| // SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) |
| /* |
| * Copyright (C) STMicroelectronics 2017 - All Rights Reserved |
| * Author: Ludovic Barre <ludovic.barre@st.com> for STMicroelectronics. |
| */ |
| #include <dt-bindings/interrupt-controller/arm-gic.h> |
| #include <dt-bindings/clock/stm32mp1-clks.h> |
| #include <dt-bindings/reset/stm32mp1-resets.h> |
| |
| / { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| |
| cpus { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| cpu0: cpu@0 { |
| compatible = "arm,cortex-a7"; |
| clock-frequency = <650000000>; |
| device_type = "cpu"; |
| reg = <0>; |
| operating-points-v2 = <&cpu0_opp_table>; |
| nvmem-cells = <&part_number_otp>; |
| nvmem-cell-names = "part_number"; |
| }; |
| }; |
| |
| cpu0_opp_table: cpu0-opp-table { |
| compatible = "operating-points-v2"; |
| opp-shared; |
| opp-650000000 { |
| opp-hz = /bits/ 64 <650000000>; |
| opp-microvolt = <1200000>; |
| opp-supported-hw = <0x1>; |
| }; |
| opp-800000000 { |
| opp-hz = /bits/ 64 <800000000>; |
| opp-microvolt = <1350000>; |
| opp-supported-hw = <0x2>; |
| }; |
| }; |
| |
| arm-pmu { |
| compatible = "arm,cortex-a7-pmu"; |
| interrupts = <GIC_SPI 200 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-affinity = <&cpu0>; |
| interrupt-parent = <&intc>; |
| }; |
| |
| psci { |
| compatible = "arm,psci-1.0"; |
| method = "smc"; |
| }; |
| |
| intc: interrupt-controller@a0021000 { |
| compatible = "arm,cortex-a7-gic"; |
| #interrupt-cells = <3>; |
| interrupt-controller; |
| reg = <0xa0021000 0x1000>, |
| <0xa0022000 0x2000>; |
| }; |
| |
| timer { |
| compatible = "arm,armv7-timer"; |
| interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>, |
| <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>, |
| <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>, |
| <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>; |
| interrupt-parent = <&intc>; |
| }; |
| |
| clocks { |
| clk_hse: clk-hse { |
| #clock-cells = <0>; |
| compatible = "fixed-clock"; |
| clock-frequency = <24000000>; |
| }; |
| |
| clk_hsi: clk-hsi { |
| #clock-cells = <0>; |
| compatible = "fixed-clock"; |
| clock-frequency = <64000000>; |
| }; |
| |
| clk_lse: clk-lse { |
| #clock-cells = <0>; |
| compatible = "fixed-clock"; |
| clock-frequency = <32768>; |
| }; |
| |
| clk_lsi: clk-lsi { |
| #clock-cells = <0>; |
| compatible = "fixed-clock"; |
| clock-frequency = <32000>; |
| }; |
| |
| clk_csi: clk-csi { |
| #clock-cells = <0>; |
| compatible = "fixed-clock"; |
| clock-frequency = <4000000>; |
| }; |
| }; |
| |
| thermal-zones { |
| cpu_thermal: cpu-thermal { |
| polling-delay-passive = <0>; |
| polling-delay = <0>; |
| thermal-sensors = <&dts>; |
| |
| trips { |
| cpu_alert1: cpu-alert1 { |
| temperature = <85000>; |
| hysteresis = <0>; |
| type = "passive"; |
| }; |
| |
| cpu-crit { |
| temperature = <120000>; |
| hysteresis = <0>; |
| type = "critical"; |
| }; |
| }; |
| |
| cooling-maps { |
| }; |
| }; |
| }; |
| |
| booster: regulator-booster { |
| compatible = "st,stm32mp1-booster"; |
| st,syscfg = <&syscfg>; |
| status = "disabled"; |
| }; |
| |
| soc { |
| compatible = "simple-bus"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| interrupt-parent = <&intc>; |
| ranges; |
| |
| timers2: timer@40000000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "st,stm32-timers"; |
| reg = <0x40000000 0x400>; |
| clocks = <&rcc TIM2_K>; |
| clock-names = "int"; |
| dmas = <&dmamux1 18 0x400 0x1>, |
| <&dmamux1 19 0x400 0x1>, |
| <&dmamux1 20 0x400 0x1>, |
| <&dmamux1 21 0x400 0x1>, |
| <&dmamux1 22 0x400 0x1>; |
| dma-names = "ch1", "ch2", "ch3", "ch4", "up"; |
| status = "disabled"; |
| |
| pwm { |
| compatible = "st,stm32-pwm"; |
| #pwm-cells = <3>; |
| status = "disabled"; |
| }; |
| |
| timer@1 { |
| compatible = "st,stm32h7-timer-trigger"; |
| reg = <1>; |
| status = "disabled"; |
| }; |
| |
| counter { |
| compatible = "st,stm32-timer-counter"; |
| status = "disabled"; |
| }; |
| }; |
| |
| timers3: timer@40001000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "st,stm32-timers"; |
| reg = <0x40001000 0x400>; |
| clocks = <&rcc TIM3_K>; |
| clock-names = "int"; |
| dmas = <&dmamux1 23 0x400 0x1>, |
| <&dmamux1 24 0x400 0x1>, |
| <&dmamux1 25 0x400 0x1>, |
| <&dmamux1 26 0x400 0x1>, |
| <&dmamux1 27 0x400 0x1>, |
| <&dmamux1 28 0x400 0x1>; |
| dma-names = "ch1", "ch2", "ch3", "ch4", "up", "trig"; |
| status = "disabled"; |
| |
| pwm { |
| compatible = "st,stm32-pwm"; |
| #pwm-cells = <3>; |
| status = "disabled"; |
| }; |
| |
| timer@2 { |
| compatible = "st,stm32h7-timer-trigger"; |
| reg = <2>; |
| status = "disabled"; |
| }; |
| |
| counter { |
| compatible = "st,stm32-timer-counter"; |
| status = "disabled"; |
| }; |
| }; |
| |
| timers4: timer@40002000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "st,stm32-timers"; |
| reg = <0x40002000 0x400>; |
| clocks = <&rcc TIM4_K>; |
| clock-names = "int"; |
| dmas = <&dmamux1 29 0x400 0x1>, |
| <&dmamux1 30 0x400 0x1>, |
| <&dmamux1 31 0x400 0x1>, |
| <&dmamux1 32 0x400 0x1>; |
| dma-names = "ch1", "ch2", "ch3", "ch4"; |
| status = "disabled"; |
| |
| pwm { |
| compatible = "st,stm32-pwm"; |
| #pwm-cells = <3>; |
| status = "disabled"; |
| }; |
| |
| timer@3 { |
| compatible = "st,stm32h7-timer-trigger"; |
| reg = <3>; |
| status = "disabled"; |
| }; |
| |
| counter { |
| compatible = "st,stm32-timer-counter"; |
| status = "disabled"; |
| }; |
| }; |
| |
| timers5: timer@40003000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "st,stm32-timers"; |
