| /* |
| * Copyright 2014 Freescale Semiconductor, Inc. |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| #define CONFIG_LS102XA |
| |
| #define CONFIG_ARMV7_PSCI |
| |
| #define CONFIG_FSL_CLK |
| |
| #define CONFIG_DISPLAY_CPUINFO |
| #define CONFIG_DISPLAY_BOARDINFO |
| |
| #define CONFIG_SKIP_LOWLEVEL_INIT |
| #define CONFIG_BOARD_EARLY_INIT_F |
| #define CONFIG_DEEP_SLEEP |
| #ifdef CONFIG_DEEP_SLEEP |
| #define CONFIG_SILENT_CONSOLE |
| #endif |
| |
| /* |
| * Size of malloc() pool |
| */ |
| #define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 16 * 1024 * 1024) |
| |
| #define CONFIG_SYS_INIT_RAM_ADDR OCRAM_BASE_ADDR |
| #define CONFIG_SYS_INIT_RAM_SIZE OCRAM_SIZE |
| |
| /* |
| * USB |
| */ |
| |
| /* |
| * EHCI Support - disbaled by default as |
| * there is no signal coming out of soc on |
| * this board for this controller. However, |
| * the silicon still has this controller, |
| * and anyone can use this controller by |
| * taking signals out on their board. |
| */ |
| |
| /*#define CONFIG_HAS_FSL_DR_USB*/ |
| |
| #ifdef CONFIG_HAS_FSL_DR_USB |
| #define CONFIG_USB_EHCI |
| #define CONFIG_USB_EHCI_FSL |
| #define CONFIG_EHCI_HCD_INIT_AFTER_RESET |
| #endif |
| |
| /* XHCI Support - enabled by default */ |
| #define CONFIG_HAS_FSL_XHCI_USB |
| |
| #ifdef CONFIG_HAS_FSL_XHCI_USB |
| #define CONFIG_USB_XHCI_FSL |
| #define CONFIG_USB_XHCI_DWC3 |
| #define CONFIG_USB_XHCI |
| #define CONFIG_USB_MAX_CONTROLLER_COUNT 1 |
| #define CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS 2 |
| #endif |
| |
| #if defined(CONFIG_HAS_FSL_DR_USB) || defined(CONFIG_HAS_FSL_XHCI_USB) |
| #define CONFIG_CMD_USB |
| #define CONFIG_USB_STORAGE |
| #define CONFIG_CMD_EXT2 |
| #endif |
| |
| /* |
| * Generic Timer Definitions |
| */ |
| #define GENERIC_TIMER_CLK 12500000 |
| |
| #define CONFIG_SYS_CLK_FREQ 100000000 |
| #define CONFIG_DDR_CLK_FREQ 100000000 |
| |
| #define DDR_SDRAM_CFG 0x470c0008 |
| #define DDR_CS0_BNDS 0x008000bf |
| #define DDR_CS0_CONFIG 0x80014302 |
| #define DDR_TIMING_CFG_0 0x50550004 |
| #define DDR_TIMING_CFG_1 0xbcb38c56 |
| #define DDR_TIMING_CFG_2 0x0040d120 |
| #define DDR_TIMING_CFG_3 0x010e1000 |
| #define DDR_TIMING_CFG_4 0x00000001 |
| #define DDR_TIMING_CFG_5 0x03401400 |
| #define DDR_SDRAM_CFG_2 0x00401010 |
| #define DDR_SDRAM_MODE 0x00061c60 |
| #define DDR_SDRAM_MODE_2 0x00180000 |
| #define DDR_SDRAM_INTERVAL 0x18600618 |
| #define DDR_DDR_WRLVL_CNTL 0x8655f605 |
| #define DDR_DDR_WRLVL_CNTL_2 0x05060607 |
| #define DDR_DDR_WRLVL_CNTL_3 0x05050505 |
| #define DDR_DDR_CDR1 0x80040000 |
| #define DDR_DDR_CDR2 0x00000001 |
| #define DDR_SDRAM_CLK_CNTL 0x02000000 |
| #define DDR_DDR_ZQ_CNTL 0x89080600 |
| #define DDR_CS0_CONFIG_2 0 |
| #define DDR_SDRAM_CFG_MEM_EN 0x80000000 |
