111 |
| |
| config ARCH_SNAPDRAGON |
| bool "Qualcomm Snapdragon SoCs" |
| select ARM64 |
| select DM |
| select DM_GPIO |
| select DM_SERIAL |
| select MSM_SMEM |
| select OF_CONTROL |
| select OF_SEPARATE |
| select SMEM |
| select SPMI |
| imply CMD_DM |
| |
| config ARCH_SOCFPGA |
| bool "Altera SOCFPGA family" |
| select ARCH_EARLY_INIT_R |
| select ARCH_MISC_INIT if !TARGET_SOCFPGA_ARRIA10 |
| select ARM64 if TARGET_SOCFPGA_STRATIX10 || TARGET_SOCFPGA_AGILEX |
| select CPU_V7A if TARGET_SOCFPGA_GEN5 || TARGET_SOCFPGA_ARRIA10 |
| select DM |
| select DM_SERIAL |
| select ENABLE_ARM_SOC_BOOT0_HOOK if TARGET_SOCFPGA_GEN5 || TARGET_SOCFPGA_ARRIA10 |
| select OF_CONTROL |
| select SPL_DM_RESET if DM_RESET |
| select SPL_DM_SERIAL |
| select SPL_LIBCOMMON_SUPPORT |
| select SPL_LIBGENERIC_SUPPORT |
| select SPL_NAND_SUPPORT if SPL_NAND_DENALI |
| select SPL_OF_CONTROL |
| select SPL_SEPARATE_BSS if TARGET_SOCFPGA_STRATIX10 || TARGET_SOCFPGA_AGILEX |
| select SPL_SERIAL_SUPPORT |
| select SPL_SYSRESET |
| select SPL_WATCHDOG_SUPPORT |
| select SUPPORT_SPL |
| select SYS_NS16550 |
| select SYS_THUMB_BUILD if TARGET_SOCFPGA_GEN5 || TARGET_SOCFPGA_ARRIA10 |
| select SYSRESET |
| select SYSRESET_SOCFPGA if TARGET_SOCFPGA_GEN5 || TARGET_SOCFPGA_ARRIA10 |
| select SYSRESET_SOCFPGA_SOC64 if TARGET_SOCFPGA_STRATIX10 || TARGET_SOCFPGA_AGILEX |
| imply CMD_DM |
| imply CMD_MTDPARTS |
| imply CRC32_VERIFY |
| imply DM_SPI |
| imply DM_SPI_FLASH |
| imply FAT_WRITE |
| imply SPL |
| imply SPL_DM |
| imply SPL_DM_SPI |
| imply SPL_DM_SPI_FLASH |
| imply SPL_LIBDISK_SUPPORT |
| imply SPL_MMC_SUPPORT |
| imply SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION |
| imply SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION_TYPE |
| imply SPL_SPI_FLASH_SUPPORT |
| imply SPL_SPI_SUPPORT |
| imply L2X0_CACHE |
| |
| config ARCH_SUNXI |
| bool "Support sunxi (Allwinner) SoCs" |
| select BINMAN |
| select CMD_GPIO |
| select CMD_MMC if MMC |
| select CMD_USB if DISTRO_DEFAULTS |
| select CLK |
| select DM |
| select DM_ETH |
| select DM_GPIO |
| select DM_KEYBOARD |
| select DM_MMC if MMC |
| select DM_SCSI if SCSI |
| select DM_SERIAL |
| select DM_USB if DISTRO_DEFAULTS |
| select OF_BOARD_SETUP |
| select OF_CONTROL |
| select OF_SEPARATE |
| select SPECIFY_CONSOLE_INDEX |
| select SPL_STACK_R if SPL |
| select SPL_SYS_MALLOC_SIMPLE if SPL |
| select SPL_SYS_THUMB_BUILD if !ARM64 |
| select SUNXI_GPIO |
| select SYS_NS16550 |
| select SYS_THUMB_BUILD if !ARM64 |
| select USB if DISTRO_DEFAULTS |
| select USB_KEYBOARD if DISTRO_DEFAULTS |
| select USB_STORAGE if DISTRO_DEFAULTS |
| select SPL_USE_TINY_PRINTF |
| select USE_PREBOOT |
| select SYS_RELOC_GD_ENV_ADDR |
| imply CMD_DM |
| imply CMD_GPT |
| imply CMD_UBI if MTD_RAW_NAND |
| imply DISTRO_DEFAULTS |
| imply FAT_WRITE |
| imply FIT |
| imply OF_LIBFDT_OVERLAY |
| imply PRE_CONSOLE_BUFFER |
| imply SPL_GPIO_SUPPORT |
| imply SPL_LIBCOMMON_SUPPORT |
| imply SPL_LIBGENERIC_SUPPORT |
| imply SPL_MMC_SUPPORT if MMC |
| imply SPL_POWER_SUPPORT |
| imply SPL_SERIAL_SUPPORT |
| imply USB_GADGET |
| |
| config ARCH_U8500 |
| bool "ST-Ericsson U8500 Series" |
| select CPU_V7A |
| select DM |
| select DM_GPIO |
| select DM_MMC if MMC |
| select DM_SERIAL |
| select DM_USB if USB |
| select OF_CONTROL |
| select SYSRESET |
| select TIMER |
| imply ARM_PL180_MMCI |
| imply DM_RTC |
| imply NOMADIK_MTU_TIMER |
| imply PL01X_SERIAL |
| imply RTC_PL031 |
| imply SYSRESET_SYSCON |
| |
| config ARCH_VERSAL |
| bool "Support Xilinx Versal Platform" |
| select ARM64 |
| select CLK |
| select DM |
| select DM_ETH if NET |
| select DM_MMC if MMC |
| select DM_SERIAL |
| select OF_CONTROL |
| imply BOARD_LATE_INIT |
| imply ENV_VARS_UBOOT_RUNTIME_CONFIG |
