| // SPDX-License-Identifier: GPL-2.0+ |
| /* |
| * (C) Copyright 2016 |
| * Author: Amit Singh Tomar, amittomer25@gmail.com |
| * |
| * Ethernet driver for H3/A64/A83T based SoC's |
| * |
| * It is derived from the work done by |
| * LABBE Corentin & Chen-Yu Tsai for Linux, THANKS! |
| * |
| */ |
| |
| #include <cpu_func.h> |
| #include <asm/io.h> |
| #include <asm/arch/clock.h> |
| #include <asm/arch/gpio.h> |
| #include <common.h> |
| #include <clk.h> |
| #include <dm.h> |
| #include <fdt_support.h> |
| #include <linux/err.h> |
| #include <malloc.h> |
| #include <miiphy.h> |
| #include <net.h> |
| #include <reset.h> |
| #include <dt-bindings/pinctrl/sun4i-a10.h> |
| #ifdef CONFIG_DM_GPIO |
| #include <asm-generic/gpio.h> |
| #endif |
| |
| #define MDIO_CMD_MII_BUSY BIT(0) |
| #define MDIO_CMD_MII_WRITE BIT(1) |
| |
| #define MDIO_CMD_MII_PHY_REG_ADDR_MASK 0x000001f0 |
| #define MDIO_CMD_MII_PHY_REG_ADDR_SHIFT 4 |
| #define MDIO_CMD_MII_PHY_ADDR_MASK 0x0001f000 |
| #define MDIO_CMD_MII_PHY_ADDR_SHIFT 12 |
| |
| #define CONFIG_TX_DESCR_NUM 32 |
| #define CONFIG_RX_DESCR_NUM 32 |
| #define CONFIG_ETH_BUFSIZE 2048 /* Note must be dma aligned */ |
| |
| /* |
| * The datasheet says that each descriptor can transfers up to 4096 bytes |
| * But later, the register documentation reduces that value to 2048, |
| * using 2048 cause strange behaviours and even BSP driver use 2047 |
| */ |
| #define CONFIG_ETH_RXSIZE 2044 /* Note must fit in ETH_BUFSIZE */ |
| |
| #define TX_TOTAL_BUFSIZE (CONFIG_ETH_BUFSIZE * CONFIG_TX_DESCR_NUM) |
| #define RX_TOTAL_BUFSIZE (CONFIG_ETH_BUFSIZE * CONFIG_RX_DESCR_NUM) |
| |
| #define H3_EPHY_DEFAULT_VALUE 0x58000 |
| #define H3_EPHY_DEFAULT_MASK GENMASK(31, 15) |
| #define H3_EPHY_ADDR_SHIFT 20 |
| #define REG_PHY_ADDR_MASK GENMASK(4, 0) |
| #define H3_EPHY_LED_POL BIT(17) /* 1: active low, 0: active high */ |
| #define H3_EPHY_SHUTDOWN BIT(16) /* 1: shutdown, 0: power up */ |
| #define H3_EPHY_SELECT BIT(15) /* 1: internal PHY, 0: external PHY */ |
| |
| #define SC_RMII_EN BIT(13) |
| #define SC_EPIT BIT(2) /* 1: RGMII, 0: MII */ |
| #define SC_ETCS_MASK GENMASK(1, 0) |
| #define SC_ETCS_EXT_GMII 0x1 |
| #define SC_ETCS_INT_GMII 0x2 |
| #define SC_ETXDC_MASK GENMASK(12, 10) |
| #define SC_ETXDC_OFFSET 10 |
| #define SC_ERXDC_MASK GENMASK(9, 5) |
| #define SC_ERXDC_OFFSET 5 |
| |
| #define CONFIG_MDIO_TIMEOUT (3 * CONFIG_SYS_HZ) |
| |
| #define AHB_GATE_OFFSET_EPHY 0 |
| |
| /* IO mux settings */ |
| #define SUN8I_IOMUX_H3 2 |
| #define SUN8I_IOMUX_R40 5 |
| #define SUN8I_IOMUX 4 |
| |
| /* H3/A64 EMAC Register's offset */ |
| #define EMAC_CTL0 0x00 |
| #define EMAC_CTL1 0x04 |
| #define EMAC_INT_STA 0x08 |
| #define EMAC_INT_EN 0x0c |
| #define EMAC_TX_CTL0 0x10 |
| #define EMAC_TX_CTL1 0x14 |
| #define EMAC_TX_FLOW_CTL 0x1c |
| #define EMAC_TX_DMA_DESC 0x20 |
| #define EMAC_RX_CTL0 0x24 |
| #define EMAC_RX_CTL1 0x28 |
| #define EMAC_RX_DMA_DESC 0x34 |
| #define EMAC_MII_CMD 0x48 |
| #define EMAC_MII_DATA 0x4c |
| #define EMAC_ADDR0_HIGH 0x50 |
| #define EMAC_ADDR0_LOW 0x54 |
| #define EMAC_TX_DMA_STA 0xb0 |
| #define EMAC_TX_CUR_DESC 0xb4 |
| #define EMAC_TX_CUR_BUF 0xb8 |
| #define EMAC_RX_DMA_STA 0xc0 |
| #define EMAC_RX_CUR_DESC 0xc4 |
| |
| DECLARE_GLOBAL_DATA_PTR; |
| |
| enum emac_variant { |
| A83T_EMAC = 1, |
| H3_EMAC, |
| A64_EMAC, |
| R40_GMAC, |
| }; |
| |
| struct emac_dma_desc { |
| u32 status; |
| u32 st; |
| u32 buf_addr; |
| u32 next; |
| } __aligned(ARCH_DMA_MINALIGN); |
| |
| struct emac_eth_dev { |
| struct emac_dma_desc rx_chain[CONFIG_TX_DESCR_NUM]; |
