| /* SPDX-License-Identifier: GPL-2.0+ */ |
| #ifndef __UFS_H |
| #define __UFS_H |
| |
| #include <linux/types.h> |
| #include <asm/io.h> |
| #include "unipro.h" |
| |
| struct udevice; |
| |
| #define UFS_CDB_SIZE 16 |
| #define UPIU_TRANSACTION_UIC_CMD 0x1F |
| #define UIC_CMD_SIZE (sizeof(u32) * 4) |
| #define RESPONSE_UPIU_SENSE_DATA_LENGTH 18 |
| #define UFS_MAX_LUNS 0x7F |
| |
| enum { |
| TASK_REQ_UPIU_SIZE_DWORDS = 8, |
| TASK_RSP_UPIU_SIZE_DWORDS = 8, |
| ALIGNED_UPIU_SIZE = 512, |
| }; |
| |
| /* UFS device power modes */ |
| enum ufs_dev_pwr_mode { |
| UFS_ACTIVE_PWR_MODE = 1, |
| UFS_SLEEP_PWR_MODE = 2, |
| UFS_POWERDOWN_PWR_MODE = 3, |
| }; |
| |
| enum ufs_notify_change_status { |
| PRE_CHANGE, |
| POST_CHANGE, |
| }; |
| |
| struct ufs_pa_layer_attr { |
| u32 gear_rx; |
| u32 gear_tx; |
| u32 lane_rx; |
| u32 lane_tx; |
| u32 pwr_rx; |
| u32 pwr_tx; |
| u32 hs_rate; |
| }; |
| |
| struct ufs_pwr_mode_info { |
| bool is_valid; |
| struct ufs_pa_layer_attr info; |
| }; |
| |
| enum ufs_desc_def_size { |
| QUERY_DESC_DEVICE_DEF_SIZE = 0x40, |
| QUERY_DESC_CONFIGURATION_DEF_SIZE = 0x90, |
| QUERY_DESC_UNIT_DEF_SIZE = 0x23, |
| QUERY_DESC_INTERCONNECT_DEF_SIZE = 0x06, |
| QUERY_DESC_GEOMETRY_DEF_SIZE = 0x48, |
| QUERY_DESC_POWER_DEF_SIZE = 0x62, |
| QUERY_DESC_HEALTH_DEF_SIZE = 0x25, |
| }; |
| |
| struct ufs_desc_size { |
| int dev_desc; |
| int pwr_desc; |
| int geom_desc; |
| int interc_desc; |
| int unit_desc; |
| int conf_desc; |
| int hlth_desc; |
| }; |
| |
| /* |
| * Request Descriptor Definitions |
| */ |
| |
| /* Transfer request command type */ |
| enum { |
| UTP_CMD_TYPE_SCSI = 0x0, |
| UTP_CMD_TYPE_UFS = 0x1, |
| UTP_CMD_TYPE_DEV_MANAGE = 0x2, |
| }; |
| |
| /* UTP Transfer Request Command Offset */ |
| #define UPIU_COMMAND_TYPE_OFFSET 28 |
| |
| /* Offset of the response code in the UPIU header */ |
| #define UPIU_RSP_CODE_OFFSET 8 |
| |
| /* To accommodate UFS2.0 required Command type */ |
| enum { |
| UTP_CMD_TYPE_UFS_STORAGE = 0x1, |
| }; |
| |
| enum { |
| UTP_SCSI_COMMAND = 0x00000000, |
| UTP_NATIVE_UFS_COMMAND = 0x10000000, |
| UTP_DEVICE_MANAGEMENT_FUNCTION = 0x20000000, |
| UTP_REQ_DESC_INT_CMD = 0x01000000, |
| }; |
| |
| /* UTP Transfer Request Data Direction (DD) */ |
| enum { |
| UTP_NO_DATA_TRANSFER = 0x00000000, |
| UTP_HOST_TO_DEVICE = 0x02000000, |
| UTP_DEVICE_TO_HOST = 0x04000000, |
| }; |
| |
| /* Overall command status values */ |
| enum { |
| OCS_SUCCESS = 0x0, |
| OCS_INVALID_CMD_TABLE_ATTR = 0x1, |
| OCS_INVALID_PRDT_ATTR = 0x2, |
| OCS_MISMATCH_DATA_BUF_SIZE = 0x3, |
| OCS_MISMATCH_RESP_UPIU_SIZE = 0x4, |
| OCS_PEER_COMM_FAILURE = 0x5, |
| OCS_ABORTED = 0x6, |
| OCS_FATAL_ERROR = 0x7, |
| OCS_INVALID_COMMAND_STATUS = 0x0F, |
| MASK_OCS = 0x0F, |
| }; |
| |
| /* The maximum length of the data byte count field in the PRDT is 256KB */ |
| #define PRDT_DATA_BYTE_COUNT_MAX (256 * 1024) |
| /* The granularity of the data byte count field in the PRDT is 32-bit */ |
| #define PRDT_DATA_BYTE_COUNT_PAD 4 |
| |
| #define GENERAL_UPIU_REQUEST_SIZE (sizeof(struct utp_upiu_req)) |
| #define QUERY_DESC_MAX_SIZE 255 |
| #define QUERY_DESC_MIN_SIZE 2 |
| #define QUERY_DESC_HDR_SIZE 2 |
| #define QUERY_OSF_SIZE (GENERAL_UPIU_REQUEST_SIZE - \ |
| (sizeof(struct utp_upiu_header))) |
| #define RESPONSE_UPIU_SENSE_DATA_LENGTH 18 |
| #define UPIU_HEADER_DWORD(byte3, byte2, byte1, byte0)\ |
| cpu_to_be32((byte3 << 24) | (byte2 << 16) |\ |
| (byte1 << 8) | (byte0)) |
| /* |
| * UFS Protocol Information Unit related definitions |
| */ |
| |
| /* Task management functions */ |
| enum { |
| UFS_ABORT_TASK = 0x01, |
| UFS_ABORT_TASK_SET = 0x02, |
| UFS_CLEAR_TASK_SET = 0x04, |
| UFS_LOGICAL_RESET = 0x08, |
| UFS_QUERY_TASK = 0x80, |
| UFS_QUERY_TASK_SET = 0x81, |
| }; |
| |
| /* UTP UPIU Transaction Codes Initiator to Target */ |
| enum { |
| UPIU_TRANSACTION_NOP_OUT = 0x00, |
| UPIU_TRANSACTION_COMMAND = 0x01, |
| UPIU_TRANSACTION_DATA_OUT = 0x02, |
| UPIU_TRANSACTION_TASK_REQ = 0x04, |
| UPIU_TRANSACTION_QUERY_REQ = 0x16, |
| }; |
| |
| /* UTP UPIU Transaction Codes Target to Initiator */ |
| enum { |
| UPIU_TRANSACTION_NOP_IN = 0x20, |
| UPIU_TRANSACTION_RESPONSE = 0x21, |