| |
| config ARCH_VF610 |
| bool "Freescale Vybrid" |
| select CPU_V7A |
| select SYS_FSL_ERRATUM_ESDHC111 |
| imply CMD_MTDPARTS |
| imply MTD_RAW_NAND |
| |
| config ARCH_ZYNQ |
| bool "Xilinx Zynq based platform" |
| select CLK |
| select CLK_ZYNQ |
| select CPU_V7A |
| select DM |
| select DM_ETH if NET |
| select DM_MMC if MMC |
| select DM_SERIAL |
| select DM_SPI |
| select DM_SPI_FLASH |
| select DM_USB if USB |
| select OF_CONTROL |
| select SPI |
| select SPL_BOARD_INIT if SPL |
| select SPL_CLK if SPL |
| select SPL_DM if SPL |
| select SPL_DM_SPI if SPL |
| select SPL_DM_SPI_FLASH if SPL |
| select SPL_OF_CONTROL if SPL |
| select SPL_SEPARATE_BSS if SPL |
| select SUPPORT_SPL |
| imply ARCH_EARLY_INIT_R |
| imply BOARD_LATE_INIT |
| imply CMD_CLK |
| imply CMD_DM |
| imply CMD_SPL |
| imply ENV_VARS_UBOOT_RUNTIME_CONFIG |
| imply FAT_WRITE |
| |
| config ARCH_ZYNQMP_R5 |
| bool "Xilinx ZynqMP R5 based platform" |
| select CLK |
| select CPU_V7R |
| select DM |
| select DM_ETH if NET |
| select DM_MMC if MMC |
| select DM_SERIAL |
| select OF_CONTROL |
| imply CMD_DM |
| imply DM_USB_GADGET |
| |
| config ARCH_ZYNQMP |
| bool "Xilinx ZynqMP based platform" |
| select ARM64 |
| select CLK |
| select DM |
| select DM_ETH if NET |
| select DM_MAILBOX |
| select DM_MMC if MMC |
| select DM_SERIAL |
| select DM_SPI if SPI |
| select DM_SPI_FLASH if DM_SPI |
| select DM_USB if USB |
| select FIRMWARE |
| select OF_CONTROL |
| select SPL_BOARD_INIT if SPL |
| select SPL_CLK if SPL |
| select SPL_DM if SPL |
| select SPL_DM_SPI if SPI && SPL_DM |
| select SPL_DM_SPI_FLASH if SPL_DM_SPI |
| select SPL_DM_MAILBOX if SPL |
| select SPL_FIRMWARE if SPL |
| select SPL_SEPARATE_BSS if SPL |
| select SUPPORT_SPL |
| select ZYNQMP_IPI |
| imply BOARD_LATE_INIT |
| imply CMD_DM |
| imply ENV_VARS_UBOOT_RUNTIME_CONFIG |
| imply FAT_WRITE |
| imply MP |
| imply DM_USB_GADGET |
| |
| config ARCH_TEGRA |
| bool "NVIDIA Tegra" |
| imply DISTRO_DEFAULTS |
| imply FAT_WRITE |
| |
| config TARGET_VEXPRESS64_AEMV8A |
| bool "Support vexpress_aemv8a" |
| select ARM64 |
| select PL01X_SERIAL |
| |
| config TARGET_VEXPRESS64_BASE_FVP |
| bool "Support Versatile Express ARMv8a FVP BASE model" |
| select ARM64 |
| select PL01X_SERIAL |
| select SEMIHOSTING |
| |
| config TARGET_VEXPRESS64_JUNO |
| bool "Support Versatile Express Juno Development Platform" |
| select ARM64 |
| select PL01X_SERIAL |
| select DM |
| select OF_CONTROL |
| select OF_BOARD |
| select CLK |
| select DM_SERIAL |
| select ARM_PSCI_FW |
| select PSCI_RESET |
| select DM_ETH |
| select BLK |
| select USB |
| select DM_USB |
| |
| config TARGET_TOTAL_COMPUTE |
| bool "Support Total Compute Platform" |
| select ARM64 |
| select PL01X_SERIAL |
| select DM |
| select DM_SERIAL |
| select DM_MMC |
| select DM_GPIO |
| |
| config TARGET_LS2080A_EMU |
| bool "Support ls2080a_emu" |
| select ARCH_LS2080A |
| select ARM64 |
| select ARMV8_MULTIENTRY |
| select FSL_DDR_SYNC_REFRESH |
| help |
| Support for Freescale LS2080A_EMU platform. |
| The LS2080A Development System (EMULATOR) is a pre-silicon |
| development platform that supports the QorIQ LS2080A |
| Layerscape Architecture processor. |
| |
| config TARGET_LS2080A_SIMU |
| bool "Support ls2080a_simu" |
| select ARCH_LS2080A |
| select ARM64 |
| select ARMV8_MULTIENTRY |
| select BOARD_LATE_INIT |
| help |
| Support for Freescale LS2080A_SIMU platform. |
| The LS2080A Development System (QDS) is a pre silicon |
| development platform that supports the QorIQ LS2080A |
| Layerscape Architecture processor. |
| |
| config TARGET_LS1088AQDS |
| bool "Support ls1088aqds" |
| select ARCH_LS1088A |
| select ARM64 |
| select ARMV8_MULTIENTRY |
| select ARCH_SUPPORT_TFABOOT |
| select BOARD_LATE_INIT |