| reg = <0x40003000 0x400>; |
| clocks = <&rcc TIM5_K>; |
| clock-names = "int"; |
| dmas = <&dmamux1 55 0x400 0x1>, |
| <&dmamux1 56 0x400 0x1>, |
| <&dmamux1 57 0x400 0x1>, |
| <&dmamux1 58 0x400 0x1>, |
| <&dmamux1 59 0x400 0x1>, |
| <&dmamux1 60 0x400 0x1>; |
| dma-names = "ch1", "ch2", "ch3", "ch4", "up", "trig"; |
| status = "disabled"; |
| |
| pwm { |
| compatible = "st,stm32-pwm"; |
| #pwm-cells = <3>; |
| status = "disabled"; |
| }; |
| |
| timer@4 { |
| compatible = "st,stm32h7-timer-trigger"; |
| reg = <4>; |
| status = "disabled"; |
| }; |
| |
| counter { |
| compatible = "st,stm32-timer-counter"; |
| status = "disabled"; |
| }; |
| }; |
| |
| timers6: timer@40004000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "st,stm32-timers"; |
| reg = <0x40004000 0x400>; |
| clocks = <&rcc TIM6_K>; |
| clock-names = "int"; |
| dmas = <&dmamux1 69 0x400 0x1>; |
| dma-names = "up"; |
| status = "disabled"; |
| |
| timer@5 { |
| compatible = "st,stm32h7-timer-trigger"; |
| reg = <5>; |
| status = "disabled"; |
| }; |
| }; |
| |
| timers7: timer@40005000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "st,stm32-timers"; |
| reg = <0x40005000 0x400>; |
| clocks = <&rcc TIM7_K>; |
| clock-names = "int"; |
| dmas = <&dmamux1 70 0x400 0x1>; |
| dma-names = "up"; |
| status = "disabled"; |
| |
| timer@6 { |
| compatible = "st,stm32h7-timer-trigger"; |
| reg = <6>; |
| status = "disabled"; |
| }; |
| }; |
| |
| timers12: timer@40006000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "st,stm32-timers"; |
| reg = <0x40006000 0x400>; |
| clocks = <&rcc TIM12_K>; |
| clock-names = "int"; |
| status = "disabled"; |
| |
| pwm { |
| compatible = "st,stm32-pwm"; |
| #pwm-cells = <3>; |
| status = "disabled"; |
| }; |
| |
| timer@11 { |
| compatible = "st,stm32h7-timer-trigger"; |
| reg = <11>; |
| status = "disabled"; |
| }; |
| }; |
| |
| timers13: timer@40007000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "st,stm32-timers"; |
| reg = <0x40007000 0x400>; |
| clocks = <&rcc TIM13_K>; |
| clock-names = "int"; |
| status = "disabled"; |
| |
| pwm { |
| compatible = "st,stm32-pwm"; |
| #pwm-cells = <3>; |
| status = "disabled"; |
| }; |
| |
| timer@12 { |
| compatible = "st,stm32h7-timer-trigger"; |
| reg = <12>; |
| status = "disabled"; |
| }; |
| }; |
| |
| timers14: timer@40008000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "st,stm32-timers"; |
| reg = <0x40008000 0x400>; |
| clocks = <&rcc TIM14_K>; |
| clock-names = "int"; |
| status = "disabled"; |
| |
| pwm { |
| compatible = "st,stm32-pwm"; |
| #pwm-cells = <3>; |
| status = "disabled"; |
| }; |
| |
| timer@13 { |
| compatible = "st,stm32h7-timer-trigger"; |
| reg = <13>; |
| status = "disabled"; |
| }; |
| }; |
| |
| lptimer1: timer@40009000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "st,stm32-lptimer"; |
| reg = <0x40009000 0x400>; |
| interrupts-extended = <&exti 47 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&rcc LPTIM1_K>; |
| clock-names = "mux"; |
| wakeup-source; |
| status = "disabled"; |
| |
| pwm { |
| compatible = "st,stm32-pwm-lp"; |
| #pwm-cells = <3>; |
| status = "disabled"; |
| }; |
| |
| trigger@0 { |
| compatible = "st,stm32-lptimer-trigger"; |
| reg = <0>; |
| status = "disabled"; |
| }; |
| |
| counter { |
| compatible = "st,stm32-lptimer-counter"; |
| status = "disabled"; |
| }; |
| }; |
| |
| spi2: spi@4000b000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "st,stm32h7-spi"; |
| reg = <0x4000b000 0x400>; |
| interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&rcc SPI2_K>; |
| resets = <&rcc SPI2_R>; |
| dmas = <&dmamux1 39 0x400 0x05>, |
| <&dmamux1 40 0x400 0x05>; |
| dma-names = "rx", "tx"; |
| status = "disabled"; |
| }; |
| |
| i2s2: audio-controller@4000b000 { |
| compatible = "st,stm32h7-i2s"; |
| #sound-dai-cells = <0>; |
| reg = <0x4000b000 0x400>; |
| interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>; |
| dmas = <&dmamux1 39 0x400 0x01>, |
| <&dmamux1 40 0x400 0x01>; |
| dma-names = "rx", "tx"; |
| status = "disabled"; |
| }; |
| |
| spi3: spi@4000c000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "st,stm32h7-spi"; |
| reg = <0x4000c000 0x400>; |
| interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&rcc SPI3_K>; |
| resets = <&rcc SPI3_R>; |
| dmas = <&dmamux1 61 0x400 0x05>, |
| <&dmamux1 62 0x400 0x05>; |
| dma-names = "rx", "tx"; |
| status = "disabled"; |
| }; |
| |
| i2s3: audio-controller@4000c000 { |
| compatible = "st,stm32h7-i2s"; |
| #sound-dai-cells = <0>; |
| reg = <0x4000c000 0x400>; |
| interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>; |
| dmas = <&dmamux1 61 0x400 0x01>, |
| <&dmamux1 62 0x400 0x01>; |
| dma-names = "rx", "tx"; |
| status = "disabled"; |
| }; |
| |
| spdifrx: audio-controller@4000d000 { |
| compatible = "st,stm32h7-spdifrx"; |
| #sound-dai-cells = <0>; |
| reg = <0x4000d000 0x400>; |
| clocks = <&rcc SPDIF_K>; |
| clock-names = "kclk"; |
| interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>; |
| dmas = <&dmamux1 93 0x400 0x01>, |
| <&dmamux1 94 0x400 0x01>; |
| dma-names = "rx", "rx-ctrl"; |
| status = "disabled"; |
| }; |
| |
| usart2: serial@4000e000 { |
| compatible = "st,stm32h7-uart"; |
| reg = <0x4000e000 0x400>; |
| interrupts-extended = <&exti 27 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&rcc USART2_K>; |
| wakeup-source; |
| dmas = <&dmamux1 43 0x400 0x15>, |
| <&dmamux1 44 0x400 0x11>; |
| dma-names = "rx", "tx"; |
| status = "disabled"; |
| }; |
| |
