include/configs/MPC8313ERDB.h - filogic/uboot - Gitiles

 /*
  * Copyright (C) Freescale Semiconductor, Inc. 2006.
  *
  * See file CREDITS for list of people who contributed to this
  * project.
  *
  * This program is free software; you can redistribute it and/or
  * modify it under the terms of the GNU General Public License as
  * published by the Free Software Foundation; either version 2 of
  * the License, or (at your option) any later version.
  *
  * This program is distributed in the hope that it will be useful,
  * but WITHOUT ANY WARRANTY; without even the implied warranty of
  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
  * GNU General Public License for more details.
  *
  * You should have received a copy of the GNU General Public License
  * along with this program; if not, write to the Free Software
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
  * MA 02111-1307 USA
  */
 /*
  * mpc8313epb board configuration file
  */

 #ifndef __CONFIG_H
 #define __CONFIG_H

 /*
  * High Level Configuration Options
  */
 #define CONFIG_E300		1
 #define CONFIG_MPC83XX		1
 #define CONFIG_MPC831X		1
 #define CONFIG_MPC8313		1
 #define CONFIG_MPC8313ERDB	1

 #define CONFIG_PCI
 #define CONFIG_83XX_GENERIC_PCI

 #define CONFIG_MISC_INIT_R

 /*
  * On-board devices
  *
  * TSEC1 is VSC switch
  * TSEC2 is SoC TSEC
  */
 #define CONFIG_VSC7385_ENET
 #define CONFIG_TSEC2

 #ifdef CFG_66MHZ
 #define CONFIG_83XX_CLKIN	66666667	/* in Hz */
 #elif defined(CFG_33MHZ)
 #define CONFIG_83XX_CLKIN	33333333	/* in Hz */
 #else
 #error Unknown oscillator frequency.
 #endif

 #define CONFIG_SYS_CLK_FREQ	CONFIG_83XX_CLKIN

 #define CONFIG_BOARD_EARLY_INIT_F		/* call board_pre_init */

 #define CFG_IMMR		0xE0000000

 #define CFG_MEMTEST_START	0x00001000
 #define CFG_MEMTEST_END		0x07f00000

 /* Early revs of this board will lock up hard when attempting
  * to access the PMC registers, unless a JTAG debugger is
  * connected, or some resistor modifications are made.
  */
 #define CFG_8313ERDB_BROKEN_PMC 1

 #define CFG_ACR_PIPE_DEP	3	/* Arbiter pipeline depth (0-3) */
 #define CFG_ACR_RPTCNT		3	/* Arbiter repeat count (0-7) */

 /*
  * Device configurations
  */

 /* Vitesse 7385 */

 #ifdef CONFIG_VSC7385_ENET

 #define CONFIG_TSEC1

 /* The flash address and size of the VSC7385 firmware image */
 #define CONFIG_VSC7385_IMAGE		0xFE7FE000
 #define CONFIG_VSC7385_IMAGE_SIZE	8192

 #endif

 /*
  * DDR Setup
  */
 #define CFG_DDR_BASE		0x00000000	/* DDR is system memory*/
 #define CFG_SDRAM_BASE		CFG_DDR_BASE
 #define CFG_DDR_SDRAM_BASE	CFG_DDR_BASE

 /*
  * Manually set up DDR parameters, as this board does not
  * seem to have the SPD connected to I2C.
  */
 #define CFG_DDR_SIZE		128		/* MB */
 #define CFG_DDR_CONFIG		( CSCONFIG_EN \
 				| 0x00010000 /* TODO */ \
 				| CSCONFIG_ROW_BIT_13 | CSCONFIG_COL_BIT_10 )
 				/* 0x80010102 */

 #define CFG_DDR_TIMING_3	0x00000000
 #define CFG_DDR_TIMING_0	( ( 0 << TIMING_CFG0_RWT_SHIFT ) \
 				| ( 0 << TIMING_CFG0_WRT_SHIFT ) \
 				| ( 0 << TIMING_CFG0_RRT_SHIFT ) \
 				| ( 0 << TIMING_CFG0_WWT_SHIFT ) \
 				| ( 2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT ) \
 				| ( 2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT ) \
 				| ( 8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT ) \
 				| ( 2 << TIMING_CFG0_MRS_CYC_SHIFT ) )
 				/* 0x00220802 */
 #define CFG_DDR_TIMING_1	( ( 3 << TIMING_CFG1_PRETOACT_SHIFT ) \
 				| ( 8 << TIMING_CFG1_ACTTOPRE_SHIFT ) \
 				| ( 3 << TIMING_CFG1_ACTTORW_SHIFT ) \
 				| ( 5 << TIMING_CFG1_CASLAT_SHIFT ) \
 				| (10 << TIMING_CFG1_REFREC_SHIFT ) \
 				| ( 3 << TIMING_CFG1_WRREC_SHIFT ) \
 				| ( 2 << TIMING_CFG1_ACTTOACT_SHIFT ) \
 				| ( 2 << TIMING_CFG1_WRTORD_SHIFT ) )
 				/* 0x3835a322 */
 #define CFG_DDR_TIMING_2	( ( 1 << TIMING_CFG2_ADD_LAT_SHIFT ) \
 				| ( 5 << TIMING_CFG2_CPO_SHIFT ) \
 				| ( 2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT ) \
 				| ( 2 << TIMING_CFG2_RD_TO_PRE_SHIFT ) \
 				| ( 2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT ) \
 				| ( 3 << TIMING_CFG2_CKE_PLS_SHIFT ) \
 				| ( 6 << TIMING_CFG2_FOUR_ACT_SHIFT) )
 				/* 0x129048c6 */ /* P9-45,may need tuning */
 #define CFG_DDR_INTERVAL	( ( 1296 << SDRAM_INTERVAL_REFINT_SHIFT ) \
 				| ( 1280 << SDRAM_INTERVAL_BSTOPRE_SHIFT ) )
 				/* 0x05100500 */
 #if defined(CONFIG_DDR_2T_TIMING)
 #define CFG_SDRAM_CFG		( SDRAM_CFG_SREN \
 				| SDRAM_CFG_SDRAM_TYPE_DDR2 \
 				| SDRAM_CFG_2T_EN \
 				| SDRAM_CFG_DBW_32 )
 #else
 #define CFG_SDRAM_CFG		( SDRAM_CFG_SREN \
 				| SDRAM_CFG_SDRAM_TYPE_DDR2 \
 				| SDRAM_CFG_32_BE )
 				/* 0x43080000 */
 #endif
 #define CFG_SDRAM_CFG2		0x00401000;
 /* set burst length to 8 for 32-bit data path */
 #define CFG_DDR_MODE		( ( 0x4448 << SDRAM_MODE_ESD_SHIFT ) \
 				| ( 0x0632 << SDRAM_MODE_SD_SHIFT ) )
 				/* 0x44480632 */
 #define CFG_DDR_MODE_2		0x8000C000;