| select SUPPORT_SPL |
| select FSL_DDR_INTERACTIVE if !SD_BOOT |
| help |
| Support for NXP LS1088AQDS platform. |
| The LS1088A Development System (QDS) is a high-performance |
| development platform that supports the QorIQ LS1088A |
| Layerscape Architecture processor. |
| |
| config TARGET_LS2080AQDS |
| bool "Support ls2080aqds" |
| select ARCH_LS2080A |
| select ARM64 |
| select ARMV8_MULTIENTRY |
| select ARCH_SUPPORT_TFABOOT |
| select BOARD_LATE_INIT |
| select SUPPORT_SPL |
| imply SCSI |
| imply SCSI_AHCI |
| select FSL_DDR_BIST |
| select FSL_DDR_INTERACTIVE if !SPL |
| help |
| Support for Freescale LS2080AQDS platform. |
| The LS2080A Development System (QDS) is a high-performance |
| development platform that supports the QorIQ LS2080A |
| Layerscape Architecture processor. |
| |
| config TARGET_LS2080ARDB |
| bool "Support ls2080ardb" |
| select ARCH_LS2080A |
| select ARM64 |
| select ARMV8_MULTIENTRY |
| select ARCH_SUPPORT_TFABOOT |
| select BOARD_LATE_INIT |
| select SUPPORT_SPL |
| select FSL_DDR_BIST |
| select FSL_DDR_INTERACTIVE if !SPL |
| imply SCSI |
| imply SCSI_AHCI |
| help |
| Support for Freescale LS2080ARDB platform. |
| The LS2080A Reference design board (RDB) is a high-performance |
| development platform that supports the QorIQ LS2080A |
| Layerscape Architecture processor. |
| |
| config TARGET_LS2081ARDB |
| bool "Support ls2081ardb" |
| select ARCH_LS2080A |
| select ARM64 |
| select ARMV8_MULTIENTRY |
| select BOARD_LATE_INIT |
| select SUPPORT_SPL |
| help |
| Support for Freescale LS2081ARDB platform. |
| The LS2081A Reference design board (RDB) is a high-performance |
| development platform that supports the QorIQ LS2081A/LS2041A |
| Layerscape Architecture processor. |
| |
| config TARGET_LX2160ARDB |
| bool "Support lx2160ardb" |
| select ARCH_LX2160A |
| select ARM64 |
| select ARMV8_MULTIENTRY |
| select ARCH_SUPPORT_TFABOOT |
| select BOARD_LATE_INIT |
| help |
| Support for NXP LX2160ARDB platform. |
| The lx2160ardb (LX2160A Reference design board (RDB) |
| is a high-performance development platform that supports the |
| QorIQ LX2160A/LX2120A/LX2080A Layerscape Architecture processor. |
| |
| config TARGET_LX2160AQDS |
| bool "Support lx2160aqds" |
| select ARCH_LX2160A |
| select ARM64 |
| select ARMV8_MULTIENTRY |
| select ARCH_SUPPORT_TFABOOT |
| select BOARD_LATE_INIT |
| help |
| Support for NXP LX2160AQDS platform. |
| The lx2160aqds (LX2160A QorIQ Development System (QDS) |
| is a high-performance development platform that supports the |
| QorIQ LX2160A/LX2120A/LX2080A Layerscape Architecture processor. |
| |
| config TARGET_HIKEY |
| bool "Support HiKey 96boards Consumer Edition Platform" |
| select ARM64 |
| select DM |
| select DM_GPIO |
| select DM_SERIAL |
| select OF_CONTROL |
| select PL01X_SERIAL |
| select SPECIFY_CONSOLE_INDEX |
| imply CMD_DM |
| help |
| Support for HiKey 96boards platform. It features a HI6220 |
| SoC, with 8xA53 CPU, mali450 gpu, and 1GB RAM. |
| |
| config TARGET_HIKEY960 |
| bool "Support HiKey960 96boards Consumer Edition Platform" |
| select ARM64 |
| select DM |
| select DM_SERIAL |
| select OF_CONTROL |
| select PL01X_SERIAL |
| imply CMD_DM |
| help |
| Support for HiKey960 96boards platform. It features a HI3660 |
| SoC, with 4xA73 CPU, 4xA53 CPU, MALI-G71 GPU, and 3GB RAM. |
| |
| config TARGET_POPLAR |
| bool "Support Poplar 96boards Enterprise Edition Platform" |
| select ARM64 |
| select DM |
| select DM_SERIAL |
| select DM_USB |
| select OF_CONTROL |
| select PL01X_SERIAL |
| imply CMD_DM |
| help |
| Support for Poplar 96boards EE platform. It features a HI3798cv200 |
| SoC, with 4xA53 CPU, 1GB RAM and the high performance Mali T720 GPU |