| #define SDRAM_CFG2_D_INIT 0x00000010 |
| #define DDR_CDR2_VREF_TRAIN_EN 0x00000080 |
| #define SDRAM_CFG2_FRC_SR 0x80000000 |
| #define SDRAM_CFG_BI 0x00000001 |
| |
| #ifdef CONFIG_RAMBOOT_PBL |
| #define CONFIG_SYS_FSL_PBL_PBI board/freescale/ls1021atwr/ls102xa_pbi.cfg |
| #endif |
| |
| #ifdef CONFIG_SD_BOOT |
| #ifdef CONFIG_SD_BOOT_QSPI |
| #define CONFIG_SYS_FSL_PBL_RCW \ |
| board/freescale/ls1021atwr/ls102xa_rcw_sd_qspi.cfg |
| #else |
| #define CONFIG_SYS_FSL_PBL_RCW \ |
| board/freescale/ls1021atwr/ls102xa_rcw_sd_ifc.cfg |
| #endif |
| #define CONFIG_SPL_FRAMEWORK |
| #define CONFIG_SPL_LDSCRIPT "arch/$(ARCH)/cpu/u-boot-spl.lds" |
| #define CONFIG_SPL_LIBCOMMON_SUPPORT |
| #define CONFIG_SPL_LIBGENERIC_SUPPORT |
| #define CONFIG_SPL_ENV_SUPPORT |
| #define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT |
| #define CONFIG_SPL_I2C_SUPPORT |
| #define CONFIG_SPL_WATCHDOG_SUPPORT |
| #define CONFIG_SPL_SERIAL_SUPPORT |
| #define CONFIG_SPL_MMC_SUPPORT |
| #define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0xe8 |
| #define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x400 |
| |
| #define CONFIG_SPL_TEXT_BASE 0x10000000 |
| #define CONFIG_SPL_MAX_SIZE 0x1a000 |
| #define CONFIG_SPL_STACK 0x1001d000 |
| #define CONFIG_SPL_PAD_TO 0x1c000 |
| #define CONFIG_SYS_TEXT_BASE 0x82000000 |
| |
| #define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SYS_TEXT_BASE + \ |
| CONFIG_SYS_MONITOR_LEN) |
| #define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000 |
| #define CONFIG_SPL_BSS_START_ADDR 0x80100000 |
| #define CONFIG_SPL_BSS_MAX_SIZE 0x80000 |
| #define CONFIG_SYS_MONITOR_LEN 0x80000 |
| #endif |
| |
| #ifdef CONFIG_QSPI_BOOT |
| #define CONFIG_SYS_TEXT_BASE 0x40010000 |
| #endif |
| |
| #if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI) |
| #define CONFIG_SYS_NO_FLASH |
| #endif |
| |
| #ifndef CONFIG_SYS_TEXT_BASE |
| #define CONFIG_SYS_TEXT_BASE 0x60100000 |
| #endif |
| |
| #define CONFIG_NR_DRAM_BANKS 1 |
| #define PHYS_SDRAM 0x80000000 |
| #define PHYS_SDRAM_SIZE (1u * 1024 * 1024 * 1024) |
| |
| #define CONFIG_SYS_DDR_SDRAM_BASE 0x80000000UL |
| #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE |
| |
| #define CONFIG_SYS_HAS_SERDES |
| |
| #define CONFIG_FSL_CAAM /* Enable CAAM */ |
| |
| #if !defined(CONFIG_SD_BOOT) && !defined(CONFIG_NAND_BOOT) && \ |
| !defined(CONFIG_QSPI_BOOT) |
| #define CONFIG_U_QE |
| #endif |
| |
| /* |
| * IFC Definitions |
| */ |
| #if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI) |
| #define CONFIG_FSL_IFC |
| #define CONFIG_SYS_FLASH_BASE 0x60000000 |
| #define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE |
| |
| #define CONFIG_SYS_NOR0_CSPR_EXT (0x0) |
| #define CONFIG_SYS_NOR0_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \ |
