| // SPDX-License-Identifier: GPL-2.0 |
| /* |
| * Copyright (C) 2021-2022 Marek Vasut <marex@denx.de> |
| */ |
| |
| #include "imx8mp.dtsi" |
| |
| / { |
| model = "DH electronics i.MX8M Plus DHCOM SoM"; |
| compatible = "dh,imx8mp-dhcom-som", "fsl,imx8mp"; |
| |
| aliases { |
| ethernet0 = &eqos; |
| ethernet1 = &fec; |
| rtc0 = &rv3032; |
| rtc1 = &snvs_rtc; |
| spi0 = &flexspi; |
| }; |
| |
| memory@40000000 { |
| device_type = "memory"; |
| /* Memory size 512 MiB..8 GiB will be filled by U-Boot */ |
| reg = <0x0 0x40000000 0 0x08000000>; |
| }; |
| |
| reg_eth_vio: regulator-eth-vio { |
| compatible = "regulator-fixed"; |
| gpio = <&ioexp 2 GPIO_ACTIVE_LOW>; |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-name = "eth_vio"; |
| vin-supply = <&buck4>; |
| }; |
| |
| reg_usdhc2_vmmc: regulator-usdhc2-vmmc { |
| compatible = "regulator-fixed"; |
| enable-active-high; |
| gpio = <&gpio2 19 0>; /* SD2_RESET */ |
| off-on-delay-us = <12000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_usdhc2_vmmc>; |
| regulator-max-microvolt = <3300000>; |
| regulator-min-microvolt = <3300000>; |
| regulator-name = "VDD_3V3_SD"; |
| startup-delay-us = <100>; |
| vin-supply = <&buck4>; |
| }; |
| |
| reg_vdd_3p3v_awo: regulator-vdd-3p3v-awo { /* VDD_3V3_AWO */ |
| compatible = "regulator-fixed"; |
| regulator-always-on; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-name = "VDD_3P3V_AWO"; |
| }; |
| |
| wlan_pwrseq: wifi-pwrseq { |
| compatible = "mmc-pwrseq-simple"; |
| reset-gpios = <&ioexp 1 GPIO_ACTIVE_LOW>; |
| }; |
| }; |
| |
| &A53_0 { |
| cpu-supply = <&buck2>; |
| }; |
| |
| &A53_1 { |
| cpu-supply = <&buck2>; |
| }; |
| |
| &A53_2 { |
| cpu-supply = <&buck2>; |
| }; |
| |
| &A53_3 { |
| cpu-supply = <&buck2>; |
| }; |
| |
| &ecspi1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_ecspi1>; |
| cs-gpios = <&gpio5 17 GPIO_ACTIVE_LOW>; |
| status = "disabled"; |
| }; |
| |
| &ecspi2 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_ecspi2>; |
| cs-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>; |
| status = "disabled"; |
| }; |
| |
| &eqos { /* First ethernet */ |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_eqos_rgmii>; |
| phy-handle = <ðphy0g>; |
| phy-mode = "rgmii-id"; |
| status = "okay"; |
| |
| mdio { |
| compatible = "snps,dwmac-mdio"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| /* Up to one of these two PHYs may be populated. */ |
| ethphy0f: ethernet-phy@0 { /* SMSC LAN8740Ai */ |
| compatible = "ethernet-phy-id0007.c110", |
| "ethernet-phy-ieee802.3-c22"; |
| interrupt-parent = <&gpio3>; |
| interrupts = <19 IRQ_TYPE_LEVEL_LOW>; |
| pinctrl-0 = <&pinctrl_ethphy0>; |
| pinctrl-names = "default"; |
| reg = <0>; |
| reset-assert-us = <1000>; |
| reset-deassert-us = <1000>; |
| reset-gpios = <&ioexp 4 GPIO_ACTIVE_LOW>; |
| /* Non-default PHY population option. */ |
| status = "disabled"; |
| }; |
| |
| ethphy0g: ethernet-phy@5 { /* Micrel KSZ9131RNXI */ |
| compatible = "ethernet-phy-id0022.1642", |
| "ethernet-phy-ieee802.3-c22"; |
| interrupt-parent = <&gpio3>; |
| interrupts = <19 IRQ_TYPE_LEVEL_LOW>; |
| micrel,led-mode = <0>; |
| pinctrl-0 = <&pinctrl_ethphy0>; |
| pinctrl-names = "default"; |
| reg = <5>; |
| reset-assert-us = <1000>; |
| reset-deassert-us = <1000>; |
| reset-gpios = <&ioexp 4 GPIO_ACTIVE_LOW>; |
| /* Default PHY population option. */ |
| status = "okay"; |
| }; |
| }; |
| }; |
| |
| &fec { /* Second ethernet */ |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_fec_rmii>; |
| phy-handle = <ðphy1f>; |
| phy-mode = "rmii"; |
| fsl,magic-packet; |
| status = "okay"; |
| |
| mdio { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| /* Up to one PHY may be populated. */ |
| ethphy1f: ethernet-phy@1 { /* SMSC LAN8740Ai */ |
| compatible = "ethernet-phy-id0007.c110", |
| "ethernet-phy-ieee802.3-c22"; |
| interrupt-parent = <&gpio4>; |
| interrupts = <3 IRQ_TYPE_LEVEL_LOW>; |
| pinctrl-0 = <&pinctrl_ethphy1>; |
| pinctrl-names = "default"; |
| reg = <1>; |
| reset-assert-us = <1000>; |
