| # SPDX-License-Identifier: GPL-2.0-or-later |
| # |
| # (C) Copyright 2022 - Analog Devices, Inc. |
| # |
| # Written and/or maintained by Timesys Corporation |
| # |
| # Contact: Nathan Barrett-Morrison <nathan.morrison@timesys.com> |
| # Contact: Greg Malysa <greg.malysa@timesys.com> |
| # |
| |
| # All 32-bit platforms require SYS_ARM_CACHE_WRITETHROUGH |
| # But it is ignored if selected here, so it must be in the defconfig |
| |
| if ARCH_SC5XX |
| |
| config SYS_VENDOR |
| default "adi" |
| |
| choice |
| prompt "SC5xx SoC Select" |
| help |
| Selects which series of Analog Devices SC5xx chips to support. |
| |
| config SC57X |
| bool "SC57x series" |
| select COMMON_CLK_ADI_SC57X |
| select CPU_V7A |
| |
| config SC58X |
| bool "SC58x series" |
| select COMMON_CLK_ADI_SC58X |
| select CPU_V7A |
| |
| config SC59X |
| bool "SC59x 32-bit series" |
| select COMMON_CLK_ADI_SC594 |
| select CPU_V7A |
| select NOP_PHY |
| |
| config SC59X_64 |
| bool "SC59x 64-bit series" |
| select ARM64 |
| select COMMON_CLK_ADI_SC598 |
| select GICV3 |
| select GICV3_SUPPORT_GIC600 |
| select GIC_600_CLEAR_RDPD |
| select MMC_SDHCI_ADMA_FORCE_32BIT |
| select NOP_PHY if PHY |
| |
| endchoice |
| |
| if SC59X_64 |
| |
| choice |
| prompt "SC59x 64-bit board select" |
| |
| config TARGET_SC598_SOM_EZLITE |
| bool |
| prompt "SC598-SOM with SOMCRR-EZLITE" |
| select ADI_CARRIER_SOMCRR_EZLITE |
| |
| config TARGET_SC598_SOM_EZKIT |
| bool |
| prompt "SC598-SOM with SOMCRR-EZKIT" |
| select ADI_CARRIER_SOMCRR_EZKIT |
| |
| endchoice |
| |
| endif |
| |
| config ADI_IMAGE |
| string "ADI fitImage type" |
| help |
| The image built by the ADI ADSP Linux build system. |
| Is one of tiny, minimal, full. |
| |
| config SC_BOOT_MODE |
| int "SC5XX boot mode select" |
| default 1 |
| range 0 7 |
| help |
| Mode 0: do nothing, just idle |
| Mode 1: boot ldr out of serial flash |
| Mode 7: boot ldr over uart |
| |
| config SC_BOOT_SPI_BUS |
| int "sc5xx spi boot bus" |
| default 2 |
| range 0 4 |
| help |
| This is the SPI peripheral number to use for booting, X in the |
| expression `sf probe X:Y` |
| |
| config SC_BOOT_SPI_SSEL |
| int "sc5xx spi boot chipselect" |
| default 1 |
| range 0 6 |
| help |
| This is the SPI chip select number to use for booting, Y in the |
| expression `sf probe X:Y` |
| |
| config SC_BOOT_OSPI_BUS |
| int "sc5xx ospi boot bus" |
| default 0 |
| help |
| This is the OSPI peripheral number to use for booting, X in the |
| expression `sf probe X:Y` |
| |
| config SC_BOOT_OSPI_SSEL |
| int "sc5xx ospi boot chipselect" |
| default 0 |
| help |
| This is the OSPI chip select number to use for booting, Y in the |
| expression `sf probe X:Y` |
| |
| config SYS_BOOTM_LEN |
| hex |
| default 0x1800000 |
| |
| config SYS_FLASH_BASE |
| hex |
| default 0x60000000 |
| |
| config SYS_MALLOC_F_LEN |
| default 0x14000 |
| |
| config SYS_LOAD_ADDR |
| hex |
| default 0x0 |
| |
| config SYS_MALLOC_LEN |
| hex |
| default 1048576 |
| |
| config UART_CONSOLE |
| int |
| default 0 |
| |
| config UART4_SERIAL |
| bool |
| depends on DM_SERIAL |
| default y |
| |
| config WDT_ADI |
| bool |
