| // SPDX-License-Identifier: GPL-2.0+ |
| /* |
| * Copyright (C) 2018 Marek Vasut <marek.vasut@gmail.com> |
| */ |
| |
| #include <common.h> |
| #include <bouncebuf.h> |
| #include <clk.h> |
| #include <fdtdec.h> |
| #include <log.h> |
| #include <malloc.h> |
| #include <mmc.h> |
| #include <dm.h> |
| #include <asm/global_data.h> |
| #include <dm/device_compat.h> |
| #include <linux/bitops.h> |
| #include <linux/compat.h> |
| #include <linux/delay.h> |
| #include <linux/dma-direction.h> |
| #include <linux/io.h> |
| #include <linux/sizes.h> |
| #include <power/regulator.h> |
| #include <reset.h> |
| #include <asm/unaligned.h> |
| #include "tmio-common.h" |
| |
| #if CONFIG_IS_ENABLED(MMC_UHS_SUPPORT) || \ |
| CONFIG_IS_ENABLED(MMC_HS200_SUPPORT) || \ |
| CONFIG_IS_ENABLED(MMC_HS400_SUPPORT) |
| |
| /* SCC registers */ |
| #define RENESAS_SDHI_SCC_DTCNTL 0x800 |
| #define RENESAS_SDHI_SCC_DTCNTL_TAPEN BIT(0) |
| #define RENESAS_SDHI_SCC_DTCNTL_TAPNUM_SHIFT 16 |
| #define RENESAS_SDHI_SCC_DTCNTL_TAPNUM_MASK 0xff |
| #define RENESAS_SDHI_SCC_TAPSET 0x804 |
| #define RENESAS_SDHI_SCC_DT2FF 0x808 |
| #define RENESAS_SDHI_SCC_CKSEL 0x80c |
| #define RENESAS_SDHI_SCC_CKSEL_DTSEL BIT(0) |
| #define RENESAS_SDHI_SCC_RVSCNTL 0x810 |
| #define RENESAS_SDHI_SCC_RVSCNTL_RVSEN BIT(0) |
| #define RENESAS_SDHI_SCC_RVSREQ 0x814 |
| #define RENESAS_SDHI_SCC_RVSREQ_RVSERR BIT(2) |
| #define RENESAS_SDHI_SCC_RVSREQ_REQTAPUP BIT(1) |
| #define RENESAS_SDHI_SCC_RVSREQ_REQTAPDOWN BIT(0) |
| #define RENESAS_SDHI_SCC_SMPCMP 0x818 |
| #define RENESAS_SDHI_SCC_SMPCMP_CMD_ERR (BIT(24) | BIT(8)) |
| #define RENESAS_SDHI_SCC_SMPCMP_CMD_REQUP BIT(24) |
| #define RENESAS_SDHI_SCC_SMPCMP_CMD_REQDOWN BIT(8) |
| #define RENESAS_SDHI_SCC_TMPPORT2 0x81c |
| #define RENESAS_SDHI_SCC_TMPPORT2_HS400EN BIT(31) |
| #define RENESAS_SDHI_SCC_TMPPORT2_HS400OSEL BIT(4) |
| #define RENESAS_SDHI_SCC_TMPPORT3 0x828 |
| #define RENESAS_SDHI_SCC_TMPPORT3_OFFSET_0 3 |
| #define RENESAS_SDHI_SCC_TMPPORT3_OFFSET_1 2 |
| #define RENESAS_SDHI_SCC_TMPPORT3_OFFSET_2 1 |
| #define RENESAS_SDHI_SCC_TMPPORT3_OFFSET_3 0 |
| #define RENESAS_SDHI_SCC_TMPPORT3_OFFSET_MASK 0x3 |
| #define RENESAS_SDHI_SCC_TMPPORT4 0x82c |
| #define RENESAS_SDHI_SCC_TMPPORT4_DLL_ACC_START BIT(0) |
| #define RENESAS_SDHI_SCC_TMPPORT5 0x830 |
| #define RENESAS_SDHI_SCC_TMPPORT5_DLL_RW_SEL_R BIT(8) |
| #define RENESAS_SDHI_SCC_TMPPORT5_DLL_RW_SEL_W (0 << 8) |
| #define RENESAS_SDHI_SCC_TMPPORT5_DLL_ADR_MASK 0x3F |
| #define RENESAS_SDHI_SCC_TMPPORT6 0x834 |
| #define RENESAS_SDHI_SCC_TMPPORT7 0x838 |
| #define RENESAS_SDHI_SCC_TMPPORT_DISABLE_WP_CODE 0xa5000000 |
| #define RENESAS_SDHI_SCC_TMPPORT_CALIB_CODE_MASK 0x1f |
| #define RENESAS_SDHI_SCC_TMPPORT_MANUAL_MODE BIT(7) |
| |
| #define RENESAS_SDHI_MAX_TAP 3 |
| |
| #define CALIB_TABLE_MAX (RENESAS_SDHI_SCC_TMPPORT_CALIB_CODE_MASK + 1) |
| |
| static const u8 r8a7796_rev13_calib_table[2][CALIB_TABLE_MAX] = { |
| { 3, 3, 3, 3, 3, 3, 3, 4, 4, 5, 6, 7, 8, 9, 10, 15, |
| 16, 16, 16, 16, 16, 16, 17, 18, 18, 19, 20, 21, 22, 23, 24, 25 }, |
| { 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 6, 7, 8, 11, |
| 12, 17, 18, 18, 18, 18, 18, 18, 18, 19, 20, 21, 22, 23, 25, 25 } |
| }; |
| |
| static const u8 r8a77965_calib_table[2][CALIB_TABLE_MAX] = { |
| { 1, 2, 6, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 15, 15, 16, |
| 17, 18, 19, 20, 21, 22, 23, 24, 25, 25, 26, 27, 28, 29, 30, 31 }, |
| { 2, 3, 4, 4, 5, 6, 7, 9, 10, 11, 12, 13, 14, 15, 16, 17, |
| 17, 17, 20, 21, 22, 23, 24, 25, 27, 28, 29, 30, 31, 31, 31, 31 } |
| }; |
| |
| static const u8 r8a77990_calib_table[2][CALIB_TABLE_MAX] = { |
| { 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, |
| 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 }, |
| { 0, 0, 0, 1, 2, 3, 3, 4, 4, 4, 5, 5, 6, 8, 9, 10, |
| 11, 12, 13, 15, 16, 17, 17, 18, 18, 19, 20, 22, 24, 25, 26, 26 } |
| }; |
| |
| static int rmobile_is_gen3_mmc0(struct tmio_sd_priv *priv) |
| { |
| /* On R-Car Gen3, MMC0 is at 0xee140000 */ |
| return (uintptr_t)(priv->regbase) == 0xee140000; |
| } |
| |
| static u32 sd_scc_tmpport_read32(struct tmio_sd_priv *priv, u32 addr) |
| { |
| /* read mode */ |
| tmio_sd_writel(priv, RENESAS_SDHI_SCC_TMPPORT5_DLL_RW_SEL_R | |
| (RENESAS_SDHI_SCC_TMPPORT5_DLL_ADR_MASK & addr), |