| UPIU_TRANSACTION_DATA_IN = 0x22, |
| UPIU_TRANSACTION_TASK_RSP = 0x24, |
| UPIU_TRANSACTION_READY_XFER = 0x31, |
| UPIU_TRANSACTION_QUERY_RSP = 0x36, |
| UPIU_TRANSACTION_REJECT_UPIU = 0x3F, |
| }; |
| |
| /* UPIU Read/Write flags */ |
| enum { |
| UPIU_CMD_FLAGS_NONE = 0x00, |
| UPIU_CMD_FLAGS_WRITE = 0x20, |
| UPIU_CMD_FLAGS_READ = 0x40, |
| }; |
| |
| /* UPIU Task Attributes */ |
| enum { |
| UPIU_TASK_ATTR_SIMPLE = 0x00, |
| UPIU_TASK_ATTR_ORDERED = 0x01, |
| UPIU_TASK_ATTR_HEADQ = 0x02, |
| UPIU_TASK_ATTR_ACA = 0x03, |
| }; |
| |
| /* UPIU Query request function */ |
| enum { |
| UPIU_QUERY_FUNC_STANDARD_READ_REQUEST = 0x01, |
| UPIU_QUERY_FUNC_STANDARD_WRITE_REQUEST = 0x81, |
| }; |
| |
| /* Offset of the response code in the UPIU header */ |
| #define UPIU_RSP_CODE_OFFSET 8 |
| |
| enum { |
| MASK_SCSI_STATUS = 0xFF, |
| MASK_TASK_RESPONSE = 0xFF00, |
| MASK_RSP_UPIU_RESULT = 0xFFFF, |
| MASK_QUERY_DATA_SEG_LEN = 0xFFFF, |
| MASK_RSP_UPIU_DATA_SEG_LEN = 0xFFFF, |
| MASK_RSP_EXCEPTION_EVENT = 0x10000, |
| MASK_TM_SERVICE_RESP = 0xFF, |
| MASK_TM_FUNC = 0xFF, |
| }; |
| |
| /* UTP QUERY Transaction Specific Fields OpCode */ |
| enum query_opcode { |
| UPIU_QUERY_OPCODE_NOP = 0x0, |
| UPIU_QUERY_OPCODE_READ_DESC = 0x1, |
| UPIU_QUERY_OPCODE_WRITE_DESC = 0x2, |
| UPIU_QUERY_OPCODE_READ_ATTR = 0x3, |
| UPIU_QUERY_OPCODE_WRITE_ATTR = 0x4, |
| UPIU_QUERY_OPCODE_READ_FLAG = 0x5, |
| UPIU_QUERY_OPCODE_SET_FLAG = 0x6, |
| UPIU_QUERY_OPCODE_CLEAR_FLAG = 0x7, |
| UPIU_QUERY_OPCODE_TOGGLE_FLAG = 0x8, |
| }; |
| |
| /* Query response result code */ |
| enum { |
| QUERY_RESULT_SUCCESS = 0x00, |
| QUERY_RESULT_NOT_READABLE = 0xF6, |
| QUERY_RESULT_NOT_WRITEABLE = 0xF7, |
| QUERY_RESULT_ALREADY_WRITTEN = 0xF8, |
| QUERY_RESULT_INVALID_LENGTH = 0xF9, |
| QUERY_RESULT_INVALID_VALUE = 0xFA, |
| QUERY_RESULT_INVALID_SELECTOR = 0xFB, |
| QUERY_RESULT_INVALID_INDEX = 0xFC, |
| QUERY_RESULT_INVALID_IDN = 0xFD, |
| QUERY_RESULT_INVALID_OPCODE = 0xFE, |
| QUERY_RESULT_GENERAL_FAILURE = 0xFF, |
| }; |
| |
| enum { |
| UPIU_COMMAND_SET_TYPE_SCSI = 0x0, |
| UPIU_COMMAND_SET_TYPE_UFS = 0x1, |
| UPIU_COMMAND_SET_TYPE_QUERY = 0x2, |
| }; |
| |
| /* Flag idn for Query Requests*/ |
| enum flag_idn { |
| QUERY_FLAG_IDN_FDEVICEINIT = 0x01, |
| QUERY_FLAG_IDN_PERMANENT_WPE = 0x02, |
| QUERY_FLAG_IDN_PWR_ON_WPE = 0x03, |
| QUERY_FLAG_IDN_BKOPS_EN = 0x04, |
| QUERY_FLAG_IDN_LIFE_SPAN_MODE_ENABLE = 0x05, |
| QUERY_FLAG_IDN_PURGE_ENABLE = 0x06, |
| QUERY_FLAG_IDN_RESERVED2 = 0x07, |
| QUERY_FLAG_IDN_FPHYRESOURCEREMOVAL = 0x08, |
| QUERY_FLAG_IDN_BUSY_RTC = 0x09, |
| QUERY_FLAG_IDN_RESERVED3 = 0x0A, |
| QUERY_FLAG_IDN_PERMANENTLY_DISABLE_FW_UPDATE = 0x0B, |
| }; |
| |
| /* Attribute idn for Query requests */ |
| enum attr_idn { |
| QUERY_ATTR_IDN_BOOT_LU_EN = 0x00, |
| QUERY_ATTR_IDN_RESERVED = 0x01, |
| QUERY_ATTR_IDN_POWER_MODE = 0x02, |
| QUERY_ATTR_IDN_ACTIVE_ICC_LVL = 0x03, |
| QUERY_ATTR_IDN_OOO_DATA_EN = 0x04, |
| QUERY_ATTR_IDN_BKOPS_STATUS = 0x05, |
| QUERY_ATTR_IDN_PURGE_STATUS = 0x06, |
| QUERY_ATTR_IDN_MAX_DATA_IN = 0x07, |
| QUERY_ATTR_IDN_MAX_DATA_OUT = 0x08, |
| QUERY_ATTR_IDN_DYN_CAP_NEEDED = 0x09, |
| QUERY_ATTR_IDN_REF_CLK_FREQ = 0x0A, |
| QUERY_ATTR_IDN_CONF_DESC_LOCK = 0x0B, |
| QUERY_ATTR_IDN_MAX_NUM_OF_RTT = 0x0C, |
| QUERY_ATTR_IDN_EE_CONTROL = 0x0D, |
| QUERY_ATTR_IDN_EE_STATUS = 0x0E, |
| QUERY_ATTR_IDN_SECONDS_PASSED = 0x0F, |
| QUERY_ATTR_IDN_CNTX_CONF = 0x10, |
| QUERY_ATTR_IDN_CORR_PRG_BLK_NUM = 0x11, |
| QUERY_ATTR_IDN_RESERVED2 = 0x12, |
| QUERY_ATTR_IDN_RESERVED3 = 0x13, |
| QUERY_ATTR_IDN_FFU_STATUS = 0x14, |
| QUERY_ATTR_IDN_PSA_STATE = 0x15, |
| QUERY_ATTR_IDN_PSA_DATA_SIZE = 0x16, |
| }; |
| |
| /* Descriptor idn for Query requests */ |
| enum desc_idn { |
| QUERY_DESC_IDN_DEVICE = 0x0, |
| QUERY_DESC_IDN_CONFIGURATION = 0x1, |
| QUERY_DESC_IDN_UNIT = 0x2, |
| QUERY_DESC_IDN_RFU_0 = 0x3, |
| QUERY_DESC_IDN_INTERCONNECT = 0x4, |
| QUERY_DESC_IDN_STRING = 0x5, |
| QUERY_DESC_IDN_RFU_1 = 0x6, |
| QUERY_DESC_IDN_GEOMETRY = 0x7, |
| QUERY_DESC_IDN_POWER = 0x8, |
| QUERY_DESC_IDN_HEALTH = 0x9, |
| QUERY_DESC_IDN_MAX, |
| }; |
| |
| enum desc_header_offset { |
| QUERY_DESC_LENGTH_OFFSET = 0x00, |