| reset-deassert-us = <1000>; |
| reset-gpios = <&gpio4 2 GPIO_ACTIVE_LOW>; |
| /* Non-default PHY population option. */ |
| status = "disabled"; |
| }; |
| }; |
| }; |
| |
| &flexcan1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_flexcan1>; |
| status = "disabled"; |
| }; |
| |
| &flexcan2 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_flexcan2>; |
| status = "disabled"; |
| }; |
| |
| &flexspi { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_flexspi>; |
| status = "okay"; |
| |
| flash@0 { /* W25Q128JWPIM */ |
| compatible = "jedec,spi-nor"; |
| reg = <0>; |
| spi-max-frequency = <80000000>; |
| spi-tx-bus-width = <4>; |
| spi-rx-bus-width = <4>; |
| }; |
| }; |
| |
| &gpio1 { |
| gpio-line-names = |
| "DHCOM-G", "", "", "", "", "DHCOM-I", "DHCOM-J", "DHCOM-L", |
| "DHCOM-B", "DHCOM-A", "", "DHCOM-H", "", "", "", "", |
| "", "", "", "", "", "", "", "", |
| "", "", "", "", "", "", "", ""; |
| }; |
| |
| &gpio2 { |
| gpio-line-names = |
| "", "", "", "", "", "", "", "", |
| "", "", "", "DHCOM-K", "", "", "", "", |
| "", "", "", "", "DHCOM-INT", "", "", "", |
| "", "", "", "", "", "", "", ""; |
| }; |
| |
| &gpio3 { |
| gpio-line-names = |
| "", "", "", "", "", "", "", "", |
| "", "", "", "", "", "", "SOM-HW0", "", |
| "", "", "", "", "", "", "SOM-MEM0", "SOM-MEM1", |
| "SOM-MEM2", "SOM-HW2", "", "", "", "", "", ""; |
| }; |
| |
| &gpio4 { |
| gpio-line-names = |
| "", "", "", "", "", "", "", "", |
| "", "", "", "", "", "", "", "", |
| "", "", "", "SOM-HW1", "", "", "", "", |
| "", "", "", "DHCOM-D", "", "", "", ""; |
| }; |
| |
| &gpio5 { |
| gpio-line-names = |
| "", "", "DHCOM-C", "", "", "", "", "", |
| "", "", "", "", "", "", "", "", |
| "", "", "", "", "", "", "DHCOM-E", "DHCOM-F", |
| "", "", "", "", "", "", "", ""; |
| }; |
| |
| &i2c3 { |
| clock-frequency = <100000>; |
| pinctrl-names = "default", "gpio"; |
| pinctrl-0 = <&pinctrl_i2c3>; |
| pinctrl-1 = <&pinctrl_i2c3_gpio>; |
| scl-gpios = <&gpio5 18 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| sda-gpios = <&gpio5 19 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| status = "okay"; |
| |
| tc_bridge: bridge@f { |
| compatible = "toshiba,tc9595", "toshiba,tc358767"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_tc9595>; |
| reg = <0xf>; |
| clock-names = "ref"; |
| clocks = <&clk IMX8MP_CLK_CLKOUT2>; |
| assigned-clocks = <&clk IMX8MP_CLK_CLKOUT2_SEL>, |
| <&clk IMX8MP_CLK_CLKOUT2>, |
| <&clk IMX8MP_AUDIO_PLL2_OUT>; |
| assigned-clock-parents = <&clk IMX8MP_AUDIO_PLL2_OUT>; |
| assigned-clock-rates = <13000000>, <13000000>, <208000000>; |
| reset-gpios = <&gpio4 1 GPIO_ACTIVE_HIGH>; |
| status = "disabled"; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| |
| tc_bridge_in: endpoint { |
| data-lanes = <1 2 3 4>; |
| remote-endpoint = <&dsi_out>; |
| }; |
| }; |
| }; |
| }; |
| |
| pmic: pmic@25 { |
| compatible = "nxp,pca9450c"; |
| reg = <0x25>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_pmic>; |
| interrupt-parent = <&gpio1>; |
| interrupts = <3 IRQ_TYPE_LEVEL_LOW>; |
| |
| /* |
| * i.MX 8M Plus Data Sheet for Consumer Products |
| * 3.1.4 Operating ranges |
| * MIMX8ML8CVNKZAB |
| */ |
| regulators { |
| buck1: BUCK1 { /* VDD_SOC (dual-phase with BUCK3) */ |
| regulator-min-microvolt = <850000>; |
| regulator-max-microvolt = <1000000>; |
| regulator-ramp-delay = <3125>; |
| regulator-always-on; |
| regulator-boot-on; |
| }; |
| |
| buck2: BUCK2 { /* VDD_ARM */ |
| nxp,dvs-run-voltage = <950000>; |
| nxp,dvs-standby-voltage = <850000>; |
| regulator-min-microvolt = <850000>; |
| regulator-max-microvolt = <1000000>; |
| regulator-ramp-delay = <3125>; |
| regulator-always-on; |
| regulator-boot-on; |
| }; |
| |
| buck4: BUCK4 { /* VDD_3V3 */ |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-always-on; |
| regulator-boot-on; |
| }; |
| |
| buck5: BUCK5 { /* VDD_1V8 */ |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-always-on; |
| regulator-boot-on; |
| }; |
| |
| buck6: BUCK6 { /* NVCC_DRAM_1V1 */ |
| regulator-min-microvolt = <1100000>; |
