| /* |
| * Copyright 2011-2012 Freescale Semiconductor, Inc. |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| /* |
| * P2041 RDB board configuration file |
| * Also supports P2040 RDB |
| */ |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| #define CONFIG_P2041RDB |
| #define CONFIG_PPC_P2041 |
| |
| #ifdef CONFIG_RAMBOOT_PBL |
| #define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE |
| #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc |
| #define CONFIG_SYS_FSL_PBL_PBI board/freescale/corenet_ds/pbi.cfg |
| #define CONFIG_SYS_FSL_PBL_RCW board/freescale/corenet_ds/rcw_p2041rdb.cfg |
| #endif |
| |
| #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE |
| /* Set 1M boot space */ |
| #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000) |
| #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \ |
| (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR) |
| #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc |
| #define CONFIG_SYS_NO_FLASH |
| #endif |
| |
| /* High Level Configuration Options */ |
| #define CONFIG_BOOKE |
| #define CONFIG_E500 /* BOOKE e500 family */ |
| #define CONFIG_E500MC /* BOOKE e500mc family */ |
| #define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */ |
| #define CONFIG_MP /* support multiple processors */ |
| |
| #ifndef CONFIG_SYS_TEXT_BASE |
| #define CONFIG_SYS_TEXT_BASE 0xeff40000 |
| #endif |
| |
| #ifndef CONFIG_RESET_VECTOR_ADDRESS |
| #define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc |
| #endif |
| |
| #define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */ |
| #define CONFIG_SYS_NUM_CPC CONFIG_NUM_DDR_CONTROLLERS |
| #define CONFIG_FSL_ELBC /* Has Enhanced localbus controller */ |
| #define CONFIG_FSL_CAAM /* Enable SEC/CAAM */ |
| #define CONFIG_PCI /* Enable PCI/PCIE */ |
| #define CONFIG_PCIE1 /* PCIE controller 1 */ |
| #define CONFIG_PCIE2 /* PCIE controller 2 */ |
| #define CONFIG_PCIE3 /* PCIE controller 3 */ |
| #define CONFIG_FSL_PCI_INIT /* Use common FSL init code */ |
| #define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */ |
| |
| #define CONFIG_SYS_SRIO |
| #define CONFIG_SRIO1 /* SRIO port 1 */ |
| #define CONFIG_SRIO2 /* SRIO port 2 */ |
| #define CONFIG_SRIO_PCIE_BOOT_MASTER |
| #define CONFIG_SYS_DPAA_RMAN /* RMan */ |
| |
| #define CONFIG_FSL_LAW /* Use common FSL init code */ |
| |
| #define CONFIG_ENV_OVERWRITE |
| |
| #ifdef CONFIG_SYS_NO_FLASH |
| #if !defined(CONFIG_RAMBOOT_PBL) && !defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) |
| #define CONFIG_ENV_IS_NOWHERE |
| #endif |
| #else |
| #define CONFIG_FLASH_CFI_DRIVER |
| #define CONFIG_SYS_FLASH_CFI |
| #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE |
| #endif |
| |
| #if defined(CONFIG_SPIFLASH) |
| #define CONFIG_SYS_EXTRA_ENV_RELOC |
| #define CONFIG_ENV_IS_IN_SPI_FLASH |
| #define CONFIG_ENV_SPI_BUS 0 |
| #define CONFIG_ENV_SPI_CS 0 |
| #define CONFIG_ENV_SPI_MAX_HZ 10000000 |
| #define CONFIG_ENV_SPI_MODE 0 |
| #define CONFIG_ENV_SIZE 0x2000 /* 8KB */ |
| #define CONFIG_ENV_OFFSET 0x100000 /* 1MB */ |
| #define CONFIG_ENV_SECT_SIZE 0x10000 |
| #elif defined(CONFIG_SDCARD) |
| #define CONFIG_SYS_EXTRA_ENV_RELOC |
| #define CONFIG_ENV_IS_IN_MMC |
| #define CONFIG_FSL_FIXED_MMC_LOCATION |
| #define CONFIG_SYS_MMC_ENV_DEV 0 |
| #define CONFIG_ENV_SIZE 0x2000 |