 #define CFG_DDR_CLK_CNTL	DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
 				/*0x02000000*/
 #define CFG_DDRCDR_VALUE	( DDRCDR_EN \
 				| DDRCDR_PZ_NOMZ \
 				| DDRCDR_NZ_NOMZ \
 				| DDRCDR_M_ODR )

 /*
  * FLASH on the Local Bus
  */
 #define CFG_FLASH_CFI				/* use the Common Flash Interface */
 #define CFG_FLASH_CFI_DRIVER			/* use the CFI driver */
 #define CFG_FLASH_BASE		0xFE000000	/* start of FLASH   */
 #define CFG_FLASH_SIZE		8		/* flash size in MB */
 #define CFG_FLASH_EMPTY_INFO			/* display empty sectors */
 #define CFG_FLASH_USE_BUFFER_WRITE		/* buffer up multiple bytes */

 #define CFG_BR0_PRELIM		(CFG_FLASH_BASE |	/* flash Base address */ \
 				(2 << BR_PS_SHIFT) |	/* 16 bit port size */ \
 				BR_V)			/* valid */
 #define CFG_OR0_PRELIM		( 0xFF000000		/* 16 MByte */ \
 				| OR_GPCM_XACS \
 				| OR_GPCM_SCY_9 \
 				| OR_GPCM_EHTR \
 				| OR_GPCM_EAD )
 				/* 0xFF006FF7	TODO SLOW 16 MB flash size */
 #define CFG_LBLAWBAR0_PRELIM	CFG_FLASH_BASE	/* window base at flash base */
 #define CFG_LBLAWAR0_PRELIM	0x80000017	/* 16 MB window size */

 #define CFG_MAX_FLASH_BANKS	1		/* number of banks */
 #define CFG_MAX_FLASH_SECT	135		/* sectors per device */

 #define CFG_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
 #define CFG_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */

 #define CFG_MONITOR_BASE	TEXT_BASE	/* start of monitor */

 #if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
 #define CFG_RAMBOOT
 #endif

 #define CFG_INIT_RAM_LOCK	1
 #define CFG_INIT_RAM_ADDR	0xFD000000	/* Initial RAM address */
 #define CFG_INIT_RAM_END	0x1000		/* End of used area in RAM*/

 #define CFG_GBL_DATA_SIZE	0x100		/* num bytes initial data */
 #define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
 #define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET

 /* CFG_MONITOR_LEN must be a multiple of CFG_ENV_SECT_SIZE */
 #define CFG_MONITOR_LEN		(256 * 1024)	/* Reserve 256 kB for Mon */
 #define CFG_MALLOC_LEN		(512 * 1024)	/* Reserved for malloc */

 /*
  * Local Bus LCRR and LBCR regs
  */
 #define CFG_LCRR	LCRR_EADC_1 | LCRR_CLKDIV_4
 #define CFG_LBC_LBCR	( 0x00040000 /* TODO */ \
 			| (0xFF << LBCR_BMT_SHIFT) \
 			| 0xF )	/* 0x0004ff0f */

 #define CFG_LBC_MRTPR	0x20000000  /*TODO */ 	/* LB refresh timer prescal, 266MHz/32 */

 /* drivers/mtd/nand/nand.c */
 #define CFG_NAND_BASE		0xE2800000	/* 0xF0000000 */
 #define CFG_MAX_NAND_DEVICE	1
 #define NAND_MAX_CHIPS		1
 #define CONFIG_MTD_NAND_VERIFY_WRITE

 #define CFG_BR1_PRELIM		( CFG_NAND_BASE \
 				| (2<<BR_DECC_SHIFT)	/* Use HW ECC */ \
 				| BR_PS_8		/* Port Size = 8 bit */ \
 				| BR_MS_FCM		/* MSEL = FCM */ \
 				| BR_V )		/* valid */
 #define CFG_OR1_PRELIM		( 0xFFFF8000		/* length 32K */ \
 				| OR_FCM_CSCT \
 				| OR_FCM_CST \
 				| OR_FCM_CHT \
 				| OR_FCM_SCY_1 \
 				| OR_FCM_TRLX \
 				| OR_FCM_EHTR )
 				/* 0xFFFF8396 */
 #define CFG_LBLAWBAR1_PRELIM	CFG_NAND_BASE
 #define CFG_LBLAWAR1_PRELIM	0x8000000E	/* 32KB  */

 /* local bus read write buffer mapping */
 #define CFG_BR3_PRELIM		0xFA000801	/* map at 0xFA000000 */
 #define CFG_OR3_PRELIM		0xFFFF8FF7	/* 32kB */
 #define CFG_LBLAWBAR3_PRELIM	0xFA000000
 #define CFG_LBLAWAR3_PRELIM	0x8000000E	/* 32KB  */

 /* Vitesse 7385 */

 #define CFG_VSC7385_BASE	0xF0000000

 #ifdef CONFIG_VSC7385_ENET

 #define CFG_BR2_PRELIM		0xf0000801	/* VSC7385 Base address */
 #define CFG_OR2_PRELIM		0xfffe09ff	/* VSC7385, 128K bytes*/
 #define CFG_LBLAWBAR2_PRELIM	CFG_VSC7385_BASE/* Access window base at VSC7385 base */
 #define CFG_LBLAWAR2_PRELIM	0x80000010	/* Access window size 128K */

 #endif

 /* pass open firmware flat tree */
 #define CONFIG_OF_LIBFDT	1
 #define CONFIG_OF_BOARD_SETUP	1
 #define CONFIG_OF_STDOUT_VIA_ALIAS	1

 /*
  * Serial Port
  */
 #define CONFIG_CONS_INDEX	1
 #define CFG_NS16550
 #define CFG_NS16550_SERIAL
 #define CFG_NS16550_REG_SIZE	1
 #define CFG_NS16550_CLK		get_bus_freq(0)

 #define CFG_BAUDRATE_TABLE	\
 	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}

 #define CFG_NS16550_COM1	(CFG_IMMR+0x4500)
 #define CFG_NS16550_COM2	(CFG_IMMR+0x4600)

 /* Use the HUSH parser */
 #define CFG_HUSH_PARSER
 #define CFG_PROMPT_HUSH_PS2 "> "