| regulator-max-microvolt = <1100000>; |
| regulator-always-on; |
| regulator-boot-on; |
| }; |
| |
| ldo1: LDO1 { /* NVCC_SNVS_1V8 */ |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-always-on; |
| regulator-boot-on; |
| }; |
| |
| ldo3: LDO3 { /* VDDA_1V8 */ |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-always-on; |
| regulator-boot-on; |
| }; |
| |
| ldo4: LDO4 { /* PMIC_LDO4 */ |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| }; |
| |
| ldo5: LDO5 { /* NVCC_SD2 */ |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <3300000>; |
| }; |
| }; |
| }; |
| |
| adc@48 { |
| compatible = "ti,ads1015"; |
| reg = <0x48>; |
| interrupts-extended = <&ioexp 7 IRQ_TYPE_EDGE_FALLING>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| channel@0 { /* Voltage over AIN0 and AIN1. */ |
| reg = <0>; |
| }; |
| |
| channel@1 { /* Voltage over AIN0 and AIN3. */ |
| reg = <1>; |
| }; |
| |
| channel@2 { /* Voltage over AIN1 and AIN3. */ |
| reg = <2>; |
| }; |
| |
| channel@3 { /* Voltage over AIN2 and AIN3. */ |
| reg = <3>; |
| }; |
| |
| channel@4 { /* Voltage over AIN0 and GND. */ |
| reg = <4>; |
| }; |
| |
| channel@5 { /* Voltage over AIN1 and GND. */ |
| reg = <5>; |
| }; |
| |
| channel@6 { /* Voltage over AIN2 and GND. */ |
| reg = <6>; |
| }; |
| |
| channel@7 { /* Voltage over AIN3 and GND. */ |
| reg = <7>; |
| }; |
| }; |
| |
| touchscreen@49 { |
| compatible = "ti,tsc2004"; |
| reg = <0x49>; |
| interrupts-extended = <&gpio4 0 IRQ_TYPE_EDGE_FALLING>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_touch>; |
| vio-supply = <&buck4>; |
| }; |
| |
| eeprom0: eeprom@50 { /* EEPROM with EQoS MAC address */ |
| compatible = "atmel,24c32"; /* M24C32-D */ |
| pagesize = <32>; |
| reg = <0x50>; |
| }; |
| |
| rv3032: rtc@51 { |
| compatible = "microcrystal,rv3032"; |
| reg = <0x51>; |
| interrupts-extended = <&ioexp 3 IRQ_TYPE_EDGE_FALLING>; |
| wakeup-source; |
| }; |
| |
| eeprom1: eeprom@53 { /* EEPROM with FEC MAC address */ |
| compatible = "atmel,24c32"; /* M24C32-D */ |
| pagesize = <32>; |
| reg = <0x53>; |
| }; |
| |
| eeprom0wl: eeprom@58 { |
| compatible = "atmel,24c32d-wl"; /* M24C32-D WL page of 0x50 */ |
| pagesize = <32>; |
| reg = <0x58>; |
| }; |
| |
| eeprom1wl: eeprom@5b { |
| compatible = "atmel,24c32d-wl"; /* M24C32-D WL page of 0x53 */ |
| pagesize = <32>; |
| reg = <0x5b>; |
| }; |
| |
| ioexp: gpio@74 { |
| compatible = "nxp,pca9539"; |
| reg = <0x74>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupts-extended = <&gpio3 20 IRQ_TYPE_LEVEL_LOW>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_ioexp>; |
| wakeup-source; |
| |
| gpio-line-names = |
| "BT_REG_EN", "WL_REG_EN", "VIO_SWITCHED_#EN", "RTC_#INT", |
| "ENET_QOS_#RST", "RGB_OSZ_ENABLE", "USB1_ID", "ADC_ALTER_RDY", |
| "DHCOM-W", "DHCOM-V", "DHCOM-U", "DHCOM-T", |
| "BT_HOST_WAKE", "BT_DEV_WAKE", "", ""; |
| }; |
| }; |
| |
| &i2c4 { |
| clock-frequency = <100000>; |
| pinctrl-names = "default", "gpio"; |
| pinctrl-0 = <&pinctrl_i2c4>; |
| pinctrl-1 = <&pinctrl_i2c4_gpio>; |
| scl-gpios = <&gpio5 20 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| sda-gpios = <&gpio5 21 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| status = "okay"; |
| }; |
| |
| &i2c5 { /* HDMI EDID bus */ |
| clock-frequency = <100000>; |
| pinctrl-names = "default", "gpio"; |
| pinctrl-0 = <&pinctrl_i2c5>; |
| pinctrl-1 = <&pinctrl_i2c5_gpio>; |
| scl-gpios = <&gpio3 26 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| sda-gpios = <&gpio3 27 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| status = "okay"; |
| }; |
| |
| &mipi_dsi { |
| samsung,burst-clock-frequency = <160000000>; |
| samsung,esc-clock-frequency = <10000000>; |
| |
| ports { |
| port@1 { |
| reg = <1>; |
| |
| dsi_out: endpoint { |
| data-lanes = <1 2 3 4>; |
| remote-endpoint = <&tc_bridge_in>; |
| }; |
| }; |
| }; |
| }; |
| |
| &pwm1 { |
| pinctrl-0 = <&pinctrl_pwm1>; |
| pinctrl-names = "default"; |
| status = "disabled"; |
| }; |
| |
| &uart1 { |
| /* CA53 console */ |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_uart1>; |
