| // SPDX-License-Identifier: GPL-2.0+ |
| /* |
| * Copyright (C) 2013 Samsung Electronics |
| */ |
| |
| #include <common.h> |
| #include <cpu_func.h> |
| #include <init.h> |
| #include <log.h> |
| #include <usb.h> |
| #include <asm/global_data.h> |
| #include <asm/gpio.h> |
| #include <asm/arch/pinmux.h> |
| #include <asm/arch/dwmmc.h> |
| #include <asm/arch/power.h> |
| |
| DECLARE_GLOBAL_DATA_PTR; |
| |
| #ifdef CONFIG_USB_EHCI_EXYNOS |
| int board_usb_init(int index, enum usb_init_type init) |
| { |
| /* Configure gpios for usb 3503 hub: |
| * disconnect, toggle reset and connect |
| */ |
| gpio_request(EXYNOS5_GPIO_D17, "usb_connect"); |
| gpio_request(EXYNOS5_GPIO_X35, "usb_reset"); |
| gpio_direction_output(EXYNOS5_GPIO_D17, 0); |
| gpio_direction_output(EXYNOS5_GPIO_X35, 0); |
| |
| gpio_direction_output(EXYNOS5_GPIO_X35, 1); |
| gpio_direction_output(EXYNOS5_GPIO_D17, 1); |
| |
| return 0; |
| } |
| #endif |
| |
| int board_init(void) |
| { |
| gd->bd->bi_boot_params = (PHYS_SDRAM_1 + 0x100UL); |
| return 0; |
| } |
| |
| int dram_init(void) |
| { |
| int i; |
| u32 addr; |
| |
| for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) { |
| addr = CFG_SYS_SDRAM_BASE + (i * SDRAM_BANK_SIZE); |
| gd->ram_size += get_ram_size((long *)addr, SDRAM_BANK_SIZE); |
| } |
| return 0; |
| } |
| |
| int power_init_board(void) |
| { |
| set_ps_hold_ctrl(); |
| return 0; |
| } |
| |
| int dram_init_banksize(void) |
| { |
| int i; |
| u32 addr, size; |
| |
| for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) { |
| addr = CFG_SYS_SDRAM_BASE + (i * SDRAM_BANK_SIZE); |
| size = get_ram_size((long *)addr, SDRAM_BANK_SIZE); |
| |
| gd->bd->bi_dram[i].start = addr; |
| gd->bd->bi_dram[i].size = size; |
| } |
| |
| return 0; |
| } |
| |
| static int board_uart_init(void) |
| { |
| int err = 0, uart_id; |
| |
| for (uart_id = PERIPH_ID_UART0; uart_id <= PERIPH_ID_UART3; uart_id++) { |
| err = exynos_pinmux_config(uart_id, PINMUX_FLAG_NONE); |
| if (err) { |
| debug("UART%d not configured\n", |
| (uart_id - PERIPH_ID_UART0)); |
| return err; |
| } |
| } |
| return err; |
| } |
| |
| #ifdef CONFIG_BOARD_EARLY_INIT_F |
| int board_early_init_f(void) |
| { |
| int err; |
| |
| err = board_uart_init(); |
| if (err) { |
| debug("UART init failed\n"); |
| return err; |
| } |
| return err; |
| } |
| #endif |
| |
| #ifdef CONFIG_DISPLAY_BOARDINFO |
| int checkboard(void) |
| { |
| printf("\nBoard: Arndale\n"); |
| |
| return 0; |
| } |
| #endif |
| |
| #ifdef CONFIG_SMP_PEN_ADDR |
| void smp_set_core_boot_addr(unsigned long addr, int corenr) |
| { |
| writel(addr, CONFIG_SMP_PEN_ADDR); |
| |
| /* make sure this write is really executed */ |
| __asm__ volatile ("dsb\n"); |
| } |
| #endif |