 /* I2C */
 #define CONFIG_HARD_I2C			/* I2C with hardware support*/
 #define CONFIG_FSL_I2C
 #define CONFIG_I2C_MULTI_BUS
 #define CONFIG_I2C_CMD_TREE
 #define CFG_I2C_SPEED		400000	/* I2C speed and slave address */
 #define CFG_I2C_SLAVE		0x7F
 #define CFG_I2C_NOPROBES	{{0,0x69}} /* Don't probe these addrs */
 #define CFG_I2C_OFFSET		0x3000
 #define CFG_I2C2_OFFSET		0x3100

 /*
  * General PCI
  * Addresses are mapped 1-1.
  */
 #define CFG_PCI1_MEM_BASE	0x80000000
 #define CFG_PCI1_MEM_PHYS	CFG_PCI1_MEM_BASE
 #define CFG_PCI1_MEM_SIZE	0x10000000	/* 256M */
 #define CFG_PCI1_MMIO_BASE	0x90000000
 #define CFG_PCI1_MMIO_PHYS	CFG_PCI1_MMIO_BASE
 #define CFG_PCI1_MMIO_SIZE	0x10000000	/* 256M */
 #define CFG_PCI1_IO_BASE	0x00000000
 #define CFG_PCI1_IO_PHYS	0xE2000000
 #define CFG_PCI1_IO_SIZE	0x00100000	/* 1M */

 #define CONFIG_PCI_PNP		/* do pci plug-and-play */
 #define CFG_PCI_SUBSYS_VENDORID 0x1057	/* Motorola */

 /*
  * TSEC
  */
 #define CONFIG_TSEC_ENET		/* TSEC ethernet support */

 #define CONFIG_NET_MULTI
 #define CONFIG_GMII			/* MII PHY management */

 #ifdef CONFIG_TSEC1
 #define CONFIG_HAS_ETH0
 #define CONFIG_TSEC1_NAME	"TSEC0"
 #define CFG_TSEC1_OFFSET	0x24000
 #define TSEC1_PHY_ADDR		0x1c
 #define TSEC1_FLAGS		TSEC_GIGABIT
 #define TSEC1_PHYIDX		0
 #endif

 #ifdef CONFIG_TSEC2
 #define CONFIG_HAS_ETH1
 #define CONFIG_TSEC2_NAME	"TSEC1"
 #define CFG_TSEC2_OFFSET	0x25000
 #define TSEC2_PHY_ADDR		4
 #define TSEC2_FLAGS		TSEC_GIGABIT
 #define TSEC2_PHYIDX		0
 #endif


 /* Options are: TSEC[0-1] */
 #define CONFIG_ETHPRIME			"TSEC1"

 /*
  * Configure on-board RTC
  */
 #define CONFIG_RTC_DS1337
 #define CFG_I2C_RTC_ADDR		0x68

 /*
  * Environment
  */
 #ifndef CFG_RAMBOOT
 	#define CFG_ENV_IS_IN_FLASH	1
 	#define CFG_ENV_ADDR		(CFG_MONITOR_BASE + CFG_MONITOR_LEN)
 	#define CFG_ENV_SECT_SIZE	0x10000	/* 64K(one sector) for env */
 	#define CFG_ENV_SIZE		0x2000

 /* Address and size of Redundant Environment Sector */
 #else
 	#define CFG_ENV_IS_NOWHERE	1	/* Store ENV in memory only */
 	#define CFG_ENV_ADDR		(CFG_MONITOR_BASE - 0x1000)
 	#define CFG_ENV_SIZE		0x2000
 #endif

 #define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
 #define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change */

 /*
  * BOOTP options
  */
 #define CONFIG_BOOTP_BOOTFILESIZE
 #define CONFIG_BOOTP_BOOTPATH
 #define CONFIG_BOOTP_GATEWAY
 #define CONFIG_BOOTP_HOSTNAME


 /*
  * Command line configuration.
  */
 #include <config_cmd_default.h>

 #define CONFIG_CMD_PING
 #define CONFIG_CMD_DHCP
 #define CONFIG_CMD_I2C
 #define CONFIG_CMD_MII
 #define CONFIG_CMD_DATE
 #define CONFIG_CMD_PCI

 #if defined(CFG_RAMBOOT)
     #undef CONFIG_CMD_ENV
     #undef CONFIG_CMD_LOADS
 #endif

 #define CONFIG_CMDLINE_EDITING 1


 /*
  * Miscellaneous configurable options
  */
 #define CFG_LONGHELP			/* undef to save memory */
 #define CFG_LOAD_ADDR	0x2000000	/* default load address */
 #define CFG_PROMPT	"=> "		/* Monitor Command Prompt */
 #define CFG_CBSIZE	1024		/* Console I/O Buffer Size */

 #define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16)	/* Print Buffer Size */
 #define CFG_MAXARGS	16		/* max number of command args */
 #define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size */
 #define CFG_HZ		1000		/* decrementer freq: 1ms ticks */

 /*
  * For booting Linux, the board info and command line data
  * have to be in the first 8 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization.
  */
 #define CFG_BOOTMAPSZ	(8 << 20)	/* Initial Memory map for Linux*/

 #define CFG_RCWH_PCIHOST 0x80000000	/* PCIHOST  */

 #ifdef CFG_66MHZ

 /* 66MHz IN, 133MHz CSB, 266 DDR, 266 CORE */
 /* 0x62040000 */
 #define CFG_HRCW_LOW (\
 	0x20000000 /* reserved, must be set */ |\
 	HRCWL_DDRCM |\
 	HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
 	HRCWL_DDR_TO_SCB_CLK_2X1 |\
 	HRCWL_CSB_TO_CLKIN_2X1 |\
 	HRCWL_CORE_TO_CSB_2X1)

 #elif defined(CFG_33MHZ)

 /* 33MHz IN, 165MHz CSB, 330 DDR, 330 CORE */
 /* 0x65040000 */
 #define CFG_HRCW_LOW (\
 	0x20000000 /* reserved, must be set */ |\
 	HRCWL_DDRCM |\
 	HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
 	HRCWL_DDR_TO_SCB_CLK_2X1 |\
 	HRCWL_CSB_TO_CLKIN_5X1 |\
 	HRCWL_CORE_TO_CSB_2X1)