| making it capable of running any commercial set-top solution based on |
| Linux or Android. |
| |
| config TARGET_LS1012AQDS |
| bool "Support ls1012aqds" |
| select ARCH_LS1012A |
| select ARM64 |
| select ARCH_SUPPORT_TFABOOT |
| select BOARD_LATE_INIT |
| help |
| Support for Freescale LS1012AQDS platform. |
| The LS1012A Development System (QDS) is a high-performance |
| development platform that supports the QorIQ LS1012A |
| Layerscape Architecture processor. |
| |
| config TARGET_LS1012ARDB |
| bool "Support ls1012ardb" |
| select ARCH_LS1012A |
| select ARM64 |
| select ARCH_SUPPORT_TFABOOT |
| select BOARD_LATE_INIT |
| imply SCSI |
| imply SCSI_AHCI |
| help |
| Support for Freescale LS1012ARDB platform. |
| The LS1012A Reference design board (RDB) is a high-performance |
| development platform that supports the QorIQ LS1012A |
| Layerscape Architecture processor. |
| |
| config TARGET_LS1012A2G5RDB |
| bool "Support ls1012a2g5rdb" |
| select ARCH_LS1012A |
| select ARM64 |
| select ARCH_SUPPORT_TFABOOT |
| select BOARD_LATE_INIT |
| imply SCSI |
| help |
| Support for Freescale LS1012A2G5RDB platform. |
| The LS1012A 2G5 Reference design board (RDB) is a high-performance |
| development platform that supports the QorIQ LS1012A |
| Layerscape Architecture processor. |
| |
| config TARGET_LS1012AFRWY |
| bool "Support ls1012afrwy" |
| select ARCH_LS1012A |
| select ARM64 |
| select ARCH_SUPPORT_TFABOOT |
| select BOARD_LATE_INIT |
| imply SCSI |
| imply SCSI_AHCI |
| help |
| Support for Freescale LS1012AFRWY platform. |
| The LS1012A FRWY board (FRWY) is a high-performance |
| development platform that supports the QorIQ LS1012A |
| Layerscape Architecture processor. |
| |
| config TARGET_LS1012AFRDM |
| bool "Support ls1012afrdm" |
| select ARCH_LS1012A |
| select ARM64 |
| select ARCH_SUPPORT_TFABOOT |
| help |
| Support for Freescale LS1012AFRDM platform. |
| The LS1012A Freedom board (FRDM) is a high-performance |
| development platform that supports the QorIQ LS1012A |
| Layerscape Architecture processor. |
| |
| config TARGET_LS1028AQDS |
| bool "Support ls1028aqds" |
| select ARCH_LS1028A |
| select ARM64 |
| select ARMV8_MULTIENTRY |
| select ARCH_SUPPORT_TFABOOT |
| select BOARD_LATE_INIT |
| help |
| Support for Freescale LS1028AQDS platform |
| The LS1028A Development System (QDS) is a high-performance |
| development platform that supports the QorIQ LS1028A |
| Layerscape Architecture processor. |
| |
| config TARGET_LS1028ARDB |
| bool "Support ls1028ardb" |
| select ARCH_LS1028A |
| select ARM64 |
| select ARMV8_MULTIENTRY |
| select ARCH_SUPPORT_TFABOOT |
| select BOARD_LATE_INIT |
| help |
| Support for Freescale LS1028ARDB platform |
| The LS1028A Development System (RDB) is a high-performance |
| development platform that supports the QorIQ LS1028A |
| Layerscape Architecture processor. |
| |
| config TARGET_LS1088ARDB |
| bool "Support ls1088ardb" |
| select ARCH_LS1088A |
| select ARM64 |
| select ARMV8_MULTIENTRY |
| select ARCH_SUPPORT_TFABOOT |
| select BOARD_LATE_INIT |
| select SUPPORT_SPL |
| select FSL_DDR_INTERACTIVE if !SD_BOOT |
| help |
| Support for NXP LS1088ARDB platform. |
| The LS1088A Reference design board (RDB) is a high-performance |
| development platform that supports the QorIQ LS1088A |
| Layerscape Architecture processor. |
| |
| config TARGET_LS1021AQDS |
| bool "Support ls1021aqds" |
| select ARCH_LS1021A |
| select ARCH_SUPPORT_PSCI |
| select BOARD_EARLY_INIT_F |
| select BOARD_LATE_INIT |
| select CPU_V7A |
| select CPU_V7_HAS_NONSEC |
| select CPU_V7_HAS_VIRT |
| select LS1_DEEP_SLEEP |
| select SUPPORT_SPL |
| select SYS_FSL_DDR |
| select FSL_DDR_INTERACTIVE |
| select DM_SPI_FLASH if FSL_DSPI || FSL_QSPI |
| select SPI_FLASH_DATAFLASH if FSL_DSPI || FSL_QSPI |