| status = "okay"; |
| wakeup-source; |
| }; |
| |
| &uart2 { |
| /* Bluetooth */ |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_uart2>; |
| uart-has-rtscts; |
| status = "okay"; |
| |
| /* |
| * PLL1 at 80 MHz supplies UART2 root with 80 MHz clock, |
| * which with 16x oversampling yields 5 Mbdps baud base, |
| * which can be well divided by 5/4 to achieve 4 Mbdps, |
| * which is exactly the maximum rate supported by muRata |
| * 2AE bluetooth UART. |
| */ |
| assigned-clocks = <&clk IMX8MP_CLK_UART2>; |
| assigned-clock-parents = <&clk IMX8MP_SYS_PLL1_80M>; |
| assigned-clock-rates = <80000000>; |
| |
| bluetooth { |
| compatible = "cypress,cyw4373a0-bt"; |
| shutdown-gpios = <&ioexp 0 GPIO_ACTIVE_HIGH>; |
| max-speed = <4000000>; |
| }; |
| }; |
| |
| &uart3 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_uart3>; |
| uart-has-rtscts; |
| status = "okay"; |
| }; |
| |
| &uart4 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_uart4>; |
| status = "okay"; |
| }; |
| |
| &usb3_phy0 { |
| status = "okay"; |
| }; |
| |
| &usb3_0 { |
| status = "okay"; |
| }; |
| |
| &usb_dwc3_0 { |
| dr_mode = "otg"; |
| status = "okay"; |
| }; |
| |
| &usb3_phy1 { |
| status = "okay"; |
| }; |
| |
| &usb3_1 { |
| status = "okay"; |
| }; |
| |
| &usb_dwc3_1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_usb1_vbus>; |
| dr_mode = "host"; |
| status = "okay"; |
| }; |
| |
| /* SDIO WiFi */ |
| &usdhc1 { |
| pinctrl-names = "default", "state_100mhz", "state_200mhz"; |
| pinctrl-0 = <&pinctrl_usdhc1>; |
| pinctrl-1 = <&pinctrl_usdhc1_100mhz>; |
| pinctrl-2 = <&pinctrl_usdhc1_200mhz>; |
| mmc-pwrseq = <&wlan_pwrseq>; |
| vmmc-supply = <&buck4>; |
| bus-width = <4>; |
| non-removable; |
| cap-power-off-card; |
| keep-power-in-suspend; |
| status = "okay"; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| brcmf: bcrmf@1 { /* muRata 2AE */ |
| reg = <1>; |
| compatible = "cypress,cyw4373-fmac", "brcm,bcm4329-fmac"; |
| /* |
| * The "host-wake" interrupt output is by default not |
| * connected to the SoC, but can be connected on to |
| * SoC pin on the carrier board. |
| */ |
| }; |
| }; |
| |
| /* SD slot */ |
| &usdhc2 { |
| pinctrl-names = "default", "state_100mhz", "state_200mhz"; |
| pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>; |
| pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>; |
| pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>; |
| cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>; |
| vmmc-supply = <®_usdhc2_vmmc>; |
| bus-width = <4>; |
| status = "okay"; |
| }; |
| |
| /* eMMC */ |
| &usdhc3 { |
| pinctrl-names = "default", "state_100mhz", "state_200mhz"; |
| pinctrl-0 = <&pinctrl_usdhc3>; |
| pinctrl-1 = <&pinctrl_usdhc3_100mhz>; |
| pinctrl-2 = <&pinctrl_usdhc3_200mhz>; |
| vmmc-supply = <&buck4>; |
| vqmmc-supply = <&buck5>; |
| bus-width = <8>; |
| non-removable; |
| status = "okay"; |
| }; |
| |
| &wdog1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_wdog>; |
| fsl,ext-reset-output; |
| status = "okay"; |
| }; |
| |
| &iomuxc { |
| pinctrl-0 = <&pinctrl_hog_base |
| &pinctrl_dhcom_a &pinctrl_dhcom_b &pinctrl_dhcom_c |
| &pinctrl_dhcom_d &pinctrl_dhcom_e &pinctrl_dhcom_f |
| &pinctrl_dhcom_g &pinctrl_dhcom_h &pinctrl_dhcom_i |
| &pinctrl_dhcom_j &pinctrl_dhcom_k &pinctrl_dhcom_l |
| &pinctrl_dhcom_m &pinctrl_dhcom_n &pinctrl_dhcom_o |
| &pinctrl_dhcom_p &pinctrl_dhcom_q &pinctrl_dhcom_r |
| &pinctrl_dhcom_s &pinctrl_dhcom_int>; |
| pinctrl-names = "default"; |
| |
| pinctrl_dhcom_a: dhcom-a-grp { |
| fsl,pins = < |
| /* ENET_QOS_EVENT0-OUT */ |
| MX8MP_IOMUXC_GPIO1_IO09__GPIO1_IO09 0x2 |
| >; |
| }; |
| |
| pinctrl_dhcom_b: dhcom-b-grp { |
| fsl,pins = < |
| /* ENET_QOS_EVENT0-IN */ |
| MX8MP_IOMUXC_GPIO1_IO08__GPIO1_IO08 0x2 |
| >; |
| }; |
| |
| pinctrl_dhcom_c: dhcom-c-grp { |
| fsl,pins = < |
| /* GPIO_C */ |
| MX8MP_IOMUXC_SAI3_MCLK__GPIO5_IO02 0x2 |
| >; |
| }; |
| |
| pinctrl_dhcom_d: dhcom-d-grp { |
| fsl,pins = < |
| /* GPIO_D */ |
| MX8MP_IOMUXC_SAI2_MCLK__GPIO4_IO27 0x2 |
| >; |