| QUERY_DESC_DESC_TYPE_OFFSET = 0x01, |
| }; |
| |
| struct ufshcd_sg_entry { |
| __le32 base_addr; |
| __le32 upper_addr; |
| __le32 reserved; |
| __le32 size; |
| }; |
| |
| #define MAX_BUFF 128 |
| /** |
| * struct utp_transfer_cmd_desc - UFS Command Descriptor structure |
| * @command_upiu: Command UPIU Frame address |
| * @response_upiu: Response UPIU Frame address |
| * @prd_table: Physical Region Descriptor |
| */ |
| struct utp_transfer_cmd_desc { |
| u8 command_upiu[ALIGNED_UPIU_SIZE]; |
| u8 response_upiu[ALIGNED_UPIU_SIZE]; |
| struct ufshcd_sg_entry prd_table[MAX_BUFF]; |
| }; |
| |
| /** |
| * struct request_desc_header - Descriptor Header common to both UTRD and UTMRD |
| * @dword0: Descriptor Header DW0 |
| * @dword1: Descriptor Header DW1 |
| * @dword2: Descriptor Header DW2 |
| * @dword3: Descriptor Header DW3 |
| */ |
| struct request_desc_header { |
| __le32 dword_0; |
| __le32 dword_1; |
| __le32 dword_2; |
| __le32 dword_3; |
| }; |
| |
| /** |
| * struct utp_transfer_req_desc - UTRD structure |
| * @header: UTRD header DW-0 to DW-3 |
| * @command_desc_base_addr_lo: UCD base address low DW-4 |
| * @command_desc_base_addr_hi: UCD base address high DW-5 |
| * @response_upiu_length: response UPIU length DW-6 |
| * @response_upiu_offset: response UPIU offset DW-6 |
| * @prd_table_length: Physical region descriptor length DW-7 |
| * @prd_table_offset: Physical region descriptor offset DW-7 |
| */ |
| struct utp_transfer_req_desc { |
| /* DW 0-3 */ |
| struct request_desc_header header; |
| |
| /* DW 4-5*/ |
| __le32 command_desc_base_addr_lo; |
| __le32 command_desc_base_addr_hi; |
| |
| /* DW 6 */ |
| __le16 response_upiu_length; |
| __le16 response_upiu_offset; |
| |
| /* DW 7 */ |
| __le16 prd_table_length; |
| __le16 prd_table_offset; |
| }; |
| |
| /** |
| * struct utp_upiu_header - UPIU header structure |
| * @dword_0: UPIU header DW-0 |
| * @dword_1: UPIU header DW-1 |
| * @dword_2: UPIU header DW-2 |
| */ |
| struct utp_upiu_header { |
| __be32 dword_0; |
| __be32 dword_1; |
| __be32 dword_2; |
| }; |
| |
| /** |
| * struct utp_upiu_query - upiu request buffer structure for |
| * query request. |
| * @opcode: command to perform B-0 |
| * @idn: a value that indicates the particular type of data B-1 |
| * @index: Index to further identify data B-2 |
| * @selector: Index to further identify data B-3 |
| * @reserved_osf: spec reserved field B-4,5 |
| * @length: number of descriptor bytes to read/write B-6,7 |
| * @value: Attribute value to be written DW-5 |
| * @reserved: spec reserved DW-6,7 |
| */ |
| struct utp_upiu_query { |
| __u8 opcode; |
| __u8 idn; |
| __u8 index; |
| __u8 selector; |
| __be16 reserved_osf; |
| __be16 length; |
| __be32 value; |
| __be32 reserved[2]; |
| }; |
| |
| /** |
| * struct utp_upiu_cmd - Command UPIU structure |
| * @data_transfer_len: Data Transfer Length DW-3 |
| * @cdb: Command Descriptor Block CDB DW-4 to DW-7 |
| */ |
| struct utp_upiu_cmd { |
| __be32 exp_data_transfer_len; |
| u8 cdb[UFS_CDB_SIZE]; |
| }; |
| |
| /* |
| * UTMRD structure. |
| */ |
| struct utp_task_req_desc { |
| /* DW 0-3 */ |
| struct request_desc_header header; |
| |
| /* DW 4-11 - Task request UPIU structure */ |
| struct utp_upiu_header req_header; |
| __be32 input_param1; |
| __be32 input_param2; |
| __be32 input_param3; |
| __be32 __reserved1[2]; |
| |
| /* DW 12-19 - Task Management Response UPIU structure */ |
| struct utp_upiu_header rsp_header; |
| __be32 output_param1; |
| __be32 output_param2; |
| __be32 __reserved2[3]; |
| }; |
| |
| /** |
| * struct utp_upiu_req - general upiu request structure |
| * @header:UPIU header structure DW-0 to DW-2 |
| * @sc: fields structure for scsi command DW-3 to DW-7 |
| * @qr: fields structure for query request DW-3 to DW-7 |
| */ |
| struct utp_upiu_req { |
| struct utp_upiu_header header; |
| union { |
| struct utp_upiu_cmd sc; |
| struct utp_upiu_query qr; |
| struct utp_upiu_query tr; |
| /* use utp_upiu_query to host the 4 dwords of uic command */ |
| struct utp_upiu_query uc; |
| }; |
| }; |
| |
| /** |
| * struct utp_cmd_rsp - Response UPIU structure |
| * @residual_transfer_count: Residual transfer count DW-3 |