| RENESAS_SDHI_SCC_TMPPORT5); |
| |
| /* access start and stop */ |
| tmio_sd_writel(priv, RENESAS_SDHI_SCC_TMPPORT4_DLL_ACC_START, |
| RENESAS_SDHI_SCC_TMPPORT4); |
| tmio_sd_writel(priv, 0, RENESAS_SDHI_SCC_TMPPORT4); |
| |
| return tmio_sd_readl(priv, RENESAS_SDHI_SCC_TMPPORT7); |
| } |
| |
| static void sd_scc_tmpport_write32(struct tmio_sd_priv *priv, u32 addr, u32 val) |
| { |
| /* write mode */ |
| tmio_sd_writel(priv, RENESAS_SDHI_SCC_TMPPORT5_DLL_RW_SEL_W | |
| (RENESAS_SDHI_SCC_TMPPORT5_DLL_ADR_MASK & addr), |
| RENESAS_SDHI_SCC_TMPPORT5); |
| tmio_sd_writel(priv, val, RENESAS_SDHI_SCC_TMPPORT6); |
| |
| /* access start and stop */ |
| tmio_sd_writel(priv, RENESAS_SDHI_SCC_TMPPORT4_DLL_ACC_START, |
| RENESAS_SDHI_SCC_TMPPORT4); |
| tmio_sd_writel(priv, 0, RENESAS_SDHI_SCC_TMPPORT4); |
| } |
| |
| static bool renesas_sdhi_check_scc_error(struct udevice *dev) |
| { |
| struct tmio_sd_priv *priv = dev_get_priv(dev); |
| struct mmc *mmc = mmc_get_mmc_dev(dev); |
| unsigned long new_tap = priv->tap_set; |
| unsigned long error_tap = priv->tap_set; |
| u32 reg, smpcmp; |
| |
| if ((priv->caps & TMIO_SD_CAP_RCAR_UHS) && |
| (mmc->selected_mode != UHS_SDR104) && |
| (mmc->selected_mode != MMC_HS_200) && |
| (mmc->selected_mode != MMC_HS_400) && |
| (priv->nrtaps != 4)) |
| return false; |
| |
| reg = tmio_sd_readl(priv, RENESAS_SDHI_SCC_RVSCNTL); |
| /* Handle automatic tuning correction */ |
| if (reg & RENESAS_SDHI_SCC_RVSCNTL_RVSEN) { |
| reg = tmio_sd_readl(priv, RENESAS_SDHI_SCC_RVSREQ); |
| if (reg & RENESAS_SDHI_SCC_RVSREQ_RVSERR) { |
| tmio_sd_writel(priv, 0, RENESAS_SDHI_SCC_RVSREQ); |
| return true; |
| } |
| |
| return false; |
| } |
| |
| /* Handle manual tuning correction */ |
| reg = tmio_sd_readl(priv, RENESAS_SDHI_SCC_RVSREQ); |
| if (!reg) /* No error */ |
| return false; |
| |
| tmio_sd_writel(priv, 0, RENESAS_SDHI_SCC_RVSREQ); |
| |
| if (mmc->selected_mode == MMC_HS_400) { |
| /* |
| * Correction Error Status contains CMD and DAT signal status. |
| * In HS400, DAT signal based on DS signal, not CLK. |
| * Therefore, use only CMD status. |
| */ |
| smpcmp = tmio_sd_readl(priv, RENESAS_SDHI_SCC_SMPCMP) & |
| RENESAS_SDHI_SCC_SMPCMP_CMD_ERR; |
| |
| switch (smpcmp) { |
| case 0: |
| return false; /* No error in CMD signal */ |
| case RENESAS_SDHI_SCC_SMPCMP_CMD_REQUP: |
| new_tap = (priv->tap_set + |
| priv->tap_num + 1) % priv->tap_num; |
| error_tap = (priv->tap_set + |
| priv->tap_num - 1) % priv->tap_num; |
| break; |
| case RENESAS_SDHI_SCC_SMPCMP_CMD_REQDOWN: |
| new_tap = (priv->tap_set + |
| priv->tap_num - 1) % priv->tap_num; |
| error_tap = (priv->tap_set + |
| priv->tap_num + 1) % priv->tap_num; |
| break; |
| default: |
| return true; /* Need re-tune */ |
| } |
| |
| if (priv->hs400_bad_tap & BIT(new_tap)) { |
| /* |
| * New tap is bad tap (cannot change). |
| * Compare with HS200 tuning result. |
| * In HS200 tuning, when smpcmp[error_tap] |
| * is OK, retune is executed. |
| */ |
| if (priv->smpcmp & BIT(error_tap)) |
| return true; /* Need retune */ |
| |
| return false; /* cannot change */ |
| } |
| |
| priv->tap_set = new_tap; |
| } else { |
| if (reg & RENESAS_SDHI_SCC_RVSREQ_RVSERR) |
| return true; /* Need re-tune */ |
| else if (reg & RENESAS_SDHI_SCC_RVSREQ_REQTAPUP) |
| priv->tap_set = (priv->tap_set + |
| priv->tap_num + 1) % priv->tap_num; |
| else if (reg & RENESAS_SDHI_SCC_RVSREQ_REQTAPDOWN) |
| priv->tap_set = (priv->tap_set + |
| priv->tap_num - 1) % priv->tap_num; |
| else |
| return false; |
| } |
| |
| /* Set TAP position */ |
| tmio_sd_writel(priv, priv->tap_set >> ((priv->nrtaps == 4) ? 1 : 0), |
| RENESAS_SDHI_SCC_TAPSET); |
| |
| return false; |
| } |
| |
| static void renesas_sdhi_adjust_hs400_mode_enable(struct tmio_sd_priv *priv) |
| { |
| u32 calib_code; |
| |
| if (!priv->adjust_hs400_enable) |
| return; |
| |
| if (!priv->needs_adjust_hs400) |
| return; |
| |
| if (!priv->adjust_hs400_calib_table) |
| return; |
| |
| /* |
| * Enabled Manual adjust HS400 mode |
| * |
| * 1) Disabled Write Protect |
| * W(addr=0x00, WP_DISABLE_CODE) |
| * |
| * 2) Read Calibration code |
| * read_value = R(addr=0x26) |
| * 3) Refer to calibration table |
| * Calibration code = table[read_value] |
| * 4) Enabled Manual Calibration |