| #define CONFIG_ENV_OFFSET (512 * 1658) |
| #elif defined(CONFIG_NAND) |
| #define CONFIG_SYS_EXTRA_ENV_RELOC |
| #define CONFIG_ENV_IS_IN_NAND |
| #define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE |
| #define CONFIG_ENV_OFFSET (7 * CONFIG_SYS_NAND_BLOCK_SIZE) |
| #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) |
| #define CONFIG_ENV_IS_IN_REMOTE |
| #define CONFIG_ENV_ADDR 0xffe20000 |
| #define CONFIG_ENV_SIZE 0x2000 |
| #elif defined(CONFIG_ENV_IS_NOWHERE) |
| #define CONFIG_ENV_SIZE 0x2000 |
| #else |
| #define CONFIG_ENV_IS_IN_FLASH |
| #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE \ |
| - CONFIG_ENV_SECT_SIZE) |
| #define CONFIG_ENV_SIZE 0x2000 |
| #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ |
| #endif |
| |
| #ifndef __ASSEMBLY__ |
| unsigned long get_board_sys_clk(unsigned long dummy); |
| #endif |
| #define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) |
| |
| /* |
| * These can be toggled for performance analysis, otherwise use default. |
| */ |
| #define CONFIG_SYS_CACHE_STASHING |
| #define CONFIG_BACKSIDE_L2_CACHE |
| #define CONFIG_SYS_INIT_L2CSR0 L2CSR0_L2E |
| #define CONFIG_BTB /* toggle branch predition */ |
| |
| #define CONFIG_ENABLE_36BIT_PHYS |
| |
| #ifdef CONFIG_PHYS_64BIT |
| #define CONFIG_ADDR_MAP |
| #define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */ |
| #endif |
| |
| #define CONFIG_POST CONFIG_SYS_POST_MEMORY /* test POST memory test */ |
| #define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */ |
| #define CONFIG_SYS_MEMTEST_END 0x00400000 |
| #define CONFIG_SYS_ALT_MEMTEST |
| #define CONFIG_PANIC_HANG /* do not reset board on panic */ |
| |
| /* |
| * Config the L3 Cache as L3 SRAM |
| */ |
| #define CONFIG_SYS_INIT_L3_ADDR CONFIG_RAMBOOT_TEXT_BASE |
| #ifdef CONFIG_PHYS_64BIT |
| #define CONFIG_SYS_INIT_L3_ADDR_PHYS (0xf00000000ull | \ |
| CONFIG_RAMBOOT_TEXT_BASE) |
| #else |
| #define CONFIG_SYS_INIT_L3_ADDR_PHYS CONFIG_SYS_INIT_L3_ADDR |
| #endif |
| #define CONFIG_SYS_L3_SIZE (1024 << 10) |
| #define CONFIG_SYS_INIT_L3_END (CONFIG_SYS_INIT_L3_ADDR + CONFIG_SYS_L3_SIZE) |
| |
| #ifdef CONFIG_PHYS_64BIT |
| #define CONFIG_SYS_DCSRBAR 0xf0000000 |
| #define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull |
| #endif |
| |
| /* EEPROM */ |
| #define CONFIG_ID_EEPROM |
| #define CONFIG_SYS_I2C_EEPROM_NXID |
| #define CONFIG_SYS_EEPROM_BUS_NUM 0 |
| #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 |
| #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 |
| |
| /* |
| * DDR Setup |
| */ |
| #define CONFIG_VERY_BIG_RAM |
| #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 |
| #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE |
| |
| #define CONFIG_DIMM_SLOTS_PER_CTLR 1 |
| #define CONFIG_CHIP_SELECTS_PER_CTRL (4 * CONFIG_DIMM_SLOTS_PER_CTLR) |
| |
| #define CONFIG_DDR_SPD |
| #define CONFIG_SYS_FSL_DDR3 |
| |
| #define CONFIG_SYS_SPD_BUS_NUM 0 |
| #define SPD_EEPROM_ADDRESS 0x52 |
| #define CONFIG_SYS_SDRAM_SIZE 4096 /* for fixed parameter use */ |
| |
| /* |
| * Local Bus Definitions |
| */ |
| |
| /* Set the local bus clock 1/8 of platform clock */ |
| #define CONFIG_SYS_LBC_LCRR LCRR_CLKDIV_8 |
| |
| /* |
| * This board doesn't have a promjet connector. |
| * However, it uses commone corenet board LAW and TLB. |