| }; |
| |
| pinctrl_dhcom_e: dhcom-e-grp { |
| fsl,pins = < |
| /* GPIO_E */ |
| MX8MP_IOMUXC_UART1_RXD__GPIO5_IO22 0x2 |
| >; |
| }; |
| |
| pinctrl_dhcom_f: dhcom-f-grp { |
| fsl,pins = < |
| /* GPIO_F */ |
| MX8MP_IOMUXC_UART1_TXD__GPIO5_IO23 0x2 |
| >; |
| }; |
| |
| pinctrl_dhcom_g: dhcom-g-grp { |
| fsl,pins = < |
| /* GPIO_G */ |
| MX8MP_IOMUXC_GPIO1_IO00__GPIO1_IO00 0x2 |
| >; |
| }; |
| |
| pinctrl_dhcom_h: dhcom-h-grp { |
| fsl,pins = < |
| /* GPIO_H */ |
| MX8MP_IOMUXC_GPIO1_IO11__GPIO1_IO11 0x2 |
| >; |
| }; |
| |
| pinctrl_dhcom_i: dhcom-i-grp { |
| fsl,pins = < |
| /* CSI1_SYNC */ |
| MX8MP_IOMUXC_GPIO1_IO05__GPIO1_IO05 0x2 |
| >; |
| }; |
| |
| pinctrl_dhcom_j: dhcom-j-grp { |
| fsl,pins = < |
| /* CSIx_#RST */ |
| MX8MP_IOMUXC_GPIO1_IO06__GPIO1_IO06 0x2 |
| >; |
| }; |
| |
| pinctrl_dhcom_k: dhcom-k-grp { |
| fsl,pins = < |
| /* CSIx_PWDN */ |
| MX8MP_IOMUXC_SD1_STROBE__GPIO2_IO11 0x2 |
| >; |
| }; |
| |
| pinctrl_dhcom_l: dhcom-l-grp { |
| fsl,pins = < |
| /* CSI2_SYNC */ |
| MX8MP_IOMUXC_GPIO1_IO07__GPIO1_IO07 0x2 |
| >; |
| }; |
| |
| pinctrl_dhcom_m: dhcom-m-grp { |
| fsl,pins = < |
| /* CSIx_MCLK */ |
| MX8MP_IOMUXC_SPDIF_EXT_CLK__GPIO5_IO05 0x2 |
| >; |
| }; |
| |
| pinctrl_dhcom_n: dhcom-n-grp { |
| fsl,pins = < |
| /* CSI2_D3- */ |
| MX8MP_IOMUXC_SD1_DATA7__GPIO2_IO09 0x2 |
| >; |
| }; |
| |
| pinctrl_dhcom_o: dhcom-o-grp { |
| fsl,pins = < |
| /* CSI2_D3+ */ |
| MX8MP_IOMUXC_SD1_DATA6__GPIO2_IO08 0x2 |
| >; |
| }; |
| |
| pinctrl_dhcom_p: dhcom-p-grp { |
| fsl,pins = < |
| /* CSI2_D2- */ |
| MX8MP_IOMUXC_SD1_RESET_B__GPIO2_IO10 0x2 |
| >; |
| }; |
| |
| pinctrl_dhcom_q: dhcom-q-grp { |
| fsl,pins = < |
| /* CSI2_D2+ */ |
| MX8MP_IOMUXC_GPIO1_IO13__GPIO1_IO13 0x2 |
| >; |
| }; |
| |
| pinctrl_dhcom_r: dhcom-r-grp { |
| fsl,pins = < |
| /* CSI2_D1- */ |
| MX8MP_IOMUXC_GPIO1_IO12__GPIO1_IO12 0x2 |
| >; |
| }; |
| |
| pinctrl_dhcom_s: dhcom-s-grp { |
| fsl,pins = < |
| /* CSI2_D1+ */ |
| MX8MP_IOMUXC_GPIO1_IO10__GPIO1_IO10 0x2 |
| >; |
| }; |
| |
| pinctrl_dhcom_int: dhcom-int-grp { |
| fsl,pins = < |
| /* INT_HIGHEST_PRIO */ |
| MX8MP_IOMUXC_SD2_WP__GPIO2_IO20 0x2 |
| >; |
| }; |
| |
| pinctrl_hog_base: dhcom-hog-base-grp { |
| fsl,pins = < |
| /* GPIOs for memory coding */ |
| MX8MP_IOMUXC_SAI5_RXD1__GPIO3_IO22 0x40000080 |
| MX8MP_IOMUXC_SAI5_RXD2__GPIO3_IO23 0x40000080 |
| MX8MP_IOMUXC_SAI5_RXD3__GPIO3_IO24 0x40000080 |
| /* GPIOs for hardware coding */ |
| MX8MP_IOMUXC_NAND_DQS__GPIO3_IO14 0x40000080 |
| MX8MP_IOMUXC_SAI1_TXD7__GPIO4_IO19 0x40000080 |
| MX8MP_IOMUXC_SAI5_MCLK__GPIO3_IO25 0x40000080 |
| >; |
| }; |
| |
| pinctrl_ecspi1: dhcom-ecspi1-grp { |
| fsl,pins = < |
| MX8MP_IOMUXC_I2C1_SCL__ECSPI1_SCLK 0x44 |
| MX8MP_IOMUXC_I2C1_SDA__ECSPI1_MOSI 0x44 |
| MX8MP_IOMUXC_I2C2_SCL__ECSPI1_MISO 0x44 |
| MX8MP_IOMUXC_I2C2_SDA__GPIO5_IO17 0x40 |
| >; |
| }; |
| |
| pinctrl_ecspi2: dhcom-ecspi2-grp { |
| fsl,pins = < |
| MX8MP_IOMUXC_ECSPI2_SCLK__ECSPI2_SCLK 0x44 |
| MX8MP_IOMUXC_ECSPI2_MOSI__ECSPI2_MOSI 0x44 |
| MX8MP_IOMUXC_ECSPI2_MISO__ECSPI2_MISO 0x44 |
| MX8MP_IOMUXC_ECSPI2_SS0__GPIO5_IO13 0x40 |
| >; |
| }; |
| |
| pinctrl_eqos_rgmii: dhcom-eqos-rgmii-grp { /* RGMII */ |
| fsl,pins = < |
| MX8MP_IOMUXC_ENET_MDC__ENET_QOS_MDC 0x3 |
| MX8MP_IOMUXC_ENET_MDIO__ENET_QOS_MDIO 0x3 |
| MX8MP_IOMUXC_ENET_TX_CTL__ENET_QOS_RGMII_TX_CTL 0x1f |
| MX8MP_IOMUXC_ENET_TXC__CCM_ENET_QOS_CLOCK_GENERATE_TX_CLK 0x1f |
| MX8MP_IOMUXC_ENET_TD0__ENET_QOS_RGMII_TD0 0x1f |
| MX8MP_IOMUXC_ENET_TD1__ENET_QOS_RGMII_TD1 0x1f |
| MX8MP_IOMUXC_ENET_TD2__ENET_QOS_RGMII_TD2 0x1f |
| MX8MP_IOMUXC_ENET_TD3__ENET_QOS_RGMII_TD3 0x1f |
| MX8MP_IOMUXC_ENET_RXC__CCM_ENET_QOS_CLOCK_GENERATE_RX_CLK 0x91 |
| MX8MP_IOMUXC_ENET_RX_CTL__ENET_QOS_RGMII_RX_CTL 0x91 |
| MX8MP_IOMUXC_ENET_RD0__ENET_QOS_RGMII_RD0 0x91 |
| MX8MP_IOMUXC_ENET_RD1__ENET_QOS_RGMII_RD1 0x91 |
| MX8MP_IOMUXC_ENET_RD2__ENET_QOS_RGMII_RD2 0x91 |
| MX8MP_IOMUXC_ENET_RD3__ENET_QOS_RGMII_RD3 0x91 |
| >; |
| }; |
| |
| pinctrl_eqos_rmii: dhcom-eqos-rmii-grp { /* RMII */ |
| fsl,pins = < |
| MX8MP_IOMUXC_ENET_MDC__ENET_QOS_MDC 0x3 |