| struct emac_dma_desc tx_chain[CONFIG_RX_DESCR_NUM]; |
| char rxbuffer[RX_TOTAL_BUFSIZE] __aligned(ARCH_DMA_MINALIGN); |
| char txbuffer[TX_TOTAL_BUFSIZE] __aligned(ARCH_DMA_MINALIGN); |
| |
| u32 interface; |
| u32 phyaddr; |
| u32 link; |
| u32 speed; |
| u32 duplex; |
| u32 phy_configured; |
| u32 tx_currdescnum; |
| u32 rx_currdescnum; |
| u32 addr; |
| u32 tx_slot; |
| bool use_internal_phy; |
| |
| enum emac_variant variant; |
| void *mac_reg; |
| phys_addr_t sysctl_reg; |
| struct phy_device *phydev; |
| struct mii_dev *bus; |
| struct clk tx_clk; |
| struct clk ephy_clk; |
| struct reset_ctl tx_rst; |
| struct reset_ctl ephy_rst; |
| #ifdef CONFIG_DM_GPIO |
| struct gpio_desc reset_gpio; |
| #endif |
| }; |
| |
| |
| struct sun8i_eth_pdata { |
| struct eth_pdata eth_pdata; |
| u32 reset_delays[3]; |
| int tx_delay_ps; |
| int rx_delay_ps; |
| }; |
| |
| |
| static int sun8i_mdio_read(struct mii_dev *bus, int addr, int devad, int reg) |
| { |
| struct udevice *dev = bus->priv; |
| struct emac_eth_dev *priv = dev_get_priv(dev); |
| ulong start; |
| u32 miiaddr = 0; |
| int timeout = CONFIG_MDIO_TIMEOUT; |
| |
| miiaddr &= ~MDIO_CMD_MII_WRITE; |
| miiaddr &= ~MDIO_CMD_MII_PHY_REG_ADDR_MASK; |
| miiaddr |= (reg << MDIO_CMD_MII_PHY_REG_ADDR_SHIFT) & |
| MDIO_CMD_MII_PHY_REG_ADDR_MASK; |
| |
| miiaddr &= ~MDIO_CMD_MII_PHY_ADDR_MASK; |
| |
| miiaddr |= (addr << MDIO_CMD_MII_PHY_ADDR_SHIFT) & |
| MDIO_CMD_MII_PHY_ADDR_MASK; |
| |
| miiaddr |= MDIO_CMD_MII_BUSY; |
| |
| writel(miiaddr, priv->mac_reg + EMAC_MII_CMD); |
| |
| start = get_timer(0); |
| while (get_timer(start) < timeout) { |
| if (!(readl(priv->mac_reg + EMAC_MII_CMD) & MDIO_CMD_MII_BUSY)) |
| return readl(priv->mac_reg + EMAC_MII_DATA); |
| udelay(10); |
| }; |
| |
| return -1; |
| } |
| |
| static int sun8i_mdio_write(struct mii_dev *bus, int addr, int devad, int reg, |
| u16 val) |
| { |
| struct udevice *dev = bus->priv; |
| struct emac_eth_dev *priv = dev_get_priv(dev); |
| ulong start; |
| u32 miiaddr = 0; |
| int ret = -1, timeout = CONFIG_MDIO_TIMEOUT; |
| |
| miiaddr &= ~MDIO_CMD_MII_PHY_REG_ADDR_MASK; |
| miiaddr |= (reg << MDIO_CMD_MII_PHY_REG_ADDR_SHIFT) & |
| MDIO_CMD_MII_PHY_REG_ADDR_MASK; |
| |
| miiaddr &= ~MDIO_CMD_MII_PHY_ADDR_MASK; |
| miiaddr |= (addr << MDIO_CMD_MII_PHY_ADDR_SHIFT) & |
| MDIO_CMD_MII_PHY_ADDR_MASK; |
| |
| miiaddr |= MDIO_CMD_MII_WRITE; |
| miiaddr |= MDIO_CMD_MII_BUSY; |
| |
| writel(val, priv->mac_reg + EMAC_MII_DATA); |
| writel(miiaddr, priv->mac_reg + EMAC_MII_CMD); |
| |
| start = get_timer(0); |
| while (get_timer(start) < timeout) { |
| if (!(readl(priv->mac_reg + EMAC_MII_CMD) & |
| MDIO_CMD_MII_BUSY)) { |
| ret = 0; |
| break; |
| } |
| udelay(10); |
| }; |
| |
| return ret; |
| } |
| |
| static int _sun8i_write_hwaddr(struct emac_eth_dev *priv, u8 *mac_id) |
| { |
| u32 macid_lo, macid_hi; |
| |
| macid_lo = mac_id[0] + (mac_id[1] << 8) + (mac_id[2] << 16) + |
| (mac_id[3] << 24); |
| macid_hi = mac_id[4] + (mac_id[5] << 8); |
| |
| writel(macid_hi, priv->mac_reg + EMAC_ADDR0_HIGH); |
| writel(macid_lo, priv->mac_reg + EMAC_ADDR0_LOW); |
| |
| return 0; |
| } |
| |
| static void sun8i_adjust_link(struct emac_eth_dev *priv, |
| struct phy_device *phydev) |
| { |
| u32 v; |
| |
| v = readl(priv->mac_reg + EMAC_CTL0); |
| |
| if (phydev->duplex) |
| v |= BIT(0); |
| else |
| v &= ~BIT(0); |
| |
| v &= ~0x0C; |
| |
| switch (phydev->speed) { |
| case 1000: |
| break; |
| case 100: |
| v |= BIT(2); |
| v |= BIT(3); |
| break; |
| case 10: |