| usart3: serial@4000f000 { |
| compatible = "st,stm32h7-uart"; |
| reg = <0x4000f000 0x400>; |
| interrupts-extended = <&exti 28 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&rcc USART3_K>; |
| wakeup-source; |
| dmas = <&dmamux1 45 0x400 0x15>, |
| <&dmamux1 46 0x400 0x11>; |
| dma-names = "rx", "tx"; |
| status = "disabled"; |
| }; |
| |
| uart4: serial@40010000 { |
| compatible = "st,stm32h7-uart"; |
| reg = <0x40010000 0x400>; |
| interrupts-extended = <&exti 30 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&rcc UART4_K>; |
| wakeup-source; |
| dmas = <&dmamux1 63 0x400 0x15>, |
| <&dmamux1 64 0x400 0x11>; |
| dma-names = "rx", "tx"; |
| status = "disabled"; |
| }; |
| |
| uart5: serial@40011000 { |
| compatible = "st,stm32h7-uart"; |
| reg = <0x40011000 0x400>; |
| interrupts-extended = <&exti 31 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&rcc UART5_K>; |
| wakeup-source; |
| dmas = <&dmamux1 65 0x400 0x15>, |
| <&dmamux1 66 0x400 0x11>; |
| dma-names = "rx", "tx"; |
| status = "disabled"; |
| }; |
| |
| i2c1: i2c@40012000 { |
| compatible = "st,stm32mp15-i2c"; |
| reg = <0x40012000 0x400>; |
| interrupt-names = "event", "error"; |
| interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&rcc I2C1_K>; |
| resets = <&rcc I2C1_R>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| st,syscfg-fmp = <&syscfg 0x4 0x1>; |
| wakeup-source; |
| i2c-analog-filter; |
| status = "disabled"; |
| }; |
| |
| i2c2: i2c@40013000 { |
| compatible = "st,stm32mp15-i2c"; |
| reg = <0x40013000 0x400>; |
| interrupt-names = "event", "error"; |
| interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&rcc I2C2_K>; |
| resets = <&rcc I2C2_R>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| st,syscfg-fmp = <&syscfg 0x4 0x2>; |
| wakeup-source; |
| i2c-analog-filter; |
| status = "disabled"; |
| }; |
| |
| i2c3: i2c@40014000 { |
| compatible = "st,stm32mp15-i2c"; |
| reg = <0x40014000 0x400>; |
| interrupt-names = "event", "error"; |
| interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&rcc I2C3_K>; |
| resets = <&rcc I2C3_R>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| st,syscfg-fmp = <&syscfg 0x4 0x4>; |
| wakeup-source; |
| i2c-analog-filter; |
| status = "disabled"; |
| }; |
| |
| i2c5: i2c@40015000 { |
| compatible = "st,stm32mp15-i2c"; |
| reg = <0x40015000 0x400>; |
| interrupt-names = "event", "error"; |
| interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&rcc I2C5_K>; |
| resets = <&rcc I2C5_R>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| st,syscfg-fmp = <&syscfg 0x4 0x10>; |
| wakeup-source; |
| i2c-analog-filter; |
| status = "disabled"; |
| }; |
| |
| cec: cec@40016000 { |
| compatible = "st,stm32-cec"; |
| reg = <0x40016000 0x400>; |
| interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&rcc CEC_K>, <&rcc CEC>; |
| clock-names = "cec", "hdmi-cec"; |
| status = "disabled"; |
| }; |
| |
| dac: dac@40017000 { |
| compatible = "st,stm32h7-dac-core"; |
| reg = <0x40017000 0x400>; |
| clocks = <&rcc DAC12>; |
| clock-names = "pclk"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| |
| dac1: dac@1 { |
| compatible = "st,stm32-dac"; |
| #io-channel-cells = <1>; |
| reg = <1>; |
| status = "disabled"; |
| }; |
| |
| dac2: dac@2 { |
| compatible = "st,stm32-dac"; |
| #io-channel-cells = <1>; |
| reg = <2>; |
| status = "disabled"; |
| }; |
| }; |
| |
| uart7: serial@40018000 { |
| compatible = "st,stm32h7-uart"; |
| reg = <0x40018000 0x400>; |
| interrupts-extended = <&exti 32 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&rcc UART7_K>; |
| wakeup-source; |
| dmas = <&dmamux1 79 0x400 0x15>, |
| <&dmamux1 80 0x400 0x11>; |
| dma-names = "rx", "tx"; |
| status = "disabled"; |
| }; |
| |
| uart8: serial@40019000 { |
| compatible = "st,stm32h7-uart"; |
| reg = <0x40019000 0x400>; |
| interrupts-extended = <&exti 33 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&rcc UART8_K>; |
| wakeup-source; |
| dmas = <&dmamux1 81 0x400 0x15>, |
| <&dmamux1 82 0x400 0x11>; |
| dma-names = "rx", "tx"; |
| status = "disabled"; |
| }; |
| |
| timers1: timer@44000000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "st,stm32-timers"; |
| reg = <0x44000000 0x400>; |
| clocks = <&rcc TIM1_K>; |
| clock-names = "int"; |
| dmas = <&dmamux1 11 0x400 0x1>, |
| <&dmamux1 12 0x400 0x1>, |
| <&dmamux1 13 0x400 0x1>, |
| <&dmamux1 14 0x400 0x1>, |
| <&dmamux1 15 0x400 0x1>, |
| <&dmamux1 16 0x400 0x1>, |
| <&dmamux1 17 0x400 0x1>; |
| dma-names = "ch1", "ch2", "ch3", "ch4", |
| "up", "trig", "com"; |
| status = "disabled"; |
| |
| pwm { |
| compatible = "st,stm32-pwm"; |
| #pwm-cells = <3>; |
| status = "disabled"; |
| }; |
| |
| timer@0 { |
| compatible = "st,stm32h7-timer-trigger"; |
| reg = <0>; |
| status = "disabled"; |
| }; |
| |
| counter { |
| compatible = "st,stm32-timer-counter"; |
| status = "disabled"; |
| }; |
| }; |
| |
| timers8: timer@44001000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "st,stm32-timers"; |
| reg = <0x44001000 0x400>; |
| clocks = <&rcc TIM8_K>; |
| clock-names = "int"; |
| dmas = <&dmamux1 47 0x400 0x1>, |
| <&dmamux1 48 0x400 0x1>, |
| <&dmamux1 49 0x400 0x1>, |
| <&dmamux1 50 0x400 0x1>, |
| <&dmamux1 51 0x400 0x1>, |
| <&dmamux1 52 0x400 0x1>, |
| <&dmamux1 53 0x400 0x1>; |
| dma-names = "ch1", "ch2", "ch3", "ch4", |
| "up", "trig", "com"; |
| status = "disabled"; |
| |
| pwm { |
| compatible = "st,stm32-pwm"; |
| #pwm-cells = <3>; |
| status = "disabled"; |
| }; |
| |
| timer@7 { |
| compatible = "st,stm32h7-timer-trigger"; |