| MX8MP_IOMUXC_ENET_MDIO__ENET_QOS_MDIO 0x3 |
| MX8MP_IOMUXC_ENET_TX_CTL__ENET_QOS_RGMII_TX_CTL 0x1f |
| MX8MP_IOMUXC_ENET_TD0__ENET_QOS_RGMII_TD0 0x1f |
| MX8MP_IOMUXC_ENET_TD1__ENET_QOS_RGMII_TD1 0x1f |
| MX8MP_IOMUXC_ENET_RXC__ENET_QOS_RX_ER 0x1f |
| MX8MP_IOMUXC_ENET_RX_CTL__ENET_QOS_RGMII_RX_CTL 0x91 |
| MX8MP_IOMUXC_ENET_RD0__ENET_QOS_RGMII_RD0 0x91 |
| MX8MP_IOMUXC_ENET_RD1__ENET_QOS_RGMII_RD1 0x91 |
| /* Clock */ |
| MX8MP_IOMUXC_ENET_TD2__CCM_ENET_QOS_CLOCK_GENERATE_REF_CLK 0x4000001f |
| >; |
| }; |
| |
| pinctrl_ethphy0: dhcom-ethphy0-grp { |
| fsl,pins = < |
| /* ENET_QOS_#INT Interrupt */ |
| MX8MP_IOMUXC_SAI5_RXFS__GPIO3_IO19 0x22 |
| >; |
| }; |
| |
| pinctrl_ethphy1: dhcom-ethphy1-grp { |
| fsl,pins = < |
| /* ENET1_#RST Reset */ |
| MX8MP_IOMUXC_SAI1_RXD0__GPIO4_IO02 0x11 |
| /* ENET1_#INT Interrupt */ |
| MX8MP_IOMUXC_SAI1_RXD1__GPIO4_IO03 0x11 |
| >; |
| }; |
| |
| pinctrl_fec_rgmii: dhcom-fec-rgmii-grp { /* RGMII */ |
| fsl,pins = < |
| MX8MP_IOMUXC_SAI1_MCLK__ENET1_TX_CLK 0x1f |
| MX8MP_IOMUXC_SAI1_RXD2__ENET1_MDC 0x3 |
| MX8MP_IOMUXC_SAI1_RXD3__ENET1_MDIO 0x3 |
| MX8MP_IOMUXC_SAI1_RXD4__ENET1_RGMII_RD0 0x91 |
| MX8MP_IOMUXC_SAI1_RXD5__ENET1_RGMII_RD1 0x91 |
| MX8MP_IOMUXC_SAI1_RXD6__ENET1_RGMII_RD2 0x91 |
| MX8MP_IOMUXC_SAI1_RXD7__ENET1_RGMII_RD3 0x91 |
| MX8MP_IOMUXC_SAI1_TXC__ENET1_RGMII_RXC 0x91 |
| MX8MP_IOMUXC_SAI1_TXFS__ENET1_RGMII_RX_CTL 0x91 |
| MX8MP_IOMUXC_SAI1_TXD0__ENET1_RGMII_TD0 0x1f |
| MX8MP_IOMUXC_SAI1_TXD1__ENET1_RGMII_TD1 0x1f |
| MX8MP_IOMUXC_SAI1_TXD2__ENET1_RGMII_TD2 0x1f |
| MX8MP_IOMUXC_SAI1_TXD3__ENET1_RGMII_TD3 0x1f |
| MX8MP_IOMUXC_SAI1_TXD4__ENET1_RGMII_TX_CTL 0x1f |
| MX8MP_IOMUXC_SAI1_TXD5__ENET1_RGMII_TXC 0x1f |
| MX8MP_IOMUXC_SAI1_TXD6__ENET1_RX_ER 0x1f |
| >; |
| }; |
| |
| pinctrl_fec_rmii: dhcom-fec-rmii-grp { /* RMII */ |
| fsl,pins = < |
| MX8MP_IOMUXC_SAI1_RXD2__ENET1_MDC 0x3 |
| MX8MP_IOMUXC_SAI1_RXD3__ENET1_MDIO 0x3 |
| MX8MP_IOMUXC_SAI1_RXD4__ENET1_RGMII_RD0 0x91 |
| MX8MP_IOMUXC_SAI1_RXD5__ENET1_RGMII_RD1 0x91 |
| MX8MP_IOMUXC_SAI1_TXFS__ENET1_RGMII_RX_CTL 0x91 |
| MX8MP_IOMUXC_SAI1_TXD6__ENET1_RX_ER 0x91 |
| MX8MP_IOMUXC_SAI1_TXD0__ENET1_RGMII_TD0 0x1f |
| MX8MP_IOMUXC_SAI1_TXD1__ENET1_RGMII_TD1 0x1f |
| MX8MP_IOMUXC_SAI1_TXD4__ENET1_RGMII_TX_CTL 0x1f |
| /* Clock */ |
| MX8MP_IOMUXC_SAI1_MCLK__ENET1_TX_CLK 0x4000001f |
| >; |
| }; |
| |
| pinctrl_flexcan1: dhcom-flexcan1-grp { |
| fsl,pins = < |
| MX8MP_IOMUXC_SPDIF_RX__CAN1_RX 0x154 |
| MX8MP_IOMUXC_SPDIF_TX__CAN1_TX 0x154 |
| >; |
| }; |
| |
| pinctrl_flexcan2: dhcom-flexcan2-grp { |
| fsl,pins = < |
| MX8MP_IOMUXC_UART3_RXD__CAN2_TX 0x154 |
| MX8MP_IOMUXC_UART3_TXD__CAN2_RX 0x154 |
| >; |
| }; |
| |
| pinctrl_flexspi: dhcom-flexspi-grp { |
| fsl,pins = < |
| MX8MP_IOMUXC_NAND_ALE__FLEXSPI_A_SCLK 0x1c2 |
| MX8MP_IOMUXC_NAND_CE0_B__FLEXSPI_A_SS0_B 0x82 |
| MX8MP_IOMUXC_NAND_DATA00__FLEXSPI_A_DATA00 0x82 |
| MX8MP_IOMUXC_NAND_DATA01__FLEXSPI_A_DATA01 0x82 |
| MX8MP_IOMUXC_NAND_DATA02__FLEXSPI_A_DATA02 0x82 |
| MX8MP_IOMUXC_NAND_DATA03__FLEXSPI_A_DATA03 0x82 |
| >; |
| }; |
| |
| pinctrl_hdmi: dhcom-hdmi-grp { |
| fsl,pins = < |
| MX8MP_IOMUXC_HDMI_CEC__HDMIMIX_HDMI_CEC 0x154 |
| MX8MP_IOMUXC_HDMI_HPD__HDMIMIX_HDMI_HPD 0x154 |
| >; |
| }; |
| |
| pinctrl_i2c3: dhcom-i2c3-grp { |
| fsl,pins = < |
| MX8MP_IOMUXC_I2C3_SCL__I2C3_SCL 0x40000084 |
| MX8MP_IOMUXC_I2C3_SDA__I2C3_SDA 0x40000084 |
| >; |
| }; |
| |
| pinctrl_i2c3_gpio: dhcom-i2c3-gpio-grp { |
| fsl,pins = < |
| MX8MP_IOMUXC_I2C3_SCL__GPIO5_IO18 0x84 |
| MX8MP_IOMUXC_I2C3_SDA__GPIO5_IO19 0x84 |
| >; |
| }; |
| |
| pinctrl_i2c4: dhcom-i2c4-grp { |
| fsl,pins = < |
| MX8MP_IOMUXC_I2C4_SCL__I2C4_SCL 0x40000084 |
| MX8MP_IOMUXC_I2C4_SDA__I2C4_SDA 0x40000084 |
| >; |
| }; |
| |
| pinctrl_i2c4_gpio: dhcom-i2c4-gpio-grp { |
| fsl,pins = < |
| MX8MP_IOMUXC_I2C4_SCL__GPIO5_IO20 0x84 |
| MX8MP_IOMUXC_I2C4_SDA__GPIO5_IO21 0x84 |
| >; |
| }; |
| |
| pinctrl_i2c5: dhcom-i2c5-grp { |
| fsl,pins = < |
| MX8MP_IOMUXC_HDMI_DDC_SCL__I2C5_SCL 0x40000084 |
| MX8MP_IOMUXC_HDMI_DDC_SDA__I2C5_SDA 0x40000084 |