| * W(addr=0x22, manual mode | Calibration code) |
| * 5) Set Offset value to TMPPORT3 Reg |
| */ |
| sd_scc_tmpport_write32(priv, 0x00, |
| RENESAS_SDHI_SCC_TMPPORT_DISABLE_WP_CODE); |
| calib_code = sd_scc_tmpport_read32(priv, 0x26); |
| calib_code &= RENESAS_SDHI_SCC_TMPPORT_CALIB_CODE_MASK; |
| sd_scc_tmpport_write32(priv, 0x22, |
| RENESAS_SDHI_SCC_TMPPORT_MANUAL_MODE | |
| priv->adjust_hs400_calib_table[calib_code]); |
| tmio_sd_writel(priv, priv->adjust_hs400_offset, |
| RENESAS_SDHI_SCC_TMPPORT3); |
| |
| /* Clear flag */ |
| priv->needs_adjust_hs400 = false; |
| } |
| |
| static void renesas_sdhi_adjust_hs400_mode_disable(struct tmio_sd_priv *priv) |
| { |
| |
| /* Disabled Manual adjust HS400 mode |
| * |
| * 1) Disabled Write Protect |
| * W(addr=0x00, WP_DISABLE_CODE) |
| * 2) Disabled Manual Calibration |
| * W(addr=0x22, 0) |
| * 3) Clear offset value to TMPPORT3 Reg |
| */ |
| sd_scc_tmpport_write32(priv, 0x00, |
| RENESAS_SDHI_SCC_TMPPORT_DISABLE_WP_CODE); |
| sd_scc_tmpport_write32(priv, 0x22, 0); |
| tmio_sd_writel(priv, 0, RENESAS_SDHI_SCC_TMPPORT3); |
| } |
| |
| static unsigned int renesas_sdhi_init_tuning(struct tmio_sd_priv *priv) |
| { |
| u32 reg; |
| |
| /* Initialize SCC */ |
| tmio_sd_writel(priv, 0, TMIO_SD_INFO1); |
| |
| reg = tmio_sd_readl(priv, TMIO_SD_CLKCTL); |
| reg &= ~TMIO_SD_CLKCTL_SCLKEN; |
| tmio_sd_writel(priv, reg, TMIO_SD_CLKCTL); |
| |
| /* Set sampling clock selection range */ |
| tmio_sd_writel(priv, (0x8 << RENESAS_SDHI_SCC_DTCNTL_TAPNUM_SHIFT) | |
| RENESAS_SDHI_SCC_DTCNTL_TAPEN, |
| RENESAS_SDHI_SCC_DTCNTL); |
| |
| reg = tmio_sd_readl(priv, RENESAS_SDHI_SCC_CKSEL); |
| reg |= RENESAS_SDHI_SCC_CKSEL_DTSEL; |
| tmio_sd_writel(priv, reg, RENESAS_SDHI_SCC_CKSEL); |
| |
| reg = tmio_sd_readl(priv, RENESAS_SDHI_SCC_RVSCNTL); |
| reg &= ~RENESAS_SDHI_SCC_RVSCNTL_RVSEN; |
| tmio_sd_writel(priv, reg, RENESAS_SDHI_SCC_RVSCNTL); |
| |
| tmio_sd_writel(priv, 0x300 /* scc_tappos */, |
| RENESAS_SDHI_SCC_DT2FF); |
| |
| reg = tmio_sd_readl(priv, TMIO_SD_CLKCTL); |
| reg |= TMIO_SD_CLKCTL_SCLKEN; |
| tmio_sd_writel(priv, reg, TMIO_SD_CLKCTL); |
| |
| /* Read TAPNUM */ |
| return (tmio_sd_readl(priv, RENESAS_SDHI_SCC_DTCNTL) >> |
| RENESAS_SDHI_SCC_DTCNTL_TAPNUM_SHIFT) & |
| RENESAS_SDHI_SCC_DTCNTL_TAPNUM_MASK; |
| } |
| |
| static void renesas_sdhi_reset_tuning(struct tmio_sd_priv *priv) |
| { |
| u32 reg; |
| |
| /* Reset SCC */ |
| reg = tmio_sd_readl(priv, TMIO_SD_CLKCTL); |
| reg &= ~TMIO_SD_CLKCTL_SCLKEN; |
| tmio_sd_writel(priv, reg, TMIO_SD_CLKCTL); |
| |
| reg = tmio_sd_readl(priv, RENESAS_SDHI_SCC_CKSEL); |
| reg &= ~RENESAS_SDHI_SCC_CKSEL_DTSEL; |
| tmio_sd_writel(priv, reg, RENESAS_SDHI_SCC_CKSEL); |
| |
| reg = tmio_sd_readl(priv, RENESAS_SDHI_SCC_TMPPORT2); |
| reg &= ~(RENESAS_SDHI_SCC_TMPPORT2_HS400EN | |
| RENESAS_SDHI_SCC_TMPPORT2_HS400OSEL); |
| tmio_sd_writel(priv, reg, RENESAS_SDHI_SCC_TMPPORT2); |
| |
| /* Disable HS400 mode adjustment */ |
| renesas_sdhi_adjust_hs400_mode_disable(priv); |
| |
| reg = tmio_sd_readl(priv, TMIO_SD_CLKCTL); |
| reg |= TMIO_SD_CLKCTL_SCLKEN; |
| tmio_sd_writel(priv, reg, TMIO_SD_CLKCTL); |
| |
| reg = tmio_sd_readl(priv, RENESAS_SDHI_SCC_RVSCNTL); |
| reg &= ~RENESAS_SDHI_SCC_RVSCNTL_RVSEN; |
| tmio_sd_writel(priv, reg, RENESAS_SDHI_SCC_RVSCNTL); |
| |
| reg = tmio_sd_readl(priv, RENESAS_SDHI_SCC_RVSCNTL); |
| reg &= ~RENESAS_SDHI_SCC_RVSCNTL_RVSEN; |
| tmio_sd_writel(priv, reg, RENESAS_SDHI_SCC_RVSCNTL); |
| } |
| |
| static int renesas_sdhi_hs400(struct udevice *dev) |
| { |
| struct tmio_sd_priv *priv = dev_get_priv(dev); |
| struct mmc *mmc = mmc_get_mmc_dev(dev); |
| bool hs400 = (mmc->selected_mode == MMC_HS_400); |
| int ret, taps = hs400 ? priv->nrtaps : 8; |
| const u32 sdn_rate = 200000000; |
| u32 sdnh_rate = 800000000; |
| unsigned long new_tap; |
| u32 reg; |
| |
| if (clk_valid(&priv->clkh) && !priv->needs_clkh_fallback) { |
| /* HS400 on 4tap SoC => SDnH=400 MHz, SDn=200 MHz */ |
| if (taps == 4) |
| sdnh_rate /= 2; |
| ret = clk_set_rate(&priv->clkh, sdnh_rate); |
| if (ret < 0) |
| return ret; |
| } |
| |
| ret = clk_set_rate(&priv->clk, sdn_rate); |
| if (ret < 0) |
| return ret; |
| |
| reg = tmio_sd_readl(priv, RENESAS_SDHI_SCC_RVSCNTL); |
| reg &= ~RENESAS_SDHI_SCC_RVSCNTL_RVSEN; |