 #endif

 /* 0xa0606c00 */
 #define CFG_HRCW_HIGH (\
 	HRCWH_PCI_HOST |\
 	HRCWH_PCI1_ARBITER_ENABLE |\
 	HRCWH_CORE_ENABLE |\
 	HRCWH_FROM_0X00000100 |\
 	HRCWH_BOOTSEQ_DISABLE |\
 	HRCWH_SW_WATCHDOG_DISABLE |\
 	HRCWH_ROM_LOC_LOCAL_16BIT |\
 	HRCWH_RL_EXT_LEGACY |\
 	HRCWH_TSEC1M_IN_RGMII |\
 	HRCWH_TSEC2M_IN_RGMII |\
 	HRCWH_BIG_ENDIAN |\
 	HRCWH_LALE_NORMAL)

 /* System IO Config */
 #define CFG_SICRH	(SICRH_TSOBI1 | SICRH_TSOBI2)	/* RGMII */
 #define CFG_SICRL	SICRL_USBDR			/* Enable Internal USB Phy  */

 #define CFG_HID0_INIT	0x000000000
 #define CFG_HID0_FINAL	(HID0_ENABLE_MACHINE_CHECK | \
 			 HID0_ENABLE_DYNAMIC_POWER_MANAGMENT)

 #define CFG_HID2 HID2_HBE

 /* DDR @ 0x00000000 */
 #define CFG_IBAT0L	(CFG_SDRAM_BASE | BATL_PP_10)
 #define CFG_IBAT0U	(CFG_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)

 /* PCI @ 0x80000000 */
 #define CFG_IBAT1L	(CFG_PCI1_MEM_BASE | BATL_PP_10)
 #define CFG_IBAT1U	(CFG_PCI1_MEM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
 #define CFG_IBAT2L	(CFG_PCI1_MMIO_BASE | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
 #define CFG_IBAT2U	(CFG_PCI1_MMIO_BASE | BATU_BL_256M | BATU_VS | BATU_VP)

 /* PCI2 not supported on 8313 */
 #define CFG_IBAT3L	(0)
 #define CFG_IBAT3U	(0)
 #define CFG_IBAT4L	(0)
 #define CFG_IBAT4U	(0)

 /* IMMRBAR @ 0xE0000000, PCI IO @ 0xE2000000 & BCSR @ 0xE2400000 */
 #define CFG_IBAT5L	(CFG_IMMR | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
 #define CFG_IBAT5U	(CFG_IMMR | BATU_BL_256M | BATU_VS | BATU_VP)

 /* SDRAM @ 0xF0000000, stack in DCACHE 0xFDF00000 & FLASH @ 0xFE000000 */
 #define CFG_IBAT6L	(0xF0000000 | BATL_PP_10)
 #define CFG_IBAT6U	(0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP)

 #define CFG_IBAT7L	(0)
 #define CFG_IBAT7U	(0)

 #define CFG_DBAT0L	CFG_IBAT0L
 #define CFG_DBAT0U	CFG_IBAT0U
 #define CFG_DBAT1L	CFG_IBAT1L
 #define CFG_DBAT1U	CFG_IBAT1U
 #define CFG_DBAT2L	CFG_IBAT2L
 #define CFG_DBAT2U	CFG_IBAT2U
 #define CFG_DBAT3L	CFG_IBAT3L
 #define CFG_DBAT3U	CFG_IBAT3U
 #define CFG_DBAT4L	CFG_IBAT4L
 #define CFG_DBAT4U	CFG_IBAT4U
 #define CFG_DBAT5L	CFG_IBAT5L
 #define CFG_DBAT5U	CFG_IBAT5U
 #define CFG_DBAT6L	CFG_IBAT6L
 #define CFG_DBAT6U	CFG_IBAT6U
 #define CFG_DBAT7L	CFG_IBAT7L
 #define CFG_DBAT7U	CFG_IBAT7U

 /*
  * Internal Definitions
  *
  * Boot Flags
  */
 #define BOOTFLAG_COLD	0x01	/* Normal Power-On: Boot from FLASH */
 #define BOOTFLAG_WARM	0x02	/* Software reboot */

 /*
  * Environment Configuration
  */
 #define CONFIG_ENV_OVERWRITE

 #define CONFIG_ETHADDR		00:E0:0C:00:95:01
 #define CONFIG_ETH1ADDR		00:E0:0C:00:95:02

 #define CONFIG_IPADDR		10.0.0.2
 #define CONFIG_SERVERIP		10.0.0.1
 #define CONFIG_GATEWAYIP	10.0.0.1
 #define CONFIG_NETMASK		255.0.0.0
 #define CONFIG_NETDEV		eth1

 #define CONFIG_HOSTNAME		mpc8313erdb
 #define CONFIG_ROOTPATH		/nfs/root/path
 #define CONFIG_BOOTFILE		uImage
 #define CONFIG_UBOOTPATH	u-boot.bin	/* U-Boot image on TFTP server */
 #define CONFIG_FDTFILE		mpc8313erdb.dtb

 #define CONFIG_LOADADDR		500000	/* default location for tftp and bootm */
 #define CONFIG_BOOTDELAY	-1	/* -1 disables auto-boot */
 #define CONFIG_BAUDRATE		115200

 #define XMK_STR(x)	#x
 #define MK_STR(x)	XMK_STR(x)

 #define CONFIG_EXTRA_ENV_SETTINGS \
 	"netdev=" MK_STR(CONFIG_NETDEV) "\0" 				\
 	"ethprime=TSEC1\0"						\
 	"uboot=" MK_STR(CONFIG_UBOOTPATH) "\0" 				\
 	"tftpflash=tftpboot $loadaddr $uboot; " 			\
 		"protect off " MK_STR(TEXT_BASE) " +$filesize; " 	\
 		"erase " MK_STR(TEXT_BASE) " +$filesize; " 		\
 		"cp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize; " 	\
 		"protect on " MK_STR(TEXT_BASE) " +$filesize; " 	\
 		"cmp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize\0" 	\
 	"fdtaddr=400000\0"						\
 	"fdtfile=" MK_STR(CONFIG_FDTFILE) "\0"				\
 	"console=ttyS0\0"						\
 	"setbootargs=setenv bootargs "					\
 		"root=$rootdev rw console=$console,$baudrate $othbootargs\0" \
 	"setipargs=setenv bootargs nfsroot=$serverip:$rootpath " \
 		"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
 		"root=$rootdev rw console=$console,$baudrate $othbootargs\0"

 #define CONFIG_NFSBOOTCOMMAND						\
 	"setenv rootdev /dev/nfs;"					\
 	"run setbootargs;"							\
 	"run setipargs;"							\
 	"tftp $loadaddr $bootfile;"					\
 	"tftp $fdtaddr $fdtfile;"					\
 	"bootm $loadaddr - $fdtaddr"