| >; |
| }; |
| |
| pinctrl_i2c5_gpio: dhcom-i2c5-gpio-grp { |
| fsl,pins = < |
| MX8MP_IOMUXC_HDMI_DDC_SCL__GPIO3_IO26 0x84 |
| MX8MP_IOMUXC_HDMI_DDC_SDA__GPIO3_IO27 0x84 |
| >; |
| }; |
| |
| pinctrl_ioexp: dhcom-ioexp-grp { |
| fsl,pins = < |
| /* #GPIO_EXP_INT */ |
| MX8MP_IOMUXC_SAI5_RXC__GPIO3_IO20 0x22 |
| >; |
| }; |
| |
| pinctrl_pmic: dhcom-pmic-grp { |
| fsl,pins = < |
| /* PMIC_nINT */ |
| MX8MP_IOMUXC_GPIO1_IO03__GPIO1_IO03 0x40000090 |
| >; |
| }; |
| |
| pinctrl_pwm1: dhcom-pwm1-grp { |
| fsl,pins = < |
| MX8MP_IOMUXC_GPIO1_IO01__PWM1_OUT 0x6 |
| >; |
| }; |
| |
| pinctrl_tc9595: dhcom-tc9595-grp { |
| fsl,pins = < |
| /* RESET_DSIBRIDGE */ |
| MX8MP_IOMUXC_SAI1_RXC__GPIO4_IO01 0x40000146 |
| /* DSI-CONV_INT Interrupt */ |
| MX8MP_IOMUXC_SAI5_RXD0__GPIO3_IO21 0x141 |
| >; |
| }; |
| |
| pinctrl_sai3: dhcom-sai3-grp { |
| fsl,pins = < |
| MX8MP_IOMUXC_SAI3_TXFS__AUDIOMIX_SAI3_TX_SYNC 0xd6 |
| MX8MP_IOMUXC_SAI3_TXC__AUDIOMIX_SAI3_TX_BCLK 0xd6 |
| MX8MP_IOMUXC_SAI3_RXD__AUDIOMIX_SAI3_RX_DATA00 0xd6 |
| MX8MP_IOMUXC_SAI3_TXD__AUDIOMIX_SAI3_TX_DATA00 0xd6 |
| >; |
| }; |
| |
| pinctrl_touch: dhcom-touch-grp { |
| fsl,pins = < |
| /* #TOUCH_INT */ |
| MX8MP_IOMUXC_SAI1_RXFS__GPIO4_IO00 0x40000080 |
| >; |
| }; |
| |
| pinctrl_uart1: dhcom-uart1-grp { |
| fsl,pins = < |
| /* Console UART */ |
| MX8MP_IOMUXC_SAI2_RXC__UART1_DCE_RX 0x49 |
| MX8MP_IOMUXC_SAI2_RXFS__UART1_DCE_TX 0x49 |
| MX8MP_IOMUXC_SAI2_RXD0__UART1_DCE_RTS 0x49 |
| MX8MP_IOMUXC_SAI2_TXFS__UART1_DCE_CTS 0x49 |
| >; |
| }; |
| |
| pinctrl_uart2: dhcom-uart2-grp { |
| fsl,pins = < |
| /* Bluetooth UART */ |
| MX8MP_IOMUXC_UART2_RXD__UART2_DCE_RX 0x49 |
| MX8MP_IOMUXC_UART2_TXD__UART2_DCE_TX 0x49 |
| MX8MP_IOMUXC_SD1_DATA4__UART2_DCE_RTS 0x49 |
| MX8MP_IOMUXC_SD1_DATA5__UART2_DCE_CTS 0x49 |
| >; |
| }; |
| |
| pinctrl_uart3: dhcom-uart3-grp { |
| fsl,pins = < |
| MX8MP_IOMUXC_ECSPI1_SCLK__UART3_DCE_RX 0x49 |
| MX8MP_IOMUXC_ECSPI1_MOSI__UART3_DCE_TX 0x49 |
| MX8MP_IOMUXC_ECSPI1_SS0__UART3_DCE_RTS 0x49 |
| MX8MP_IOMUXC_ECSPI1_MISO__UART3_DCE_CTS 0x49 |
| >; |
| }; |
| |
| pinctrl_uart4: dhcom-uart4-grp { |
| fsl,pins = < |
| MX8MP_IOMUXC_UART4_RXD__UART4_DCE_RX 0x49 |
| MX8MP_IOMUXC_UART4_TXD__UART4_DCE_TX 0x49 |
| >; |
| }; |
| |
| pinctrl_usb1_vbus: dhcom-usb1-grp { |
| fsl,pins = < |
| MX8MP_IOMUXC_GPIO1_IO14__USB2_OTG_PWR 0x6 |
| MX8MP_IOMUXC_GPIO1_IO15__USB2_OTG_OC 0x80 |
| >; |
| }; |
| |
| pinctrl_usdhc1: dhcom-usdhc1-grp { |
| fsl,pins = < |
| MX8MP_IOMUXC_SD1_CLK__USDHC1_CLK 0x190 |
| MX8MP_IOMUXC_SD1_CMD__USDHC1_CMD 0x1d0 |
| MX8MP_IOMUXC_SD1_DATA0__USDHC1_DATA0 0x1d0 |
| MX8MP_IOMUXC_SD1_DATA1__USDHC1_DATA1 0x1d0 |
| MX8MP_IOMUXC_SD1_DATA2__USDHC1_DATA2 0x1d0 |
| MX8MP_IOMUXC_SD1_DATA3__USDHC1_DATA3 0x1d0 |
| >; |
| }; |
| |
| pinctrl_usdhc1_100mhz: dhcom-usdhc1-100mhz-grp { |
| fsl,pins = < |
| MX8MP_IOMUXC_SD1_CLK__USDHC1_CLK 0x194 |
| MX8MP_IOMUXC_SD1_CMD__USDHC1_CMD 0x1d4 |
| MX8MP_IOMUXC_SD1_DATA0__USDHC1_DATA0 0x1d4 |
| MX8MP_IOMUXC_SD1_DATA1__USDHC1_DATA1 0x1d4 |
| MX8MP_IOMUXC_SD1_DATA2__USDHC1_DATA2 0x1d4 |
| MX8MP_IOMUXC_SD1_DATA3__USDHC1_DATA3 0x1d4 |
| >; |
| }; |
| |
| pinctrl_usdhc1_200mhz: dhcom-usdhc1-200mhz-grp { |
| fsl,pins = < |
| MX8MP_IOMUXC_SD1_CLK__USDHC1_CLK 0x196 |
| MX8MP_IOMUXC_SD1_CMD__USDHC1_CMD 0x1d6 |
| MX8MP_IOMUXC_SD1_DATA0__USDHC1_DATA0 0x1d6 |
| MX8MP_IOMUXC_SD1_DATA1__USDHC1_DATA1 0x1d6 |
| MX8MP_IOMUXC_SD1_DATA2__USDHC1_DATA2 0x1d6 |
| MX8MP_IOMUXC_SD1_DATA3__USDHC1_DATA3 0x1d6 |
| >; |
| }; |
| |
| pinctrl_usdhc2: dhcom-usdhc2-grp { |
| fsl,pins = < |
| MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK 0x190 |
| MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD 0x1d0 |
| MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0 0x1d0 |
| MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1 0x1d0 |
| MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2 0x1d0 |
| MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3 0x1d0 |
| MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT 0xc1 |
| >; |
| }; |
| |
