include/configs/ls1046ardb.h - filogic/uboot - Gitiles

 /*
  * Copyright 2016 Freescale Semiconductor
  *
  * SPDX-License-Identifier:	GPL-2.0+
  */

 #ifndef __LS1046ARDB_H__
 #define __LS1046ARDB_H__

 #include "ls1046a_common.h"

 #ifdef CONFIG_SD_BOOT
 #define CONFIG_SYS_TEXT_BASE		0x82000000
 #else
 #define CONFIG_SYS_TEXT_BASE		0x40100000
 #endif

 #define CONFIG_SYS_CLK_FREQ		100000000
 #define CONFIG_DDR_CLK_FREQ		100000000

 #define CONFIG_LAYERSCAPE_NS_ACCESS
 #define CONFIG_MISC_INIT_R

 #define CONFIG_DIMM_SLOTS_PER_CTLR	1
 /* Physical Memory Map */
 #define CONFIG_CHIP_SELECTS_PER_CTRL	4
 #define CONFIG_NR_DRAM_BANKS		2

 #define CONFIG_DDR_SPD
 #define SPD_EEPROM_ADDRESS		0x51
 #define CONFIG_SYS_SPD_BUS_NUM		0

 #define CONFIG_DDR_ECC
 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
 #define CONFIG_MEM_INIT_VALUE           0xdeadbeef
 #define CONFIG_FSL_DDR_BIST	/* enable built-in memory test */
 #ifndef CONFIG_SPL
 #define CONFIG_FSL_DDR_INTERACTIVE	/* Interactive debugging */
 #endif

 #ifdef CONFIG_RAMBOOT_PBL
 #define CONFIG_SYS_FSL_PBL_PBI board/freescale/ls1046ardb/ls1046ardb_pbi.cfg
 #endif

 #ifdef CONFIG_SD_BOOT
 #ifdef CONFIG_EMMC_BOOT
 #define CONFIG_SYS_FSL_PBL_RCW \
 	board/freescale/ls1046ardb/ls1046ardb_rcw_emmc.cfg
 #else
 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/ls1046ardb/ls1046ardb_rcw_sd.cfg
 #endif
 #endif

 #ifndef SPL_NO_IFC
 /* IFC */
 #define CONFIG_FSL_IFC
 /*
  * NAND Flash Definitions
  */
 #define CONFIG_NAND_FSL_IFC
 #endif

 #define CONFIG_SYS_NAND_BASE		0x7e800000
 #define CONFIG_SYS_NAND_BASE_PHYS	CONFIG_SYS_NAND_BASE

 #define CONFIG_SYS_NAND_CSPR_EXT	(0x0)
 #define CONFIG_SYS_NAND_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
 				| CSPR_PORT_SIZE_8	\
 				| CSPR_MSEL_NAND	\
 				| CSPR_V)
 #define CONFIG_SYS_NAND_AMASK	IFC_AMASK(64 * 1024)
 #define CONFIG_SYS_NAND_CSOR	(CSOR_NAND_ECC_ENC_EN	/* ECC on encode */ \
 				| CSOR_NAND_ECC_DEC_EN	/* ECC on decode */ \
 				| CSOR_NAND_ECC_MODE_8	/* 8-bit ECC */ \
 				| CSOR_NAND_RAL_3	/* RAL = 3 Bytes */ \
 				| CSOR_NAND_PGS_4K	/* Page Size = 4K */ \
 				| CSOR_NAND_SPRZ_224	/* Spare size = 224 */ \
 				| CSOR_NAND_PB(64))	/* 64 Pages Per Block */

 #define CONFIG_SYS_NAND_ONFI_DETECTION

 #define CONFIG_SYS_NAND_FTIM0		(FTIM0_NAND_TCCST(0x7) | \
 					FTIM0_NAND_TWP(0x18)   | \
 					FTIM0_NAND_TWCHT(0x7) | \
 					FTIM0_NAND_TWH(0xa))
 #define CONFIG_SYS_NAND_FTIM1		(FTIM1_NAND_TADLE(0x32) | \
 					FTIM1_NAND_TWBE(0x39)  | \
 					FTIM1_NAND_TRR(0xe)   | \
 					FTIM1_NAND_TRP(0x18))
 #define CONFIG_SYS_NAND_FTIM2		(FTIM2_NAND_TRAD(0xf) | \
 					FTIM2_NAND_TREH(0xa) | \
 					FTIM2_NAND_TWHRE(0x1e))
 #define CONFIG_SYS_NAND_FTIM3		0x0