| * It is necessary to use the same start address with proper offset. |
| */ |
| #define CONFIG_SYS_FLASH_BASE 0xe0000000 |
| #ifdef CONFIG_PHYS_64BIT |
| #define CONFIG_SYS_FLASH_BASE_PHYS 0xfe0000000ull |
| #else |
| #define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE |
| #endif |
| |
| #define CONFIG_SYS_FLASH_BR_PRELIM \ |
| (BR_PHYS_ADDR((CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000)) | \ |
| BR_PS_16 | BR_V) |
| #define CONFIG_SYS_FLASH_OR_PRELIM \ |
| ((0xf8000ff7 & ~OR_GPCM_SCY & ~OR_GPCM_EHTR) \ |
| | OR_GPCM_SCY_8 | OR_GPCM_EHTR_CLEAR) |
| |
| #define CONFIG_FSL_CPLD |
| #define CPLD_BASE 0xffdf0000 /* CPLD registers */ |
| #ifdef CONFIG_PHYS_64BIT |
| #define CPLD_BASE_PHYS 0xfffdf0000ull |
| #else |
| #define CPLD_BASE_PHYS CPLD_BASE |
| #endif |
| |
| #define CONFIG_SYS_BR3_PRELIM (BR_PHYS_ADDR(CPLD_BASE_PHYS) | BR_PS_8 | BR_V) |
| #define CONFIG_SYS_OR3_PRELIM 0xffffeff7 /* 32KB but only 4k mapped */ |
| |
| #define PIXIS_LBMAP_SWITCH 7 |
| #define PIXIS_LBMAP_MASK 0xf0 |
| #define PIXIS_LBMAP_SHIFT 4 |
| #define PIXIS_LBMAP_ALTBANK 0x40 |
| |
| #define CONFIG_SYS_FLASH_QUIET_TEST |
| #define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ |
| |
| #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ |
| #define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ |
| #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Erase Timeout (ms) */ |
| #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Write Timeout (ms) */ |
| |
| #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE |
| |
| #if defined(CONFIG_RAMBOOT_PBL) |
| #define CONFIG_SYS_RAMBOOT |
| #endif |
| |
| #define CONFIG_NAND_FSL_ELBC |
| /* Nand Flash */ |
| #ifdef CONFIG_NAND_FSL_ELBC |
| #define CONFIG_SYS_NAND_BASE 0xffa00000 |
| #ifdef CONFIG_PHYS_64BIT |
| #define CONFIG_SYS_NAND_BASE_PHYS 0xfffa00000ull |
| #else |
| #define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE |
| #endif |
| |
| #define CONFIG_SYS_NAND_BASE_LIST {CONFIG_SYS_NAND_BASE} |
| #define CONFIG_SYS_MAX_NAND_DEVICE 1 |
| #define CONFIG_CMD_NAND |
| #define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024) |
| |
| /* NAND flash config */ |
| #define CONFIG_SYS_NAND_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ |
| | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \ |
| | BR_PS_8 /* Port Size = 8 bit */ \ |
| | BR_MS_FCM /* MSEL = FCM */ \ |
| | BR_V) /* valid */ |
| #define CONFIG_SYS_NAND_OR_PRELIM (0xFFFC0000 /* length 256K */ \ |
| | OR_FCM_PGS /* Large Page*/ \ |
| | OR_FCM_CSCT \ |
| | OR_FCM_CST \ |
| | OR_FCM_CHT \ |
| | OR_FCM_SCY_1 \ |
| | OR_FCM_TRLX \ |
| | OR_FCM_EHTR) |
| |
| #ifdef CONFIG_NAND |
| #define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */ |
| #define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */ |
| #define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_FLASH_BR_PRELIM /* NOR Base Address */ |
| #define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_FLASH_OR_PRELIM /* NOR Options */ |
| #else |
| #define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_FLASH_BR_PRELIM /* NOR Base Address */ |
| #define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_FLASH_OR_PRELIM /* NOR Options */ |
| #define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */ |
| #define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */ |
| #endif |
| #else |
| #define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_FLASH_BR_PRELIM /* NOR Base Address */ |
| #define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_FLASH_OR_PRELIM /* NOR Options */ |
| #endif /* CONFIG_NAND_FSL_ELBC */ |
| |
| #define CONFIG_SYS_FLASH_EMPTY_INFO |
| #define CONFIG_SYS_FLASH_AMD_CHECK_DQ7 |
| #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000} |
| |
| #define CONFIG_BOARD_EARLY_INIT_F |
| #define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */ |
| #define CONFIG_MISC_INIT_R |
| |
| #define CONFIG_HWCONFIG |
| |
| /* define to use L1 as initial stack */ |
| #define CONFIG_L1_INIT_RAM |
| #define CONFIG_SYS_INIT_RAM_LOCK |
| #define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* Initial L1 address */ |
| #ifdef CONFIG_PHYS_64BIT |
| #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf |
| #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR |
| /* The assembler doesn't like typecast */ |
| #define CONFIG_SYS_INIT_RAM_ADDR_PHYS \ |
| ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \ |
| CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW) |
| #else |
| #define CONFIG_SYS_INIT_RAM_ADDR_PHYS CONFIG_SYS_INIT_RAM_ADDR |
| #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0 |
| #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS |
| #endif |
| #define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 |
| |
| #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ |
| GENERATED_GBL_DATA_SIZE) |
| #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET |
| |
| #define CONFIG_SYS_MONITOR_LEN (768 * 1024) |
| #define CONFIG_SYS_MALLOC_LEN (1024 * 1024) |
| |
| /* Serial Port - controlled on board with jumper J8 |
| * open - index 2 |
| * shorted - index 1 |
| */ |
| #define CONFIG_CONS_INDEX 1 |
| #define CONFIG_SYS_NS16550_SERIAL |
| #define CONFIG_SYS_NS16550_REG_SIZE 1 |
| #define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2) |
| |
| #define CONFIG_SYS_BAUDRATE_TABLE \ |
| {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} |
| |
| #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500) |
| #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600) |
| #define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500) |
| #define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600) |
| |
| /* I2C */ |
| #define CONFIG_SYS_I2C |
| #define CONFIG_SYS_I2C_FSL |
| #define CONFIG_SYS_FSL_I2C_SPEED 400000 |
| #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F |
| #define CONFIG_SYS_FSL_I2C_OFFSET 0x118000 |
| #define CONFIG_SYS_FSL_I2C2_SPEED 400000 |
| #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F |
| #define CONFIG_SYS_FSL_I2C2_OFFSET 0x118100 |
| |
| /* |
| * RapidIO |
| */ |
| #define CONFIG_SYS_SRIO1_MEM_VIRT 0xa0000000 |
| #ifdef CONFIG_PHYS_64BIT |
| #define CONFIG_SYS_SRIO1_MEM_PHYS 0xc20000000ull |
| #else |
| #define CONFIG_SYS_SRIO1_MEM_PHYS 0xa0000000 |
| #endif |
| #define CONFIG_SYS_SRIO1_MEM_SIZE 0x10000000 /* 256M */ |
| |
| #define CONFIG_SYS_SRIO2_MEM_VIRT 0xb0000000 |
| #ifdef CONFIG_PHYS_64BIT |
| #define CONFIG_SYS_SRIO2_MEM_PHYS 0xc30000000ull |
| #else |
| #define CONFIG_SYS_SRIO2_MEM_PHYS 0xb0000000 |
| #endif |
| #define CONFIG_SYS_SRIO2_MEM_SIZE 0x10000000 /* 256M */ |
| |
| /* |
| * for slave u-boot IMAGE instored in master memory space, |