| tmio_sd_writel(priv, reg, RENESAS_SDHI_SCC_RVSCNTL); |
| |
| reg = tmio_sd_readl(priv, RENESAS_SDHI_SCC_TMPPORT2); |
| if (hs400) { |
| reg |= RENESAS_SDHI_SCC_TMPPORT2_HS400EN | |
| RENESAS_SDHI_SCC_TMPPORT2_HS400OSEL; |
| } else { |
| reg &= ~(RENESAS_SDHI_SCC_TMPPORT2_HS400EN | |
| RENESAS_SDHI_SCC_TMPPORT2_HS400OSEL); |
| } |
| |
| tmio_sd_writel(priv, reg, RENESAS_SDHI_SCC_TMPPORT2); |
| |
| /* Disable HS400 mode adjustment */ |
| if (!hs400) |
| renesas_sdhi_adjust_hs400_mode_disable(priv); |
| |
| tmio_sd_writel(priv, (0x8 << RENESAS_SDHI_SCC_DTCNTL_TAPNUM_SHIFT) | |
| RENESAS_SDHI_SCC_DTCNTL_TAPEN, |
| RENESAS_SDHI_SCC_DTCNTL); |
| |
| /* Avoid bad TAP */ |
| if (priv->hs400_bad_tap & BIT(priv->tap_set)) { |
| new_tap = (priv->tap_set + |
| priv->tap_num + 1) % priv->tap_num; |
| |
| if (priv->hs400_bad_tap & BIT(new_tap)) |
| new_tap = (priv->tap_set + |
| priv->tap_num - 1) % priv->tap_num; |
| |
| if (priv->hs400_bad_tap & BIT(new_tap)) { |
| new_tap = priv->tap_set; |
| debug("Three consecutive bad tap is prohibited\n"); |
| } |
| |
| priv->tap_set = new_tap; |
| tmio_sd_writel(priv, priv->tap_set, RENESAS_SDHI_SCC_TAPSET); |
| } |
| |
| if (taps == 4) { |
| tmio_sd_writel(priv, priv->tap_set >> 1, |
| RENESAS_SDHI_SCC_TAPSET); |
| tmio_sd_writel(priv, hs400 ? 0x100 : 0x300, |
| RENESAS_SDHI_SCC_DT2FF); |
| } else { |
| tmio_sd_writel(priv, priv->tap_set, RENESAS_SDHI_SCC_TAPSET); |
| tmio_sd_writel(priv, 0x300, RENESAS_SDHI_SCC_DT2FF); |
| } |
| |
| reg = tmio_sd_readl(priv, RENESAS_SDHI_SCC_CKSEL); |
| reg |= RENESAS_SDHI_SCC_CKSEL_DTSEL; |
| tmio_sd_writel(priv, reg, RENESAS_SDHI_SCC_CKSEL); |
| |
| /* Execute adjust hs400 offset after setting to HS400 mode */ |
| if (hs400) |
| priv->needs_adjust_hs400 = true; |
| |
| return 0; |
| } |
| |
| static void renesas_sdhi_prepare_tuning(struct tmio_sd_priv *priv, |
| unsigned long tap) |
| { |
| /* Set sampling clock position */ |
| tmio_sd_writel(priv, tap, RENESAS_SDHI_SCC_TAPSET); |
| } |
| |
| static unsigned int renesas_sdhi_compare_scc_data(struct tmio_sd_priv *priv) |
| { |
| /* Get comparison of sampling data */ |
| return tmio_sd_readl(priv, RENESAS_SDHI_SCC_SMPCMP); |
| } |
| |
| static int renesas_sdhi_select_tuning(struct tmio_sd_priv *priv, |
| unsigned int taps) |
| { |
| unsigned long tap_cnt; /* counter of tuning success */ |
| unsigned long tap_start;/* start position of tuning success */ |
| unsigned long tap_end; /* end position of tuning success */ |
| unsigned long ntap; /* temporary counter of tuning success */ |
| unsigned long match_cnt;/* counter of matching data */ |
| unsigned long i; |
| bool select = false; |
| u32 reg; |
| |
| priv->needs_adjust_hs400 = false; |
| |
| /* Clear SCC_RVSREQ */ |
| tmio_sd_writel(priv, 0, RENESAS_SDHI_SCC_RVSREQ); |
| |
| /* Merge the results */ |
| for (i = 0; i < priv->tap_num * 2; i++) { |
| if (!(taps & BIT(i))) { |
| taps &= ~BIT(i % priv->tap_num); |
| taps &= ~BIT((i % priv->tap_num) + priv->tap_num); |
| } |
| if (!(priv->smpcmp & BIT(i))) { |
| priv->smpcmp &= ~BIT(i % priv->tap_num); |
| priv->smpcmp &= ~BIT((i % priv->tap_num) + priv->tap_num); |
| } |
| } |
| |
| /* |
| * Find the longest consecutive run of successful probes. If that |
| * is more than RENESAS_SDHI_MAX_TAP probes long then use the |
| * center index as the tap. |
| */ |
| tap_cnt = 0; |
| ntap = 0; |
| tap_start = 0; |
| tap_end = 0; |
| for (i = 0; i < priv->tap_num * 2; i++) { |
| if (taps & BIT(i)) |
| ntap++; |
| else { |
| if (ntap > tap_cnt) { |
| tap_start = i - ntap; |
| tap_end = i - 1; |
| tap_cnt = ntap; |
| } |
| ntap = 0; |
| } |
| } |
| |
| if (ntap > tap_cnt) { |
| tap_start = i - ntap; |
| tap_end = i - 1; |
| tap_cnt = ntap; |
| } |
| |
| /* |
| * If all of the TAP is OK, the sampling clock position is selected by |
| * identifying the change point of data. |
| */ |
| if (tap_cnt == priv->tap_num * 2) { |
| match_cnt = 0; |
| ntap = 0; |
| tap_start = 0; |
| tap_end = 0; |
| for (i = 0; i < priv->tap_num * 2; i++) { |
| if (priv->smpcmp & BIT(i)) |
| ntap++; |
| else { |
| if (ntap > match_cnt) { |
| tap_start = i - ntap; |
| tap_end = i - 1; |
| match_cnt = ntap; |
| } |
| ntap = 0; |
| } |
| } |
| if (ntap > match_cnt) { |
| tap_start = i - ntap; |
| tap_end = i - 1; |
| match_cnt = ntap; |