 #define CONFIG_SYS_NAND_BASE_LIST	{ CONFIG_SYS_NAND_BASE }
 #define CONFIG_SYS_MAX_NAND_DEVICE	1
 #define CONFIG_MTD_NAND_VERIFY_WRITE
 #define CONFIG_CMD_NAND

 #define CONFIG_SYS_NAND_BLOCK_SIZE	(128 * 1024)

 /*
  * CPLD
  */
 #define CONFIG_SYS_CPLD_BASE		0x7fb00000
 #define CPLD_BASE_PHYS			CONFIG_SYS_CPLD_BASE

 #define CONFIG_SYS_CPLD_CSPR_EXT	(0x0)
 #define CONFIG_SYS_CPLD_CSPR		(CSPR_PHYS_ADDR(CPLD_BASE_PHYS) | \
 					CSPR_PORT_SIZE_8 | \
 					CSPR_MSEL_GPCM | \
 					CSPR_V)
 #define CONFIG_SYS_CPLD_AMASK		IFC_AMASK(64 * 1024)
 #define CONFIG_SYS_CPLD_CSOR		CSOR_NOR_ADM_SHIFT(16)

 /* CPLD Timing parameters for IFC GPCM */
 #define CONFIG_SYS_CPLD_FTIM0		(FTIM0_GPCM_TACSE(0x0e) | \
 					FTIM0_GPCM_TEADC(0x0e) | \
 					FTIM0_GPCM_TEAHC(0x0e))
 #define CONFIG_SYS_CPLD_FTIM1		(FTIM1_GPCM_TACO(0xff) | \
 					FTIM1_GPCM_TRAD(0x3f))
 #define CONFIG_SYS_CPLD_FTIM2		(FTIM2_GPCM_TCS(0xf) | \
 					FTIM2_GPCM_TCH(0xf) | \
 					FTIM2_GPCM_TWP(0x3E))
 #define CONFIG_SYS_CPLD_FTIM3		0x0

 /* IFC Timing Params */
 #define CONFIG_SYS_CSPR0_EXT		CONFIG_SYS_NAND_CSPR_EXT
 #define CONFIG_SYS_CSPR0		CONFIG_SYS_NAND_CSPR
 #define CONFIG_SYS_AMASK0		CONFIG_SYS_NAND_AMASK
 #define CONFIG_SYS_CSOR0		CONFIG_SYS_NAND_CSOR
 #define CONFIG_SYS_CS0_FTIM0		CONFIG_SYS_NAND_FTIM0
 #define CONFIG_SYS_CS0_FTIM1		CONFIG_SYS_NAND_FTIM1
 #define CONFIG_SYS_CS0_FTIM2		CONFIG_SYS_NAND_FTIM2
 #define CONFIG_SYS_CS0_FTIM3		CONFIG_SYS_NAND_FTIM3

 #define CONFIG_SYS_CSPR2_EXT		CONFIG_SYS_CPLD_CSPR_EXT
 #define CONFIG_SYS_CSPR2		CONFIG_SYS_CPLD_CSPR
 #define CONFIG_SYS_AMASK2		CONFIG_SYS_CPLD_AMASK
 #define CONFIG_SYS_CSOR2		CONFIG_SYS_CPLD_CSOR
 #define CONFIG_SYS_CS2_FTIM0		CONFIG_SYS_CPLD_FTIM0
 #define CONFIG_SYS_CS2_FTIM1		CONFIG_SYS_CPLD_FTIM1
 #define CONFIG_SYS_CS2_FTIM2		CONFIG_SYS_CPLD_FTIM2
 #define CONFIG_SYS_CS2_FTIM3		CONFIG_SYS_CPLD_FTIM3

 /* EEPROM */
 #define CONFIG_ID_EEPROM
 #define CONFIG_SYS_I2C_EEPROM_NXID
 #define CONFIG_SYS_EEPROM_BUS_NUM		0
 #define CONFIG_SYS_I2C_EEPROM_ADDR		0x53
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		1
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	3
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	5
 #define I2C_RETIMER_ADDR			0x18

 /* PMIC */
 #define CONFIG_POWER
 #ifdef CONFIG_POWER
 #define CONFIG_POWER_I2C
 #endif

 /*
  * Environment
  */
 #ifndef SPL_NO_ENV
 #define CONFIG_ENV_OVERWRITE
 #endif

 #if defined(CONFIG_SD_BOOT)
 #define CONFIG_SYS_MMC_ENV_DEV		0
 #define CONFIG_ENV_OFFSET		(3 * 1024 * 1024)
 #define CONFIG_ENV_SIZE			0x2000
 #else
 #define CONFIG_ENV_SIZE			0x2000		/* 8KB */
 #define CONFIG_ENV_OFFSET		0x300000	/* 3MB */
 #define CONFIG_ENV_SECT_SIZE		0x40000		/* 256KB */
 #endif