| reg = <7>; |
| status = "disabled"; |
| }; |
| |
| counter { |
| compatible = "st,stm32-timer-counter"; |
| status = "disabled"; |
| }; |
| }; |
| |
| usart6: serial@44003000 { |
| compatible = "st,stm32h7-uart"; |
| reg = <0x44003000 0x400>; |
| interrupts-extended = <&exti 29 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&rcc USART6_K>; |
| wakeup-source; |
| dmas = <&dmamux1 71 0x400 0x15>, |
| <&dmamux1 72 0x400 0x11>; |
| dma-names = "rx", "tx"; |
| status = "disabled"; |
| }; |
| |
| spi1: spi@44004000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "st,stm32h7-spi"; |
| reg = <0x44004000 0x400>; |
| interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&rcc SPI1_K>; |
| resets = <&rcc SPI1_R>; |
| dmas = <&dmamux1 37 0x400 0x05>, |
| <&dmamux1 38 0x400 0x05>; |
| dma-names = "rx", "tx"; |
| status = "disabled"; |
| }; |
| |
| i2s1: audio-controller@44004000 { |
| compatible = "st,stm32h7-i2s"; |
| #sound-dai-cells = <0>; |
| reg = <0x44004000 0x400>; |
| interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>; |
| dmas = <&dmamux1 37 0x400 0x01>, |
| <&dmamux1 38 0x400 0x01>; |
| dma-names = "rx", "tx"; |
| status = "disabled"; |
| }; |
| |
| spi4: spi@44005000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "st,stm32h7-spi"; |
| reg = <0x44005000 0x400>; |
| interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&rcc SPI4_K>; |
| resets = <&rcc SPI4_R>; |
| dmas = <&dmamux1 83 0x400 0x05>, |
| <&dmamux1 84 0x400 0x05>; |
| dma-names = "rx", "tx"; |
| status = "disabled"; |
| }; |
| |
| timers15: timer@44006000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "st,stm32-timers"; |
| reg = <0x44006000 0x400>; |
| clocks = <&rcc TIM15_K>; |
| clock-names = "int"; |
| dmas = <&dmamux1 105 0x400 0x1>, |
| <&dmamux1 106 0x400 0x1>, |
| <&dmamux1 107 0x400 0x1>, |
| <&dmamux1 108 0x400 0x1>; |
| dma-names = "ch1", "up", "trig", "com"; |
| status = "disabled"; |
| |
| pwm { |
| compatible = "st,stm32-pwm"; |
| #pwm-cells = <3>; |
| status = "disabled"; |
| }; |
| |
| timer@14 { |
| compatible = "st,stm32h7-timer-trigger"; |
| reg = <14>; |
| status = "disabled"; |
| }; |
| }; |
| |
| timers16: timer@44007000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "st,stm32-timers"; |
| reg = <0x44007000 0x400>; |
| clocks = <&rcc TIM16_K>; |
| clock-names = "int"; |
| dmas = <&dmamux1 109 0x400 0x1>, |
| <&dmamux1 110 0x400 0x1>; |
| dma-names = "ch1", "up"; |
| status = "disabled"; |
| |
| pwm { |
| compatible = "st,stm32-pwm"; |
| #pwm-cells = <3>; |
| status = "disabled"; |
| }; |
| timer@15 { |
| compatible = "st,stm32h7-timer-trigger"; |
| reg = <15>; |
| status = "disabled"; |
| }; |
| }; |
| |
| timers17: timer@44008000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "st,stm32-timers"; |
| reg = <0x44008000 0x400>; |
| clocks = <&rcc TIM17_K>; |
| clock-names = "int"; |
| dmas = <&dmamux1 111 0x400 0x1>, |
| <&dmamux1 112 0x400 0x1>; |
| dma-names = "ch1", "up"; |
| status = "disabled"; |
| |
| pwm { |
| compatible = "st,stm32-pwm"; |
| #pwm-cells = <3>; |
| status = "disabled"; |
| }; |
| |
| timer@16 { |
| compatible = "st,stm32h7-timer-trigger"; |
| reg = <16>; |
| status = "disabled"; |
| }; |
| }; |
| |
| spi5: spi@44009000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "st,stm32h7-spi"; |
| reg = <0x44009000 0x400>; |
| interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&rcc SPI5_K>; |
| resets = <&rcc SPI5_R>; |
| dmas = <&dmamux1 85 0x400 0x05>, |
| <&dmamux1 86 0x400 0x05>; |
| dma-names = "rx", "tx"; |
| status = "disabled"; |
| }; |
| |
| sai1: sai@4400a000 { |
| compatible = "st,stm32h7-sai"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0 0x4400a000 0x400>; |
| reg = <0x4400a000 0x4>, <0x4400a3f0 0x10>; |
| interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>; |
| resets = <&rcc SAI1_R>; |
| status = "disabled"; |
| |
| sai1a: audio-controller@4400a004 { |
| #sound-dai-cells = <0>; |
| |
| compatible = "st,stm32-sai-sub-a"; |
| reg = <0x4 0x20>; |
| clocks = <&rcc SAI1_K>; |
| clock-names = "sai_ck"; |
| dmas = <&dmamux1 87 0x400 0x01>; |
| status = "disabled"; |
| }; |
| |
| sai1b: audio-controller@4400a024 { |
| #sound-dai-cells = <0>; |
| compatible = "st,stm32-sai-sub-b"; |
| reg = <0x24 0x20>; |
| clocks = <&rcc SAI1_K>; |
| clock-names = "sai_ck"; |
| dmas = <&dmamux1 88 0x400 0x01>; |
| status = "disabled"; |
| }; |
| }; |
| |
| sai2: sai@4400b000 { |
| compatible = "st,stm32h7-sai"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0 0x4400b000 0x400>; |
| reg = <0x4400b000 0x4>, <0x4400b3f0 0x10>; |
| interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>; |
| resets = <&rcc SAI2_R>; |
| status = "disabled"; |
| |
| sai2a: audio-controller@4400b004 { |
| #sound-dai-cells = <0>; |
| compatible = "st,stm32-sai-sub-a"; |
| reg = <0x4 0x20>; |
| clocks = <&rcc SAI2_K>; |
| clock-names = "sai_ck"; |
| dmas = <&dmamux1 89 0x400 0x01>; |
| status = "disabled"; |
| }; |
| |
| sai2b: audio-controller@4400b024 { |
| #sound-dai-cells = <0>; |
| compatible = "st,stm32-sai-sub-b"; |
| reg = <0x24 0x20>; |
| clocks = <&rcc SAI2_K>; |
| clock-names = "sai_ck"; |
| dmas = <&dmamux1 90 0x400 0x01>; |
| status = "disabled"; |
| }; |
| }; |
| |
| sai3: sai@4400c000 { |
| compatible = "st,stm32h7-sai"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0 0x4400c000 0x400>; |
| reg = <0x4400c000 0x4>, <0x4400c3f0 0x10>; |
| interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>; |
| resets = <&rcc SAI3_R>; |
| status = "disabled"; |