| } |
| if (match_cnt) |
| select = true; |
| } else if (tap_cnt >= RENESAS_SDHI_MAX_TAP) |
| select = true; |
| |
| if (select) |
| priv->tap_set = ((tap_start + tap_end) / 2) % priv->tap_num; |
| else |
| return -EIO; |
| |
| /* Set SCC */ |
| tmio_sd_writel(priv, priv->tap_set, RENESAS_SDHI_SCC_TAPSET); |
| |
| /* Enable auto re-tuning */ |
| reg = tmio_sd_readl(priv, RENESAS_SDHI_SCC_RVSCNTL); |
| reg |= RENESAS_SDHI_SCC_RVSCNTL_RVSEN; |
| tmio_sd_writel(priv, reg, RENESAS_SDHI_SCC_RVSCNTL); |
| |
| return 0; |
| } |
| |
| int renesas_sdhi_execute_tuning(struct udevice *dev, uint opcode) |
| { |
| struct tmio_sd_priv *priv = dev_get_priv(dev); |
| struct mmc_uclass_priv *upriv = dev_get_uclass_priv(dev); |
| struct mmc *mmc = upriv->mmc; |
| unsigned int tap_num; |
| unsigned int taps = 0; |
| int i, ret = 0; |
| u32 caps; |
| |
| /* Only supported on Renesas RCar */ |
| if (!(priv->caps & TMIO_SD_CAP_RCAR_UHS)) |
| return -EINVAL; |
| |
| /* clock tuning is not needed for upto 52MHz */ |
| if (!((mmc->selected_mode == MMC_HS_200) || |
| (mmc->selected_mode == MMC_HS_400) || |
| (mmc->selected_mode == UHS_SDR104) || |
| (mmc->selected_mode == UHS_SDR50))) |
| return 0; |
| |
| tap_num = renesas_sdhi_init_tuning(priv); |
| if (!tap_num) |
| /* Tuning is not supported */ |
| goto out; |
| |
| priv->tap_num = tap_num; |
| |
| if (priv->tap_num * 2 >= sizeof(taps) * 8) { |
| dev_err(dev, |
| "Too many taps, skipping tuning. Please consider updating size of taps field of tmio_mmc_host\n"); |
| goto out; |
| } |
| |
| priv->smpcmp = 0; |
| |
| /* Issue CMD19 twice for each tap */ |
| for (i = 0; i < 2 * priv->tap_num; i++) { |
| renesas_sdhi_prepare_tuning(priv, i % priv->tap_num); |
| |
| /* Force PIO for the tuning */ |
| caps = priv->caps; |
| priv->caps &= ~TMIO_SD_CAP_DMA_INTERNAL; |
| |
| ret = mmc_send_tuning(mmc, opcode, NULL); |
| |
| priv->caps = caps; |
| |
| if (ret == 0) |
| taps |= BIT(i); |
| |
| ret = renesas_sdhi_compare_scc_data(priv); |
| if (ret == 0) |
| priv->smpcmp |= BIT(i); |
| |
| mdelay(1); |
| |
| /* |
| * eMMC specification specifies that CMD12 can be used to stop a tuning |
| * command, but SD specification does not, so do nothing unless it is |
| * eMMC. |
| */ |
| if (ret && (opcode == MMC_CMD_SEND_TUNING_BLOCK_HS200)) { |
| ret = mmc_send_stop_transmission(mmc, false); |
| if (ret < 0) |
| dev_dbg(dev, "Tuning abort fail (%d)\n", ret); |
| } |
| } |
| |
| ret = renesas_sdhi_select_tuning(priv, taps); |
| |
| out: |
| if (ret < 0) { |
| dev_warn(dev, "Tuning procedure failed\n"); |
| renesas_sdhi_reset_tuning(priv); |
| } |
| |
| return ret; |
| } |
| #else |
| static int renesas_sdhi_hs400(struct udevice *dev) |
| { |
| return 0; |
| } |
| #endif |
| |
| static int renesas_sdhi_set_ios(struct udevice *dev) |
| { |
| struct tmio_sd_priv *priv = dev_get_priv(dev); |
| u32 tmp; |
| int ret; |
| |
| /* Stop the clock before changing its rate to avoid a glitch signal */ |
| tmp = tmio_sd_readl(priv, TMIO_SD_CLKCTL); |
| tmp &= ~TMIO_SD_CLKCTL_SCLKEN; |
| tmio_sd_writel(priv, tmp, TMIO_SD_CLKCTL); |
| |
| ret = renesas_sdhi_hs400(dev); |
| if (ret) |
| return ret; |
| |
| ret = tmio_sd_set_ios(dev); |
| |
| mdelay(10); |
| |
| #if CONFIG_IS_ENABLED(MMC_UHS_SUPPORT) || \ |
| CONFIG_IS_ENABLED(MMC_HS200_SUPPORT) || \ |
| CONFIG_IS_ENABLED(MMC_HS400_SUPPORT) |
| struct mmc *mmc = mmc_get_mmc_dev(dev); |
| if ((priv->caps & TMIO_SD_CAP_RCAR_UHS) && |
| (mmc->selected_mode != UHS_SDR104) && |
| (mmc->selected_mode != MMC_HS_200) && |
| (mmc->selected_mode != MMC_HS_400)) { |
| renesas_sdhi_reset_tuning(priv); |
| } |
| #endif |
| |
| return ret; |
| } |
| |
| #if CONFIG_IS_ENABLED(MMC_UHS_SUPPORT) |
| static int renesas_sdhi_wait_dat0(struct udevice *dev, int state, |
| int timeout_us) |
| { |
| int ret = -ETIMEDOUT; |
| bool dat0_high; |
| bool target_dat0_high = !!state; |
| struct tmio_sd_priv *priv = dev_get_priv(dev); |
| |
| timeout_us = DIV_ROUND_UP(timeout_us, 10); /* check every 10 us. */ |
| while (timeout_us--) { |
| dat0_high = !!(tmio_sd_readl(priv, TMIO_SD_INFO2) & TMIO_SD_INFO2_DAT0); |
| if (dat0_high == target_dat0_high) { |
| ret = 0; |
| break; |
| } |
| udelay(10); |
| } |
| |
| return ret; |
| } |
| #endif |
| |
| #define RENESAS_SDHI_DMA_ALIGNMENT 128 |