| v |= BIT(3); |
| break; |
| } |
| writel(v, priv->mac_reg + EMAC_CTL0); |
| } |
| |
| static int sun8i_emac_set_syscon_ephy(struct emac_eth_dev *priv, u32 *reg) |
| { |
| if (priv->use_internal_phy) { |
| /* H3 based SoC's that has an Internal 100MBit PHY |
| * needs to be configured and powered up before use |
| */ |
| *reg &= ~H3_EPHY_DEFAULT_MASK; |
| *reg |= H3_EPHY_DEFAULT_VALUE; |
| *reg |= priv->phyaddr << H3_EPHY_ADDR_SHIFT; |
| *reg &= ~H3_EPHY_SHUTDOWN; |
| *reg |= H3_EPHY_SELECT; |
| } else |
| /* This is to select External Gigabit PHY on |
| * the boards with H3 SoC. |
| */ |
| *reg &= ~H3_EPHY_SELECT; |
| |
| return 0; |
| } |
| |
| static int sun8i_emac_set_syscon(struct sun8i_eth_pdata *pdata, |
| struct emac_eth_dev *priv) |
| { |
| int ret; |
| u32 reg; |
| |
| if (priv->variant == R40_GMAC) { |
| /* Select RGMII for R40 */ |
| reg = readl(priv->sysctl_reg + 0x164); |
| reg |= CCM_GMAC_CTRL_TX_CLK_SRC_INT_RGMII | |
| CCM_GMAC_CTRL_GPIT_RGMII | |
| CCM_GMAC_CTRL_TX_CLK_DELAY(CONFIG_GMAC_TX_DELAY); |
| |
| writel(reg, priv->sysctl_reg + 0x164); |
| return 0; |
| } |
| |
| reg = readl(priv->sysctl_reg + 0x30); |
| |
| if (priv->variant == H3_EMAC) { |
| ret = sun8i_emac_set_syscon_ephy(priv, ®); |
| if (ret) |
| return ret; |
| } |
| |
| reg &= ~(SC_ETCS_MASK | SC_EPIT); |
| if (priv->variant == H3_EMAC || priv->variant == A64_EMAC) |
| reg &= ~SC_RMII_EN; |
| |
| switch (priv->interface) { |
| case PHY_INTERFACE_MODE_MII: |
| /* default */ |
| break; |
| case PHY_INTERFACE_MODE_RGMII: |
| reg |= SC_EPIT | SC_ETCS_INT_GMII; |
| break; |
| case PHY_INTERFACE_MODE_RMII: |
| if (priv->variant == H3_EMAC || |
| priv->variant == A64_EMAC) { |
| reg |= SC_RMII_EN | SC_ETCS_EXT_GMII; |
| break; |
| } |
| /* RMII not supported on A83T */ |
| default: |
| debug("%s: Invalid PHY interface\n", __func__); |
| return -EINVAL; |
| } |
| |
| if (pdata->tx_delay_ps) |
| reg |= ((pdata->tx_delay_ps / 100) << SC_ETXDC_OFFSET) |
| & SC_ETXDC_MASK; |
| |
| if (pdata->rx_delay_ps) |
| reg |= ((pdata->rx_delay_ps / 100) << SC_ERXDC_OFFSET) |
| & SC_ERXDC_MASK; |
| |
| writel(reg, priv->sysctl_reg + 0x30); |
| |
| return 0; |
| } |
| |
| static int sun8i_phy_init(struct emac_eth_dev *priv, void *dev) |
| { |
| struct phy_device *phydev; |
| |
| phydev = phy_connect(priv->bus, priv->phyaddr, dev, priv->interface); |
| if (!phydev) |
| return -ENODEV; |
| |
| phy_connect_dev(phydev, dev); |
| |
| priv->phydev = phydev; |
| phy_config(priv->phydev); |
| |
| return 0; |
| } |
| |
| static void rx_descs_init(struct emac_eth_dev *priv) |
| { |
| struct emac_dma_desc *desc_table_p = &priv->rx_chain[0]; |
| char *rxbuffs = &priv->rxbuffer[0]; |
| struct emac_dma_desc *desc_p; |
| u32 idx; |
| |
| /* flush Rx buffers */ |
| flush_dcache_range((uintptr_t)rxbuffs, (ulong)rxbuffs + |
| RX_TOTAL_BUFSIZE); |
| |
| for (idx = 0; idx < CONFIG_RX_DESCR_NUM; idx++) { |
| desc_p = &desc_table_p[idx]; |
| desc_p->buf_addr = (uintptr_t)&rxbuffs[idx * CONFIG_ETH_BUFSIZE] |
| ; |
| desc_p->next = (uintptr_t)&desc_table_p[idx + 1]; |
| desc_p->st |= CONFIG_ETH_RXSIZE; |
| desc_p->status = BIT(31); |
| } |
| |
| /* Correcting the last pointer of the chain */ |
| desc_p->next = (uintptr_t)&desc_table_p[0]; |
| |
| flush_dcache_range((uintptr_t)priv->rx_chain, |
| (uintptr_t)priv->rx_chain + |
| sizeof(priv->rx_chain)); |
| |
| writel((uintptr_t)&desc_table_p[0], (priv->mac_reg + EMAC_RX_DMA_DESC)); |
| priv->rx_currdescnum = 0; |
| } |
| |
| static void tx_descs_init(struct emac_eth_dev *priv) |
| { |