| imply SCSI |
| |
| config TARGET_LS1021ATWR |
| bool "Support ls1021atwr" |
| select ARCH_LS1021A |
| select ARCH_SUPPORT_PSCI |
| select BOARD_EARLY_INIT_F |
| select BOARD_LATE_INIT |
| select CPU_V7A |
| select CPU_V7_HAS_NONSEC |
| select CPU_V7_HAS_VIRT |
| select LS1_DEEP_SLEEP |
| select SUPPORT_SPL |
| select DM_SPI_FLASH if FSL_DSPI || FSL_QSPI |
| imply SCSI |
| |
| config TARGET_LS1021ATSN |
| bool "Support ls1021atsn" |
| select ARCH_LS1021A |
| select ARCH_SUPPORT_PSCI |
| select BOARD_EARLY_INIT_F |
| select BOARD_LATE_INIT |
| select CPU_V7A |
| select CPU_V7_HAS_NONSEC |
| select CPU_V7_HAS_VIRT |
| select LS1_DEEP_SLEEP |
| select SUPPORT_SPL |
| imply SCSI |
| |
| config TARGET_LS1021AIOT |
| bool "Support ls1021aiot" |
| select ARCH_LS1021A |
| select ARCH_SUPPORT_PSCI |
| select BOARD_LATE_INIT |
| select CPU_V7A |
| select CPU_V7_HAS_NONSEC |
| select CPU_V7_HAS_VIRT |
| select SUPPORT_SPL |
| select DM_SPI_FLASH if FSL_DSPI || FSL_QSPI |
| imply SCSI |
| help |
| Support for Freescale LS1021AIOT platform. |
| The LS1021A Freescale board (IOT) is a high-performance |
| development platform that supports the QorIQ LS1021A |
| Layerscape Architecture processor. |
| |
| config TARGET_LS1043AQDS |
| bool "Support ls1043aqds" |
| select ARCH_LS1043A |
| select ARM64 |
| select ARMV8_MULTIENTRY |
| select ARCH_SUPPORT_TFABOOT |
| select BOARD_EARLY_INIT_F |
| select BOARD_LATE_INIT |
| select SUPPORT_SPL |
| select FSL_DDR_INTERACTIVE if !SPL |
| select FSL_DSPI if !SPL_NO_DSPI |
| select DM_SPI_FLASH if FSL_DSPI |
| imply SCSI |
| imply SCSI_AHCI |
| help |
| Support for Freescale LS1043AQDS platform. |
| |
| config TARGET_LS1043ARDB |
| bool "Support ls1043ardb" |
| select ARCH_LS1043A |
| select ARM64 |
| select ARMV8_MULTIENTRY |
| select ARCH_SUPPORT_TFABOOT |
| select BOARD_EARLY_INIT_F |
| select BOARD_LATE_INIT |
| select SUPPORT_SPL |
| select FSL_DSPI if !SPL_NO_DSPI |
| select DM_SPI_FLASH if FSL_DSPI |
| help |
| Support for Freescale LS1043ARDB platform. |
| |
| config TARGET_LS1046AQDS |
| bool "Support ls1046aqds" |
| select ARCH_LS1046A |
| select ARM64 |
| select ARMV8_MULTIENTRY |
| select ARCH_SUPPORT_TFABOOT |
| select BOARD_EARLY_INIT_F |
| select BOARD_LATE_INIT |
| select DM_SPI_FLASH if DM_SPI |
| select SUPPORT_SPL |
| select FSL_DDR_BIST if !SPL |
| select FSL_DDR_INTERACTIVE if !SPL |
| select FSL_DDR_INTERACTIVE if !SPL |
| imply SCSI |
| help |
| Support for Freescale LS1046AQDS platform. |
| The LS1046A Development System (QDS) is a high-performance |
| development platform that supports the QorIQ LS1046A |
| Layerscape Architecture processor. |
| |
| config TARGET_LS1046ARDB |
| bool "Support ls1046ardb" |
| select ARCH_LS1046A |
| select ARM64 |
| select ARMV8_MULTIENTRY |
| select ARCH_SUPPORT_TFABOOT |
| select BOARD_EARLY_INIT_F |
| select BOARD_LATE_INIT |
| select DM_SPI_FLASH if DM_SPI |
| select POWER_MC34VR500 |
| select SUPPORT_SPL |
| select FSL_DDR_BIST |
| select FSL_DDR_INTERACTIVE if !SPL |
| imply SCSI |
| help |
| Support for Freescale LS1046ARDB platform. |
| The LS1046A Reference Design Board (RDB) is a high-performance |
| development platform that supports the QorIQ LS1046A |
| Layerscape Architecture processor. |
| |
| config TARGET_LS1046AFRWY |
| bool "Support ls1046afrwy" |
| select ARCH_LS1046A |
| select ARM64 |
| select ARMV8_MULTIENTRY |
| select ARCH_SUPPORT_TFABOOT |
| select BOARD_EARLY_INIT_F |
| select BOARD_LATE_INIT |
| select DM_SPI_FLASH if DM_SPI |
| imply SCSI |
| help |
| Support for Freescale LS1046AFRWY platform. |
| The LS1046A Freeway Board (FRWY) is a high-performance |
| development platform that supports the QorIQ LS1046A |
| Layerscape Architecture processor. |
| |