| |
| static int renesas_sdhi_addr_aligned_gen(uintptr_t ubuf, |
| size_t len, size_t len_aligned) |
| { |
| /* Check if start is aligned */ |
| if (!IS_ALIGNED(ubuf, RENESAS_SDHI_DMA_ALIGNMENT)) { |
| debug("Unaligned buffer address %lx\n", ubuf); |
| return 0; |
| } |
| |
| /* Check if length is aligned */ |
| if (len != len_aligned) { |
| debug("Unaligned buffer length %zu\n", len); |
| return 0; |
| } |
| |
| #ifdef CONFIG_PHYS_64BIT |
| /* Check if below 32bit boundary */ |
| if ((ubuf >> 32) || (ubuf + len_aligned) >> 32) { |
| debug("Buffer above 32bit boundary %lx-%lx\n", |
| ubuf, ubuf + len_aligned); |
| return 0; |
| } |
| #endif |
| |
| /* Aligned */ |
| return 1; |
| } |
| |
| static int renesas_sdhi_addr_aligned(struct bounce_buffer *state) |
| { |
| uintptr_t ubuf = (uintptr_t)state->user_buffer; |
| |
| return renesas_sdhi_addr_aligned_gen(ubuf, state->len, |
| state->len_aligned); |
| } |
| |
| static int renesas_sdhi_send_cmd(struct udevice *dev, struct mmc_cmd *cmd, |
| struct mmc_data *data) |
| { |
| struct bounce_buffer bbstate; |
| unsigned int bbflags; |
| bool bbok = false; |
| size_t len; |
| void *buf; |
| int ret; |
| |
| if (data) { |
| if (data->flags & MMC_DATA_READ) { |
| buf = data->dest; |
| bbflags = GEN_BB_WRITE; |
| } else { |
| buf = (void *)data->src; |
| bbflags = GEN_BB_READ; |
| } |
| len = data->blocks * data->blocksize; |
| |
| ret = bounce_buffer_start_extalign(&bbstate, buf, len, bbflags, |
| RENESAS_SDHI_DMA_ALIGNMENT, |
| renesas_sdhi_addr_aligned); |
| /* |
| * If the amount of data to transfer is too large, we can get |
| * -ENOMEM when starting the bounce buffer. If that happens, |
| * fall back to PIO as it was before, otherwise use the BB. |
| */ |
| if (!ret) { |
| bbok = true; |
| if (data->flags & MMC_DATA_READ) |
| data->dest = bbstate.bounce_buffer; |
| else |
| data->src = bbstate.bounce_buffer; |
| } |
| } |
| |
| ret = tmio_sd_send_cmd(dev, cmd, data); |
| |
| if (data && bbok) { |
| buf = bbstate.user_buffer; |
| |
| bounce_buffer_stop(&bbstate); |
| |
| if (data->flags & MMC_DATA_READ) |
| data->dest = buf; |
| else |
| data->src = buf; |
| } |
| |
| if (ret) |
| return ret; |
| |
| #if CONFIG_IS_ENABLED(MMC_UHS_SUPPORT) || \ |
| CONFIG_IS_ENABLED(MMC_HS200_SUPPORT) || \ |
| CONFIG_IS_ENABLED(MMC_HS400_SUPPORT) |
| struct tmio_sd_priv *priv = dev_get_priv(dev); |
| |
| renesas_sdhi_check_scc_error(dev); |
| |
| if (cmd->cmdidx == MMC_CMD_SEND_STATUS) |
| renesas_sdhi_adjust_hs400_mode_enable(priv); |
| #endif |
| |
| return 0; |
| } |
| |
| int renesas_sdhi_get_b_max(struct udevice *dev, void *dst, lbaint_t blkcnt) |
| { |
| struct tmio_sd_priv *priv = dev_get_priv(dev); |
| struct mmc_uclass_priv *upriv = dev_get_uclass_priv(dev); |
| struct mmc *mmc = upriv->mmc; |
| size_t len = blkcnt * mmc->read_bl_len; |
| size_t len_align = roundup(len, RENESAS_SDHI_DMA_ALIGNMENT); |
| |
| if (renesas_sdhi_addr_aligned_gen((uintptr_t)dst, len, len_align)) { |
| if (priv->quirks & TMIO_SD_CAP_16BIT) |
| return U16_MAX; |
| else |
| return U32_MAX; |
| } else { |
| return (CONFIG_SYS_MALLOC_LEN / 4) / mmc->read_bl_len; |
| } |
| } |
| |
| static const struct dm_mmc_ops renesas_sdhi_ops = { |
| .send_cmd = renesas_sdhi_send_cmd, |
| .set_ios = renesas_sdhi_set_ios, |
| .get_cd = tmio_sd_get_cd, |
| #if CONFIG_IS_ENABLED(MMC_UHS_SUPPORT) || \ |
| CONFIG_IS_ENABLED(MMC_HS200_SUPPORT) || \ |
| CONFIG_IS_ENABLED(MMC_HS400_SUPPORT) |
| .execute_tuning = renesas_sdhi_execute_tuning, |
| #endif |
| #if CONFIG_IS_ENABLED(MMC_UHS_SUPPORT) |
| .wait_dat0 = renesas_sdhi_wait_dat0, |
| #endif |
| .get_b_max = renesas_sdhi_get_b_max, |
| }; |
| |
| #define RENESAS_GEN2_QUIRKS TMIO_SD_CAP_RCAR_GEN2 |
| #define RENESAS_GEN3_QUIRKS \ |
| TMIO_SD_CAP_64BIT | TMIO_SD_CAP_RCAR_GEN3 | TMIO_SD_CAP_RCAR_UHS |
| |
| static const struct udevice_id renesas_sdhi_match[] = { |
| { .compatible = "renesas,sdhi-r8a7790", .data = RENESAS_GEN2_QUIRKS }, |
| { .compatible = "renesas,sdhi-r8a7791", .data = RENESAS_GEN2_QUIRKS }, |
| { .compatible = "renesas,sdhi-r8a7792", .data = RENESAS_GEN2_QUIRKS }, |
| { .compatible = "renesas,sdhi-r8a7793", .data = RENESAS_GEN2_QUIRKS }, |
| { .compatible = "renesas,sdhi-r8a7794", .data = RENESAS_GEN2_QUIRKS }, |