 #define AQR105_IRQ_MASK			0x80000000
 /* FMan */
 #ifndef SPL_NO_FMAN

 #ifdef CONFIG_NET
 #define CONFIG_PHYLIB
 #define CONFIG_PHY_GIGE		/* Include GbE speed/duplex detection */
 #define CONFIG_PHY_REALTEK
 #endif

 #ifdef CONFIG_SYS_DPAA_FMAN
 #define CONFIG_FMAN_ENET
 #define CONFIG_PHY_AQUANTIA
 #define CONFIG_PHYLIB_10G
 #define RGMII_PHY1_ADDR			0x1
 #define RGMII_PHY2_ADDR			0x2

 #define SGMII_PHY1_ADDR			0x3
 #define SGMII_PHY2_ADDR			0x4

 #define FM1_10GEC1_PHY_ADDR		0x0

 #define CONFIG_ETHPRIME			"FM1@DTSEC3"
 #endif

 #endif

 /* QSPI device */
 #ifndef SPL_NO_QSPI
 #ifdef CONFIG_FSL_QSPI
 #define CONFIG_SPI_FLASH_SPANSION
 #define FSL_QSPI_FLASH_SIZE		(1 << 26)
 #define FSL_QSPI_FLASH_NUM		2
 #endif
 #endif

 /* USB */
 #ifndef SPL_NO_USB
 #define CONFIG_HAS_FSL_XHCI_USB
 #ifdef CONFIG_HAS_FSL_XHCI_USB
 #define CONFIG_USB_XHCI_HCD
 #define CONFIG_USB_XHCI_FSL
 #define CONFIG_USB_XHCI_DWC3
 #define CONFIG_USB_MAX_CONTROLLER_COUNT         3
 #define CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS      2
 #define CONFIG_CMD_USB
 #define CONFIG_USB_STORAGE
 #endif
 #endif

 /* SATA */
 #ifndef SPL_NO_SATA
 #define CONFIG_LIBATA
 #define CONFIG_SCSI_AHCI
 #define CONFIG_SCSI_AHCI_PLAT

 #define CONFIG_SYS_SATA				AHCI_BASE_ADDR

 #define CONFIG_SYS_SCSI_MAX_SCSI_ID		1
 #define CONFIG_SYS_SCSI_MAX_LUN			1
 #define CONFIG_SYS_SCSI_MAX_DEVICE		(CONFIG_SYS_SCSI_MAX_SCSI_ID * \
 						CONFIG_SYS_SCSI_MAX_LUN)
 #endif

 #ifndef SPL_NO_MISC
 #define CONFIG_BOOTCOMMAND		"sf probe 0:0;sf read $kernel_load" \
 					"$kernel_start $kernel_size;" \
 					"bootm $kernel_load"

 #define MTDPARTS_DEFAULT "mtdparts=1550000.quadspi:1m(rcw)," \
 			"15m(u-boot),48m(kernel.itb);" \
 			"7e800000.flash:16m(nand_uboot)," \
 			"48m(nand_kernel),448m(nand_free)"
 #endif

 #include <asm/fsl_secure_boot.h>

 #endif /* __LS1046ARDB_H__ */
	/*
	* Copyright 2016 Freescale Semiconductor
	*
	* SPDX-License-Identifier: GPL-2.0+
	*/

	#ifndef __LS1046ARDB_H__
	#define __LS1046ARDB_H__

	#include "ls1046a_common.h"

	#ifdef CONFIG_SD_BOOT
	#define CONFIG_SYS_TEXT_BASE 0x82000000
	#else
	#define CONFIG_SYS_TEXT_BASE 0x40100000
	#endif

	#define CONFIG_SYS_CLK_FREQ 100000000
	#define CONFIG_DDR_CLK_FREQ 100000000

	#define CONFIG_LAYERSCAPE_NS_ACCESS
	#define CONFIG_MISC_INIT_R

	#define CONFIG_DIMM_SLOTS_PER_CTLR 1
	/* Physical Memory Map */
	#define CONFIG_CHIP_SELECTS_PER_CTRL 4
	#define CONFIG_NR_DRAM_BANKS 2

	#define CONFIG_DDR_SPD
	#define SPD_EEPROM_ADDRESS 0x51
	#define CONFIG_SYS_SPD_BUS_NUM 0