| config TARGET_COLIBRI_PXA270 |
| bool "Support colibri_pxa270" |
| select CPU_PXA |
| |
| config ARCH_UNIPHIER |
| bool "Socionext UniPhier SoCs" |
| select BOARD_LATE_INIT |
| select DM |
| select DM_ETH |
| select DM_GPIO |
| select DM_I2C |
| select DM_MMC |
| select DM_MTD |
| select DM_RESET |
| select DM_SERIAL |
| select DM_USB |
| select OF_BOARD_SETUP |
| select OF_CONTROL |
| select OF_LIBFDT |
| select PINCTRL |
| select SPL_BOARD_INIT if SPL |
| select SPL_DM if SPL |
| select SPL_LIBCOMMON_SUPPORT if SPL |
| select SPL_LIBGENERIC_SUPPORT if SPL |
| select SPL_OF_CONTROL if SPL |
| select SPL_PINCTRL if SPL |
| select SUPPORT_SPL |
| imply CMD_DM |
| imply DISTRO_DEFAULTS |
| imply FAT_WRITE |
| help |
| Support for UniPhier SoC family developed by Socionext Inc. |
| (formerly, System LSI Business Division of Panasonic Corporation) |
| |
| config ARCH_STM32 |
| bool "Support STMicroelectronics STM32 MCU with cortex M" |
| select CPU_V7M |
| select DM |
| select DM_SERIAL |
| imply CMD_DM |
| |
| config ARCH_STI |
| bool "Support STMicrolectronics SoCs" |
| select BLK |
| select CPU_V7A |
| select DM |
| select DM_MMC |
| select DM_RESET |
| select DM_SERIAL |
| imply CMD_DM |
| help |
| Support for STMicroelectronics STiH407/10 SoC family. |
| This SoC is used on Linaro 96Board STiH410-B2260 |
| |
| config ARCH_STM32MP |
| bool "Support STMicroelectronics STM32MP Socs with cortex A" |
| select ARCH_MISC_INIT |
| select ARCH_SUPPORT_TFABOOT |
| select BOARD_LATE_INIT |
| select CLK |
| select DM |
| select DM_GPIO |
| select DM_RESET |
| select DM_SERIAL |
| select MISC |
| select OF_CONTROL |
| select OF_LIBFDT |
| select OF_SYSTEM_SETUP |
| select PINCTRL |
| select REGMAP |
| select SUPPORT_SPL |
| select SYSCON |
| select SYSRESET |
| select SYS_THUMB_BUILD |
| imply SPL_SYSRESET |
| imply CMD_DM |
| imply CMD_POWEROFF |
| imply OF_LIBFDT_OVERLAY |
| imply ENV_VARS_UBOOT_RUNTIME_CONFIG |
| imply USE_PREBOOT |
| help |
| Support for STM32MP SoC family developed by STMicroelectronics, |
| MPUs based on ARM cortex A core |
| U-BOOT is running in DDR, loaded by the First Stage BootLoader (FSBL). |
| FSBL can be TF-A: Trusted Firmware for Cortex A, for trusted boot |
| chain. |
| SPL is the unsecure FSBL for the basic boot chain. |
| |
| config ARCH_ROCKCHIP |
| bool "Support Rockchip SoCs" |
| select BLK |
| select BINMAN if !ARM64 |
| select DM |
| select DM_GPIO |
| select DM_I2C |
| select DM_MMC |
| select DM_PWM |
| select DM_REGULATOR |
| select DM_SERIAL |
| select DM_SPI |
| select DM_SPI_FLASH |
| select DM_USB if USB |
| select ENABLE_ARM_SOC_BOOT0_HOOK |
| select OF_CONTROL |
| select SPI |
| select SPL_DM if SPL |
| select SPL_DM_SPI if SPL |
| select SPL_DM_SPI_FLASH if SPL |
| select SYS_MALLOC_F |
| select SYS_THUMB_BUILD if !ARM64 |
| imply ADC |
| imply CMD_DM |
| imply DEBUG_UART_BOARD_INIT |
| imply DISTRO_DEFAULTS |
| imply FAT_WRITE |
| imply SARADC_ROCKCHIP |
| imply SPL_SYSRESET |
| imply SPL_SYS_MALLOC_SIMPLE |
| imply SYS_NS16550 |
| imply TPL_SYSRESET |
| imply USB_FUNCTION_FASTBOOT |
| |
| config ARCH_OCTEONTX |
| bool "Support OcteonTX SoCs" |
| select DM |
| select ARM64 |
| select OF_CONTROL |
| select OF_LIVE |
| select BOARD_LATE_INIT |
| select SYS_CACHE_SHIFT_7 |
| |
| config ARCH_OCTEONTX2 |
| bool "Support OcteonTX2 SoCs" |
| select DM |
| select ARM64 |
| select OF_CONTROL |
| select OF_LIVE |
| select BOARD_LATE_INIT |
| select SYS_CACHE_SHIFT_7 |
| |
| config TARGET_THUNDERX_88XX |
| bool "Support ThunderX 88xx" |
| select ARM64 |
| select OF_CONTROL |
| select PL01X_SERIAL |
| select SYS_CACHE_SHIFT_7 |
| |
| config ARCH_ASPEED |
| bool "Support Aspeed SoCs" |
| select DM |
| select OF_CONTROL |
| imply CMD_DM |
| |
| config TARGET_DURIAN |