 #define CONFIG_RAMBOOTCOMMAND						\
 	"setenv rootdev /dev/ram;"					\
 	"run setbootargs;"						\
 	"tftp $ramdiskaddr $ramdiskfile;"				\
 	"tftp $loadaddr $bootfile;"					\
 	"tftp $fdtaddr $fdtfile;"					\
 	"bootm $loadaddr $ramdiskaddr $fdtaddr"

 #undef MK_STR
 #undef XMK_STR

 #endif	/* __CONFIG_H */
	/*
	* Copyright (C) Freescale Semiconductor, Inc. 2006.
	*
	* See file CREDITS for list of people who contributed to this
	* project.
	*
	* This program is free software; you can redistribute it and/or
	* modify it under the terms of the GNU General Public License as
	* published by the Free Software Foundation; either version 2 of
	* the License, or (at your option) any later version.
	*
	* This program is distributed in the hope that it will be useful,
	* but WITHOUT ANY WARRANTY; without even the implied warranty of
	* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
	* GNU General Public License for more details.
	*
	* You should have received a copy of the GNU General Public License
	* along with this program; if not, write to the Free Software
	* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
	* MA 02111-1307 USA
	*/
	/*
	* mpc8313epb board configuration file
	*/

	#ifndef __CONFIG_H
	#define __CONFIG_H

	/*
	* High Level Configuration Options
	*/
	#define CONFIG_E300 1
	#define CONFIG_MPC83XX 1
	#define CONFIG_MPC831X 1
	#define CONFIG_MPC8313 1
	#define CONFIG_MPC8313ERDB 1

	#define CONFIG_PCI
	#define CONFIG_83XX_GENERIC_PCI

	#define CONFIG_MISC_INIT_R

	/*
	* On-board devices
	*
	* TSEC1 is VSC switch
	* TSEC2 is SoC TSEC
	*/
	#define CONFIG_VSC7385_ENET
	#define CONFIG_TSEC2

	#ifdef CFG_66MHZ
	#define CONFIG_83XX_CLKIN 66666667 /* in Hz */
	#elif defined(CFG_33MHZ)
	#define CONFIG_83XX_CLKIN 33333333 /* in Hz */
	#else
	#error Unknown oscillator frequency.
	#endif

	#define CONFIG_SYS_CLK_FREQ CONFIG_83XX_CLKIN

	#define CONFIG_BOARD_EARLY_INIT_F /* call board_pre_init */

	#define CFG_IMMR 0xE0000000

	#define CFG_MEMTEST_START 0x00001000
	#define CFG_MEMTEST_END 0x07f00000

	/* Early revs of this board will lock up hard when attempting
	* to access the PMC registers, unless a JTAG debugger is
	* connected, or some resistor modifications are made.
	*/
	#define CFG_8313ERDB_BROKEN_PMC 1

	#define CFG_ACR_PIPE_DEP 3 /* Arbiter pipeline depth (0-3) */
	#define CFG_ACR_RPTCNT 3 /* Arbiter repeat count (0-7) */

	/*
	* Device configurations
	*/

	/* Vitesse 7385 */

	#ifdef CONFIG_VSC7385_ENET

	#define CONFIG_TSEC1

	/* The flash address and size of the VSC7385 firmware image */
	#define CONFIG_VSC7385_IMAGE 0xFE7FE000
	#define CONFIG_VSC7385_IMAGE_SIZE 8192

	#endif

	/*
	* DDR Setup
	*/
	#define CFG_DDR_BASE 0x00000000 /* DDR is system memory*/
	#define CFG_SDRAM_BASE CFG_DDR_BASE
	#define CFG_DDR_SDRAM_BASE CFG_DDR_BASE

	/*
	* Manually set up DDR parameters, as this board does not
	* seem to have the SPD connected to I2C.
	*/
	#define CFG_DDR_SIZE 128 /* MB */
	#define CFG_DDR_CONFIG ( CSCONFIG_EN \
	\| 0x00010000 /* TODO */ \
	\| CSCONFIG_ROW_BIT_13 \| CSCONFIG_COL_BIT_10 )
	/* 0x80010102 */

	#define CFG_DDR_TIMING_3 0x00000000
	#define CFG_DDR_TIMING_0 ( ( 0 << TIMING_CFG0_RWT_SHIFT ) \
	\| ( 0 << TIMING_CFG0_WRT_SHIFT ) \
	\| ( 0 << TIMING_CFG0_RRT_SHIFT ) \
	\| ( 0 << TIMING_CFG0_WWT_SHIFT ) \
	\| ( 2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT ) \
	\| ( 2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT ) \
	\| ( 8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT ) \
	\| ( 2 << TIMING_CFG0_MRS_CYC_SHIFT ) )
	/* 0x00220802 */
	#define CFG_DDR_TIMING_1 ( ( 3 << TIMING_CFG1_PRETOACT_SHIFT ) \
	\| ( 8 << TIMING_CFG1_ACTTOPRE_SHIFT ) \
	\| ( 3 << TIMING_CFG1_ACTTORW_SHIFT ) \
	\| ( 5 << TIMING_CFG1_CASLAT_SHIFT ) \
	\| (10 << TIMING_CFG1_REFREC_SHIFT ) \
	\| ( 3 << TIMING_CFG1_WRREC_SHIFT ) \
	\| ( 2 << TIMING_CFG1_ACTTOACT_SHIFT ) \
	\| ( 2 << TIMING_CFG1_WRTORD_SHIFT ) )
	/* 0x3835a322 */
	#define CFG_DDR_TIMING_2 ( ( 1 << TIMING_CFG2_ADD_LAT_SHIFT ) \
	\| ( 5 << TIMING_CFG2_CPO_SHIFT ) \
	\| ( 2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT ) \
	\| ( 2 << TIMING_CFG2_RD_TO_PRE_SHIFT ) \
	\| ( 2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT ) \
	\| ( 3 << TIMING_CFG2_CKE_PLS_SHIFT ) \
	\| ( 6 << TIMING_CFG2_FOUR_ACT_SHIFT) )
	/* 0x129048c6 / / P9-45,may need tuning */
	#define CFG_DDR_INTERVAL ( ( 1296 << SDRAM_INTERVAL_REFINT_SHIFT ) \
	\| ( 1280 << SDRAM_INTERVAL_BSTOPRE_SHIFT ) )
	/* 0x05100500 */
	#if defined(CONFIG_DDR_2T_TIMING)
	#define CFG_SDRAM_CFG ( SDRAM_CFG_SREN \
	\| SDRAM_CFG_SDRAM_TYPE_DDR2 \
	\| SDRAM_CFG_2T_EN \
	\| SDRAM_CFG_DBW_32 )
	#else
	#define CFG_SDRAM_CFG ( SDRAM_CFG_SREN \
	\| SDRAM_CFG_SDRAM_TYPE_DDR2 \
	\| SDRAM_CFG_32_BE )
	/* 0x43080000 */
	#endif
	#define CFG_SDRAM_CFG2 0x00401000;
	/* set burst length to 8 for 32-bit data path */
	#define CFG_DDR_MODE ( ( 0x4448 << SDRAM_MODE_ESD_SHIFT ) \
	\| ( 0x0632 << SDRAM_MODE_SD_SHIFT ) )
	/* 0x44480632 */
	#define CFG_DDR_MODE_2 0x8000C000;