| |
| sai3a: audio-controller@4400c004 { |
| #sound-dai-cells = <0>; |
| compatible = "st,stm32-sai-sub-a"; |
| reg = <0x04 0x20>; |
| clocks = <&rcc SAI3_K>; |
| clock-names = "sai_ck"; |
| dmas = <&dmamux1 113 0x400 0x01>; |
| status = "disabled"; |
| }; |
| |
| sai3b: audio-controller@4400c024 { |
| #sound-dai-cells = <0>; |
| compatible = "st,stm32-sai-sub-b"; |
| reg = <0x24 0x20>; |
| clocks = <&rcc SAI3_K>; |
| clock-names = "sai_ck"; |
| dmas = <&dmamux1 114 0x400 0x01>; |
| status = "disabled"; |
| }; |
| }; |
| |
| dfsdm: dfsdm@4400d000 { |
| compatible = "st,stm32mp1-dfsdm"; |
| reg = <0x4400d000 0x800>; |
| clocks = <&rcc DFSDM_K>; |
| clock-names = "dfsdm"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| |
| dfsdm0: filter@0 { |
| compatible = "st,stm32-dfsdm-adc"; |
| #io-channel-cells = <1>; |
| reg = <0>; |
| interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>; |
| dmas = <&dmamux1 101 0x400 0x01>; |
| dma-names = "rx"; |
| status = "disabled"; |
| }; |
| |
| dfsdm1: filter@1 { |
| compatible = "st,stm32-dfsdm-adc"; |
| #io-channel-cells = <1>; |
| reg = <1>; |
| interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>; |
| dmas = <&dmamux1 102 0x400 0x01>; |
| dma-names = "rx"; |
| status = "disabled"; |
| }; |
| |
| dfsdm2: filter@2 { |
| compatible = "st,stm32-dfsdm-adc"; |
| #io-channel-cells = <1>; |
| reg = <2>; |
| interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>; |
| dmas = <&dmamux1 103 0x400 0x01>; |
| dma-names = "rx"; |
| status = "disabled"; |
| }; |
| |
| dfsdm3: filter@3 { |
| compatible = "st,stm32-dfsdm-adc"; |
| #io-channel-cells = <1>; |
| reg = <3>; |
| interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>; |
| dmas = <&dmamux1 104 0x400 0x01>; |
| dma-names = "rx"; |
| status = "disabled"; |
| }; |
| |
| dfsdm4: filter@4 { |
| compatible = "st,stm32-dfsdm-adc"; |
| #io-channel-cells = <1>; |
| reg = <4>; |
| interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>; |
| dmas = <&dmamux1 91 0x400 0x01>; |
| dma-names = "rx"; |
| status = "disabled"; |
| }; |
| |
| dfsdm5: filter@5 { |
| compatible = "st,stm32-dfsdm-adc"; |
| #io-channel-cells = <1>; |
| reg = <5>; |
| interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>; |
| dmas = <&dmamux1 92 0x400 0x01>; |
| dma-names = "rx"; |
| status = "disabled"; |
| }; |
| }; |
| |
| dma1: dma-controller@48000000 { |
| compatible = "st,stm32-dma"; |
| reg = <0x48000000 0x400>; |
| interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&rcc DMA1>; |
| resets = <&rcc DMA1_R>; |
| #dma-cells = <4>; |
| st,mem2mem; |
| dma-requests = <8>; |
| }; |
| |
| dma2: dma-controller@48001000 { |
| compatible = "st,stm32-dma"; |
| reg = <0x48001000 0x400>; |
| interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&rcc DMA2>; |
| resets = <&rcc DMA2_R>; |
| #dma-cells = <4>; |
| st,mem2mem; |
| dma-requests = <8>; |
| }; |
| |
| dmamux1: dma-router@48002000 { |
| compatible = "st,stm32h7-dmamux"; |
| reg = <0x48002000 0x40>; |
| #dma-cells = <3>; |
| dma-requests = <128>; |
| dma-masters = <&dma1 &dma2>; |
| dma-channels = <16>; |
| clocks = <&rcc DMAMUX>; |
| resets = <&rcc DMAMUX_R>; |
| }; |
| |
| adc: adc@48003000 { |
| compatible = "st,stm32mp1-adc-core"; |
| reg = <0x48003000 0x400>; |
| interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&rcc ADC12>, <&rcc ADC12_K>; |
| clock-names = "bus", "adc"; |
| interrupt-controller; |
| st,syscfg = <&syscfg>; |
| #interrupt-cells = <1>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| |
| adc1: adc@0 { |
| compatible = "st,stm32mp1-adc"; |
| #io-channel-cells = <1>; |
| reg = <0x0>; |
| interrupt-parent = <&adc>; |
| interrupts = <0>; |
| dmas = <&dmamux1 9 0x400 0x01>; |
| dma-names = "rx"; |
| status = "disabled"; |
| }; |
| |
| adc2: adc@100 { |
| compatible = "st,stm32mp1-adc"; |
| #io-channel-cells = <1>; |
| reg = <0x100>; |
| interrupt-parent = <&adc>; |
| interrupts = <1>; |
| dmas = <&dmamux1 10 0x400 0x01>; |
| dma-names = "rx"; |
| status = "disabled"; |
| }; |
| }; |
| |
| sdmmc3: mmc@48004000 { |
| compatible = "st,stm32-sdmmc2", "arm,pl18x", "arm,primecell"; |
| arm,primecell-periphid = <0x00253180>; |
| reg = <0x48004000 0x400>; |
| interrupts = <GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "cmd_irq"; |
| clocks = <&rcc SDMMC3_K>; |
| clock-names = "apb_pclk"; |
| resets = <&rcc SDMMC3_R>; |
| cap-sd-highspeed; |
| cap-mmc-highspeed; |
| max-frequency = <120000000>; |
| status = "disabled"; |
| }; |
| |
| usbotg_hs: usb-otg@49000000 { |
| compatible = "st,stm32mp15-hsotg", "snps,dwc2"; |
| reg = <0x49000000 0x10000>; |
| clocks = <&rcc USBO_K>; |
| clock-names = "otg"; |
| resets = <&rcc USBO_R>; |
| reset-names = "dwc2"; |
| interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; |
| g-rx-fifo-size = <512>; |
| g-np-tx-fifo-size = <32>; |
| g-tx-fifo-size = <256 16 16 16 16 16 16 16>; |
| dr_mode = "otg"; |
| otg-rev = <0x200>; |
| usb33d-supply = <&usb33>; |
| status = "disabled"; |
| }; |
| |
| hwspinlock: hwspinlock@4c000000 { |
| compatible = "st,stm32-hwspinlock"; |
| #hwlock-cells = <1>; |
| reg = <0x4c000000 0x400>; |
| clocks = <&rcc HSEM>; |
| clock-names = "hwspinlock"; |
| }; |
| |
| ipcc: mailbox@4c001000 { |
| compatible = "st,stm32mp1-ipcc"; |
| #mbox-cells = <1>; |
| reg = <0x4c001000 0x400>; |
| st,proc-id = <0>; |
| interrupts-extended = |
| <&intc GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>, |
| <&intc GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>, |
| <&exti 61 1>; |