| * PHYS must be aligned based on the SIZE |
| */ |
| #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef200000ull |
| #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff00000ull |
| #define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x100000 /* 1M */ |
| #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff00000ull |
| /* |
| * for slave UCODE and ENV instored in master memory space, |
| * PHYS must be aligned based on the SIZE |
| */ |
| #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef100000ull |
| #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull |
| #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000 /* 256K */ |
| |
| /* slave core release by master*/ |
| #define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4 |
| #define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */ |
| |
| /* |
| * SRIO_PCIE_BOOT - SLAVE |
| */ |
| #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE |
| #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000 |
| #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \ |
| (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR) |
| #endif |
| |
| /* |
| * eSPI - Enhanced SPI |
| */ |
| #define CONFIG_SF_DEFAULT_SPEED 10000000 |
| #define CONFIG_SF_DEFAULT_MODE 0 |
| |
| /* |
| * General PCI |
| * Memory space is mapped 1-1, but I/O space must start from 0. |
| */ |
| |
| /* controller 1, direct to uli, tgtid 3, Base address 20000 */ |
| #define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000 |
| #ifdef CONFIG_PHYS_64BIT |
| #define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000 |
| #define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull |
| #else |
| #define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000 |
| #define CONFIG_SYS_PCIE1_MEM_PHYS 0x80000000 |
| #endif |
| #define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ |
| #define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000 |
| #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 |
| #ifdef CONFIG_PHYS_64BIT |
| #define CONFIG_SYS_PCIE1_IO_PHYS 0xff8000000ull |
| #else |
| #define CONFIG_SYS_PCIE1_IO_PHYS 0xf8000000 |
| #endif |
| #define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ |
| |
| /* controller 2, Slot 2, tgtid 2, Base address 201000 */ |
| #define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000 |
| #ifdef CONFIG_PHYS_64BIT |
| #define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000 |
| #define CONFIG_SYS_PCIE2_MEM_PHYS 0xc20000000ull |
| #else |
| #define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000 |
| #define CONFIG_SYS_PCIE2_MEM_PHYS 0xa0000000 |
| #endif |
| #define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */ |
| #define CONFIG_SYS_PCIE2_IO_VIRT 0xf8010000 |
| #define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 |
| #ifdef CONFIG_PHYS_64BIT |
| #define CONFIG_SYS_PCIE2_IO_PHYS 0xff8010000ull |
| #else |
| #define CONFIG_SYS_PCIE2_IO_PHYS 0xf8010000 |
| #endif |
| #define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */ |
| |
| /* controller 3, Slot 1, tgtid 1, Base address 202000 */ |
| #define CONFIG_SYS_PCIE3_MEM_VIRT 0xc0000000 |
| #ifdef CONFIG_PHYS_64BIT |
| #define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000 |
| #define CONFIG_SYS_PCIE3_MEM_PHYS 0xc40000000ull |