| bool "Support Phytium Durian Platform" |
| select ARM64 |
| help |
| Support for durian platform. |
| It has 2GB Sdram, uart and pcie. |
| |
| config TARGET_PRESIDIO_ASIC |
| bool "Support Cortina Presidio ASIC Platform" |
| select ARM64 |
| |
| config TARGET_XENGUEST_ARM64 |
| bool "Xen guest ARM64" |
| select ARM64 |
| select XEN |
| select OF_CONTROL |
| select LINUX_KERNEL_IMAGE_HEADER |
| select XEN_SERIAL |
| select SSCANF |
| endchoice |
| |
| config ARCH_SUPPORT_TFABOOT |
| bool |
| |
| config TFABOOT |
| bool "Support for booting from TF-A" |
| depends on ARCH_SUPPORT_TFABOOT |
| default n |
| help |
| Enabling this will make a U-Boot binary that is capable of being |
| booted via TF-A (Trusted Firmware for Cortex-A). |
| |
| config TI_SECURE_DEVICE |
| bool "HS Device Type Support" |
| depends on ARCH_KEYSTONE || ARCH_OMAP2PLUS || ARCH_K3 |
| help |
| If a high secure (HS) device type is being used, this config |
| must be set. This option impacts various aspects of the |
| build system (to create signed boot images that can be |
| authenticated) and the code. See the doc/README.ti-secure |
| file for further details. |
| |
| if AM43XX || AM33XX || OMAP54XX || ARCH_KEYSTONE |
| config ISW_ENTRY_ADDR |
| hex "Address in memory or XIP address of bootloader entry point" |
| default 0x402F4000 if AM43XX |
| default 0x402F0400 if AM33XX |
| default 0x40301350 if OMAP54XX |
| help |
| After any reset, the boot ROM searches the boot media for a valid |
| boot image. For non-XIP devices, the ROM then copies the image into |
| internal memory. For all boot modes, after the ROM processes the |
| boot image it eventually computes the entry point address depending |
| on the device type (secure/non-secure), boot media (xip/non-xip) and |
| image headers. |
| endif |
| |
| source "arch/arm/mach-aspeed/Kconfig" |
| |
| source "arch/arm/mach-at91/Kconfig" |
| |
| source "arch/arm/mach-bcm283x/Kconfig" |
| |
| source "arch/arm/mach-bcmstb/Kconfig" |
| |
| source "arch/arm/mach-davinci/Kconfig" |
| |
| source "arch/arm/mach-exynos/Kconfig" |
| |
| source "arch/arm/mach-highbank/Kconfig" |
| |
| source "arch/arm/mach-integrator/Kconfig" |
| |
| source "arch/arm/mach-ipq40xx/Kconfig" |
| |
| source "arch/arm/mach-k3/Kconfig" |
| |
| source "arch/arm/mach-keystone/Kconfig" |
| |
| source "arch/arm/mach-kirkwood/Kconfig" |
| |
| source "arch/arm/mach-lpc32xx/Kconfig" |
| |
| source "arch/arm/mach-mvebu/Kconfig" |
| |
| source "arch/arm/mach-octeontx/Kconfig" |
| |
| source "arch/arm/mach-octeontx2/Kconfig" |
| |
| source "arch/arm/cpu/armv7/ls102xa/Kconfig" |
| |
| source "arch/arm/mach-imx/mx2/Kconfig" |
| |
| source "arch/arm/mach-imx/mx3/Kconfig" |
| |
| source "arch/arm/mach-imx/mx5/Kconfig" |
| |
| source "arch/arm/mach-imx/mx6/Kconfig" |
| |
| source "arch/arm/mach-imx/mx7/Kconfig" |
| |
| source "arch/arm/mach-imx/mx7ulp/Kconfig" |
| |
| source "arch/arm/mach-imx/imx8/Kconfig" |
| |
| source "arch/arm/mach-imx/imx8m/Kconfig" |
| |
| source "arch/arm/mach-imx/imxrt/Kconfig" |
| |
| source "arch/arm/mach-imx/mxs/Kconfig" |
| |
| source "arch/arm/mach-omap2/Kconfig" |
| |
| source "arch/arm/cpu/armv8/fsl-layerscape/Kconfig" |
| |
| source "arch/arm/mach-orion5x/Kconfig" |
| |
| source "arch/arm/mach-owl/Kconfig" |
| |
| source "arch/arm/mach-rmobile/Kconfig" |
| |
| source "arch/arm/mach-meson/Kconfig" |
| |
| source "arch/arm/mach-mediatek/Kconfig" |
| |
| source "arch/arm/mach-qemu/Kconfig" |
| |
| source "arch/arm/mach-rockchip/Kconfig" |
| |
| source "arch/arm/mach-s5pc1xx/Kconfig" |
| |
| source "arch/arm/mach-snapdragon/Kconfig" |
| |
| source "arch/arm/mach-socfpga/Kconfig" |
| |
| source "arch/arm/mach-sti/Kconfig" |
| |
| source "arch/arm/mach-stm32/Kconfig" |
| |
| source "arch/arm/mach-stm32mp/Kconfig" |