| interrupt-names = "rx", "tx", "wakeup"; |
| clocks = <&rcc IPCC>; |
| wakeup-source; |
| status = "disabled"; |
| }; |
| |
| dcmi: dcmi@4c006000 { |
| compatible = "st,stm32-dcmi"; |
| reg = <0x4c006000 0x400>; |
| interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>; |
| resets = <&rcc CAMITF_R>; |
| clocks = <&rcc DCMI>; |
| clock-names = "mclk"; |
| dmas = <&dmamux1 75 0x400 0x01>; |
| dma-names = "tx"; |
| status = "disabled"; |
| }; |
| |
| rcc: rcc@50000000 { |
| compatible = "st,stm32mp1-rcc", "syscon"; |
| reg = <0x50000000 0x1000>; |
| #clock-cells = <1>; |
| #reset-cells = <1>; |
| |
| clock-names = "hse", "hsi", "csi", "lse", "lsi"; |
| clocks = <&clk_hse>, <&clk_hsi>, <&clk_csi>, |
| <&clk_lse>, <&clk_lsi>; |
| }; |
| |
| pwr_regulators: pwr@50001000 { |
| compatible = "st,stm32mp1,pwr-reg"; |
| reg = <0x50001000 0x10>; |
| |
| reg11: reg11 { |
| regulator-name = "reg11"; |
| regulator-min-microvolt = <1100000>; |
| regulator-max-microvolt = <1100000>; |
| }; |
| |
| reg18: reg18 { |
| regulator-name = "reg18"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| |
| usb33: usb33 { |
| regulator-name = "usb33"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| }; |
| }; |
| |
| pwr_mcu: pwr_mcu@50001014 { |
| compatible = "st,stm32mp151-pwr-mcu", "syscon"; |
| reg = <0x50001014 0x4>; |
| }; |
| |
| exti: interrupt-controller@5000d000 { |
| compatible = "st,stm32mp1-exti", "syscon"; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| reg = <0x5000d000 0x400>; |
| }; |
| |
| syscfg: syscon@50020000 { |
| compatible = "st,stm32mp157-syscfg", "syscon"; |
| reg = <0x50020000 0x400>; |
| clocks = <&rcc SYSCFG>; |
| }; |
| |
| lptimer2: timer@50021000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "st,stm32-lptimer"; |
| reg = <0x50021000 0x400>; |
| interrupts-extended = <&exti 48 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&rcc LPTIM2_K>; |
| clock-names = "mux"; |
| wakeup-source; |
| status = "disabled"; |
| |
| pwm { |
| compatible = "st,stm32-pwm-lp"; |
| #pwm-cells = <3>; |
| status = "disabled"; |
| }; |
| |
| trigger@1 { |
| compatible = "st,stm32-lptimer-trigger"; |
| reg = <1>; |
| status = "disabled"; |
| }; |
| |
| counter { |
| compatible = "st,stm32-lptimer-counter"; |
| status = "disabled"; |
| }; |
| }; |
| |
| lptimer3: timer@50022000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "st,stm32-lptimer"; |
| reg = <0x50022000 0x400>; |
| interrupts-extended = <&exti 50 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&rcc LPTIM3_K>; |
| clock-names = "mux"; |
| wakeup-source; |
| status = "disabled"; |
| |
| pwm { |
| compatible = "st,stm32-pwm-lp"; |
| #pwm-cells = <3>; |
| status = "disabled"; |
| }; |
| |
| trigger@2 { |
| compatible = "st,stm32-lptimer-trigger"; |
| reg = <2>; |
| status = "disabled"; |
| }; |
| }; |
| |
| lptimer4: timer@50023000 { |
| compatible = "st,stm32-lptimer"; |
| reg = <0x50023000 0x400>; |
| interrupts-extended = <&exti 52 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&rcc LPTIM4_K>; |
| clock-names = "mux"; |
| wakeup-source; |
| status = "disabled"; |
| |
| pwm { |
| compatible = "st,stm32-pwm-lp"; |
| #pwm-cells = <3>; |
| status = "disabled"; |
| }; |
| }; |
| |
| lptimer5: timer@50024000 { |
| compatible = "st,stm32-lptimer"; |
| reg = <0x50024000 0x400>; |
| interrupts-extended = <&exti 53 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&rcc LPTIM5_K>; |
| clock-names = "mux"; |
| wakeup-source; |
| status = "disabled"; |
| |
| pwm { |
| compatible = "st,stm32-pwm-lp"; |
| #pwm-cells = <3>; |
| status = "disabled"; |
| }; |
| }; |
| |
| vrefbuf: vrefbuf@50025000 { |
| compatible = "st,stm32-vrefbuf"; |
| reg = <0x50025000 0x8>; |
| regulator-min-microvolt = <1500000>; |
| regulator-max-microvolt = <2500000>; |
| clocks = <&rcc VREF>; |
| status = "disabled"; |
| }; |
| |
| sai4: sai@50027000 { |
| compatible = "st,stm32h7-sai"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0 0x50027000 0x400>; |
| reg = <0x50027000 0x4>, <0x500273f0 0x10>; |
| interrupts = <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>; |
| resets = <&rcc SAI4_R>; |
| status = "disabled"; |
| |
| sai4a: audio-controller@50027004 { |
| #sound-dai-cells = <0>; |
| compatible = "st,stm32-sai-sub-a"; |
| reg = <0x04 0x20>; |
| clocks = <&rcc SAI4_K>; |
| clock-names = "sai_ck"; |
| dmas = <&dmamux1 99 0x400 0x01>; |
| status = "disabled"; |
| }; |
| |
| sai4b: audio-controller@50027024 { |
| #sound-dai-cells = <0>; |
| compatible = "st,stm32-sai-sub-b"; |
| reg = <0x24 0x20>; |
| clocks = <&rcc SAI4_K>; |
| clock-names = "sai_ck"; |
| dmas = <&dmamux1 100 0x400 0x01>; |
| status = "disabled"; |
| }; |
| }; |
| |
| dts: thermal@50028000 { |
| compatible = "st,stm32-thermal"; |
| reg = <0x50028000 0x100>; |
| interrupts = <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&rcc TMPSENS>; |
| clock-names = "pclk"; |
| #thermal-sensor-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| hash1: hash@54002000 { |
| compatible = "st,stm32f756-hash"; |
| reg = <0x54002000 0x400>; |
| interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&rcc HASH1>; |
| resets = <&rcc HASH1_R>; |
| dmas = <&mdma1 31 0x2 0x1000A02 0x0 0x0>; |
| dma-names = "in"; |
| dma-maxburst = <2>; |
| status = "disabled"; |
| }; |
| |
| rng1: rng@54003000 { |
| compatible = "st,stm32-rng"; |
| reg = <0x54003000 0x400>; |
| clocks = <&rcc RNG1_K>; |
| resets = <&rcc RNG1_R>; |
| status = "disabled"; |
| }; |
| |
| mdma1: dma-controller@58000000 { |