| * @reserved: Reserved double words DW-4 to DW-7 |
| * @sense_data_len: Sense data length DW-8 U16 |
| * @sense_data: Sense data field DW-8 to DW-12 |
| */ |
| struct utp_cmd_rsp { |
| __be32 residual_transfer_count; |
| __be32 reserved[4]; |
| __be16 sense_data_len; |
| u8 sense_data[RESPONSE_UPIU_SENSE_DATA_LENGTH]; |
| }; |
| |
| /** |
| * struct utp_upiu_rsp - general upiu response structure |
| * @header: UPIU header structure DW-0 to DW-2 |
| * @sr: fields structure for scsi command DW-3 to DW-12 |
| * @qr: fields structure for query request DW-3 to DW-7 |
| */ |
| struct utp_upiu_rsp { |
| struct utp_upiu_header header; |
| union { |
| struct utp_cmd_rsp sr; |
| struct utp_upiu_query qr; |
| }; |
| }; |
| |
| #define MAX_MODEL_LEN 16 |
| /** |
| * ufs_dev_desc - ufs device details from the device descriptor |
| * |
| * @wmanufacturerid: card details |
| * @model: card model |
| */ |
| struct ufs_dev_desc { |
| u16 wmanufacturerid; |
| char model[MAX_MODEL_LEN + 1]; |
| }; |
| |
| /* Device descriptor parameters offsets in bytes*/ |
| enum device_desc_param { |
| DEVICE_DESC_PARAM_LEN = 0x0, |
| DEVICE_DESC_PARAM_TYPE = 0x1, |
| DEVICE_DESC_PARAM_DEVICE_TYPE = 0x2, |
| DEVICE_DESC_PARAM_DEVICE_CLASS = 0x3, |
| DEVICE_DESC_PARAM_DEVICE_SUB_CLASS = 0x4, |
| DEVICE_DESC_PARAM_PRTCL = 0x5, |
| DEVICE_DESC_PARAM_NUM_LU = 0x6, |
| DEVICE_DESC_PARAM_NUM_WLU = 0x7, |
| DEVICE_DESC_PARAM_BOOT_ENBL = 0x8, |
| DEVICE_DESC_PARAM_DESC_ACCSS_ENBL = 0x9, |
| DEVICE_DESC_PARAM_INIT_PWR_MODE = 0xA, |
| DEVICE_DESC_PARAM_HIGH_PR_LUN = 0xB, |
| DEVICE_DESC_PARAM_SEC_RMV_TYPE = 0xC, |
| DEVICE_DESC_PARAM_SEC_LU = 0xD, |
| DEVICE_DESC_PARAM_BKOP_TERM_LT = 0xE, |
| DEVICE_DESC_PARAM_ACTVE_ICC_LVL = 0xF, |
| DEVICE_DESC_PARAM_SPEC_VER = 0x10, |
| DEVICE_DESC_PARAM_MANF_DATE = 0x12, |
| DEVICE_DESC_PARAM_MANF_NAME = 0x14, |
| DEVICE_DESC_PARAM_PRDCT_NAME = 0x15, |
| DEVICE_DESC_PARAM_SN = 0x16, |
| DEVICE_DESC_PARAM_OEM_ID = 0x17, |
| DEVICE_DESC_PARAM_MANF_ID = 0x18, |
| DEVICE_DESC_PARAM_UD_OFFSET = 0x1A, |
| DEVICE_DESC_PARAM_UD_LEN = 0x1B, |
| DEVICE_DESC_PARAM_RTT_CAP = 0x1C, |
| DEVICE_DESC_PARAM_FRQ_RTC = 0x1D, |
| DEVICE_DESC_PARAM_UFS_FEAT = 0x1F, |
| DEVICE_DESC_PARAM_FFU_TMT = 0x20, |
| DEVICE_DESC_PARAM_Q_DPTH = 0x21, |
| DEVICE_DESC_PARAM_DEV_VER = 0x22, |
| DEVICE_DESC_PARAM_NUM_SEC_WPA = 0x24, |
| DEVICE_DESC_PARAM_PSA_MAX_DATA = 0x25, |
| DEVICE_DESC_PARAM_PSA_TMT = 0x29, |
| DEVICE_DESC_PARAM_PRDCT_REV = 0x2A, |
| }; |
| |
| struct ufs_hba; |
| |
| enum { |
| UFSHCD_MAX_CHANNEL = 0, |
| UFSHCD_MAX_ID = 1, |
| }; |
| |
| enum dev_cmd_type { |
| DEV_CMD_TYPE_NOP = 0x0, |
| DEV_CMD_TYPE_QUERY = 0x1, |
| }; |
| |
| /** |
| * struct uic_command - UIC command structure |
| * @command: UIC command |
| * @argument1: UIC command argument 1 |
| * @argument2: UIC command argument 2 |
| * @argument3: UIC command argument 3 |
| * @cmd_active: Indicate if UIC command is outstanding |
| * @result: UIC command result |
| * @done: UIC command completion |
| */ |
| struct uic_command { |
| u32 command; |
| u32 argument1; |
| u32 argument2; |
| u32 argument3; |
| int cmd_active; |
| int result; |
| }; |
| |
| /* GenSelectorIndex calculation macros for M-PHY attributes */ |
| #define UIC_ARG_MPHY_TX_GEN_SEL_INDEX(lane) (lane) |
| #define UIC_ARG_MPHY_RX_GEN_SEL_INDEX(lane) (PA_MAXDATALANES + (lane)) |
| |
| #define UIC_ARG_MIB_SEL(attr, sel) ((((attr) & 0xFFFF) << 16) |\ |
| ((sel) & 0xFFFF)) |
| #define UIC_ARG_MIB(attr) UIC_ARG_MIB_SEL(attr, 0) |
| #define UIC_ARG_ATTR_TYPE(t) (((t) & 0xFF) << 16) |
| #define UIC_GET_ATTR_ID(v) (((v) >> 16) & 0xFFFF) |
| |
| /* Link Status*/ |
| enum link_status { |
| UFSHCD_LINK_IS_DOWN = 1, |
| UFSHCD_LINK_IS_UP = 2, |
| }; |
| |
| #define UIC_ARG_MIB_SEL(attr, sel) ((((attr) & 0xFFFF) << 16) |\ |
| ((sel) & 0xFFFF)) |
| #define UIC_ARG_MIB(attr) UIC_ARG_MIB_SEL(attr, 0) |
| #define UIC_ARG_ATTR_TYPE(t) (((t) & 0xFF) << 16) |
| #define UIC_GET_ATTR_ID(v) (((v) >> 16) & 0xFFFF) |
| |
| /* UIC Commands */ |
| enum uic_cmd_dme { |
| UIC_CMD_DME_GET = 0x01, |
| UIC_CMD_DME_SET = 0x02, |
| UIC_CMD_DME_PEER_GET = 0x03, |
| UIC_CMD_DME_PEER_SET = 0x04, |