| default y |
| |
| config WATCHDOG_TIMEOUT_MSECS |
| int |
| default 30000 |
| |
| config DW_PORTS |
| int |
| default 1 |
| |
| config ADI_BUG_EZKHW21 |
| bool "SC584 EZKIT phy bug workaround" |
| depends on SC58X |
| help |
| This workaround affects the SC584 EZKIT and addresses bug EZKHW21. |
| It disables gigabit ethernet mode and limits the board to 100 Mbps |
| |
| config ADI_CARRIER_SOMCRR_EZKIT |
| bool "Support the EV-SOMCRR-EZKIT" |
| depends on (SC59X || SC59X_64) |
| help |
| Say y to include support for the EV-SOMCRR-EZKIT carrier board, |
| which is compatible with the SC594 and SC598 SOMs. The EZKIT is |
| mutually incompatible with the EZLITE. |
| |
| config ADI_CARRIER_SOMCRR_EZLITE |
| bool "Support the EV-SOMCRR-EZLITE" |
| depends on (SC59X || SC59X_64) |
| help |
| Say y to include support for the EV-SOMCRR-EZLITE carrier board, |
| which is compatible with the SC594 and SC598 SOMs. The EZLITE is |
| mutually incompatible with the EZKIT. |
| |
| config ADI_SPL_FORCE_BMODE |
| int "Force the SPL to use this BMODE device during next boot stage" |
| default 0 |
| range 0 9 |
| depends on SPL |
| help |
| Force the SPL to use this BMODE device during next boot stage. |
| For example, if booting via QSPI, we can force the second stage |
| Of the boot process to use other peripherals via: |
| 1 = QSPI -> QSPI |
| 5 = QSPI -> OSPI |
| 6 = QSPI -> eMMC |
| |
| config ADI_USE_DMC0 |
| bool "Configure DMC0" |
| default y |
| help |
| During hardware initialization, channel 0 of the DMC will be |
| initialized. Select this if you have DMC0 connected to external |
| DDR memory. This is expected to be true for every board using |
| an SC5xx SoC. |
| |
| config ADI_USE_DMC1 |
| bool "Configure DMC1" |
| help |
| During hardware initialization, channel 1 of the DMC will be |
| initialized. Not all processors have a DMC1. Select this if your |
| SoC has DMC1 and you have it connected to external DDR memory. |
| |
| config ADI_USE_DDR2 |
| bool "Configure DMC for DDR2 mode" |
| help |
| Configure the DMC in DDR2 mode. The default is DDR3 and not all |
| parts may actually support DDR2. Please consult the manual for |
| the SoC that you are using to determine if DDR2 mode is supported. |
| This also requires that DDR2 memory is present on the board or it |
| will probably cause strange failure. |
| |
| menu "Clock configuration" |
| |
| config CGU0_DF_DIV |
| int "CGU0_DF_DIV" |
| range 0 1 |
| help |
| Select 0 to pass CLKIN to PLL |
| Select 1 to pass CLKIN/2 to PLL |
| |
| config CGU0_VCO_MULT |
| int "CGU0_VCO_MULT" |
| range 0 127 |
| help |
| VCO_MULT controls the MSEL (multiplier) bits in PLL_CTL |
| A value of 0 means 128 |
| |
| config CGU0_CCLK_DIV |
| int "CGU0_CCLK_DIV" |
| range 0 31 |
| help |
| CCLK_DIV controls the core clock divider |
| A value of 0 means 32 |
| CCLK = ((CLKIN / (1 + DF)) * VCO_MULT) / CCLK_DIV |
| |
| config CGU0_SCLK_DIV |
| int "CGU0_SCLK_DIV" |
| range 0 31 |
| help |
| SCLK_DIV controls the system clock divider |
| A value of 0 means 32 |
| SCLK = ((CLKIN / (1 + DF)) * VCO_MULT) / SYSCLK_DIV |
| |
| config CGU0_SCLK0_DIV |