| { .compatible = "renesas,sdhi-r8a7795", .data = RENESAS_GEN3_QUIRKS }, |
| { .compatible = "renesas,sdhi-r8a7796", .data = RENESAS_GEN3_QUIRKS }, |
| { .compatible = "renesas,sdhi-r8a77961", .data = RENESAS_GEN3_QUIRKS }, |
| { .compatible = "renesas,rcar-gen3-sdhi", .data = RENESAS_GEN3_QUIRKS }, |
| { .compatible = "renesas,sdhi-r8a77965", .data = RENESAS_GEN3_QUIRKS }, |
| { .compatible = "renesas,sdhi-r8a77970", .data = RENESAS_GEN3_QUIRKS }, |
| { .compatible = "renesas,sdhi-r8a77990", .data = RENESAS_GEN3_QUIRKS }, |
| { .compatible = "renesas,sdhi-r8a77995", .data = RENESAS_GEN3_QUIRKS }, |
| { .compatible = "renesas,rcar-gen4-sdhi", .data = RENESAS_GEN3_QUIRKS }, |
| { /* sentinel */ } |
| }; |
| |
| static ulong renesas_sdhi_clk_get_rate(struct tmio_sd_priv *priv) |
| { |
| return clk_get_rate(&priv->clk); |
| } |
| |
| static void renesas_sdhi_filter_caps(struct udevice *dev) |
| { |
| struct tmio_sd_priv *priv = dev_get_priv(dev); |
| |
| if (!(priv->caps & TMIO_SD_CAP_RCAR_GEN3)) |
| return; |
| |
| if (priv->caps & TMIO_SD_CAP_DMA_INTERNAL) |
| priv->idma_bus_width = TMIO_SD_DMA_MODE_BUS_WIDTH; |
| |
| #if CONFIG_IS_ENABLED(MMC_UHS_SUPPORT) || \ |
| CONFIG_IS_ENABLED(MMC_HS200_SUPPORT) || \ |
| CONFIG_IS_ENABLED(MMC_HS400_SUPPORT) |
| struct tmio_sd_plat *plat = dev_get_plat(dev); |
| |
| /* HS400 is not supported on H3 ES1.x, M3W ES1.[012], V3M, V3H ES1.x, D3 */ |
| if (((rmobile_get_cpu_type() == RMOBILE_CPU_TYPE_R8A7795) && |
| (rmobile_get_cpu_rev_integer() <= 1)) || |
| ((rmobile_get_cpu_type() == RMOBILE_CPU_TYPE_R8A7796) && |
| (rmobile_get_cpu_rev_integer() == 1) && |
| (rmobile_get_cpu_rev_fraction() <= 2)) || |
| (rmobile_get_cpu_type() == RMOBILE_CPU_TYPE_R8A77970) || |
| ((rmobile_get_cpu_type() == RMOBILE_CPU_TYPE_R8A77980) && |
| (rmobile_get_cpu_rev_integer() <= 1)) || |
| (rmobile_get_cpu_type() == RMOBILE_CPU_TYPE_R8A77995)) |
| plat->cfg.host_caps &= ~MMC_MODE_HS400; |
| |
| /* H3 ES2.0, ES3.0 and M3W ES1.2 and M3N bad taps */ |
| if (((rmobile_get_cpu_type() == RMOBILE_CPU_TYPE_R8A7795) && |
| (rmobile_get_cpu_rev_integer() >= 2)) || |
| ((rmobile_get_cpu_type() == RMOBILE_CPU_TYPE_R8A7796) && |
| (rmobile_get_cpu_rev_integer() == 1) && |
| (rmobile_get_cpu_rev_fraction() == 2)) || |
| (rmobile_get_cpu_type() == RMOBILE_CPU_TYPE_R8A77965)) |
| priv->hs400_bad_tap = BIT(2) | BIT(3) | BIT(6) | BIT(7); |
| |
| /* M3W ES1.x for x>2 can use HS400 with manual adjustment and taps */ |
| if ((rmobile_get_cpu_type() == RMOBILE_CPU_TYPE_R8A7796) && |
| (rmobile_get_cpu_rev_integer() == 1) && |
| (rmobile_get_cpu_rev_fraction() > 2)) { |
| priv->adjust_hs400_enable = true; |
| priv->adjust_hs400_offset = 3; |
| priv->hs400_bad_tap = BIT(1) | BIT(3) | BIT(5) | BIT(7); |
| priv->adjust_hs400_calib_table = |
| r8a7796_rev13_calib_table[!rmobile_is_gen3_mmc0(priv)]; |
| } |
| |
| /* M3W+ bad taps */ |
| if ((rmobile_get_cpu_type() == RMOBILE_CPU_TYPE_R8A7796) && |
| (rmobile_get_cpu_rev_integer() == 3)) |
| priv->hs400_bad_tap = BIT(1) | BIT(3) | BIT(5) | BIT(7); |
| |
| /* M3N can use HS400 with manual adjustment */ |
| if (rmobile_get_cpu_type() == RMOBILE_CPU_TYPE_R8A77965) { |
| priv->adjust_hs400_enable = true; |
| priv->adjust_hs400_offset = 3; |
| priv->adjust_hs400_calib_table = |
| r8a77965_calib_table[!rmobile_is_gen3_mmc0(priv)]; |
| } |
| |
| /* E3 can use HS400 with manual adjustment */ |
| if (rmobile_get_cpu_type() == RMOBILE_CPU_TYPE_R8A77990) { |
| priv->adjust_hs400_enable = true; |
| priv->adjust_hs400_offset = 3; |
| priv->adjust_hs400_calib_table = |
| r8a77990_calib_table[!rmobile_is_gen3_mmc0(priv)]; |
| } |
| |
| /* H3 ES1.x, ES2.0 and M3W ES1.[0123] uses 4 tuning taps */ |
| if (((rmobile_get_cpu_type() == RMOBILE_CPU_TYPE_R8A7795) && |
| (rmobile_get_cpu_rev_integer() <= 2)) || |
| ((rmobile_get_cpu_type() == RMOBILE_CPU_TYPE_R8A7796) && |
| (rmobile_get_cpu_rev_integer() == 1) && |
| (rmobile_get_cpu_rev_fraction() <= 3))) |
| priv->nrtaps = 4; |
| else |
| priv->nrtaps = 8; |
| #endif |
| /* H3 ES1.x and M3W ES1.0 uses bit 17 for DTRAEND */ |
| if (((rmobile_get_cpu_type() == RMOBILE_CPU_TYPE_R8A7795) && |
| (rmobile_get_cpu_rev_integer() <= 1)) || |
| ((rmobile_get_cpu_type() == RMOBILE_CPU_TYPE_R8A7796) && |
| (rmobile_get_cpu_rev_integer() == 1) && |