| pinctrl_usdhc2_100mhz: dhcom-usdhc2-100mhz-grp { |
| fsl,pins = < |
| MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK 0x194 |
| MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD 0x1d4 |
| MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0 0x1d4 |
| MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1 0x1d4 |
| MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2 0x1d4 |
| MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3 0x1d4 |
| MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT 0xc1 |
| >; |
| }; |
| |
| pinctrl_usdhc2_200mhz: dhcom-usdhc2-200mhz-grp { |
| fsl,pins = < |
| MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK 0x196 |
| MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD 0x1d6 |
| MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0 0x1d6 |
| MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1 0x1d6 |
| MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2 0x1d6 |
| MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3 0x1d6 |
| MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT 0xc1 |
| >; |
| }; |
| |
| pinctrl_usdhc2_vmmc: dhcom-usdhc2-vmmc-grp { |
| fsl,pins = < |
| MX8MP_IOMUXC_SD2_RESET_B__GPIO2_IO19 0x20 |
| >; |
| }; |
| |
| pinctrl_usdhc2_gpio: dhcom-usdhc2-gpio-grp { |
| fsl,pins = < |
| MX8MP_IOMUXC_SD2_CD_B__GPIO2_IO12 0x40000080 |
| >; |
| }; |
| |
| pinctrl_usdhc3: dhcom-usdhc3-grp { |
| fsl,pins = < |
| MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK 0x190 |
| MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD 0x1d0 |
| MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0 0x1d0 |
| MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1 0x1d0 |
| MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2 0x1d0 |
| MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3 0x1d0 |
| MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4 0x1d0 |
| MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5 0x1d0 |
| MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6 0x1d0 |
| MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7 0x1d0 |
| MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE 0x190 |
| MX8MP_IOMUXC_NAND_READY_B__USDHC3_RESET_B 0x141 |
| >; |
| }; |
| |
| pinctrl_usdhc3_100mhz: dhcom-usdhc3-100mhz-grp { |
| fsl,pins = < |
| MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK 0x194 |
| MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD 0x1d4 |
| MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0 0x1d4 |
| MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1 0x1d4 |
| MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2 0x1d4 |
| MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3 0x1d4 |
| MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4 0x1d4 |
| MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5 0x1d4 |
| MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6 0x1d4 |
| MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7 0x1d4 |
| MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE 0x194 |
| MX8MP_IOMUXC_NAND_READY_B__USDHC3_RESET_B 0x141 |
| >; |
| }; |
| |
| pinctrl_usdhc3_200mhz: dhcom-usdhc3-200mhz-grp { |
| fsl,pins = < |
| MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK 0x196 |
| MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD 0x1d6 |
| MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0 0x1d6 |
| MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1 0x1d6 |
| MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2 0x1d6 |
| MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3 0x1d6 |
| MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4 0x1d6 |
| MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5 0x1d6 |
| MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6 0x1d6 |
| MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7 0x1d6 |
| MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE 0x196 |
| MX8MP_IOMUXC_NAND_READY_B__USDHC3_RESET_B 0x141 |
| >; |
| }; |
| |
| pinctrl_wdog: dhcom-wdog-grp { |
| fsl,pins = < |
| MX8MP_IOMUXC_GPIO1_IO02__WDOG1_WDOG_B 0xc6 |
| >; |
| }; |
| }; |