| // SPDX-License-Identifier: GPL-2.0-or-later |
| /* |
| * Copyright 2022 Toradex |
| */ |
| |
| #include <common.h> |
| #include <asm/arch/clock.h> |
| #include <asm/arch/imx8mp_pins.h> |
| #include <asm/arch/sys_proto.h> |
| #include <asm-generic/gpio.h> |
| #include <asm/global_data.h> |
| #include <asm/mach-imx/gpio.h> |
| #include <asm/mach-imx/iomux-v3.h> |
| #include <errno.h> |
| #include <env.h> |
| #include <init.h> |
| #include <linux/delay.h> |
| #include <micrel.h> |
| #include <miiphy.h> |
| #include <netdev.h> |
| |
| #include "../common/tdx-cfg-block.h" |
| |
| DECLARE_GLOBAL_DATA_PTR; |
| |
| #define UART_PAD_CTRL (PAD_CTL_DSE6 | PAD_CTL_FSEL1) |
| #define WDOG_PAD_CTRL (PAD_CTL_DSE6 | PAD_CTL_ODE | PAD_CTL_PUE | PAD_CTL_PE) |
| |
| /* Verdin UART_3, Console/Debug UART */ |
| static const iomux_v3_cfg_t uart_pads[] = { |
| MX8MP_PAD_UART3_RXD__UART3_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL), |
| MX8MP_PAD_UART3_TXD__UART3_DCE_TX | MUX_PAD_CTRL(UART_PAD_CTRL), |
| }; |
| |
| static const iomux_v3_cfg_t wdog_pads[] = { |
| MX8MP_PAD_GPIO1_IO02__WDOG1_WDOG_B | MUX_PAD_CTRL(WDOG_PAD_CTRL), |
| }; |
| |
| int board_early_init_f(void) |
| { |
| struct wdog_regs *wdog = (struct wdog_regs *)WDOG1_BASE_ADDR; |
| |
| imx_iomux_v3_setup_multiple_pads(wdog_pads, ARRAY_SIZE(wdog_pads)); |
| |
| set_wdog_reset(wdog); |
| |
| imx_iomux_v3_setup_multiple_pads(uart_pads, ARRAY_SIZE(uart_pads)); |
| |
| init_uart_clk(2); |
| |
| return 0; |
| } |
| |
| static void setup_fec(void) |
| { |
| struct iomuxc_gpr_base_regs *gpr = |
| (struct iomuxc_gpr_base_regs *)IOMUXC_GPR_BASE_ADDR; |
| |
| /* Enable RGMII TX clk output */ |
| setbits_le32(&gpr->gpr[1], BIT(22)); |
| } |
| |
| static int setup_eqos(void) |
| { |
| struct iomuxc_gpr_base_regs *gpr = |
| (struct iomuxc_gpr_base_regs *)IOMUXC_GPR_BASE_ADDR; |
| |
| /* set INTF as RGMII, enable RGMII TXC clock */ |
| clrsetbits_le32(&gpr->gpr[1], |
| IOMUXC_GPR_GPR1_GPR_ENET_QOS_INTF_SEL_MASK, BIT(16)); |
| setbits_le32(&gpr->gpr[1], BIT(19) | BIT(21)); |
| |
| return set_clk_eqos(ENET_125MHZ); |
| } |
| |
| #if IS_ENABLED(CONFIG_NET) |
| int board_phy_config(struct phy_device *phydev) |
| { |
| if (phydev->drv->config) |
| phydev->drv->config(phydev); |
| return 0; |
| } |
| #endif |
| |
| int board_init(void) |
| { |
| int ret = 0; |
| |
| if (IS_ENABLED(CONFIG_FEC_MXC)) |
| setup_fec(); |
| |
| if (IS_ENABLED(CONFIG_DWC_ETH_QOS)) |
| ret = setup_eqos(); |
| |
| return ret; |
| } |
| |
| static void select_dt_from_module_version(void) |
| { |
| char variant[32]; |
| char *env_variant = env_get("variant"); |
| int is_wifi = 0; |
| |
| if (IS_ENABLED(CONFIG_TDX_CFG_BLOCK)) { |
| /* |
| * If we have a valid config block and it says we are a module with |
| * Wi-Fi/Bluetooth make sure we use the -wifi device tree. |
| */ |
| is_wifi = (tdx_hw_tag.prodid == VERDIN_IMX8MPQ_WIFI_BT_IT) || |
| (tdx_hw_tag.prodid == VERDIN_IMX8MPQ_2GB_WIFI_BT_IT) || |
| (tdx_hw_tag.prodid == VERDIN_IMX8MPQ_8GB_WIFI_BT); |
| } |
| |
| if (is_wifi) |
| strlcpy(&variant[0], "wifi", sizeof(variant)); |
| else |
| strlcpy(&variant[0], "nonwifi", sizeof(variant)); |
| |
| if (strcmp(variant, env_variant)) { |
| printf("Setting variant to %s\n", variant); |
| env_set("variant", variant); |
| |
| if (IS_ENABLED(CONFIG_ENV_IS_NOWHERE)) |
| env_save(); |
| } |
| } |
| |
| int board_late_init(void) |
| { |
| select_dt_from_module_version(); |
| |
| return 0; |
| } |
| |
| #if IS_ENABLED(CONFIG_OF_LIBFDT) && IS_ENABLED(CONFIG_OF_BOARD_SETUP) |
| int ft_board_setup(void *blob, struct bd_info *bd) |
| { |
| return 0; |
| } |
| #endif |