| #else |
| #define CONFIG_SYS_PCIE3_MEM_BUS 0xc0000000 |
| #define CONFIG_SYS_PCIE3_MEM_PHYS 0xc0000000 |
| #endif |
| #define CONFIG_SYS_PCIE3_MEM_SIZE 0x20000000 /* 512M */ |
| #define CONFIG_SYS_PCIE3_IO_VIRT 0xf8020000 |
| #define CONFIG_SYS_PCIE3_IO_BUS 0x00000000 |
| #ifdef CONFIG_PHYS_64BIT |
| #define CONFIG_SYS_PCIE3_IO_PHYS 0xff8020000ull |
| #else |
| #define CONFIG_SYS_PCIE3_IO_PHYS 0xf8020000 |
| #endif |
| #define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */ |
| |
| /* Qman/Bman */ |
| #define CONFIG_SYS_DPAA_QBMAN /* Support Q/Bman */ |
| #define CONFIG_SYS_BMAN_NUM_PORTALS 10 |
| #define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000 |
| #ifdef CONFIG_PHYS_64BIT |
| #define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull |
| #else |
| #define CONFIG_SYS_BMAN_MEM_PHYS CONFIG_SYS_BMAN_MEM_BASE |
| #endif |
| #define CONFIG_SYS_BMAN_MEM_SIZE 0x00200000 |
| #define CONFIG_SYS_BMAN_SP_CENA_SIZE 0x4000 |
| #define CONFIG_SYS_BMAN_SP_CINH_SIZE 0x1000 |
| #define CONFIG_SYS_BMAN_CENA_BASE CONFIG_SYS_BMAN_MEM_BASE |
| #define CONFIG_SYS_BMAN_CENA_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1) |
| #define CONFIG_SYS_BMAN_CINH_BASE (CONFIG_SYS_BMAN_MEM_BASE + \ |
| CONFIG_SYS_BMAN_CENA_SIZE) |
| #define CONFIG_SYS_BMAN_CINH_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1) |
| #define CONFIG_SYS_BMAN_SWP_ISDR_REG 0xE08 |
| #define CONFIG_SYS_QMAN_NUM_PORTALS 10 |
| #define CONFIG_SYS_QMAN_MEM_BASE 0xf4200000 |
| #ifdef CONFIG_PHYS_64BIT |
| #define CONFIG_SYS_QMAN_MEM_PHYS 0xff4200000ull |
| #else |
| #define CONFIG_SYS_QMAN_MEM_PHYS CONFIG_SYS_QMAN_MEM_BASE |
| #endif |
| #define CONFIG_SYS_QMAN_MEM_SIZE 0x00200000 |
| #define CONFIG_SYS_QMAN_SP_CENA_SIZE 0x4000 |
| #define CONFIG_SYS_QMAN_SP_CINH_SIZE 0x1000 |
| #define CONFIG_SYS_QMAN_CENA_BASE CONFIG_SYS_QMAN_MEM_BASE |
| #define CONFIG_SYS_QMAN_CENA_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1) |
| #define CONFIG_SYS_QMAN_CINH_BASE (CONFIG_SYS_QMAN_MEM_BASE + \ |
| CONFIG_SYS_QMAN_CENA_SIZE) |
| #define CONFIG_SYS_QMAN_CINH_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1) |
| #define CONFIG_SYS_QMAN_SWP_ISDR_REG 0xE08 |
| |
| #define CONFIG_SYS_DPAA_FMAN |
| #define CONFIG_SYS_DPAA_PME |
| /* Default address of microcode for the Linux Fman driver */ |
| #if defined(CONFIG_SPIFLASH) |
| /* |
| * env is stored at 0x100000, sector size is 0x10000, ucode is stored after |
| * env, so we got 0x110000. |
| */ |
| #define CONFIG_SYS_QE_FW_IN_SPIFLASH |
| #define CONFIG_SYS_FMAN_FW_ADDR 0x110000 |
| #elif defined(CONFIG_SDCARD) |
| /* |
| * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is |
| * about 825KB (1650 blocks), Env is stored after the image, and the env size is |
| * 0x2000 (16 blocks), 8 + 1650 + 16 = 1674, enlarge it to 1680. |
| */ |
| #define CONFIG_SYS_QE_FMAN_FW_IN_MMC |
| #define CONFIG_SYS_FMAN_FW_ADDR (512 * 1680) |
| #elif defined(CONFIG_NAND) |
| #define CONFIG_SYS_QE_FMAN_FW_IN_NAND |
| #define CONFIG_SYS_FMAN_FW_ADDR (8 * CONFIG_SYS_NAND_BLOCK_SIZE) |
| #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) |
| /* |
| * Slave has no ucode locally, it can fetch this from remote. When implementing |
| * in two corenet boards, slave's ucode could be stored in master's memory |
| * space, the address can be mapped from slave TLB->slave LAW-> |