| CSPR_PORT_SIZE_16 | \ |
| CSPR_MSEL_NOR | \ |
| CSPR_V) |
| #define CONFIG_SYS_NOR_AMASK IFC_AMASK(128 * 1024 * 1024) |
| |
| /* NOR Flash Timing Params */ |
| #define CONFIG_SYS_NOR_CSOR (CSOR_NOR_ADM_SHIFT(4) | \ |
| CSOR_NOR_TRHZ_80) |
| #define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) | \ |
| FTIM0_NOR_TEADC(0x5) | \ |
| FTIM0_NOR_TAVDS(0x0) | \ |
| FTIM0_NOR_TEAHC(0x5)) |
| #define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \ |
| FTIM1_NOR_TRAD_NOR(0x1A) | \ |
| FTIM1_NOR_TSEQRAD_NOR(0x13)) |
| #define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) | \ |
| FTIM2_NOR_TCH(0x4) | \ |
| FTIM2_NOR_TWP(0x1c) | \ |
| FTIM2_NOR_TWPH(0x0e)) |
| #define CONFIG_SYS_NOR_FTIM3 0 |
| |
| #define CONFIG_FLASH_CFI_DRIVER |
| #define CONFIG_SYS_FLASH_CFI |
| #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE |
| #define CONFIG_SYS_FLASH_QUIET_TEST |
| #define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ |
| |
| #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ |
| #define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ |
| #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ |
| #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ |
| |
| #define CONFIG_SYS_FLASH_EMPTY_INFO |
| #define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE_PHYS } |
| |
| #define CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS |
| #define CONFIG_SYS_WRITE_SWAPPED_DATA |
| #endif |
| |
| /* CPLD */ |
| |
| #define CONFIG_SYS_CPLD_BASE 0x7fb00000 |
| #define CPLD_BASE_PHYS CONFIG_SYS_CPLD_BASE |
| |
| #define CONFIG_SYS_FPGA_CSPR_EXT (0x0) |
| #define CONFIG_SYS_FPGA_CSPR (CSPR_PHYS_ADDR(CPLD_BASE_PHYS) | \ |
| CSPR_PORT_SIZE_8 | \ |
| CSPR_MSEL_GPCM | \ |
| CSPR_V) |
| #define CONFIG_SYS_FPGA_AMASK IFC_AMASK(64 * 1024) |
| #define CONFIG_SYS_FPGA_CSOR (CSOR_NOR_ADM_SHIFT(4) | \ |
| CSOR_NOR_NOR_MODE_AVD_NOR | \ |
| CSOR_NOR_TRHZ_80) |
| |
| /* CPLD Timing parameters for IFC GPCM */ |
| #define CONFIG_SYS_FPGA_FTIM0 (FTIM0_GPCM_TACSE(0xf) | \ |
| FTIM0_GPCM_TEADC(0xf) | \ |
| FTIM0_GPCM_TEAHC(0xf)) |
| #define CONFIG_SYS_FPGA_FTIM1 (FTIM1_GPCM_TACO(0xff) | \ |
| FTIM1_GPCM_TRAD(0x3f)) |
| #define CONFIG_SYS_FPGA_FTIM2 (FTIM2_GPCM_TCS(0xf) | \ |
| FTIM2_GPCM_TCH(0xf) | \ |
| FTIM2_GPCM_TWP(0xff)) |
| #define CONFIG_SYS_FPGA_FTIM3 0x0 |
| #define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT |
| #define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR |
| #define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK |
| #define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR |
| #define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0 |
| #define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1 |
