| /* SPDX-License-Identifier: GPL-2.0+ */ |
| /* |
| * Copyright 2017-2018 NXP |
| */ |
| |
| #ifndef __LS1088_COMMON_H |
| #define __LS1088_COMMON_H |
| |
| /* SPL build */ |
| #ifdef CONFIG_SPL_BUILD |
| #define SPL_NO_BOARDINFO |
| #define SPL_NO_QIXIS |
| #define SPL_NO_PCI |
| #define SPL_NO_ENV |
| #define SPL_NO_RTC |
| #define SPL_NO_USB |
| #define SPL_NO_SATA |
| #define SPL_NO_QSPI |
| #define SPL_NO_IFC |
| #endif |
| |
| #include <asm/arch/stream_id_lsch3.h> |
| #include <asm/arch/config.h> |
| #include <asm/arch/soc.h> |
| |
| #define LS1088ARDB_PB_BOARD 0x4A |
| /* Link Definitions */ |
| |
| /* Link Definitions */ |
| #define CONFIG_SYS_FSL_QSPI_BASE 0x20000000 |
| |
| #define CONFIG_VERY_BIG_RAM |
| #define CONFIG_SYS_DDR_SDRAM_BASE 0x80000000UL |
| #define CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY 0 |
| #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE |
| #define CONFIG_SYS_DDR_BLOCK2_BASE 0x8080000000ULL |
| #define CONFIG_SYS_FSL_DDR_MAIN_NUM_CTRLS 1 |
| /* |
| * SMP Definitinos |
| */ |
| #define CPU_RELEASE_ADDR secondary_boot_addr |
| |
| /* GPIO */ |
| |
| /* I2C */ |
| |
| |
| /* Serial Port */ |
| #define CONFIG_SYS_NS16550_SERIAL |
| #define CONFIG_SYS_NS16550_REG_SIZE 1 |
| #define CONFIG_SYS_NS16550_CLK (get_bus_freq(0) / 2) |
| |
| /* |
| * During booting, IFC is mapped at the region of 0x30000000. |
| * But this region is limited to 256MB. To accommodate NOR, promjet |
| * and FPGA. This region is divided as below: |
| * 0x30000000 - 0x37ffffff : 128MB : NOR flash |
| * 0x38000000 - 0x3BFFFFFF : 64MB : Promjet |
| * 0x3C000000 - 0x40000000 : 64MB : FPGA etc |
| * |
| * To accommodate bigger NOR flash and other devices, we will map IFC |
| * chip selects to as below: |
| * 0x5_1000_0000..0x5_1fff_ffff Memory Hole |
| * 0x5_2000_0000..0x5_3fff_ffff IFC CSx (FPGA, NAND and others 512MB) |
| * 0x5_4000_0000..0x5_7fff_ffff ASIC or others 1GB |
| * 0x5_8000_0000..0x5_bfff_ffff IFC CS0 1GB (NOR/Promjet) |
| * 0x5_C000_0000..0x5_ffff_ffff IFC CS1 1GB (NOR/Promjet) |
| * |
| * For e.g. NOR flash at CS0 will be mapped to 0x580000000 after relocation. |
| * CONFIG_SYS_FLASH_BASE has the final address (core view) |
| * CONFIG_SYS_FLASH_BASE_PHYS has the final address (IFC view) |
| * CONFIG_SYS_FLASH_BASE_PHYS_EARLY has the temporary IFC address |
| * CONFIG_SYS_TEXT_BASE is linked to 0x30000000 for booting |
| */ |
| |
| #define CONFIG_SYS_FLASH_BASE 0x580000000ULL |
| #define CONFIG_SYS_FLASH_BASE_PHYS 0x80000000 |
| #define CONFIG_SYS_FLASH_BASE_PHYS_EARLY 0x00000000 |
| |
| #define CONFIG_SYS_FLASH1_BASE_PHYS 0xC0000000 |
| #define CONFIG_SYS_FLASH1_BASE_PHYS_EARLY 0x8000000 |
| |
| #ifndef __ASSEMBLY__ |
| unsigned long long get_qixis_addr(void); |
| #endif |
| |
| #define QIXIS_BASE get_qixis_addr() |
| #define QIXIS_BASE_PHYS 0x20000000 |
| #define QIXIS_BASE_PHYS_EARLY 0xC000000 |
| |
| |
| #define CONFIG_SYS_NAND_BASE 0x530000000ULL |
| #define CONFIG_SYS_NAND_BASE_PHYS 0x30000000 |
| |
| |
| /* MC firmware */ |
| /* TODO Actual DPL max length needs to be confirmed with the MC FW team */ |
| #define CONFIG_SYS_LS_MC_DPC_MAX_LENGTH 0x20000 |
| #define CONFIG_SYS_LS_MC_DRAM_DPC_OFFSET 0x00F00000 |
| #define CONFIG_SYS_LS_MC_DPL_MAX_LENGTH 0x20000 |
| #define CONFIG_SYS_LS_MC_DRAM_DPL_OFFSET 0x00F20000 |
| #define CONFIG_SYS_LS_MC_AIOP_IMG_MAX_LENGTH 0x200000 |
| #define CONFIG_SYS_LS_MC_DRAM_AIOP_IMG_OFFSET 0x07000000 |
| |
| /* |
| * Carve out a DDR region which will not be used by u-boot/Linux |
| * |
| * It will be used by MC and Debug Server. The MC region must be |
| * 512MB aligned, so the min size to hide is 512MB. |
| */ |
| |
| #if defined(CONFIG_FSL_MC_ENET) |
| #define CONFIG_SYS_LS_MC_DRAM_BLOCK_MIN_SIZE (128UL * 1024 * 1024) |
| #endif |
| |
| /* Miscellaneous configurable options */ |
| |
| /* Physical Memory Map */ |
| |
| #define CONFIG_HWCONFIG |
| #define HWCONFIG_BUFFER_SIZE 128 |
| |
| #ifndef SPL_NO_ENV |
| /* Initial environment variables */ |
| #define CONFIG_EXTRA_ENV_SETTINGS \ |
| "hwconfig=fsl_ddr:bank_intlv=auto\0" \ |
| "loadaddr=0x80100000\0" \ |
| "kernel_addr=0x100000\0" \ |
| "ramdisk_addr=0x800000\0" \ |
| "ramdisk_size=0x2000000\0" \ |
| "fdt_high=0xa0000000\0" \ |
| "initrd_high=0xffffffffffffffff\0" \ |
| "kernel_start=0x581000000\0" \ |
| "kernel_load=0xa0000000\0" \ |
| "kernel_size=0x2800000\0" \ |
| "console=ttyAMA0,38400n8\0" \ |
| "mcinitcmd=fsl_mc start mc 0x580a00000" \ |
| " 0x580e00000 \0" |
| #endif |
| |
| #ifdef CONFIG_SPL |
| #ifdef CONFIG_NXP_ESBC |
| #define CONFIG_U_BOOT_HDR_SIZE (16 << 10) |
| /* |
| * HDR would be appended at end of image and copied to DDR along |
| * with U-Boot image. Here u-boot max. size is 512K. So if binary |
| * size increases then increase this size in case of secure boot as |
| * it uses raw u-boot image instead of fit image. |
| */ |
| #define CONFIG_SYS_MONITOR_LEN (0x100000 + CONFIG_U_BOOT_HDR_SIZE) |
| #else |
| #define CONFIG_SYS_MONITOR_LEN 0x100000 |
| #endif /* ifdef CONFIG_NXP_ESBC */ |
| |
| #endif |
| |
| #endif /* __LS1088_COMMON_H */ |