| .. SPDX-License-Identifier: GPL-2.0+ |
| |
| U-Boot for JetHub J100 |
| ======================= |
| |
| JetHome Jethub D1 (http://jethome.ru/jethub-d1) is a home automation |
| controller manufactured by JetHome with the following specifications: |
| |
| - Amlogic A113X (ARM Cortex-A53) quad-core up to 1.5GHz |
| - no video out |
| - 512Mb/1GB DDR3 |
| - 8/16GB eMMC flash |
| - 1 x USB 2.0 |
| - 1 x 10/100Mbps ethernet |
| - WiFi / Bluetooth AMPAK AP6255 (Broadcom BCM43455) IEEE |
| 802.11a/b/g/n/ac, Bluetooth 4.2. |
| - TI CC2538 + CC2592 Zigbee Wireless Module with up to 20dBm output |
| power and Zigbee 3.0 support. |
| - 2 x gpio LEDS |
| - GPIO user Button |
| - 1 x 1-Wire |
| - 2 x RS-485 |
| - 4 x dry contact digital GPIO inputs |
| - 3 x relay GPIO outputs |
| - DC source with a voltage of 9 to 56 V / Passive POE |
| - DIN Rail Mounting case |
| |
| U-Boot compilation |
| ------------------ |
| |
| .. code-block:: bash |
| |
| $ export CROSS_COMPILE=aarch64-none-elf- |
| $ make jethub_j100_defconfig |
| $ make |
| |
| Image creation |
| -------------- |
| |
| For simplified usage, pleaser refer to :doc:`pre-generated-fip` with codename `jethub-j100` |
| |
| Amlogic doesn't provide sources for the firmware and for tools needed |
| to create the bootloader image, so it is necessary to obtain binaries |
| from the git tree published by the board vendor: |
| |
| .. code-block:: bash |
| |
| $ git clone https://github.com/jethome-ru/jethub-aml-tools jethub-u-boot |
| $ cd jethub-u-boot |
| $ export FIPDIR=$PWD |
| |
| Go back to mainline U-boot source tree then : |
| |
| .. code-block:: bash |
| |
| $ mkdir fip |
| |
| $ cp $FIPDIR/j100/bl2.bin fip/ |
| $ cp $FIPDIR/j100/acs.bin fip/ |
| $ cp $FIPDIR/j100/bl21.bin fip/ |
| $ cp $FIPDIR/j100/bl30.bin fip/ |
| $ cp $FIPDIR/j100/bl301.bin fip/ |
| $ cp $FIPDIR/j100/bl31.img fip/ |
| $ cp u-boot.bin fip/bl33.bin |
| |
| $ $FIPDIR/blx_fix.sh \ |
| fip/bl30.bin \ |
| fip/zero_tmp \ |
| fip/bl30_zero.bin \ |
| fip/bl301.bin \ |
| fip/bl301_zero.bin \ |
| fip/bl30_new.bin \ |
| bl30 |
| |
| $ $FIPDIR/acs_tool.pyc fip/bl2.bin fip/bl2_acs.bin fip/acs.bin 0 |
| |
| $ $FIPDIR/blx_fix.sh \ |
| fip/bl2_acs.bin \ |
| fip/zero_tmp \ |
| fip/bl2_zero.bin \ |
| fip/bl21.bin \ |
| fip/bl21_zero.bin \ |
| fip/bl2_new.bin \ |
| bl2 |
| |
| $ $FIPDIR/j100/aml_encrypt_axg --bl3sig --input fip/bl30_new.bin \ |
| --output fip/bl30_new.bin.enc \ |
| --level v3 --type bl30 |
| $ $FIPDIR/j100/aml_encrypt_axg --bl3sig --input fip/bl31.img \ |
| --output fip/bl31.img.enc \ |
| --level v3 --type bl31 |
| $ $FIPDIR/j100/aml_encrypt_axg --bl3sig --input fip/bl33.bin --compress lz4 \ |
| --output fip/bl33.bin.enc \ |
| --level v3 --type bl33 |
| $ $FIPDIR/j100/aml_encrypt_axg --bl2sig --input fip/bl2_new.bin \ |
| --output fip/bl2.n.bin.sig |
| $ $FIPDIR/j100/aml_encrypt_axg --bootmk \ |
| --output fip/u-boot.bin \ |
| --bl2 fip/bl2.n.bin.sig \ |
| --bl30 fip/bl30_new.bin.enc \ |
| --bl31 fip/bl31.img.enc \ |
| --bl33 fip/bl33.bin.enc --level v3 |
| |
| and then write the image to eMMC with: |
| |
| .. code-block:: bash |
| |
| $ DEV=/dev/your_emmc_device |
| $ dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=512 skip=1 seek=1 |
| $ dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=1 count=444 |