| struct emac_dma_desc *desc_table_p = &priv->tx_chain[0]; |
| char *txbuffs = &priv->txbuffer[0]; |
| struct emac_dma_desc *desc_p; |
| u32 idx; |
| |
| for (idx = 0; idx < CONFIG_TX_DESCR_NUM; idx++) { |
| desc_p = &desc_table_p[idx]; |
| desc_p->buf_addr = (uintptr_t)&txbuffs[idx * CONFIG_ETH_BUFSIZE] |
| ; |
| desc_p->next = (uintptr_t)&desc_table_p[idx + 1]; |
| desc_p->status = (1 << 31); |
| desc_p->st = 0; |
| } |
| |
| /* Correcting the last pointer of the chain */ |
| desc_p->next = (uintptr_t)&desc_table_p[0]; |
| |
| /* Flush all Tx buffer descriptors */ |
| flush_dcache_range((uintptr_t)priv->tx_chain, |
| (uintptr_t)priv->tx_chain + |
| sizeof(priv->tx_chain)); |
| |
| writel((uintptr_t)&desc_table_p[0], priv->mac_reg + EMAC_TX_DMA_DESC); |
| priv->tx_currdescnum = 0; |
| } |
| |
| static int _sun8i_emac_eth_init(struct emac_eth_dev *priv, u8 *enetaddr) |
| { |
| u32 reg, v; |
| int timeout = 100; |
| |
| reg = readl((priv->mac_reg + EMAC_CTL1)); |
| |
| if (!(reg & 0x1)) { |
| /* Soft reset MAC */ |
| setbits_le32((priv->mac_reg + EMAC_CTL1), 0x1); |
| do { |
| reg = readl(priv->mac_reg + EMAC_CTL1); |
| } while ((reg & 0x01) != 0 && (--timeout)); |
| if (!timeout) { |
| printf("%s: Timeout\n", __func__); |
| return -1; |
| } |
| } |
| |
| /* Rewrite mac address after reset */ |
| _sun8i_write_hwaddr(priv, enetaddr); |
| |
| v = readl(priv->mac_reg + EMAC_TX_CTL1); |
| /* TX_MD Transmission starts after a full frame located in TX DMA FIFO*/ |
| v |= BIT(1); |
| writel(v, priv->mac_reg + EMAC_TX_CTL1); |
| |
| v = readl(priv->mac_reg + EMAC_RX_CTL1); |
| /* RX_MD RX DMA reads data from RX DMA FIFO to host memory after a |
| * complete frame has been written to RX DMA FIFO |
| */ |
| v |= BIT(1); |
| writel(v, priv->mac_reg + EMAC_RX_CTL1); |
| |
| /* DMA */ |
| writel(8 << 24, priv->mac_reg + EMAC_CTL1); |
| |
| /* Initialize rx/tx descriptors */ |
| rx_descs_init(priv); |
| tx_descs_init(priv); |
| |
| /* PHY Start Up */ |
| phy_startup(priv->phydev); |
| |
| sun8i_adjust_link(priv, priv->phydev); |
| |
| /* Start RX DMA */ |
| v = readl(priv->mac_reg + EMAC_RX_CTL1); |
| v |= BIT(30); |
| writel(v, priv->mac_reg + EMAC_RX_CTL1); |
| /* Start TX DMA */ |
| v = readl(priv->mac_reg + EMAC_TX_CTL1); |
| v |= BIT(30); |
| writel(v, priv->mac_reg + EMAC_TX_CTL1); |
| |
| /* Enable RX/TX */ |
| setbits_le32(priv->mac_reg + EMAC_RX_CTL0, BIT(31)); |
| setbits_le32(priv->mac_reg + EMAC_TX_CTL0, BIT(31)); |
| |
| return 0; |
| } |
| |
| static int parse_phy_pins(struct udevice *dev) |
| { |
| struct emac_eth_dev *priv = dev_get_priv(dev); |
| int offset; |
| const char *pin_name; |
| int drive, pull = SUN4I_PINCTRL_NO_PULL, i; |
| |
| offset = fdtdec_lookup_phandle(gd->fdt_blob, dev_of_offset(dev), |
| "pinctrl-0"); |
| if (offset < 0) { |
| printf("WARNING: emac: cannot find pinctrl-0 node\n"); |
| return offset; |
| } |
| |
| drive = fdt_getprop_u32_default_node(gd->fdt_blob, offset, 0, |
| "drive-strength", ~0); |
| if (drive != ~0) { |
| if (drive <= 10) |
| drive = SUN4I_PINCTRL_10_MA; |
| else if (drive <= 20) |
| drive = SUN4I_PINCTRL_20_MA; |
| else if (drive <= 30) |
| drive = SUN4I_PINCTRL_30_MA; |
| else |
| drive = SUN4I_PINCTRL_40_MA; |
| } |
| |
| if (fdt_get_property(gd->fdt_blob, offset, "bias-pull-up", NULL)) |
| pull = SUN4I_PINCTRL_PULL_UP; |
| else if (fdt_get_property(gd->fdt_blob, offset, "bias-pull-down", NULL)) |
| pull = SUN4I_PINCTRL_PULL_DOWN; |
| |
| for (i = 0; ; i++) { |
| int pin; |
| |
| pin_name = fdt_stringlist_get(gd->fdt_blob, offset, |