| #define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2 |
| #define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3 |
| #define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_FPGA_CSPR_EXT |
| #define CONFIG_SYS_CSPR1 CONFIG_SYS_FPGA_CSPR |
| #define CONFIG_SYS_AMASK1 CONFIG_SYS_FPGA_AMASK |
| #define CONFIG_SYS_CSOR1 CONFIG_SYS_FPGA_CSOR |
| #define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_FPGA_FTIM0 |
| #define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_FPGA_FTIM1 |
| #define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_FPGA_FTIM2 |
| #define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_FPGA_FTIM3 |
| |
| /* |
| * Serial Port |
| */ |
| #ifdef CONFIG_LPUART |
| #define CONFIG_FSL_LPUART |
| #define CONFIG_LPUART_32B_REG |
| #else |
| #define CONFIG_CONS_INDEX 1 |
| #define CONFIG_SYS_NS16550 |
| #define CONFIG_SYS_NS16550_SERIAL |
| #define CONFIG_SYS_NS16550_REG_SIZE 1 |
| #define CONFIG_SYS_NS16550_CLK get_serial_clock() |
| #endif |
| |
| #define CONFIG_BAUDRATE 115200 |
| |
| /* |
| * I2C |
| */ |
| #define CONFIG_CMD_I2C |
| #define CONFIG_SYS_I2C |
| #define CONFIG_SYS_I2C_MXC |
| #define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */ |
| #define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */ |
| #define CONFIG_SYS_I2C_MXC_I2C3 /* enable I2C bus 3 */ |
| |
| /* EEPROM */ |
| #ifndef CONFIG_SD_BOOT |
| #define CONFIG_ID_EEPROM |
| #define CONFIG_SYS_I2C_EEPROM_NXID |
| #define CONFIG_SYS_EEPROM_BUS_NUM 1 |
| #define CONFIG_SYS_I2C_EEPROM_ADDR 0x53 |
| #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 |
| #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 |
| #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5 |
| #endif |
| |
| /* |
| * MMC |
| */ |
| #define CONFIG_MMC |
| #define CONFIG_CMD_MMC |
| #define CONFIG_FSL_ESDHC |
| #define CONFIG_GENERIC_MMC |
| |
| #define CONFIG_CMD_FAT |
| #define CONFIG_DOS_PARTITION |
| |
| /* SPI */ |
| #if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI) |
| /* QSPI */ |
| #define CONFIG_FSL_QSPI |
| #define QSPI0_AMBA_BASE 0x40000000 |
| #define FSL_QSPI_FLASH_SIZE (1 << 24) |
| #define FSL_QSPI_FLASH_NUM 2 |
| #define CONFIG_SPI_FLASH_STMICRO |
| |
| /* DSPI */ |
| #define CONFIG_FSL_DSPI |
| #define CONFIG_SPI_FLASH_ATMEL |
| #endif |
| |
| /* DM SPI */ |
| #if defined(CONFIG_FSL_DSPI) || defined(CONFIG_FSL_QSPI) |
| #define CONFIG_CMD_SF |
| #define CONFIG_DM_SPI_FLASH |
| #endif |
| |
| /* |
| * Video |
| */ |
| #define CONFIG_FSL_DCU_FB |
| |
| #ifdef CONFIG_FSL_DCU_FB |
| #define CONFIG_VIDEO |
| #define CONFIG_CMD_BMP |
| #define CONFIG_CFB_CONSOLE |
| #define CONFIG_VGA_AS_SINGLE_DEVICE |
| #define CONFIG_VIDEO_LOGO |
| #define CONFIG_VIDEO_BMP_LOGO |
| |
| #define CONFIG_FSL_DCU_SII9022A |