| (rmobile_get_cpu_rev_fraction() == 0))) |
| priv->read_poll_flag = TMIO_SD_DMA_INFO1_END_RD; |
| else |
| priv->read_poll_flag = TMIO_SD_DMA_INFO1_END_RD2; |
| |
| /* V3M handles SD0H differently than other Gen3 SoCs */ |
| if (rmobile_get_cpu_type() == RMOBILE_CPU_TYPE_R8A77970) |
| priv->needs_clkh_fallback = true; |
| else |
| priv->needs_clkh_fallback = false; |
| } |
| |
| static int rzg2l_sdhi_setup(struct udevice *dev) |
| { |
| struct tmio_sd_priv *priv = dev_get_priv(dev); |
| struct clk imclk2, aclk; |
| struct reset_ctl rst; |
| int ret; |
| |
| /* |
| * On members of the RZ/G2L SoC family, we need to enable |
| * additional chip detect and bus clocks, then release the SDHI |
| * module from reset. |
| */ |
| ret = clk_get_by_name(dev, "cd", &imclk2); |
| if (ret < 0) { |
| dev_err(dev, "failed to get imclk2 (chip detect clk)\n"); |
| goto err_get_imclk2; |
| } |
| |
| ret = clk_get_by_name(dev, "aclk", &aclk); |
| if (ret < 0) { |
| dev_err(dev, "failed to get aclk\n"); |
| goto err_get_aclk; |
| } |
| |
| ret = clk_enable(&imclk2); |
| if (ret < 0) { |
| dev_err(dev, "failed to enable imclk2 (chip detect clk)\n"); |
| goto err_imclk2; |
| } |
| |
| ret = clk_enable(&aclk); |
| if (ret < 0) { |
| dev_err(dev, "failed to enable aclk\n"); |
| goto err_aclk; |
| } |
| |
| ret = reset_get_by_index(dev, 0, &rst); |
| if (ret < 0) { |
| dev_err(dev, "failed to get reset line\n"); |
| goto err_reset; |
| } |
| |
| ret = reset_deassert(&rst); |
| if (ret < 0) { |
| dev_err(dev, "failed to de-assert reset line\n"); |
| goto err_reset; |
| } |
| |
| ret = tmio_sd_probe(dev, priv->quirks); |
| if (ret) |
| goto err_tmio_probe; |
| |
| return 0; |
| |
| err_tmio_probe: |
| reset_assert(&rst); |
| err_reset: |
| clk_disable(&aclk); |
| err_aclk: |
| clk_disable(&imclk2); |
| err_imclk2: |
| clk_free(&aclk); |
| err_get_aclk: |
| clk_free(&imclk2); |
| err_get_imclk2: |
| return ret; |
| } |
| |
| static int renesas_sdhi_probe(struct udevice *dev) |
| { |
| struct tmio_sd_priv *priv = dev_get_priv(dev); |
| struct fdt_resource reg_res; |
| DECLARE_GLOBAL_DATA_PTR; |
| int ret; |
| |
| priv->clk_get_rate = renesas_sdhi_clk_get_rate; |
| |
| priv->quirks = dev_get_driver_data(dev); |
| if (priv->quirks == RENESAS_GEN2_QUIRKS) { |
| ret = fdt_get_resource(gd->fdt_blob, dev_of_offset(dev), |
| "reg", 0, ®_res); |
| if (ret < 0) { |
| dev_err(dev, "\"reg\" resource not found, ret=%i\n", |
| ret); |
| return ret; |
| } |
| |
| if (fdt_resource_size(®_res) == 0x100) |
| priv->quirks |= TMIO_SD_CAP_16BIT; |
| } |
| |
| ret = clk_get_by_index(dev, 0, &priv->clk); |
| if (ret < 0) { |
| dev_err(dev, "failed to get host clock\n"); |
| return ret; |
| } |
| |
| /* optional SDnH clock */ |
| ret = clk_get_by_name(dev, "clkh", &priv->clkh); |
| if (ret < 0) { |
| dev_dbg(dev, "failed to get clkh\n"); |
| } else { |
| ret = clk_set_rate(&priv->clkh, 800000000); |
| if (ret < 0) { |
| dev_err(dev, "failed to set rate for SDnH clock (%d)\n", ret); |
| goto err_clk; |
| } |
| } |
| |
| /* set to max rate */ |
| ret = clk_set_rate(&priv->clk, 200000000); |
| if (ret < 0) { |
| dev_err(dev, "failed to set rate for SDn clock (%d)\n", ret); |
| goto err_clkh; |
| } |
| |
| ret = clk_enable(&priv->clk); |
| if (ret) { |
| dev_err(dev, "failed to enable SDn clock (%d)\n", ret); |
| goto err_clkh; |
| } |
| |
| if (device_is_compatible(dev, "renesas,sdhi-r9a07g044")) |
| ret = rzg2l_sdhi_setup(dev); |
| else |
| ret = tmio_sd_probe(dev, priv->quirks); |
| if (ret) |
| goto err_tmio_probe; |
| |
| renesas_sdhi_filter_caps(dev); |
| |
| #if CONFIG_IS_ENABLED(MMC_UHS_SUPPORT) || \ |
| CONFIG_IS_ENABLED(MMC_HS200_SUPPORT) || \ |
| CONFIG_IS_ENABLED(MMC_HS400_SUPPORT) |
| if (priv->caps & TMIO_SD_CAP_RCAR_UHS) |
| renesas_sdhi_reset_tuning(priv); |
| #endif |
| return 0; |
| |
| err_tmio_probe: |
| clk_disable(&priv->clk); |
| err_clkh: |
| clk_free(&priv->clkh); |
| err_clk: |
| clk_free(&priv->clk); |
| return ret; |
| } |
| |
| U_BOOT_DRIVER(renesas_sdhi) = { |
| .name = "renesas-sdhi", |
| .id = UCLASS_MMC, |
| .of_match = renesas_sdhi_match, |
| .bind = tmio_sd_bind, |
| .probe = renesas_sdhi_probe, |
| .priv_auto = sizeof(struct tmio_sd_priv), |
| .plat_auto = sizeof(struct tmio_sd_plat), |
| .ops = &renesas_sdhi_ops, |
| }; |