	#define CFG_DDR_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
	/0x02000000/
	#define CFG_DDRCDR_VALUE ( DDRCDR_EN \
	\| DDRCDR_PZ_NOMZ \
	\| DDRCDR_NZ_NOMZ \
	\| DDRCDR_M_ODR )

	/*
	* FLASH on the Local Bus
	*/
	#define CFG_FLASH_CFI /* use the Common Flash Interface */
	#define CFG_FLASH_CFI_DRIVER /* use the CFI driver */
	#define CFG_FLASH_BASE 0xFE000000 /* start of FLASH */
	#define CFG_FLASH_SIZE 8 /* flash size in MB */
	#define CFG_FLASH_EMPTY_INFO /* display empty sectors */
	#define CFG_FLASH_USE_BUFFER_WRITE /* buffer up multiple bytes */

	#define CFG_BR0_PRELIM (CFG_FLASH_BASE \| /* flash Base address */ \
	(2 << BR_PS_SHIFT) \| /* 16 bit port size */ \
	BR_V) /* valid */
	#define CFG_OR0_PRELIM ( 0xFF000000 /* 16 MByte */ \
	\| OR_GPCM_XACS \
	\| OR_GPCM_SCY_9 \
	\| OR_GPCM_EHTR \
	\| OR_GPCM_EAD )
	/* 0xFF006FF7 TODO SLOW 16 MB flash size */
	#define CFG_LBLAWBAR0_PRELIM CFG_FLASH_BASE /* window base at flash base */
	#define CFG_LBLAWAR0_PRELIM 0x80000017 /* 16 MB window size */

	#define CFG_MAX_FLASH_BANKS 1 /* number of banks */
	#define CFG_MAX_FLASH_SECT 135 /* sectors per device */

	#define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
	#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */

	#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */

	#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
	#define CFG_RAMBOOT
	#endif

	#define CFG_INIT_RAM_LOCK 1
	#define CFG_INIT_RAM_ADDR 0xFD000000 /* Initial RAM address */
	#define CFG_INIT_RAM_END 0x1000 /* End of used area in RAM*/

	#define CFG_GBL_DATA_SIZE 0x100 /* num bytes initial data */
	#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
	#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET

	/* CFG_MONITOR_LEN must be a multiple of CFG_ENV_SECT_SIZE */
	#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
	#define CFG_MALLOC_LEN (512 * 1024) /* Reserved for malloc */

	/*
	* Local Bus LCRR and LBCR regs
	*/
	#define CFG_LCRR LCRR_EADC_1 \| LCRR_CLKDIV_4
	#define CFG_LBC_LBCR ( 0x00040000 /* TODO */ \
	\| (0xFF << LBCR_BMT_SHIFT) \
	\| 0xF ) /* 0x0004ff0f */

	#define CFG_LBC_MRTPR 0x20000000 /TODO / /* LB refresh timer prescal, 266MHz/32 */

	/* drivers/mtd/nand/nand.c */
	#define CFG_NAND_BASE 0xE2800000 /* 0xF0000000 */
	#define CFG_MAX_NAND_DEVICE 1
	#define NAND_MAX_CHIPS 1
	#define CONFIG_MTD_NAND_VERIFY_WRITE

	#define CFG_BR1_PRELIM ( CFG_NAND_BASE \
	\| (2<<BR_DECC_SHIFT) /* Use HW ECC */ \
	\| BR_PS_8 /* Port Size = 8 bit */ \
	\| BR_MS_FCM /* MSEL = FCM */ \
	\| BR_V ) /* valid */
	#define CFG_OR1_PRELIM ( 0xFFFF8000 /* length 32K */ \
	\| OR_FCM_CSCT \
	\| OR_FCM_CST \
	\| OR_FCM_CHT \
	\| OR_FCM_SCY_1 \
	\| OR_FCM_TRLX \
	\| OR_FCM_EHTR )
	/* 0xFFFF8396 */
	#define CFG_LBLAWBAR1_PRELIM CFG_NAND_BASE
	#define CFG_LBLAWAR1_PRELIM 0x8000000E /* 32KB */

	/* local bus read write buffer mapping */
	#define CFG_BR3_PRELIM 0xFA000801 /* map at 0xFA000000 */
	#define CFG_OR3_PRELIM 0xFFFF8FF7 /* 32kB */
	#define CFG_LBLAWBAR3_PRELIM 0xFA000000
	#define CFG_LBLAWAR3_PRELIM 0x8000000E /* 32KB */

	/* Vitesse 7385 */

	#define CFG_VSC7385_BASE 0xF0000000

	#ifdef CONFIG_VSC7385_ENET

	#define CFG_BR2_PRELIM 0xf0000801 /* VSC7385 Base address */
	#define CFG_OR2_PRELIM 0xfffe09ff /* VSC7385, 128K bytes*/
	#define CFG_LBLAWBAR2_PRELIM CFG_VSC7385_BASE/* Access window base at VSC7385 base */
	#define CFG_LBLAWAR2_PRELIM 0x80000010 /* Access window size 128K */

	#endif

	/* pass open firmware flat tree */
	#define CONFIG_OF_LIBFDT 1
	#define CONFIG_OF_BOARD_SETUP 1
	#define CONFIG_OF_STDOUT_VIA_ALIAS 1

	/*
	* Serial Port
	*/
	#define CONFIG_CONS_INDEX 1
	#define CFG_NS16550
	#define CFG_NS16550_SERIAL
	#define CFG_NS16550_REG_SIZE 1
	#define CFG_NS16550_CLK get_bus_freq(0)

	#define CFG_BAUDRATE_TABLE \
	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}

	#define CFG_NS16550_COM1 (CFG_IMMR+0x4500)
	#define CFG_NS16550_COM2 (CFG_IMMR+0x4600)

	/* Use the HUSH parser */
	#define CFG_HUSH_PARSER
	#define CFG_PROMPT_HUSH_PS2 "> "