| int "CGU0_SCLK0_DIV" |
| range 0 7 |
| help |
| A value of 0 means 8 |
| SCLK0 = SCLK / SCLK0_DIV |
| |
| config CGU0_SCLK1_DIV |
| int "CGU0_SCLK1_DIV" |
| depends on (SC57X || SC58X) |
| range 0 7 |
| help |
| A value of 0 means 8 |
| SCLK1 = SCLK / SCLK1_DIV |
| |
| config CGU0_DCLK_DIV |
| int "CGU0_DCLK_DIV" |
| range 0 31 |
| help |
| DCLK_DIV controls the DDR clock divider |
| A value of 0 means 32 |
| DCLK = ((CLKIN / (1 + DF)) * VCO_MULT) / DCLK_DIV |
| |
| config CGU0_OCLK_DIV |
| int "CGU0_OCLK_DIV" |
| range 0 127 |
| help |
| OCLK_DIV controls the output clock divider |
| A value of 0 means 128 |
| OCLK = ((CLKIN / (1 + DF)) * VCO_MULT) / OCLK_DIV |
| |
| config CGU0_DIV_S1SELEX |
| int "CGU0_DIV_S1SELEX" |
| depends on !SC57X && !SC58X |
| range 0 255 |
| help |
| CGU0 SCLK1 Extended divisor register. |
| A value of 0 means 256. |
| SCLK1 = ((CLKIN / (1 + DF)) * VCO_MULT) / DIV_S1SELEX |
| |
| config CGU0_CLKOUTSEL |
| int "CGU0_CLKOUTSEL" |
| default 0 |
| range 0 31 |
| help |
| Select signal driven through CLKOUT pin multiplexer. |
| This value varies on each SOC. Refer to |
| CGU_CLKOUTSEL.CLKOUTSEL in the Hardware Reference Manual |
| for values applicable to each SOC. |
| Commonly, values 0 and 1 select CLKIN0 or CLKIN1 respectively. |
| |
| config CGU1_PLL3_DDRCLK |
| bool "DDRCLK From 3rd PLL" |
| depends on SC59X_64 |
| help |
| 3rd PLL output is connected to DMC block when set. |
| When cleared, DDR clock is CLKO3 output of CDU. |
| |
| config CGU1_PLL3_VCO_MSEL |
| int "CGU0_PLL3_VCO_MSEL" |
| depends on CGU1_PLL3_DDRCLK |
| range 1 128 |
| help |
| PLL multiplier value for the 3rd PLL. |
| DCLK = (CLKIN * PLL3_VCO_MSEL) / PLL3_DCLK_DIV |
| |
| config CGU1_PLL3_DCLK_DIV |
| int "CGU0_PLL3_DCLK_DIV" |
| depends on CGU1_PLL3_DDRCLK |
| range 1 32 |
| help |
| PLL divider value for the 3rd PLL. |
| DCLK = (CLKIN * PLL3_VCO_MSEL) / PLL3_DCLK_DIV |
| |
| config CGU1_DF_DIV |
| int "CGU1_DF_DIV" |
| range 0 1 |
| help |
| Select 0 to pass CLKIN to PLL |
| Select 1 to pass CLKIN/2 to PLL |
| |
| config CGU1_VCO_MULT |
| int "CGU1_VCO_MULT" |
| range 0 127 |
| help |
| VCO_MULT controls the MSEL (multiplier) bits in PLL_CTL |
| A value of 0 means 128 |
| |
| config CGU1_CCLK_DIV |
| int "CGU1_CCLK_DIV" |
| range 0 31 |
| help |
| CCLK_DIV controls the core clock divider |
| A value of 0 means 32 |
| CCLK = ((CLKIN / (1 + DF)) * VCO_MULT) / CCLK_DIV |
| |
| config CGU1_SCLK_DIV |
| int "CGU1_SCLK_DIV" |
| range 0 31 |
| help |
| SCLK_DIV controls the system clock divider |
| A value of 0 means 32 |
| SCLK = ((CLKIN / (1 + DF)) * VCO_MULT) / SYSCLK_DIV |
| |
| config CGU1_SCLK0_DIV |
| int "CGU1_SCLK0_DIV" |
| depends on (SC57X || SC58X || SC59X) |
| range 0 7 |
| help |
| A value of 0 means 8 |
| SCLK0 = SCLK / SCLK0_DIV |
| |
| config CGU1_SCLK1_DIV |
| int "CGU1_SCLK1_DIV" |
| depends on (SC57X || SC58X) |
| range 0 7 |
| help |
| A value of 0 means 8 |
| SCLK1 = SCLK / SCLK1_DIV |
| |
| config CGU1_DCLK_DIV |
| int "CGU1_DCLK_DIV" |
| range 0 31 |
| help |
| DCLK_DIV controls the DDR clock divider |
| A value of 0 means 32 |
| DCLK = ((CLKIN / (1 + DF)) * VCO_MULT) / DCLK_DIV |