| "pins", i, NULL); |
| if (!pin_name) |
| break; |
| |
| pin = sunxi_name_to_gpio(pin_name); |
| if (pin < 0) |
| continue; |
| |
| if (priv->variant == H3_EMAC) |
| sunxi_gpio_set_cfgpin(pin, SUN8I_IOMUX_H3); |
| else if (priv->variant == R40_GMAC) |
| sunxi_gpio_set_cfgpin(pin, SUN8I_IOMUX_R40); |
| else |
| sunxi_gpio_set_cfgpin(pin, SUN8I_IOMUX); |
| |
| if (drive != ~0) |
| sunxi_gpio_set_drv(pin, drive); |
| if (pull != ~0) |
| sunxi_gpio_set_pull(pin, pull); |
| } |
| |
| if (!i) { |
| printf("WARNING: emac: cannot find pins property\n"); |
| return -2; |
| } |
| |
| return 0; |
| } |
| |
| static int _sun8i_eth_recv(struct emac_eth_dev *priv, uchar **packetp) |
| { |
| u32 status, desc_num = priv->rx_currdescnum; |
| struct emac_dma_desc *desc_p = &priv->rx_chain[desc_num]; |
| int length = -EAGAIN; |
| int good_packet = 1; |
| uintptr_t desc_start = (uintptr_t)desc_p; |
| uintptr_t desc_end = desc_start + |
| roundup(sizeof(*desc_p), ARCH_DMA_MINALIGN); |
| |
| ulong data_start = (uintptr_t)desc_p->buf_addr; |
| ulong data_end; |
| |
| /* Invalidate entire buffer descriptor */ |
| invalidate_dcache_range(desc_start, desc_end); |
| |
| status = desc_p->status; |
| |
| /* Check for DMA own bit */ |
| if (!(status & BIT(31))) { |
| length = (desc_p->status >> 16) & 0x3FFF; |
| |
| if (length < 0x40) { |
| good_packet = 0; |
| debug("RX: Bad Packet (runt)\n"); |
| } |
| |
| data_end = data_start + length; |
| /* Invalidate received data */ |
| invalidate_dcache_range(rounddown(data_start, |
| ARCH_DMA_MINALIGN), |
| roundup(data_end, |
| ARCH_DMA_MINALIGN)); |
| if (good_packet) { |
| if (length > CONFIG_ETH_RXSIZE) { |
| printf("Received packet is too big (len=%d)\n", |
| length); |
| return -EMSGSIZE; |
| } |
| *packetp = (uchar *)(ulong)desc_p->buf_addr; |
| return length; |
| } |
| } |
| |
| return length; |
| } |
| |
| static int _sun8i_emac_eth_send(struct emac_eth_dev *priv, void *packet, |
| int len) |
| { |
| u32 v, desc_num = priv->tx_currdescnum; |
| struct emac_dma_desc *desc_p = &priv->tx_chain[desc_num]; |
| uintptr_t desc_start = (uintptr_t)desc_p; |
| uintptr_t desc_end = desc_start + |
| roundup(sizeof(*desc_p), ARCH_DMA_MINALIGN); |
| |
| uintptr_t data_start = (uintptr_t)desc_p->buf_addr; |
| uintptr_t data_end = data_start + |
| roundup(len, ARCH_DMA_MINALIGN); |
| |
| /* Invalidate entire buffer descriptor */ |
| invalidate_dcache_range(desc_start, desc_end); |
| |
| desc_p->st = len; |
| /* Mandatory undocumented bit */ |
| desc_p->st |= BIT(24); |
| |
| memcpy((void *)data_start, packet, len); |
| |
| /* Flush data to be sent */ |
| flush_dcache_range(data_start, data_end); |
| |
| /* frame end */ |
| desc_p->st |= BIT(30); |
| desc_p->st |= BIT(31); |
| |
| /*frame begin */ |
| desc_p->st |= BIT(29); |
| desc_p->status = BIT(31); |
| |
| /*Descriptors st and status field has changed, so FLUSH it */ |
| flush_dcache_range(desc_start, desc_end); |
| |
| /* Move to next Descriptor and wrap around */ |
| if (++desc_num >= CONFIG_TX_DESCR_NUM) |
| desc_num = 0; |
| priv->tx_currdescnum = desc_num; |
| |
| /* Start the DMA */ |
| v = readl(priv->mac_reg + EMAC_TX_CTL1); |
| v |= BIT(31);/* mandatory */ |
| v |= BIT(30);/* mandatory */ |
| writel(v, priv->mac_reg + EMAC_TX_CTL1); |
| |
| return 0; |
| } |
| |
| static int sun8i_eth_write_hwaddr(struct udevice *dev) |
| { |
| struct eth_pdata *pdata = dev_get_platdata(dev); |
| struct emac_eth_dev *priv = dev_get_priv(dev); |
| |
| return _sun8i_write_hwaddr(priv, pdata->enetaddr); |
| } |