| UIC_CMD_DME_POWERON = 0x10, |
| UIC_CMD_DME_POWEROFF = 0x11, |
| UIC_CMD_DME_ENABLE = 0x12, |
| UIC_CMD_DME_RESET = 0x14, |
| UIC_CMD_DME_END_PT_RST = 0x15, |
| UIC_CMD_DME_LINK_STARTUP = 0x16, |
| UIC_CMD_DME_HIBER_ENTER = 0x17, |
| UIC_CMD_DME_HIBER_EXIT = 0x18, |
| UIC_CMD_DME_TEST_MODE = 0x1A, |
| }; |
| |
| /* UIC Config result code / Generic error code */ |
| enum { |
| UIC_CMD_RESULT_SUCCESS = 0x00, |
| UIC_CMD_RESULT_INVALID_ATTR = 0x01, |
| UIC_CMD_RESULT_FAILURE = 0x01, |
| UIC_CMD_RESULT_INVALID_ATTR_VALUE = 0x02, |
| UIC_CMD_RESULT_READ_ONLY_ATTR = 0x03, |
| UIC_CMD_RESULT_WRITE_ONLY_ATTR = 0x04, |
| UIC_CMD_RESULT_BAD_INDEX = 0x05, |
| UIC_CMD_RESULT_LOCKED_ATTR = 0x06, |
| UIC_CMD_RESULT_BAD_TEST_FEATURE_INDEX = 0x07, |
| UIC_CMD_RESULT_PEER_COMM_FAILURE = 0x08, |
| UIC_CMD_RESULT_BUSY = 0x09, |
| UIC_CMD_RESULT_DME_FAILURE = 0x0A, |
| }; |
| |
| #define MASK_UIC_COMMAND_RESULT 0xFF |
| |
| /* Host <-> Device UniPro Link state */ |
| enum uic_link_state { |
| UIC_LINK_OFF_STATE = 0, /* Link powered down or disabled */ |
| UIC_LINK_ACTIVE_STATE = 1, /* Link is in Fast/Slow/Sleep state */ |
| UIC_LINK_HIBERN8_STATE = 2, /* Link is in Hibernate state */ |
| }; |
| |
| /* UIC command interfaces for DME primitives */ |
| #define DME_LOCAL 0 |
| #define DME_PEER 1 |
| #define ATTR_SET_NOR 0 /* NORMAL */ |
| #define ATTR_SET_ST 1 /* STATIC */ |
| |
| int ufshcd_dme_set_attr(struct ufs_hba *hba, u32 attr_sel, |
| u8 attr_set, u32 mib_val, u8 peer); |
| int ufshcd_dme_get_attr(struct ufs_hba *hba, u32 attr_sel, |
| u32 *mib_val, u8 peer); |
| |
| static inline int ufshcd_dme_set(struct ufs_hba *hba, u32 attr_sel, |
| u32 mib_val) |
| { |
| return ufshcd_dme_set_attr(hba, attr_sel, ATTR_SET_NOR, |
| mib_val, DME_LOCAL); |
| } |
| |
| static inline int ufshcd_dme_get(struct ufs_hba *hba, |
| u32 attr_sel, u32 *mib_val) |
| { |
| return ufshcd_dme_get_attr(hba, attr_sel, mib_val, DME_LOCAL); |
| } |
| |
| static inline int ufshcd_dme_peer_get(struct ufs_hba *hba, |
| u32 attr_sel, u32 *mib_val) |
| { |
| return ufshcd_dme_get_attr(hba, attr_sel, mib_val, DME_PEER); |
| } |
| |
| static inline int ufshcd_dme_peer_set(struct ufs_hba *hba, u32 attr_sel, |
| u32 mib_val) |
| { |
| return ufshcd_dme_set_attr(hba, attr_sel, ATTR_SET_NOR, |
| mib_val, DME_PEER); |
| } |
| |
| /** |
| * struct ufs_query_req - parameters for building a query request |
| * @query_func: UPIU header query function |
| * @upiu_req: the query request data |
| */ |
| struct ufs_query_req { |
| u8 query_func; |
| struct utp_upiu_query upiu_req; |
| }; |
| |
| /** |
| * struct ufs_query_resp - UPIU QUERY |
| * @response: device response code |
| * @upiu_res: query response data |
| */ |
| struct ufs_query_res { |
| u8 response; |
| struct utp_upiu_query upiu_res; |
| }; |
| |
| /** |
| * struct ufs_query - holds relevant data structures for query request |
| * @request: request upiu and function |
| * @descriptor: buffer for sending/receiving descriptor |
| * @response: response upiu and response |
| */ |
| struct ufs_query { |
| struct ufs_query_req request; |
| u8 *descriptor; |
| struct ufs_query_res response; |
| }; |
| |
| /** |
| * struct ufs_dev_cmd - all assosiated fields with device management commands |
| * @type: device management command type - Query, NOP OUT |
| * @tag_wq: wait queue until free command slot is available |
| */ |
| struct ufs_dev_cmd { |
| enum dev_cmd_type type; |
| struct ufs_query query; |
| }; |
| |
| struct ufs_hba_ops { |
| int (*init)(struct ufs_hba *hba); |
| int (*get_max_pwr_mode)(struct ufs_hba *hba, |
| struct ufs_pwr_mode_info *max_pwr_info); |
| int (*hce_enable_notify)(struct ufs_hba *hba, |
| enum ufs_notify_change_status); |
| int (*link_startup_notify)(struct ufs_hba *hba, |
| enum ufs_notify_change_status); |
| int (*phy_initialization)(struct ufs_hba *hba); |
| int (*device_reset)(struct ufs_hba *hba); |
| }; |
| |
| enum ufshcd_quirks { |
| /* Interrupt aggregation support is broken */ |
| UFSHCD_QUIRK_BROKEN_INTR_AGGR = 1 << 0, |
| |
| /* |
| * delay before each dme command is required as the unipro |
| * layer has shown instabilities |
| */ |
| UFSHCD_QUIRK_DELAY_BEFORE_DME_CMDS = 1 << 1, |