| * slave SRIO or PCIE outbound window->master inbound window-> |
| * master LAW->the ucode address in master's memory space. |
| */ |
| #define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE |
| #define CONFIG_SYS_FMAN_FW_ADDR 0xFFE00000 |
| #else |
| #define CONFIG_SYS_QE_FMAN_FW_IN_NOR |
| #define CONFIG_SYS_FMAN_FW_ADDR 0xEFF00000 |
| #endif |
| #define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000 |
| #define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH) |
| |
| #ifdef CONFIG_SYS_DPAA_FMAN |
| #define CONFIG_FMAN_ENET |
| #define CONFIG_PHYLIB_10G |
| #define CONFIG_PHY_VITESSE |
| #define CONFIG_PHY_TERANETICS |
| #endif |
| |
| #ifdef CONFIG_PCI |
| #define CONFIG_PCI_INDIRECT_BRIDGE |
| #define CONFIG_PCI_PNP /* do pci plug-and-play */ |
| |
| #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ |
| #define CONFIG_DOS_PARTITION |
| #endif /* CONFIG_PCI */ |
| |
| /* SATA */ |
| #define CONFIG_FSL_SATA_V2 |
| |
| #ifdef CONFIG_FSL_SATA_V2 |
| #define CONFIG_FSL_SATA |
| #define CONFIG_LIBATA |
| |
| #define CONFIG_SYS_SATA_MAX_DEVICE 2 |
| #define CONFIG_SATA1 |
| #define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR |
| #define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA |
| #define CONFIG_SATA2 |
| #define CONFIG_SYS_SATA2 CONFIG_SYS_MPC85xx_SATA2_ADDR |
| #define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA |
| |
| #define CONFIG_LBA48 |
| #define CONFIG_CMD_SATA |
| #define CONFIG_DOS_PARTITION |
| #endif |
| |
| #ifdef CONFIG_FMAN_ENET |
| #define CONFIG_SYS_FM1_DTSEC1_PHY_ADDR 0x2 |
| #define CONFIG_SYS_FM1_DTSEC2_PHY_ADDR 0x3 |
| #define CONFIG_SYS_FM1_DTSEC3_PHY_ADDR 0x4 |
| #define CONFIG_SYS_FM1_DTSEC4_PHY_ADDR 0x1 |
| #define CONFIG_SYS_FM1_DTSEC5_PHY_ADDR 0x0 |
| |
| #define CONFIG_SYS_FM1_DTSEC1_RISER_PHY_ADDR 0x1c |
| #define CONFIG_SYS_FM1_DTSEC2_RISER_PHY_ADDR 0x1d |
| #define CONFIG_SYS_FM1_DTSEC3_RISER_PHY_ADDR 0x1e |
| #define CONFIG_SYS_FM1_DTSEC4_RISER_PHY_ADDR 0x1f |
| |
| #define CONFIG_SYS_FM1_10GEC1_PHY_ADDR 0 |
| |
| #define CONFIG_SYS_TBIPA_VALUE 8 |
| #define CONFIG_MII /* MII PHY management */ |
| #define CONFIG_ETHPRIME "FM1@DTSEC1" |
| #define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */ |
| #endif |
| |
| /* |
| * Environment |
| */ |
| #define CONFIG_LOADS_ECHO /* echo on for serial download */ |
| #define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */ |
| |
| /* |
| * Command line configuration. |
| */ |
| #define CONFIG_CMD_ERRATA |
| #define CONFIG_CMD_IRQ |
| |
| #ifdef CONFIG_PCI |
| #define CONFIG_CMD_PCI |
| #endif |
| |
| /* |
| * USB |
| */ |
| #define CONFIG_HAS_FSL_DR_USB |
| #define CONFIG_HAS_FSL_MPH_USB |
| |
| #if defined(CONFIG_HAS_FSL_DR_USB) || defined(CONFIG_HAS_FSL_MPH_USB) |
| #define CONFIG_USB_EHCI |
| #define CONFIG_USB_EHCI_FSL |
| #define CONFIG_EHCI_HCD_INIT_AFTER_RESET |
| #endif |
| |
| #define CONFIG_MMC |
| |
| #ifdef CONFIG_MMC |
| #define CONFIG_FSL_ESDHC |
| #define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR |
| #define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT |
| #define CONFIG_GENERIC_MMC |
| #define CONFIG_DOS_PARTITION |
| #endif |
| |
| /* Hash command with SHA acceleration supported in hardware */ |
| #ifdef CONFIG_FSL_CAAM |
| #define CONFIG_CMD_HASH |