	#define CONFIG_DDR_ECC
	#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
	#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
	#define CONFIG_FSL_DDR_BIST /* enable built-in memory test */
	#ifndef CONFIG_SPL
	#define CONFIG_FSL_DDR_INTERACTIVE /* Interactive debugging */
	#endif

	#ifdef CONFIG_RAMBOOT_PBL
	#define CONFIG_SYS_FSL_PBL_PBI board/freescale/ls1046ardb/ls1046ardb_pbi.cfg
	#endif

	#ifdef CONFIG_SD_BOOT
	#ifdef CONFIG_EMMC_BOOT
	#define CONFIG_SYS_FSL_PBL_RCW \
	board/freescale/ls1046ardb/ls1046ardb_rcw_emmc.cfg
	#else
	#define CONFIG_SYS_FSL_PBL_RCW board/freescale/ls1046ardb/ls1046ardb_rcw_sd.cfg
	#endif
	#endif

	#ifndef SPL_NO_IFC
	/* IFC */
	#define CONFIG_FSL_IFC
	/*
	* NAND Flash Definitions
	*/
	#define CONFIG_NAND_FSL_IFC
	#endif

	#define CONFIG_SYS_NAND_BASE 0x7e800000
	#define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE

	#define CONFIG_SYS_NAND_CSPR_EXT (0x0)
	#define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
	\| CSPR_PORT_SIZE_8 \
	\| CSPR_MSEL_NAND \
	\| CSPR_V)
	#define CONFIG_SYS_NAND_AMASK IFC_AMASK(64 * 1024)
	#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \
	\| CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \
	\| CSOR_NAND_ECC_MODE_8 /* 8-bit ECC */ \
	\| CSOR_NAND_RAL_3 /* RAL = 3 Bytes */ \
	\| CSOR_NAND_PGS_4K /* Page Size = 4K */ \
	\| CSOR_NAND_SPRZ_224 /* Spare size = 224 */ \
	\| CSOR_NAND_PB(64)) /* 64 Pages Per Block */

	#define CONFIG_SYS_NAND_ONFI_DETECTION

	#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x7) \| \
	FTIM0_NAND_TWP(0x18) \| \
	FTIM0_NAND_TWCHT(0x7) \| \
	FTIM0_NAND_TWH(0xa))
	#define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) \| \
	FTIM1_NAND_TWBE(0x39) \| \
	FTIM1_NAND_TRR(0xe) \| \
	FTIM1_NAND_TRP(0x18))
	#define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0xf) \| \
	FTIM2_NAND_TREH(0xa) \| \
	FTIM2_NAND_TWHRE(0x1e))
	#define CONFIG_SYS_NAND_FTIM3 0x0

	#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE }
	#define CONFIG_SYS_MAX_NAND_DEVICE 1
	#define CONFIG_MTD_NAND_VERIFY_WRITE
	#define CONFIG_CMD_NAND

	#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)

	/*
	* CPLD
	*/
	#define CONFIG_SYS_CPLD_BASE 0x7fb00000
	#define CPLD_BASE_PHYS CONFIG_SYS_CPLD_BASE

	#define CONFIG_SYS_CPLD_CSPR_EXT (0x0)
	#define CONFIG_SYS_CPLD_CSPR (CSPR_PHYS_ADDR(CPLD_BASE_PHYS) \| \
	CSPR_PORT_SIZE_8 \| \
	CSPR_MSEL_GPCM \| \
	CSPR_V)
	#define CONFIG_SYS_CPLD_AMASK IFC_AMASK(64 * 1024)
	#define CONFIG_SYS_CPLD_CSOR CSOR_NOR_ADM_SHIFT(16)

	/* CPLD Timing parameters for IFC GPCM */
	#define CONFIG_SYS_CPLD_FTIM0 (FTIM0_GPCM_TACSE(0x0e) \| \
	FTIM0_GPCM_TEADC(0x0e) \| \
	FTIM0_GPCM_TEAHC(0x0e))
	#define CONFIG_SYS_CPLD_FTIM1 (FTIM1_GPCM_TACO(0xff) \| \
	FTIM1_GPCM_TRAD(0x3f))
	#define CONFIG_SYS_CPLD_FTIM2 (FTIM2_GPCM_TCS(0xf) \| \
	FTIM2_GPCM_TCH(0xf) \| \
	FTIM2_GPCM_TWP(0x3E))
	#define CONFIG_SYS_CPLD_FTIM3 0x0

	/* IFC Timing Params */
	#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT
	#define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR
	#define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK
	#define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR
	#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0
	#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1
	#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2
	#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3