| |
| static int sun8i_emac_board_setup(struct emac_eth_dev *priv) |
| { |
| int ret; |
| |
| ret = clk_enable(&priv->tx_clk); |
| if (ret) { |
| dev_err(dev, "failed to enable TX clock\n"); |
| return ret; |
| } |
| |
| if (reset_valid(&priv->tx_rst)) { |
| ret = reset_deassert(&priv->tx_rst); |
| if (ret) { |
| dev_err(dev, "failed to deassert TX reset\n"); |
| goto err_tx_clk; |
| } |
| } |
| |
| /* Only H3/H5 have clock controls for internal EPHY */ |
| if (clk_valid(&priv->ephy_clk)) { |
| ret = clk_enable(&priv->ephy_clk); |
| if (ret) { |
| dev_err(dev, "failed to enable EPHY TX clock\n"); |
| return ret; |
| } |
| } |
| |
| if (reset_valid(&priv->ephy_rst)) { |
| ret = reset_deassert(&priv->ephy_rst); |
| if (ret) { |
| dev_err(dev, "failed to deassert EPHY TX clock\n"); |
| return ret; |
| } |
| } |
| |
| return 0; |
| |
| err_tx_clk: |
| clk_disable(&priv->tx_clk); |
| return ret; |
| } |
| |
| #if defined(CONFIG_DM_GPIO) |
| static int sun8i_mdio_reset(struct mii_dev *bus) |
| { |
| struct udevice *dev = bus->priv; |
| struct emac_eth_dev *priv = dev_get_priv(dev); |
| struct sun8i_eth_pdata *pdata = dev_get_platdata(dev); |
| int ret; |
| |
| if (!dm_gpio_is_valid(&priv->reset_gpio)) |
| return 0; |
| |
| /* reset the phy */ |
| ret = dm_gpio_set_value(&priv->reset_gpio, 0); |
| if (ret) |
| return ret; |
| |
| udelay(pdata->reset_delays[0]); |
| |
| ret = dm_gpio_set_value(&priv->reset_gpio, 1); |
| if (ret) |
| return ret; |
| |
| udelay(pdata->reset_delays[1]); |
| |
| ret = dm_gpio_set_value(&priv->reset_gpio, 0); |
| if (ret) |
| return ret; |
| |
| udelay(pdata->reset_delays[2]); |
| |
| return 0; |
| } |
| #endif |
| |
| static int sun8i_mdio_init(const char *name, struct udevice *priv) |
| { |
| struct mii_dev *bus = mdio_alloc(); |
| |
| if (!bus) { |
| debug("Failed to allocate MDIO bus\n"); |
| return -ENOMEM; |
| } |
| |
| bus->read = sun8i_mdio_read; |
| bus->write = sun8i_mdio_write; |
| snprintf(bus->name, sizeof(bus->name), name); |
| bus->priv = (void *)priv; |
| #if defined(CONFIG_DM_GPIO) |
| bus->reset = sun8i_mdio_reset; |
| #endif |
| |
| return mdio_register(bus); |
| } |
| |
| static int sun8i_emac_eth_start(struct udevice *dev) |
| { |
| struct eth_pdata *pdata = dev_get_platdata(dev); |
| |
| return _sun8i_emac_eth_init(dev->priv, pdata->enetaddr); |
| } |
| |
| static int sun8i_emac_eth_send(struct udevice *dev, void *packet, int length) |
| { |
| struct emac_eth_dev *priv = dev_get_priv(dev); |
| |
| return _sun8i_emac_eth_send(priv, packet, length); |
| } |
| |
| static int sun8i_emac_eth_recv(struct udevice *dev, int flags, uchar **packetp) |
| { |
| struct emac_eth_dev *priv = dev_get_priv(dev); |
| |
| return _sun8i_eth_recv(priv, packetp); |
| } |
| |
| static int _sun8i_free_pkt(struct emac_eth_dev *priv) |
| { |
| u32 desc_num = priv->rx_currdescnum; |
| struct emac_dma_desc *desc_p = &priv->rx_chain[desc_num]; |
| uintptr_t desc_start = (uintptr_t)desc_p; |
| uintptr_t desc_end = desc_start + |
| roundup(sizeof(u32), ARCH_DMA_MINALIGN); |
| |
| /* Make the current descriptor valid again */ |
| desc_p->status |= BIT(31); |
| |
| /* Flush Status field of descriptor */ |
| flush_dcache_range(desc_start, desc_end); |
| |
| /* Move to next desc and wrap-around condition. */ |
| if (++desc_num >= CONFIG_RX_DESCR_NUM) |
| desc_num = 0; |
| priv->rx_currdescnum = desc_num; |
| |
| return 0; |
| } |
| |
| static int sun8i_eth_free_pkt(struct udevice *dev, uchar *packet, |
| int length) |
| { |
| struct emac_eth_dev *priv = dev_get_priv(dev); |