| |
| config CGU1_OCLK_DIV |
| int "CGU1_OCLK_DIV" |
| range 0 127 |
| help |
| OCLK_DIV controls the output clock divider |
| A value of 0 means 128 |
| OCLK = ((CLKIN / (1 + DF)) * VCO_MULT) / OCLK_DIV |
| |
| config CGU1_DIV_S0SELEX |
| int "CGU1_DIV_S0SELEX" |
| depends on !SC57X && !SC58X && !SC59X |
| range 0 255 |
| help |
| CGU1 SCLK0 Extended divisor register. |
| A value of 0 means 256. |
| SCLK0 = ((CLKIN / (1 + DF)) * VCO_MULT) / DIV_S0SELEX |
| |
| config CGU1_DIV_S1SELEX |
| int "CGU1_DIV_S1SELEX" |
| depends on !SC57X && !SC58X |
| range 0 255 |
| help |
| CGU1 SCLK1 Extended divisor register. |
| A value of 0 means 256. |
| SCLK1 = ((CLKIN / (1 + DF)) * VCO_MULT) / DIV_S1SELEX |
| |
| config CDU0_CGU1_CLKIN |
| int "CDU0 CGU1 CLKINn Select" |
| default 0 |
| range 0 1 |
| help |
| Selects source clock for CGU1. |
| 0 for CLKIN0 |
| 1 for CLKIN1 |
| |
| config CDU0_CLKO0 |
| int "CDU0_CLKO0" |
| range 1 7 |
| help |
| Clock source select. Refer to SOC Hardware Reference Manual |
| |
| config CDU0_CLKO1 |
| int "CDU0_CLKO1" |
| range 1 7 |
| help |
| Clock source select. Refer to SOC Hardware Reference Manual |
| |
| config CDU0_CLKO2 |
| int "CDU0_CLKO2" |
| range 1 7 |
| help |
| Clock source select. Refer to SOC Hardware Reference Manual |
| |
| config CDU0_CLKO3 |
| int "CDU0_CLKO3" |
| range 1 7 |
| help |
| Clock source select. Refer to SOC Hardware Reference Manual |
| |
| config CDU0_CLKO4 |
| int "CDU0_CLKO4" |
| range 1 7 |
| help |
| Clock source select. Refer to SOC Hardware Reference Manual |
| |
| config CDU0_CLKO5 |
| int "CDU0_CLKO5" |
| range 1 7 |
| help |
| Clock source select. Refer to SOC Hardware Reference Manual |
| |
| config CDU0_CLKO6 |
| int "CDU0_CLKO6" |
| range 1 7 |
| help |
| Clock source select. Refer to SOC Hardware Reference Manual |
| |
| config CDU0_CLKO7 |
| int "CDU0_CLKO7" |
| range 1 7 |
| help |
| Clock source select. Refer to SOC Hardware Reference Manual |
| |
| config CDU0_CLKO8 |
| int "CDU0_CLKO8" |
| range 1 7 |
| help |
| Clock source select. Refer to SOC Hardware Reference Manual |
| |
| config CDU0_CLKO9 |
| int "CDU0_CLKO9" |
| range 1 7 |
| help |
| Clock source select. Refer to SOC Hardware Reference Manual |
| |
| config CDU0_CLKO10 |
| int "CDU0_CLKO10" |
| range 1 7 |
| depends on (SC59X || SC59X_64) |
| help |
| Clock source select. Refer to SOC Hardware Reference Manual |
| |
| config CDU0_CLKO12 |
| int "CDU0_CLKO12" |
| range 1 7 |
| depends on (SC59X || SC59X_64) |
| help |
| Clock source select. Refer to SOC Hardware Reference Manual |
| |
| config CDU0_CLKO13 |
| int "CDU0_CLKO13" |
| range 1 7 |
| depends on SC59X_64 |
| help |
| Clock source select. Refer to SOC Hardware Reference Manual |
| |
| config CDU0_CLKO14 |
| int "CDU0_CLKO14" |
| range 1 7 |
| depends on SC59X_64 |
| help |
| Clock source select. Refer to SOC Hardware Reference Manual |
| |
| endmenu |
| |
| config ADI_GPIO |
| bool |
| default y |
| |
| config PINCTRL_ADI |
| bool |
| default y |
| |
| source "board/adi/sc598-som-ezkit/Kconfig" |
| source "board/adi/sc598-som-ezlite/Kconfig" |
| |
| endif |