	/* I2C */
	#define CONFIG_HARD_I2C /* I2C with hardware support*/
	#define CONFIG_FSL_I2C
	#define CONFIG_I2C_MULTI_BUS
	#define CONFIG_I2C_CMD_TREE
	#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
	#define CFG_I2C_SLAVE 0x7F
	#define CFG_I2C_NOPROBES {{0,0x69}} /* Don't probe these addrs */
	#define CFG_I2C_OFFSET 0x3000
	#define CFG_I2C2_OFFSET 0x3100

	/*
	* General PCI
	* Addresses are mapped 1-1.
	*/
	#define CFG_PCI1_MEM_BASE 0x80000000
	#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE
	#define CFG_PCI1_MEM_SIZE 0x10000000 /* 256M */
	#define CFG_PCI1_MMIO_BASE 0x90000000
	#define CFG_PCI1_MMIO_PHYS CFG_PCI1_MMIO_BASE
	#define CFG_PCI1_MMIO_SIZE 0x10000000 /* 256M */
	#define CFG_PCI1_IO_BASE 0x00000000
	#define CFG_PCI1_IO_PHYS 0xE2000000
	#define CFG_PCI1_IO_SIZE 0x00100000 /* 1M */

	#define CONFIG_PCI_PNP /* do pci plug-and-play */
	#define CFG_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */

	/*
	* TSEC
	*/
	#define CONFIG_TSEC_ENET /* TSEC ethernet support */

	#define CONFIG_NET_MULTI
	#define CONFIG_GMII /* MII PHY management */

	#ifdef CONFIG_TSEC1
	#define CONFIG_HAS_ETH0
	#define CONFIG_TSEC1_NAME "TSEC0"
	#define CFG_TSEC1_OFFSET 0x24000
	#define TSEC1_PHY_ADDR 0x1c
	#define TSEC1_FLAGS TSEC_GIGABIT
	#define TSEC1_PHYIDX 0
	#endif

	#ifdef CONFIG_TSEC2
	#define CONFIG_HAS_ETH1
	#define CONFIG_TSEC2_NAME "TSEC1"
	#define CFG_TSEC2_OFFSET 0x25000
	#define TSEC2_PHY_ADDR 4
	#define TSEC2_FLAGS TSEC_GIGABIT
	#define TSEC2_PHYIDX 0
	#endif


	/* Options are: TSEC[0-1] */
	#define CONFIG_ETHPRIME "TSEC1"

	/*
	* Configure on-board RTC
	*/
	#define CONFIG_RTC_DS1337
	#define CFG_I2C_RTC_ADDR 0x68

	/*
	* Environment
	*/
	#ifndef CFG_RAMBOOT
	#define CFG_ENV_IS_IN_FLASH 1
	#define CFG_ENV_ADDR (CFG_MONITOR_BASE + CFG_MONITOR_LEN)
	#define CFG_ENV_SECT_SIZE 0x10000 /* 64K(one sector) for env */
	#define CFG_ENV_SIZE 0x2000

	/* Address and size of Redundant Environment Sector */
	#else
	#define CFG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
	#define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000)
	#define CFG_ENV_SIZE 0x2000
	#endif

	#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
	#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */

	/*
	* BOOTP options
	*/
	#define CONFIG_BOOTP_BOOTFILESIZE
	#define CONFIG_BOOTP_BOOTPATH
	#define CONFIG_BOOTP_GATEWAY
	#define CONFIG_BOOTP_HOSTNAME


	/*
	* Command line configuration.
	*/
	#include <config_cmd_default.h>

	#define CONFIG_CMD_PING
	#define CONFIG_CMD_DHCP
	#define CONFIG_CMD_I2C
	#define CONFIG_CMD_MII
	#define CONFIG_CMD_DATE
	#define CONFIG_CMD_PCI

	#if defined(CFG_RAMBOOT)
	#undef CONFIG_CMD_ENV
	#undef CONFIG_CMD_LOADS
	#endif

	#define CONFIG_CMDLINE_EDITING 1


	/*
	* Miscellaneous configurable options
	*/
	#define CFG_LONGHELP /* undef to save memory */
	#define CFG_LOAD_ADDR 0x2000000 /* default load address */
	#define CFG_PROMPT "=> " /* Monitor Command Prompt */
	#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */

	#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
	#define CFG_MAXARGS 16 /* max number of command args */
	#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
	#define CFG_HZ 1000 /* decrementer freq: 1ms ticks */

	/*
	* For booting Linux, the board info and command line data
	* have to be in the first 8 MB of memory, since this is
	* the maximum mapped by the Linux kernel during initialization.
	*/
	#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/

	#define CFG_RCWH_PCIHOST 0x80000000 /* PCIHOST */

	#ifdef CFG_66MHZ

	/* 66MHz IN, 133MHz CSB, 266 DDR, 266 CORE */
	/* 0x62040000 */
	#define CFG_HRCW_LOW (\
	0x20000000 /* reserved, must be set */ \|\
	HRCWL_DDRCM \|\
	HRCWL_LCL_BUS_TO_SCB_CLK_1X1 \|\
	HRCWL_DDR_TO_SCB_CLK_2X1 \|\
	HRCWL_CSB_TO_CLKIN_2X1 \|\
	HRCWL_CORE_TO_CSB_2X1)

	#elif defined(CFG_33MHZ)

	/* 33MHz IN, 165MHz CSB, 330 DDR, 330 CORE */
	/* 0x65040000 */
	#define CFG_HRCW_LOW (\
	0x20000000 /* reserved, must be set */ \|\
	HRCWL_DDRCM \|\
	HRCWL_LCL_BUS_TO_SCB_CLK_1X1 \|\
	HRCWL_DDR_TO_SCB_CLK_2X1 \|\
	HRCWL_CSB_TO_CLKIN_5X1 \|\
	HRCWL_CORE_TO_CSB_2X1)

	#endif

	/* 0xa0606c00 */
	#define CFG_HRCW_HIGH (\
	HRCWH_PCI_HOST \|\
	HRCWH_PCI1_ARBITER_ENABLE \|\
	HRCWH_CORE_ENABLE \|\
	HRCWH_FROM_0X00000100 \|\
	HRCWH_BOOTSEQ_DISABLE \|\
	HRCWH_SW_WATCHDOG_DISABLE \|\
	HRCWH_ROM_LOC_LOCAL_16BIT \|\
	HRCWH_RL_EXT_LEGACY \|\
	HRCWH_TSEC1M_IN_RGMII \|\
	HRCWH_TSEC2M_IN_RGMII \|\
	HRCWH_BIG_ENDIAN \|\
	HRCWH_LALE_NORMAL)