| |
| return _sun8i_free_pkt(priv); |
| } |
| |
| static void sun8i_emac_eth_stop(struct udevice *dev) |
| { |
| struct emac_eth_dev *priv = dev_get_priv(dev); |
| |
| /* Stop Rx/Tx transmitter */ |
| clrbits_le32(priv->mac_reg + EMAC_RX_CTL0, BIT(31)); |
| clrbits_le32(priv->mac_reg + EMAC_TX_CTL0, BIT(31)); |
| |
| /* Stop TX DMA */ |
| clrbits_le32(priv->mac_reg + EMAC_TX_CTL1, BIT(30)); |
| |
| phy_shutdown(priv->phydev); |
| } |
| |
| static int sun8i_emac_eth_probe(struct udevice *dev) |
| { |
| struct sun8i_eth_pdata *sun8i_pdata = dev_get_platdata(dev); |
| struct eth_pdata *pdata = &sun8i_pdata->eth_pdata; |
| struct emac_eth_dev *priv = dev_get_priv(dev); |
| int ret; |
| |
| priv->mac_reg = (void *)pdata->iobase; |
| |
| ret = sun8i_emac_board_setup(priv); |
| if (ret) |
| return ret; |
| |
| sun8i_emac_set_syscon(sun8i_pdata, priv); |
| |
| sun8i_mdio_init(dev->name, dev); |
| priv->bus = miiphy_get_dev_by_name(dev->name); |
| |
| return sun8i_phy_init(priv, dev); |
| } |
| |
| static const struct eth_ops sun8i_emac_eth_ops = { |
| .start = sun8i_emac_eth_start, |
| .write_hwaddr = sun8i_eth_write_hwaddr, |
| .send = sun8i_emac_eth_send, |
| .recv = sun8i_emac_eth_recv, |
| .free_pkt = sun8i_eth_free_pkt, |
| .stop = sun8i_emac_eth_stop, |
| }; |
| |
| static int sun8i_get_ephy_nodes(struct emac_eth_dev *priv) |
| { |
| int emac_node, ephy_node, ret, ephy_handle; |
| |
| emac_node = fdt_path_offset(gd->fdt_blob, |
| "/soc/ethernet@1c30000"); |
| if (emac_node < 0) { |
| debug("failed to get emac node\n"); |
| return emac_node; |
| } |
| ephy_handle = fdtdec_lookup_phandle(gd->fdt_blob, |
| emac_node, "phy-handle"); |
| |
| /* look for mdio-mux node for internal PHY node */ |
| ephy_node = fdt_path_offset(gd->fdt_blob, |
| "/soc/ethernet@1c30000/mdio-mux/mdio@1/ethernet-phy@1"); |
| if (ephy_node < 0) { |
| debug("failed to get mdio-mux with internal PHY\n"); |
| return ephy_node; |
| } |
| |
| /* This is not the phy we are looking for */ |
| if (ephy_node != ephy_handle) |
| return 0; |
| |
| ret = fdt_node_check_compatible(gd->fdt_blob, ephy_node, |
| "allwinner,sun8i-h3-mdio-internal"); |
| if (ret < 0) { |
| debug("failed to find mdio-internal node\n"); |
| return ret; |
| } |
| |
| ret = clk_get_by_index_nodev(offset_to_ofnode(ephy_node), 0, |
| &priv->ephy_clk); |
| if (ret) { |
| dev_err(dev, "failed to get EPHY TX clock\n"); |
| return ret; |
| } |
| |
| ret = reset_get_by_index_nodev(offset_to_ofnode(ephy_node), 0, |
| &priv->ephy_rst); |
| if (ret) { |
| dev_err(dev, "failed to get EPHY TX reset\n"); |
| return ret; |
| } |
| |
| priv->use_internal_phy = true; |
| |
| return 0; |
| } |
| |
| static int sun8i_emac_eth_ofdata_to_platdata(struct udevice *dev) |
| { |
| struct sun8i_eth_pdata *sun8i_pdata = dev_get_platdata(dev); |
| struct eth_pdata *pdata = &sun8i_pdata->eth_pdata; |
| struct emac_eth_dev *priv = dev_get_priv(dev); |
| const char *phy_mode; |
| const fdt32_t *reg; |
| int node = dev_of_offset(dev); |
| int offset = 0; |
| #ifdef CONFIG_DM_GPIO |
| int reset_flags = GPIOD_IS_OUT; |
| #endif |
| int ret; |
| |
| pdata->iobase = devfdt_get_addr(dev); |
| if (pdata->iobase == FDT_ADDR_T_NONE) { |
| debug("%s: Cannot find MAC base address\n", __func__); |
| return -EINVAL; |
| } |
| |
| priv->variant = dev_get_driver_data(dev); |
| |
| if (!priv->variant) { |
| printf("%s: Missing variant\n", __func__); |
| return -EINVAL; |
| } |
| |
| ret = clk_get_by_name(dev, "stmmaceth", &priv->tx_clk); |
| if (ret) { |