| |
| /* |
| * If UFS host controller is having issue in processing LCC (Line |
| * Control Command) coming from device then enable this quirk. |
| * When this quirk is enabled, host controller driver should disable |
| * the LCC transmission on UFS device (by clearing TX_LCC_ENABLE |
| * attribute of device to 0). |
| */ |
| UFSHCD_QUIRK_BROKEN_LCC = 1 << 2, |
| |
| /* |
| * The attribute PA_RXHSUNTERMCAP specifies whether or not the |
| * inbound Link supports unterminated line in HS mode. Setting this |
| * attribute to 1 fixes moving to HS gear. |
| */ |
| UFSHCD_QUIRK_BROKEN_PA_RXHSUNTERMCAP = 1 << 3, |
| |
| /* |
| * This quirk needs to be enabled if the host controller only allows |
| * accessing the peer dme attributes in AUTO mode (FAST AUTO or |
| * SLOW AUTO). |
| */ |
| UFSHCD_QUIRK_DME_PEER_ACCESS_AUTO_MODE = 1 << 4, |
| |
| /* |
| * This quirk needs to be enabled if the host controller doesn't |
| * advertise the correct version in UFS_VER register. If this quirk |
| * is enabled, standard UFS host driver will call the vendor specific |
| * ops (get_ufs_hci_version) to get the correct version. |
| */ |
| UFSHCD_QUIRK_BROKEN_UFS_HCI_VERSION = 1 << 5, |
| |
| /* |
| * Clear handling for transfer/task request list is just opposite. |
| */ |
| UFSHCI_QUIRK_BROKEN_REQ_LIST_CLR = 1 << 6, |
| |
| /* |
| * This quirk needs to be enabled if host controller doesn't allow |
| * that the interrupt aggregation timer and counter are reset by s/w. |
| */ |
| UFSHCI_QUIRK_SKIP_RESET_INTR_AGGR = 1 << 7, |
| |
| /* |
| * This quirks needs to be enabled if host controller cannot be |
| * enabled via HCE register. |
| */ |
| UFSHCI_QUIRK_BROKEN_HCE = 1 << 8, |
| |
| /* |
| * This quirk needs to be enabled if the host controller regards |
| * resolution of the values of PRDTO and PRDTL in UTRD as byte. |
| */ |
| UFSHCD_QUIRK_PRDT_BYTE_GRAN = 1 << 9, |
| |
| /* |
| * This quirk needs to be enabled if the host controller reports |
| * OCS FATAL ERROR with device error through sense data |
| */ |
| UFSHCD_QUIRK_BROKEN_OCS_FATAL_ERROR = 1 << 10, |
| |
| /* |
| * This quirk needs to be enabled if the host controller has |
| * auto-hibernate capability but it doesn't work. |
| */ |
| UFSHCD_QUIRK_BROKEN_AUTO_HIBERN8 = 1 << 11, |
| |
| /* |
| * This quirk needs to disable manual flush for write booster |
| */ |
| UFSHCI_QUIRK_SKIP_MANUAL_WB_FLUSH_CTRL = 1 << 12, |
| |
| /* |
| * This quirk needs to disable unipro timeout values |
| * before power mode change |
| */ |
| UFSHCD_QUIRK_SKIP_DEF_UNIPRO_TIMEOUT_SETTING = 1 << 13, |
| |
| /* |
| * This quirk needs to be enabled if the host controller does not |
| * support UIC command |
| */ |
| UFSHCD_QUIRK_BROKEN_UIC_CMD = 1 << 15, |
| |
| /* |
| * This quirk needs to be enabled if the host controller cannot |
| * support physical host configuration. |
| */ |
| UFSHCD_QUIRK_SKIP_PH_CONFIGURATION = 1 << 16, |
| |
| /* |
| * This quirk needs to be enabled if the host controller has |
| * 64-bit addressing supported capability but it doesn't work. |
| */ |
| UFSHCD_QUIRK_BROKEN_64BIT_ADDRESS = 1 << 17, |
| |
| /* |
| * This quirk needs to be enabled if the host controller has |
| * auto-hibernate capability but it's FASTAUTO only. |
| */ |
| UFSHCD_QUIRK_HIBERN_FASTAUTO = 1 << 18, |
| |
| /* |
| * This quirk needs to be enabled if the host controller needs |
| * to reinit the device after switching to maximum gear. |
| */ |
| UFSHCD_QUIRK_REINIT_AFTER_MAX_GEAR_SWITCH = 1 << 19, |
| |
| /* |
| * Some host raises interrupt (per queue) in addition to |
| * CQES (traditional) when ESI is disabled. |
| * Enable this quirk will disable CQES and use per queue interrupt. |
| */ |
| UFSHCD_QUIRK_MCQ_BROKEN_INTR = 1 << 20, |
| |
| /* |
| * Some host does not implement SQ Run Time Command (SQRTC) register |
| * thus need this quirk to skip related flow. |
| */ |
| UFSHCD_QUIRK_MCQ_BROKEN_RTC = 1 << 21, |
| |
| /* |
| * This quirk needs to be enabled if the host controller supports inline |
| * encryption but it needs to initialize the crypto capabilities in a |
| * nonstandard way and/or needs to override blk_crypto_ll_ops. If |