	#define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_CPLD_CSPR_EXT
	#define CONFIG_SYS_CSPR2 CONFIG_SYS_CPLD_CSPR
	#define CONFIG_SYS_AMASK2 CONFIG_SYS_CPLD_AMASK
	#define CONFIG_SYS_CSOR2 CONFIG_SYS_CPLD_CSOR
	#define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_CPLD_FTIM0
	#define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_CPLD_FTIM1
	#define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_CPLD_FTIM2
	#define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_CPLD_FTIM3

	/* EEPROM */
	#define CONFIG_ID_EEPROM
	#define CONFIG_SYS_I2C_EEPROM_NXID
	#define CONFIG_SYS_EEPROM_BUS_NUM 0
	#define CONFIG_SYS_I2C_EEPROM_ADDR 0x53
	#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
	#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
	#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
	#define I2C_RETIMER_ADDR 0x18

	/* PMIC */
	#define CONFIG_POWER
	#ifdef CONFIG_POWER
	#define CONFIG_POWER_I2C
	#endif

	/*
	* Environment
	*/
	#ifndef SPL_NO_ENV
	#define CONFIG_ENV_OVERWRITE
	#endif

	#if defined(CONFIG_SD_BOOT)
	#define CONFIG_SYS_MMC_ENV_DEV 0
	#define CONFIG_ENV_OFFSET (3 * 1024 * 1024)
	#define CONFIG_ENV_SIZE 0x2000
	#else
	#define CONFIG_ENV_SIZE 0x2000 /* 8KB */
	#define CONFIG_ENV_OFFSET 0x300000 /* 3MB */
	#define CONFIG_ENV_SECT_SIZE 0x40000 /* 256KB */
	#endif

	#define AQR105_IRQ_MASK 0x80000000
	/* FMan */
	#ifndef SPL_NO_FMAN

	#ifdef CONFIG_NET
	#define CONFIG_PHYLIB
	#define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */
	#define CONFIG_PHY_REALTEK
	#endif

	#ifdef CONFIG_SYS_DPAA_FMAN
	#define CONFIG_FMAN_ENET
	#define CONFIG_PHY_AQUANTIA
	#define CONFIG_PHYLIB_10G
	#define RGMII_PHY1_ADDR 0x1
	#define RGMII_PHY2_ADDR 0x2

	#define SGMII_PHY1_ADDR 0x3
	#define SGMII_PHY2_ADDR 0x4

	#define FM1_10GEC1_PHY_ADDR 0x0

	#define CONFIG_ETHPRIME "FM1@DTSEC3"
	#endif

	#endif

	/* QSPI device */
	#ifndef SPL_NO_QSPI
	#ifdef CONFIG_FSL_QSPI
	#define CONFIG_SPI_FLASH_SPANSION
	#define FSL_QSPI_FLASH_SIZE (1 << 26)
	#define FSL_QSPI_FLASH_NUM 2
	#endif
	#endif

	/* USB */
	#ifndef SPL_NO_USB
	#define CONFIG_HAS_FSL_XHCI_USB
	#ifdef CONFIG_HAS_FSL_XHCI_USB
	#define CONFIG_USB_XHCI_HCD
	#define CONFIG_USB_XHCI_FSL
	#define CONFIG_USB_XHCI_DWC3
	#define CONFIG_USB_MAX_CONTROLLER_COUNT 3
	#define CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS 2
	#define CONFIG_CMD_USB
	#define CONFIG_USB_STORAGE
	#endif
	#endif

	/* SATA */
	#ifndef SPL_NO_SATA
	#define CONFIG_LIBATA
	#define CONFIG_SCSI_AHCI
	#define CONFIG_SCSI_AHCI_PLAT

	#define CONFIG_SYS_SATA AHCI_BASE_ADDR

	#define CONFIG_SYS_SCSI_MAX_SCSI_ID 1
	#define CONFIG_SYS_SCSI_MAX_LUN 1
	#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
	CONFIG_SYS_SCSI_MAX_LUN)
	#endif

	#ifndef SPL_NO_MISC
	#define CONFIG_BOOTCOMMAND "sf probe 0:0;sf read $kernel_load" \
	"$kernel_start $kernel_size;" \
	"bootm $kernel_load"

	#define MTDPARTS_DEFAULT "mtdparts=1550000.quadspi:1m(rcw)," \
	"15m(u-boot),48m(kernel.itb);" \
	"7e800000.flash:16m(nand_uboot)," \
	"48m(nand_kernel),448m(nand_free)"
	#endif

	#include <asm/fsl_secure_boot.h>

	#endif /* __LS1046ARDB_H__ */