| dev_err(dev, "failed to get TX clock\n"); |
| return ret; |
| } |
| |
| ret = reset_get_by_name(dev, "stmmaceth", &priv->tx_rst); |
| if (ret && ret != -ENOENT) { |
| dev_err(dev, "failed to get TX reset\n"); |
| return ret; |
| } |
| |
| offset = fdtdec_lookup_phandle(gd->fdt_blob, node, "syscon"); |
| if (offset < 0) { |
| debug("%s: cannot find syscon node\n", __func__); |
| return -EINVAL; |
| } |
| |
| reg = fdt_getprop(gd->fdt_blob, offset, "reg", NULL); |
| if (!reg) { |
| debug("%s: cannot find reg property in syscon node\n", |
| __func__); |
| return -EINVAL; |
| } |
| priv->sysctl_reg = fdt_translate_address((void *)gd->fdt_blob, |
| offset, reg); |
| if (priv->sysctl_reg == FDT_ADDR_T_NONE) { |
| debug("%s: Cannot find syscon base address\n", __func__); |
| return -EINVAL; |
| } |
| |
| pdata->phy_interface = -1; |
| priv->phyaddr = -1; |
| priv->use_internal_phy = false; |
| |
| offset = fdtdec_lookup_phandle(gd->fdt_blob, node, "phy-handle"); |
| if (offset < 0) { |
| debug("%s: Cannot find PHY address\n", __func__); |
| return -EINVAL; |
| } |
| priv->phyaddr = fdtdec_get_int(gd->fdt_blob, offset, "reg", -1); |
| |
| phy_mode = fdt_getprop(gd->fdt_blob, node, "phy-mode", NULL); |
| |
| if (phy_mode) |
| pdata->phy_interface = phy_get_interface_by_name(phy_mode); |
| printf("phy interface%d\n", pdata->phy_interface); |
| |
| if (pdata->phy_interface == -1) { |
| debug("%s: Invalid PHY interface '%s'\n", __func__, phy_mode); |
| return -EINVAL; |
| } |
| |
| if (priv->variant == H3_EMAC) { |
| ret = sun8i_get_ephy_nodes(priv); |
| if (ret) |
| return ret; |
| } |
| |
| priv->interface = pdata->phy_interface; |
| |
| if (!priv->use_internal_phy) |
| parse_phy_pins(dev); |
| |
| sun8i_pdata->tx_delay_ps = fdtdec_get_int(gd->fdt_blob, node, |
| "allwinner,tx-delay-ps", 0); |
| if (sun8i_pdata->tx_delay_ps < 0 || sun8i_pdata->tx_delay_ps > 700) |
| printf("%s: Invalid TX delay value %d\n", __func__, |
| sun8i_pdata->tx_delay_ps); |
| |
| sun8i_pdata->rx_delay_ps = fdtdec_get_int(gd->fdt_blob, node, |
| "allwinner,rx-delay-ps", 0); |
| if (sun8i_pdata->rx_delay_ps < 0 || sun8i_pdata->rx_delay_ps > 3100) |
| printf("%s: Invalid RX delay value %d\n", __func__, |
| sun8i_pdata->rx_delay_ps); |
| |
| #ifdef CONFIG_DM_GPIO |
| if (fdtdec_get_bool(gd->fdt_blob, dev_of_offset(dev), |
| "snps,reset-active-low")) |
| reset_flags |= GPIOD_ACTIVE_LOW; |
| |
| ret = gpio_request_by_name(dev, "snps,reset-gpio", 0, |
| &priv->reset_gpio, reset_flags); |
| |
| if (ret == 0) { |
| ret = fdtdec_get_int_array(gd->fdt_blob, dev_of_offset(dev), |
| "snps,reset-delays-us", |
| sun8i_pdata->reset_delays, 3); |
| } else if (ret == -ENOENT) { |
| ret = 0; |
| } |
| #endif |
| |
| return 0; |
| } |
| |
| static const struct udevice_id sun8i_emac_eth_ids[] = { |
| {.compatible = "allwinner,sun8i-h3-emac", .data = (uintptr_t)H3_EMAC }, |
| {.compatible = "allwinner,sun50i-a64-emac", |
| .data = (uintptr_t)A64_EMAC }, |
| {.compatible = "allwinner,sun8i-a83t-emac", |
| .data = (uintptr_t)A83T_EMAC }, |
| {.compatible = "allwinner,sun8i-r40-gmac", |
| .data = (uintptr_t)R40_GMAC }, |
| { } |
| }; |
| |
| U_BOOT_DRIVER(eth_sun8i_emac) = { |
| .name = "eth_sun8i_emac", |
| .id = UCLASS_ETH, |
| .of_match = sun8i_emac_eth_ids, |
| .ofdata_to_platdata = sun8i_emac_eth_ofdata_to_platdata, |
| .probe = sun8i_emac_eth_probe, |
| .ops = &sun8i_emac_eth_ops, |
| .priv_auto_alloc_size = sizeof(struct emac_eth_dev), |
| .platdata_auto_alloc_size = sizeof(struct sun8i_eth_pdata), |
| .flags = DM_FLAG_ALLOC_PRIV_DMA, |
| }; |