| compatible = "st,stm32h7-mdma"; |
| reg = <0x58000000 0x1000>; |
| interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&rcc MDMA>; |
| resets = <&rcc MDMA_R>; |
| #dma-cells = <5>; |
| dma-channels = <32>; |
| dma-requests = <48>; |
| }; |
| |
| fmc: memory-controller@58002000 { |
| #address-cells = <2>; |
| #size-cells = <1>; |
| compatible = "st,stm32mp1-fmc2-ebi"; |
| reg = <0x58002000 0x1000>; |
| clocks = <&rcc FMC_K>; |
| resets = <&rcc FMC_R>; |
| status = "disabled"; |
| |
| ranges = <0 0 0x60000000 0x04000000>, /* EBI CS 1 */ |
| <1 0 0x64000000 0x04000000>, /* EBI CS 2 */ |
| <2 0 0x68000000 0x04000000>, /* EBI CS 3 */ |
| <3 0 0x6c000000 0x04000000>, /* EBI CS 4 */ |
| <4 0 0x80000000 0x10000000>; /* NAND */ |
| |
| nand-controller@4,0 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "st,stm32mp1-fmc2-nfc"; |
| reg = <4 0x00000000 0x1000>, |
| <4 0x08010000 0x1000>, |
| <4 0x08020000 0x1000>, |
| <4 0x01000000 0x1000>, |
| <4 0x09010000 0x1000>, |
| <4 0x09020000 0x1000>; |
| interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>; |
| dmas = <&mdma1 20 0x2 0x12000a02 0x0 0x0>, |
| <&mdma1 20 0x2 0x12000a08 0x0 0x0>, |
| <&mdma1 21 0x2 0x12000a0a 0x0 0x0>; |
| dma-names = "tx", "rx", "ecc"; |
| status = "disabled"; |
| }; |
| }; |
| |
| qspi: spi@58003000 { |
| compatible = "st,stm32f469-qspi"; |
| reg = <0x58003000 0x1000>, <0x70000000 0x10000000>; |
| reg-names = "qspi", "qspi_mm"; |
| interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>; |
| dmas = <&mdma1 22 0x2 0x10100002 0x0 0x0>, |
| <&mdma1 22 0x2 0x10100008 0x0 0x0>; |
| dma-names = "tx", "rx"; |
| clocks = <&rcc QSPI_K>; |
| resets = <&rcc QSPI_R>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| sdmmc1: mmc@58005000 { |
| compatible = "st,stm32-sdmmc2", "arm,pl18x", "arm,primecell"; |
| arm,primecell-periphid = <0x00253180>; |
| reg = <0x58005000 0x1000>; |
| interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "cmd_irq"; |
| clocks = <&rcc SDMMC1_K>; |
| clock-names = "apb_pclk"; |
| resets = <&rcc SDMMC1_R>; |
| cap-sd-highspeed; |
| cap-mmc-highspeed; |
| max-frequency = <120000000>; |
| status = "disabled"; |
| }; |
| |
| sdmmc2: mmc@58007000 { |
| compatible = "st,stm32-sdmmc2", "arm,pl18x", "arm,primecell"; |
| arm,primecell-periphid = <0x00253180>; |
| reg = <0x58007000 0x1000>; |
| interrupts = <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "cmd_irq"; |
| clocks = <&rcc SDMMC2_K>; |
| clock-names = "apb_pclk"; |
| resets = <&rcc SDMMC2_R>; |
| cap-sd-highspeed; |
| cap-mmc-highspeed; |
| max-frequency = <120000000>; |
| status = "disabled"; |
| }; |
| |
| crc1: crc@58009000 { |
| compatible = "st,stm32f7-crc"; |
| reg = <0x58009000 0x400>; |
| clocks = <&rcc CRC1>; |
| status = "disabled"; |
| }; |
| |
| ethernet0: ethernet@5800a000 { |
| compatible = "st,stm32mp1-dwmac", "snps,dwmac-4.20a"; |
| reg = <0x5800a000 0x2000>; |
| reg-names = "stmmaceth"; |
| interrupts-extended = <&intc GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "macirq"; |
| clock-names = "stmmaceth", |
| "mac-clk-tx", |
| "mac-clk-rx", |
| "eth-ck", |
| "ptp_ref", |
| "ethstp"; |
| clocks = <&rcc ETHMAC>, |
| <&rcc ETHTX>, |
| <&rcc ETHRX>, |
| <&rcc ETHCK_K>, |
| <&rcc ETHPTP_K>, |
| <&rcc ETHSTP>; |
| st,syscon = <&syscfg 0x4>; |
| snps,mixed-burst; |
| snps,pbl = <2>; |
| snps,en-tx-lpi-clockgating; |
| snps,axi-config = <&stmmac_axi_config_0>; |
| snps,tso; |
| status = "disabled"; |
| |
| stmmac_axi_config_0: stmmac-axi-config { |
| snps,wr_osr_lmt = <0x7>; |
| snps,rd_osr_lmt = <0x7>; |
| snps,blen = <0 0 0 0 16 8 4>; |
| }; |
| }; |
| |
| usbh_ohci: usb@5800c000 { |
| compatible = "generic-ohci"; |
| reg = <0x5800c000 0x1000>; |
| clocks = <&usbphyc>, <&rcc USBH>; |
| resets = <&rcc USBH_R>; |
| interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>; |
| status = "disabled"; |
| }; |
| |
| usbh_ehci: usb@5800d000 { |
| compatible = "generic-ehci"; |
| reg = <0x5800d000 0x1000>; |
| clocks = <&usbphyc>, <&rcc USBH>; |
| resets = <&rcc USBH_R>; |
| interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>; |
| companion = <&usbh_ohci>; |
| status = "disabled"; |
| }; |
| |
| ltdc: display-controller@5a001000 { |
| compatible = "st,stm32-ltdc"; |
| reg = <0x5a001000 0x400>; |
| interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&rcc LTDC_PX>; |
| clock-names = "lcd"; |
| resets = <&rcc LTDC_R>; |
| status = "disabled"; |
| |
| port { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| }; |
| }; |
| |
| iwdg2: watchdog@5a002000 { |
| compatible = "st,stm32mp1-iwdg"; |
| reg = <0x5a002000 0x400>; |
| clocks = <&rcc IWDG2>, <&rcc CK_LSI>; |
| clock-names = "pclk", "lsi"; |
| status = "disabled"; |
| }; |
| |
| usbphyc: usbphyc@5a006000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| #clock-cells = <0>; |
| compatible = "st,stm32mp1-usbphyc"; |
| reg = <0x5a006000 0x1000>; |
| clocks = <&rcc USBPHY_K>; |
| resets = <&rcc USBPHY_R>; |
| vdda1v1-supply = <®11>; |
| vdda1v8-supply = <®18>; |
| status = "disabled"; |
| |
| usbphyc_port0: usb-phy@0 { |
| #phy-cells = <0>; |
| reg = <0>; |
| }; |
| |
| usbphyc_port1: usb-phy@1 { |
| #phy-cells = <1>; |
| reg = <1>; |
| }; |
| }; |
| |
| usart1: serial@5c000000 { |
| compatible = "st,stm32h7-uart"; |
| reg = <0x5c000000 0x400>; |
| interrupts-extended = <&exti 26 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&rcc USART1_K>; |
| wakeup-source; |
| status = "disabled"; |
| }; |
| |
| spi6: spi@5c001000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "st,stm32h7-spi"; |