| #define CONFIG_SYS_I2C_DVI_BUS_NUM 1 |
| #define CONFIG_SYS_I2C_DVI_ADDR 0x39 |
| #endif |
| |
| /* |
| * eTSEC |
| */ |
| #define CONFIG_TSEC_ENET |
| |
| #ifdef CONFIG_TSEC_ENET |
| #define CONFIG_MII |
| #define CONFIG_MII_DEFAULT_TSEC 1 |
| #define CONFIG_TSEC1 1 |
| #define CONFIG_TSEC1_NAME "eTSEC1" |
| #define CONFIG_TSEC2 1 |
| #define CONFIG_TSEC2_NAME "eTSEC2" |
| #define CONFIG_TSEC3 1 |
| #define CONFIG_TSEC3_NAME "eTSEC3" |
| |
| #define TSEC1_PHY_ADDR 2 |
| #define TSEC2_PHY_ADDR 0 |
| #define TSEC3_PHY_ADDR 1 |
| |
| #define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) |
| #define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) |
| #define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) |
| |
| #define TSEC1_PHYIDX 0 |
| #define TSEC2_PHYIDX 0 |
| #define TSEC3_PHYIDX 0 |
| |
| #define CONFIG_ETHPRIME "eTSEC1" |
| |
| #define CONFIG_PHY_GIGE |
| #define CONFIG_PHYLIB |
| #define CONFIG_PHY_ATHEROS |
| |
| #define CONFIG_HAS_ETH0 |
| #define CONFIG_HAS_ETH1 |
| #define CONFIG_HAS_ETH2 |
| #endif |
| |
| /* PCIe */ |
| #define CONFIG_PCI /* Enable PCI/PCIE */ |
| #define CONFIG_PCIE1 /* PCIE controler 1 */ |
| #define CONFIG_PCIE2 /* PCIE controler 2 */ |
| #define CONFIG_PCIE_LAYERSCAPE /* Use common FSL Layerscape PCIe code */ |
| #define FSL_PCIE_COMPAT "fsl,ls1021a-pcie" |
| |
| #define CONFIG_SYS_PCI_64BIT |
| |
| #define CONFIG_SYS_PCIE_CFG0_PHYS_OFF 0x00000000 |
| #define CONFIG_SYS_PCIE_CFG0_SIZE 0x00001000 /* 4k */ |
| #define CONFIG_SYS_PCIE_CFG1_PHYS_OFF 0x00001000 |
| #define CONFIG_SYS_PCIE_CFG1_SIZE 0x00001000 /* 4k */ |
| |
| #define CONFIG_SYS_PCIE_IO_BUS 0x00000000 |
| #define CONFIG_SYS_PCIE_IO_PHYS_OFF 0x00010000 |
| #define CONFIG_SYS_PCIE_IO_SIZE 0x00010000 /* 64k */ |
| |
| #define CONFIG_SYS_PCIE_MEM_BUS 0x08000000 |
| #define CONFIG_SYS_PCIE_MEM_PHYS_OFF 0x04000000 |
| #define CONFIG_SYS_PCIE_MEM_SIZE 0x08000000 /* 128M */ |
| |
| #ifdef CONFIG_PCI |
| #define CONFIG_PCI_PNP |
| #define CONFIG_PCI_SCAN_SHOW |
| #define CONFIG_CMD_PCI |
| #endif |
| |
| #define CONFIG_CMD_PING |
| #define CONFIG_CMD_DHCP |
| #define CONFIG_CMD_MII |
| |
| #define CONFIG_CMDLINE_TAG |
| #define CONFIG_CMDLINE_EDITING |
| |
| #if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI) |
| #undef CONFIG_CMD_IMLS |
| #endif |
| |
| #define CONFIG_ARMV7_NONSEC |
| #define CONFIG_ARMV7_VIRT |
| #define CONFIG_PEN_ADDR_BIG_ENDIAN |
| #define CONFIG_LS102XA_NS_ACCESS |
| #define CONFIG_SMP_PEN_ADDR 0x01ee0200 |
| #define CONFIG_TIMER_CLK_FREQ 12500000 |
| |
| #define CONFIG_HWCONFIG |
| #define HWCONFIG_BUFFER_SIZE 256 |
| |
| #define CONFIG_FSL_DEVICE_DISABLE |
| |
| #define CONFIG_BOOTDELAY 3 |
| |
| #ifdef CONFIG_LPUART |
| #define CONFIG_EXTRA_ENV_SETTINGS \ |