	/* System IO Config */
	#define CFG_SICRH (SICRH_TSOBI1 \| SICRH_TSOBI2) /* RGMII */
	#define CFG_SICRL SICRL_USBDR /* Enable Internal USB Phy */

	#define CFG_HID0_INIT 0x000000000
	#define CFG_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK \| \
	HID0_ENABLE_DYNAMIC_POWER_MANAGMENT)

	#define CFG_HID2 HID2_HBE

	/* DDR @ 0x00000000 */
	#define CFG_IBAT0L (CFG_SDRAM_BASE \| BATL_PP_10)
	#define CFG_IBAT0U (CFG_SDRAM_BASE \| BATU_BL_256M \| BATU_VS \| BATU_VP)

	/* PCI @ 0x80000000 */
	#define CFG_IBAT1L (CFG_PCI1_MEM_BASE \| BATL_PP_10)
	#define CFG_IBAT1U (CFG_PCI1_MEM_BASE \| BATU_BL_256M \| BATU_VS \| BATU_VP)
	#define CFG_IBAT2L (CFG_PCI1_MMIO_BASE \| BATL_PP_10 \| BATL_CACHEINHIBIT \| BATL_GUARDEDSTORAGE)
	#define CFG_IBAT2U (CFG_PCI1_MMIO_BASE \| BATU_BL_256M \| BATU_VS \| BATU_VP)

	/* PCI2 not supported on 8313 */
	#define CFG_IBAT3L (0)
	#define CFG_IBAT3U (0)
	#define CFG_IBAT4L (0)
	#define CFG_IBAT4U (0)

	/* IMMRBAR @ 0xE0000000, PCI IO @ 0xE2000000 & BCSR @ 0xE2400000 */
	#define CFG_IBAT5L (CFG_IMMR \| BATL_PP_10 \| BATL_CACHEINHIBIT \| BATL_GUARDEDSTORAGE)
	#define CFG_IBAT5U (CFG_IMMR \| BATU_BL_256M \| BATU_VS \| BATU_VP)

	/* SDRAM @ 0xF0000000, stack in DCACHE 0xFDF00000 & FLASH @ 0xFE000000 */
	#define CFG_IBAT6L (0xF0000000 \| BATL_PP_10)
	#define CFG_IBAT6U (0xF0000000 \| BATU_BL_256M \| BATU_VS \| BATU_VP)

	#define CFG_IBAT7L (0)
	#define CFG_IBAT7U (0)

	#define CFG_DBAT0L CFG_IBAT0L
	#define CFG_DBAT0U CFG_IBAT0U
	#define CFG_DBAT1L CFG_IBAT1L
	#define CFG_DBAT1U CFG_IBAT1U
	#define CFG_DBAT2L CFG_IBAT2L
	#define CFG_DBAT2U CFG_IBAT2U
	#define CFG_DBAT3L CFG_IBAT3L
	#define CFG_DBAT3U CFG_IBAT3U
	#define CFG_DBAT4L CFG_IBAT4L
	#define CFG_DBAT4U CFG_IBAT4U
	#define CFG_DBAT5L CFG_IBAT5L
	#define CFG_DBAT5U CFG_IBAT5U
	#define CFG_DBAT6L CFG_IBAT6L
	#define CFG_DBAT6U CFG_IBAT6U
	#define CFG_DBAT7L CFG_IBAT7L
	#define CFG_DBAT7U CFG_IBAT7U

	/*
	* Internal Definitions
	*
	* Boot Flags
	*/
	#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
	#define BOOTFLAG_WARM 0x02 /* Software reboot */

	/*
	* Environment Configuration
	*/
	#define CONFIG_ENV_OVERWRITE

	#define CONFIG_ETHADDR 00:E0:0C:00:95:01
	#define CONFIG_ETH1ADDR 00:E0:0C:00:95:02

	#define CONFIG_IPADDR 10.0.0.2
	#define CONFIG_SERVERIP 10.0.0.1
	#define CONFIG_GATEWAYIP 10.0.0.1
	#define CONFIG_NETMASK 255.0.0.0
	#define CONFIG_NETDEV eth1

	#define CONFIG_HOSTNAME mpc8313erdb
	#define CONFIG_ROOTPATH /nfs/root/path
	#define CONFIG_BOOTFILE uImage
	#define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */
	#define CONFIG_FDTFILE mpc8313erdb.dtb

	#define CONFIG_LOADADDR 500000 /* default location for tftp and bootm */
	#define CONFIG_BOOTDELAY -1 /* -1 disables auto-boot */
	#define CONFIG_BAUDRATE 115200

	#define XMK_STR(x) #x
	#define MK_STR(x) XMK_STR(x)

	#define CONFIG_EXTRA_ENV_SETTINGS \
	"netdev=" MK_STR(CONFIG_NETDEV) "\0" \
	"ethprime=TSEC1\0" \
	"uboot=" MK_STR(CONFIG_UBOOTPATH) "\0" \
	"tftpflash=tftpboot $loadaddr $uboot; " \
	"protect off " MK_STR(TEXT_BASE) " +$filesize; " \
	"erase " MK_STR(TEXT_BASE) " +$filesize; " \
	"cp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize; " \
	"protect on " MK_STR(TEXT_BASE) " +$filesize; " \
	"cmp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize\0" \
	"fdtaddr=400000\0" \
	"fdtfile=" MK_STR(CONFIG_FDTFILE) "\0" \
	"console=ttyS0\0" \
	"setbootargs=setenv bootargs " \
	"root=$rootdev rw console=$console,$baudrate $othbootargs\0" \
	"setipargs=setenv bootargs nfsroot=$serverip:$rootpath " \
	"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
	"root=$rootdev rw console=$console,$baudrate $othbootargs\0"

	#define CONFIG_NFSBOOTCOMMAND \
	"setenv rootdev /dev/nfs;" \
	"run setbootargs;" \
	"run setipargs;" \
	"tftp $loadaddr $bootfile;" \
	"tftp $fdtaddr $fdtfile;" \
	"bootm $loadaddr - $fdtaddr"

	#define CONFIG_RAMBOOTCOMMAND \
	"setenv rootdev /dev/ram;" \
	"run setbootargs;" \
	"tftp $ramdiskaddr $ramdiskfile;" \
	"tftp $loadaddr $bootfile;" \
	"tftp $fdtaddr $fdtfile;" \
	"bootm $loadaddr $ramdiskaddr $fdtaddr"

	#undef MK_STR
	#undef XMK_STR

	#endif /* __CONFIG_H */