| * enabled, the standard code won't initialize the blk_crypto_profile; |
| * ufs_hba_variant_ops::init() must do it instead. |
| */ |
| UFSHCD_QUIRK_CUSTOM_CRYPTO_PROFILE = 1 << 22, |
| |
| /* |
| * This quirk needs to be enabled if the host controller supports inline |
| * encryption but does not support the CRYPTO_GENERAL_ENABLE bit, i.e. |
| * host controller initialization fails if that bit is set. |
| */ |
| UFSHCD_QUIRK_BROKEN_CRYPTO_ENABLE = 1 << 23, |
| |
| /* |
| * This quirk needs to be enabled if the host controller driver copies |
| * cryptographic keys into the PRDT in order to send them to hardware, |
| * and therefore the PRDT should be zeroized after each request (as per |
| * the standard best practice for managing keys). |
| */ |
| UFSHCD_QUIRK_KEYS_IN_PRDT = 1 << 24, |
| |
| /* |
| * This quirk indicates that the controller reports the value 1 (not |
| * supported) in the Legacy Single DoorBell Support (LSDBS) bit of the |
| * Controller Capabilities register although it supports the legacy |
| * single doorbell mode. |
| */ |
| UFSHCD_QUIRK_BROKEN_LSDBS_CAP = 1 << 25, |
| }; |
| |
| struct ufs_hba { |
| struct udevice *dev; |
| void __iomem *mmio_base; |
| struct ufs_hba_ops *ops; |
| struct ufs_desc_size desc_size; |
| u32 capabilities; |
| u32 version; |
| u32 intr_mask; |
| enum ufshcd_quirks quirks; |
| |
| /* Virtual memory reference */ |
| struct utp_transfer_cmd_desc *ucdl; |
| struct utp_transfer_req_desc *utrdl; |
| /* TODO: Add Task Manegement Support */ |
| struct utp_task_req_desc *utmrdl; |
| |
| struct utp_upiu_req *ucd_req_ptr; |
| struct utp_upiu_rsp *ucd_rsp_ptr; |
| struct ufshcd_sg_entry *ucd_prdt_ptr; |
| |
| /* Power Mode information */ |
| enum ufs_dev_pwr_mode curr_dev_pwr_mode; |
| struct ufs_pa_layer_attr pwr_info; |
| struct ufs_pwr_mode_info max_pwr_info; |
| |
| struct ufs_dev_cmd dev_cmd; |
| }; |
| |
| static inline int ufshcd_ops_init(struct ufs_hba *hba) |
| { |
| if (hba->ops && hba->ops->init) |
| return hba->ops->init(hba); |
| |
| return 0; |
| } |
| |
| static inline int ufshcd_ops_get_max_pwr_mode(struct ufs_hba *hba, |
| struct ufs_pwr_mode_info *max_pwr_info) |
| { |
| if (hba->ops && hba->ops->get_max_pwr_mode) |
| return hba->ops->get_max_pwr_mode(hba, max_pwr_info); |
| |
| return 0; |
| } |
| |
| static inline int ufshcd_ops_hce_enable_notify(struct ufs_hba *hba, |
| bool status) |
| { |
| if (hba->ops && hba->ops->hce_enable_notify) |
| return hba->ops->hce_enable_notify(hba, status); |
| |
| return 0; |
| } |
| |
| static inline int ufshcd_ops_link_startup_notify(struct ufs_hba *hba, |
| bool status) |
| { |
| if (hba->ops && hba->ops->link_startup_notify) |
| return hba->ops->link_startup_notify(hba, status); |
| |
| return 0; |
| } |
| |
| static inline int ufshcd_vops_device_reset(struct ufs_hba *hba) |
| { |
| if (hba->ops && hba->ops->device_reset) |
| return hba->ops->device_reset(hba); |
| |
| return 0; |
| } |
| |
| /* Controller UFSHCI version */ |
| enum { |
| UFSHCI_VERSION_10 = 0x00010000, /* 1.0 */ |
| UFSHCI_VERSION_11 = 0x00010100, /* 1.1 */ |
| UFSHCI_VERSION_20 = 0x00000200, /* 2.0 */ |
| UFSHCI_VERSION_21 = 0x00000210, /* 2.1 */ |
| UFSHCI_VERSION_30 = 0x00000300, /* 3.0 */ |
| UFSHCI_VERSION_31 = 0x00000310, /* 3.1 */ |
| UFSHCI_VERSION_40 = 0x00000400, /* 4.0 */ |
| }; |
| |
| /* Interrupt disable masks */ |
| enum { |
| /* Interrupt disable mask for UFSHCI v1.0 */ |
| INTERRUPT_MASK_ALL_VER_10 = 0x30FFF, |
| INTERRUPT_MASK_RW_VER_10 = 0x30000, |
| |
| /* Interrupt disable mask for UFSHCI v1.1 */ |
| INTERRUPT_MASK_ALL_VER_11 = 0x31FFF, |
| |
| /* Interrupt disable mask for UFSHCI v2.1 */ |
| INTERRUPT_MASK_ALL_VER_21 = 0x71FFF, |
| }; |
| |
| /* UFSHCI Registers */ |
| enum { |
| REG_CONTROLLER_CAPABILITIES = 0x00, |
| REG_UFS_VERSION = 0x08, |
| REG_CONTROLLER_DEV_ID = 0x10, |
| REG_CONTROLLER_PROD_ID = 0x14, |
| REG_AUTO_HIBERNATE_IDLE_TIMER = 0x18, |
| REG_INTERRUPT_STATUS = 0x20, |
| REG_INTERRUPT_ENABLE = 0x24, |
| REG_CONTROLLER_STATUS = 0x30, |
| REG_CONTROLLER_ENABLE = 0x34, |
| REG_UIC_ERROR_CODE_PHY_ADAPTER_LAYER = 0x38, |
| REG_UIC_ERROR_CODE_DATA_LINK_LAYER = 0x3C, |
| REG_UIC_ERROR_CODE_NETWORK_LAYER = 0x40, |