| "bootargs=root=/dev/ram0 rw console=ttyLP0,115200\0" \ |
| "initrd_high=0xcfffffff\0" \ |
| "fdt_high=0xcfffffff\0" |
| #else |
| #define CONFIG_EXTRA_ENV_SETTINGS \ |
| "bootargs=root=/dev/ram0 rw console=ttyS0,115200\0" \ |
| "initrd_high=0xcfffffff\0" \ |
| "fdt_high=0xcfffffff\0" |
| #endif |
| |
| /* |
| * Miscellaneous configurable options |
| */ |
| #define CONFIG_SYS_LONGHELP /* undef to save memory */ |
| #define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */ |
| #define CONFIG_SYS_PROMPT_HUSH_PS2 "> " |
| #define CONFIG_AUTO_COMPLETE |
| #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ |
| #define CONFIG_SYS_PBSIZE \ |
| (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) |
| #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ |
| #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE |
| |
| #define CONFIG_CMD_GREPENV |
| #define CONFIG_CMD_MEMINFO |
| #define CONFIG_CMD_MEMTEST |
| #define CONFIG_SYS_MEMTEST_START 0x80000000 |
| #define CONFIG_SYS_MEMTEST_END 0x9fffffff |
| |
| #define CONFIG_SYS_LOAD_ADDR 0x82000000 |
| |
| #define CONFIG_LS102XA_STREAM_ID |
| |
| /* |
| * Stack sizes |
| * The stack sizes are set up in start.S using the settings below |
| */ |
| #define CONFIG_STACKSIZE (30 * 1024) |
| |
| #define CONFIG_SYS_INIT_SP_OFFSET \ |
| (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) |
| #define CONFIG_SYS_INIT_SP_ADDR \ |
| (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET) |
| |
| #ifdef CONFIG_SPL_BUILD |
| #define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE |
| #else |
| #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ |
| #endif |
| |
| #define CONFIG_SYS_QE_FW_ADDR 0x600c0000 |
| |
| /* |
| * Environment |
| */ |
| #define CONFIG_ENV_OVERWRITE |
| |
| #if defined(CONFIG_SD_BOOT) |
| #define CONFIG_ENV_OFFSET 0x100000 |
| #define CONFIG_ENV_IS_IN_MMC |
| #define CONFIG_SYS_MMC_ENV_DEV 0 |
| #define CONFIG_ENV_SIZE 0x20000 |
| #elif defined(CONFIG_QSPI_BOOT) |
| #define CONFIG_ENV_IS_IN_SPI_FLASH |
| #define CONFIG_ENV_SIZE 0x2000 |
| #define CONFIG_ENV_OFFSET 0x100000 |
| #define CONFIG_ENV_SECT_SIZE 0x10000 |
| #else |
| #define CONFIG_ENV_IS_IN_FLASH |
| #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) |
| #define CONFIG_ENV_SIZE 0x20000 |
| #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ |
| #endif |
| |
| #define CONFIG_OF_LIBFDT |
| #define CONFIG_OF_BOARD_SETUP |
| #define CONFIG_OF_STDOUT_VIA_ALIAS |
| #define CONFIG_CMD_BOOTZ |
| |
| #define CONFIG_MISC_INIT_R |
| |
| /* Hash command with SHA acceleration supported in hardware */ |
| #define CONFIG_CMD_HASH |
| #define CONFIG_SHA_HW_ACCEL |
| |
| #ifdef CONFIG_SECURE_BOOT |
| #define CONFIG_CMD_BLOB |
| #include <asm/fsl_secure_boot.h> |
| #endif |
| |
| #endif |