| #define CONFIG_SHA_HW_ACCEL |
| #endif |
| |
| /* |
| * Miscellaneous configurable options |
| */ |
| #define CONFIG_SYS_LONGHELP /* undef to save memory */ |
| #define CONFIG_CMDLINE_EDITING /* Command-line editing */ |
| #define CONFIG_AUTO_COMPLETE /* add autocompletion support */ |
| #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ |
| #ifdef CONFIG_CMD_KGDB |
| #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ |
| #else |
| #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ |
| #endif |
| /* Print Buffer Size */ |
| #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ |
| sizeof(CONFIG_SYS_PROMPT)+16) |
| #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ |
| /* Boot Argument Buffer Size */ |
| #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE |
| |
| /* |
| * For booting Linux, the board info and command line data |
| * have to be in the first 64 MB of memory, since this is |
| * the maximum mapped by the Linux kernel during initialization. |
| */ |
| #define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory for Linux */ |
| #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ |
| |
| #ifdef CONFIG_CMD_KGDB |
| #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ |
| #endif |
| |
| /* |
| * Environment Configuration |
| */ |
| #define CONFIG_ROOTPATH "/opt/nfsroot" |
| #define CONFIG_BOOTFILE "uImage" |
| #define CONFIG_UBOOTPATH u-boot.bin |
| |
| /* default location for tftp and bootm */ |
| #define CONFIG_LOADADDR 1000000 |
| |
| |
| #define CONFIG_BAUDRATE 115200 |
| |
| #define __USB_PHY_TYPE utmi |
| |
| #define CONFIG_EXTRA_ENV_SETTINGS \ |
| "hwconfig=fsl_ddr:ctlr_intlv=cacheline," \ |
| "bank_intlv=cs0_cs1\0" \ |
| "netdev=eth0\0" \ |
| "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \ |
| "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \ |
| "tftpflash=tftpboot $loadaddr $uboot && " \ |
| "protect off $ubootaddr +$filesize && " \ |
| "erase $ubootaddr +$filesize && " \ |
| "cp.b $loadaddr $ubootaddr $filesize && " \ |
| "protect on $ubootaddr +$filesize && " \ |
| "cmp.b $loadaddr $ubootaddr $filesize\0" \ |
| "consoledev=ttyS0\0" \ |
| "usb_phy_type=" __stringify(__USB_PHY_TYPE) "\0" \ |
| "usb_dr_mode=host\0" \ |
| "ramdiskaddr=2000000\0" \ |
| "ramdiskfile=p2041rdb/ramdisk.uboot\0" \ |
| "fdtaddr=1e00000\0" \ |
| "fdtfile=p2041rdb/p2041rdb.dtb\0" \ |
| "bdev=sda3\0" |
| |
| #define CONFIG_HDBOOT \ |
| "setenv bootargs root=/dev/$bdev rw " \ |
| "console=$consoledev,$baudrate $othbootargs;" \ |
| "tftp $loadaddr $bootfile;" \ |
| "tftp $fdtaddr $fdtfile;" \ |
| "bootm $loadaddr - $fdtaddr" |
| |
| #define CONFIG_NFSBOOTCOMMAND \ |
| "setenv bootargs root=/dev/nfs rw " \ |
| "nfsroot=$serverip:$rootpath " \ |
| "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ |
| "console=$consoledev,$baudrate $othbootargs;" \ |
| "tftp $loadaddr $bootfile;" \ |
| "tftp $fdtaddr $fdtfile;" \ |
| "bootm $loadaddr - $fdtaddr" |
| |
| #define CONFIG_RAMBOOTCOMMAND \ |
| "setenv bootargs root=/dev/ram rw " \ |
| "console=$consoledev,$baudrate $othbootargs;" \ |
| "tftp $ramdiskaddr $ramdiskfile;" \ |
| "tftp $loadaddr $bootfile;" \ |
| "tftp $fdtaddr $fdtfile;" \ |
| "bootm $loadaddr $ramdiskaddr $fdtaddr" |
| |
| #define CONFIG_BOOTCOMMAND CONFIG_HDBOOT |
| |
| #include <asm/fsl_secure_boot.h> |
| |
| #endif /* __CONFIG_H */ |