| reg = <0x5c001000 0x400>; |
| interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&rcc SPI6_K>; |
| resets = <&rcc SPI6_R>; |
| dmas = <&mdma1 34 0x0 0x40008 0x0 0x0>, |
| <&mdma1 35 0x0 0x40002 0x0 0x0>; |
| dma-names = "rx", "tx"; |
| status = "disabled"; |
| }; |
| |
| i2c4: i2c@5c002000 { |
| compatible = "st,stm32mp15-i2c"; |
| reg = <0x5c002000 0x400>; |
| interrupt-names = "event", "error"; |
| interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&rcc I2C4_K>; |
| resets = <&rcc I2C4_R>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| st,syscfg-fmp = <&syscfg 0x4 0x8>; |
| wakeup-source; |
| i2c-analog-filter; |
| status = "disabled"; |
| }; |
| |
| rtc: rtc@5c004000 { |
| compatible = "st,stm32mp1-rtc"; |
| reg = <0x5c004000 0x400>; |
| clocks = <&rcc RTCAPB>, <&rcc RTC>; |
| clock-names = "pclk", "rtc_ck"; |
| interrupts-extended = <&exti 19 IRQ_TYPE_LEVEL_HIGH>; |
| status = "disabled"; |
| }; |
| |
| bsec: efuse@5c005000 { |
| compatible = "st,stm32mp15-bsec"; |
| reg = <0x5c005000 0x400>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| part_number_otp: part_number_otp@4 { |
| reg = <0x4 0x1>; |
| }; |
| ts_cal1: calib@5c { |
| reg = <0x5c 0x2>; |
| }; |
| ts_cal2: calib@5e { |
| reg = <0x5e 0x2>; |
| }; |
| }; |
| |
| i2c6: i2c@5c009000 { |
| compatible = "st,stm32mp15-i2c"; |
| reg = <0x5c009000 0x400>; |
| interrupt-names = "event", "error"; |
| interrupts = <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&rcc I2C6_K>; |
| resets = <&rcc I2C6_R>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| st,syscfg-fmp = <&syscfg 0x4 0x20>; |
| wakeup-source; |
| i2c-analog-filter; |
| status = "disabled"; |
| }; |
| |
| tamp: tamp@5c00a000 { |
| compatible = "st,stm32-tamp", "syscon", "simple-mfd"; |
| reg = <0x5c00a000 0x400>; |
| }; |
| |
| /* |
| * Break node order to solve dependency probe issue between |
| * pinctrl and exti. |
| */ |
| pinctrl: pinctrl@50002000 { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| compatible = "st,stm32mp157-pinctrl"; |
| ranges = <0 0x50002000 0xa400>; |
| interrupt-parent = <&exti>; |
| st,syscfg = <&exti 0x60 0xff>; |
| pins-are-numbered; |
| |
| gpioa: gpio@50002000 { |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| reg = <0x0 0x400>; |
| clocks = <&rcc GPIOA>; |
| st,bank-name = "GPIOA"; |
| status = "disabled"; |
| }; |
| |
| gpiob: gpio@50003000 { |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| reg = <0x1000 0x400>; |
| clocks = <&rcc GPIOB>; |
| st,bank-name = "GPIOB"; |
| status = "disabled"; |
| }; |
| |
| gpioc: gpio@50004000 { |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| reg = <0x2000 0x400>; |
| clocks = <&rcc GPIOC>; |
| st,bank-name = "GPIOC"; |
| status = "disabled"; |
| }; |
| |
| gpiod: gpio@50005000 { |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| reg = <0x3000 0x400>; |
| clocks = <&rcc GPIOD>; |
| st,bank-name = "GPIOD"; |
| status = "disabled"; |
| }; |
| |
| gpioe: gpio@50006000 { |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| reg = <0x4000 0x400>; |
| clocks = <&rcc GPIOE>; |
| st,bank-name = "GPIOE"; |
| status = "disabled"; |
| }; |
| |
| gpiof: gpio@50007000 { |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| reg = <0x5000 0x400>; |
| clocks = <&rcc GPIOF>; |
| st,bank-name = "GPIOF"; |
| status = "disabled"; |
| }; |
| |
| gpiog: gpio@50008000 { |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| reg = <0x6000 0x400>; |
| clocks = <&rcc GPIOG>; |
| st,bank-name = "GPIOG"; |
| status = "disabled"; |
| }; |
| |
| gpioh: gpio@50009000 { |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| reg = <0x7000 0x400>; |
| clocks = <&rcc GPIOH>; |
| st,bank-name = "GPIOH"; |
| status = "disabled"; |
| }; |
| |
| gpioi: gpio@5000a000 { |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| reg = <0x8000 0x400>; |
| clocks = <&rcc GPIOI>; |
| st,bank-name = "GPIOI"; |
| status = "disabled"; |
| }; |
| |
| gpioj: gpio@5000b000 { |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| reg = <0x9000 0x400>; |
| clocks = <&rcc GPIOJ>; |
| st,bank-name = "GPIOJ"; |
| status = "disabled"; |
| }; |
| |
| gpiok: gpio@5000c000 { |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| reg = <0xa000 0x400>; |
| clocks = <&rcc GPIOK>; |
| st,bank-name = "GPIOK"; |
| status = "disabled"; |
| }; |
| }; |
| |
| pinctrl_z: pinctrl@54004000 { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| compatible = "st,stm32mp157-z-pinctrl"; |
| ranges = <0 0x54004000 0x400>; |
| pins-are-numbered; |
| interrupt-parent = <&exti>; |
| st,syscfg = <&exti 0x60 0xff>; |
| |
| gpioz: gpio@54004000 { |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| reg = <0 0x400>; |
| clocks = <&rcc GPIOZ>; |
| st,bank-name = "GPIOZ"; |
| st,bank-ioport = <11>; |
| status = "disabled"; |
| }; |
| }; |
| }; |
| |
| mlahb: ahb { |
| compatible = "st,mlahb", "simple-bus"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| dma-ranges = <0x00000000 0x38000000 0x10000>, |
| <0x10000000 0x10000000 0x60000>, |
| <0x30000000 0x30000000 0x60000>; |
| |
| m4_rproc: m4@10000000 { |
| compatible = "st,stm32mp1-m4"; |
| reg = <0x10000000 0x40000>, |
| <0x30000000 0x40000>, |
| <0x38000000 0x10000>; |
| resets = <&rcc MCU_R>; |
| st,syscfg-holdboot = <&rcc 0x10C 0x1>; |
| st,syscfg-tz = <&rcc 0x000 0x1>; |
| st,syscfg-pdds = <&pwr_mcu 0x0 0x1>; |
| st,syscfg-rsc-tbl = <&tamp 0x144 0xFFFFFFFF>; |
| st,syscfg-m4-state = <&tamp 0x148 0xFFFFFFFF>; |
| status = "disabled"; |
| }; |
| }; |
| }; |