| REG_UIC_ERROR_CODE_TRANSPORT_LAYER = 0x44, |
| REG_UIC_ERROR_CODE_DME = 0x48, |
| REG_UTP_TRANSFER_REQ_INT_AGG_CONTROL = 0x4C, |
| REG_UTP_TRANSFER_REQ_LIST_BASE_L = 0x50, |
| REG_UTP_TRANSFER_REQ_LIST_BASE_H = 0x54, |
| REG_UTP_TRANSFER_REQ_DOOR_BELL = 0x58, |
| REG_UTP_TRANSFER_REQ_LIST_CLEAR = 0x5C, |
| REG_UTP_TRANSFER_REQ_LIST_RUN_STOP = 0x60, |
| REG_UTP_TASK_REQ_LIST_BASE_L = 0x70, |
| REG_UTP_TASK_REQ_LIST_BASE_H = 0x74, |
| REG_UTP_TASK_REQ_DOOR_BELL = 0x78, |
| REG_UTP_TASK_REQ_LIST_CLEAR = 0x7C, |
| REG_UTP_TASK_REQ_LIST_RUN_STOP = 0x80, |
| REG_UIC_COMMAND = 0x90, |
| REG_UIC_COMMAND_ARG_1 = 0x94, |
| REG_UIC_COMMAND_ARG_2 = 0x98, |
| REG_UIC_COMMAND_ARG_3 = 0x9C, |
| |
| UFSHCI_REG_SPACE_SIZE = 0xA0, |
| |
| REG_UFS_CCAP = 0x100, |
| REG_UFS_CRYPTOCAP = 0x104, |
| |
| UFSHCI_CRYPTO_REG_SPACE_SIZE = 0x400, |
| }; |
| |
| /* Controller capability masks */ |
| enum { |
| MASK_TRANSFER_REQUESTS_SLOTS = 0x0000001F, |
| MASK_TASK_MANAGEMENT_REQUEST_SLOTS = 0x00070000, |
| MASK_AUTO_HIBERN8_SUPPORT = 0x00800000, |
| MASK_64_ADDRESSING_SUPPORT = 0x01000000, |
| MASK_OUT_OF_ORDER_DATA_DELIVERY_SUPPORT = 0x02000000, |
| MASK_UIC_DME_TEST_MODE_SUPPORT = 0x04000000, |
| }; |
| |
| /* Interrupt Status 20h */ |
| #define UTP_TRANSFER_REQ_COMPL 0x1 |
| #define UIC_DME_END_PT_RESET 0x2 |
| #define UIC_ERROR 0x4 |
| #define UIC_TEST_MODE 0x8 |
| #define UIC_POWER_MODE 0x10 |
| #define UIC_HIBERNATE_EXIT 0x20 |
| #define UIC_HIBERNATE_ENTER 0x40 |
| #define UIC_LINK_LOST 0x80 |
| #define UIC_LINK_STARTUP 0x100 |
| #define UTP_TASK_REQ_COMPL 0x200 |
| #define UIC_COMMAND_COMPL 0x400 |
| #define DEVICE_FATAL_ERROR 0x800 |
| #define CONTROLLER_FATAL_ERROR 0x10000 |
| #define SYSTEM_BUS_FATAL_ERROR 0x20000 |
| |
| #define UFSHCD_UIC_PWR_MASK (UIC_HIBERNATE_ENTER |\ |
| UIC_HIBERNATE_EXIT |\ |
| UIC_POWER_MODE) |
| |
| #define UFSHCD_UIC_MASK (UIC_COMMAND_COMPL | UIC_POWER_MODE) |
| |
| #define UFSHCD_ERROR_MASK (UIC_ERROR |\ |
| DEVICE_FATAL_ERROR |\ |
| CONTROLLER_FATAL_ERROR |\ |
| SYSTEM_BUS_FATAL_ERROR) |
| |
| #define INT_FATAL_ERRORS (DEVICE_FATAL_ERROR |\ |
| CONTROLLER_FATAL_ERROR |\ |
| SYSTEM_BUS_FATAL_ERROR) |
| |
| /* Host Controller Enable 0x34h */ |
| #define CONTROLLER_ENABLE 0x1 |
| #define CONTROLLER_DISABLE 0x0 |
| /* HCS - Host Controller Status 30h */ |
| #define DEVICE_PRESENT 0x1 |
| #define UTP_TRANSFER_REQ_LIST_READY 0x2 |
| #define UTP_TASK_REQ_LIST_READY 0x4 |
| #define UIC_COMMAND_READY 0x8 |
| #define HOST_ERROR_INDICATOR 0x10 |
| #define DEVICE_ERROR_INDICATOR 0x20 |
| #define UIC_POWER_MODE_CHANGE_REQ_STATUS_MASK UFS_MASK(0x7, 8) |
| |
| #define UFSHCD_STATUS_READY (UTP_TRANSFER_REQ_LIST_READY |\ |
| UTP_TASK_REQ_LIST_READY |\ |
| UIC_COMMAND_READY) |
| |
| enum { |
| PWR_OK = 0x0, |
| PWR_LOCAL = 0x01, |
| PWR_REMOTE = 0x02, |
| PWR_BUSY = 0x03, |
| PWR_ERROR_CAP = 0x04, |
| PWR_FATAL_ERROR = 0x05, |
| }; |
| |
| /* UICCMD - UIC Command */ |
| #define COMMAND_OPCODE_MASK 0xFF |
| #define GEN_SELECTOR_INDEX_MASK 0xFFFF |
| |
| #define MIB_ATTRIBUTE_MASK UFS_MASK(0xFFFF, 16) |
| #define RESET_LEVEL 0xFF |
| |
| #define ATTR_SET_TYPE_MASK UFS_MASK(0xFF, 16) |
| #define CFG_RESULT_CODE_MASK 0xFF |
| #define GENERIC_ERROR_CODE_MASK 0xFF |
| |
| #define ufshcd_writel(hba, val, reg) \ |
| writel((val), (hba)->mmio_base + (reg)) |
| #define ufshcd_readl(hba, reg) \ |
| readl((hba)->mmio_base + (reg)) |
| |
| /** |
| * ufshcd_rmwl - perform read/modify/write for a controller register |
| * @hba: per adapter instance |
| * @mask: mask to apply on read value |
| * @val: actual value to write |
| * @reg: register address |
| */ |
| static inline void ufshcd_rmwl(struct ufs_hba *hba, u32 mask, u32 val, u32 reg) |
| { |
| u32 tmp; |
| |
| tmp = ufshcd_readl(hba, reg); |
| tmp &= ~mask; |
| tmp |= (val & mask); |
| ufshcd_writel(hba, tmp, reg); |
| } |
| |
| /* UTRLRSR - UTP Transfer Request Run-Stop Register 60h */ |
| #define UTP_TRANSFER_REQ_LIST_RUN_STOP_BIT 0x1 |
| |
| /* UTMRLRSR - UTP Task Management Request Run-Stop Register 80h */ |
| #define UTP_TASK_REQ_LIST_RUN_STOP_BIT 0x1 |
| |
| int ufshcd_probe(struct udevice *dev, struct ufs_hba_ops *hba_ops); |
| |
| #endif |