| |
| source "arch/arm/mach-sunxi/Kconfig" |
| |
| source "arch/arm/mach-tegra/Kconfig" |
| |
| source "arch/arm/mach-u8500/Kconfig" |
| |
| source "arch/arm/mach-uniphier/Kconfig" |
| |
| source "arch/arm/cpu/armv7/vf610/Kconfig" |
| |
| source "arch/arm/mach-zynq/Kconfig" |
| |
| source "arch/arm/mach-zynqmp/Kconfig" |
| |
| source "arch/arm/mach-versal/Kconfig" |
| |
| source "arch/arm/mach-zynqmp-r5/Kconfig" |
| |
| source "arch/arm/cpu/armv7/Kconfig" |
| |
| source "arch/arm/cpu/armv8/Kconfig" |
| |
| source "arch/arm/mach-imx/Kconfig" |
| |
| source "arch/arm/mach-nexell/Kconfig" |
| |
| source "board/armltd/total_compute/Kconfig" |
| |
| source "board/bosch/shc/Kconfig" |
| source "board/bosch/guardian/Kconfig" |
| source "board/CarMediaLab/flea3/Kconfig" |
| source "board/Marvell/aspenite/Kconfig" |
| source "board/Marvell/gplugd/Kconfig" |
| source "board/Marvell/octeontx/Kconfig" |
| source "board/Marvell/octeontx2/Kconfig" |
| source "board/armadeus/apf27/Kconfig" |
| source "board/armltd/vexpress/Kconfig" |
| source "board/armltd/vexpress64/Kconfig" |
| source "board/cortina/presidio-asic/Kconfig" |
| source "board/broadcom/bcm23550_w1d/Kconfig" |
| source "board/broadcom/bcm28155_ap/Kconfig" |
| source "board/broadcom/bcm963158/Kconfig" |
| source "board/broadcom/bcm968360bg/Kconfig" |
| source "board/broadcom/bcm968580xref/Kconfig" |
| source "board/broadcom/bcmcygnus/Kconfig" |
| source "board/broadcom/bcmnsp/Kconfig" |
| source "board/broadcom/bcmns2/Kconfig" |
| source "board/broadcom/bcmns3/Kconfig" |
| source "board/cavium/thunderx/Kconfig" |
| source "board/cirrus/edb93xx/Kconfig" |
| source "board/eets/pdu001/Kconfig" |
| source "board/emulation/qemu-arm/Kconfig" |
| source "board/freescale/ls2080a/Kconfig" |
| source "board/freescale/ls2080aqds/Kconfig" |
| source "board/freescale/ls2080ardb/Kconfig" |
| source "board/freescale/ls1088a/Kconfig" |
| source "board/freescale/ls1028a/Kconfig" |
| source "board/freescale/ls1021aqds/Kconfig" |
| source "board/freescale/ls1043aqds/Kconfig" |
| source "board/freescale/ls1021atwr/Kconfig" |
| source "board/freescale/ls1021atsn/Kconfig" |
| source "board/freescale/ls1021aiot/Kconfig" |
| source "board/freescale/ls1046aqds/Kconfig" |
| source "board/freescale/ls1043ardb/Kconfig" |
| source "board/freescale/ls1046ardb/Kconfig" |
| source "board/freescale/ls1046afrwy/Kconfig" |
| source "board/freescale/ls1012aqds/Kconfig" |
| source "board/freescale/ls1012ardb/Kconfig" |
| source "board/freescale/ls1012afrdm/Kconfig" |
| source "board/freescale/lx2160a/Kconfig" |
| source "board/freescale/mx35pdk/Kconfig" |
| source "board/freescale/s32v234evb/Kconfig" |
| source "board/grinn/chiliboard/Kconfig" |
| source "board/hisilicon/hikey/Kconfig" |
| source "board/hisilicon/hikey960/Kconfig" |
| source "board/hisilicon/poplar/Kconfig" |
| source "board/isee/igep003x/Kconfig" |
| source "board/myir/mys_6ulx/Kconfig" |
| source "board/spear/spear300/Kconfig" |
| source "board/spear/spear310/Kconfig" |
| source "board/spear/spear320/Kconfig" |
| source "board/spear/spear600/Kconfig" |
| source "board/spear/x600/Kconfig" |
| source "board/st/stv0991/Kconfig" |
| source "board/tcl/sl50/Kconfig" |
| source "board/toradex/colibri_pxa270/Kconfig" |
| source "board/variscite/dart_6ul/Kconfig" |
| source "board/vscom/baltos/Kconfig" |
| source "board/phytium/durian/Kconfig" |
| source "board/xen/xenguest_arm64/Kconfig" |
| |
| source "arch/arm/Kconfig.debug" |
| |
| endmenu |
| |
| config SPL_LDSCRIPT |
| default "arch/arm/cpu/arm926ejs/mxs/u-boot-spl.lds" if (ARCH_MX23 || ARCH_MX28) && !SPL_FRAMEWORK |
| default "arch/arm/cpu/arm1136/u-boot-spl.lds" if CPU_ARM1136 |
| default "arch/arm/cpu/armv8/u-boot-spl.lds" if ARM64 |