include/configs/ls2080ardb.h - filogic/uboot - Gitiles

 /* SPDX-License-Identifier: GPL-2.0+ */
 /*
  * Copyright 2017, 2019-2021 NXP
  * Copyright 2015 Freescale Semiconductor
  */

 #ifndef __LS2_RDB_H
 #define __LS2_RDB_H

 #include "ls2080a_common.h"

 #define I2C_MUX_CH_VOL_MONITOR		0xa
 #define I2C_VOL_MONITOR_ADDR		0x38

 /* step the IR regulator in 5mV increments */
 #define IR_VDD_STEP_DOWN		5
 #define IR_VDD_STEP_UP			5
 /* The lowest and highest voltage allowed for LS2080ARDB */
 #define VDD_MV_MIN			819
 #define VDD_MV_MAX			1212

 #define COUNTER_FREQUENCY_REAL		(get_board_sys_clk()/4)

 #define CONFIG_MEM_INIT_VALUE		0xdeadbeef
 #define SPD_EEPROM_ADDRESS1	0x51
 #define SPD_EEPROM_ADDRESS2	0x52
 #define SPD_EEPROM_ADDRESS3	0x53
 #define SPD_EEPROM_ADDRESS4	0x54
 #define SPD_EEPROM_ADDRESS5	0x55
 #define SPD_EEPROM_ADDRESS6	0x56	/* dummy address */
 #define SPD_EEPROM_ADDRESS	SPD_EEPROM_ADDRESS1

 #if !defined(CONFIG_FSL_QSPI) || defined(CONFIG_TFABOOT)

 #define CONFIG_SYS_NOR0_CSPR_EXT	(0x0)
 #define CONFIG_SYS_NOR_AMASK		IFC_AMASK(128*1024*1024)
 #define CONFIG_SYS_NOR_AMASK_EARLY	IFC_AMASK(64*1024*1024)

 #define CONFIG_SYS_NOR0_CSPR					\
 	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS)		| \
 	CSPR_PORT_SIZE_16					| \
 	CSPR_MSEL_NOR						| \
 	CSPR_V)
 #define CONFIG_SYS_NOR0_CSPR_EARLY				\
 	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS_EARLY)	| \
 	CSPR_PORT_SIZE_16					| \
 	CSPR_MSEL_NOR						| \
 	CSPR_V)
 #define CONFIG_SYS_NOR_CSOR	CSOR_NOR_ADM_SHIFT(12)
 #define CONFIG_SYS_NOR_FTIM0	(FTIM0_NOR_TACSE(0x4) | \
 				FTIM0_NOR_TEADC(0x5) | \
 				FTIM0_NOR_TEAHC(0x5))
 #define CONFIG_SYS_NOR_FTIM1	(FTIM1_NOR_TACO(0x35) | \
 				FTIM1_NOR_TRAD_NOR(0x1a) |\
 				FTIM1_NOR_TSEQRAD_NOR(0x13))
 #define CONFIG_SYS_NOR_FTIM2	(FTIM2_NOR_TCS(0x4) | \
 				FTIM2_NOR_TCH(0x4) | \
 				FTIM2_NOR_TWPH(0x0E) | \
 				FTIM2_NOR_TWP(0x1c))
 #define CONFIG_SYS_NOR_FTIM3	0x04000000
 #define CONFIG_SYS_IFC_CCR	0x01000000

 #ifdef CONFIG_MTD_NOR_FLASH
 #define CONFIG_FLASH_SHOW_PROGRESS	45 /* count down from 45/5: 9..1 */

 #define CONFIG_SYS_FLASH_BANKS_LIST	{ CONFIG_SYS_FLASH_BASE,\
 					 CONFIG_SYS_FLASH_BASE + 0x40000000}
 #endif

 #define CFG_SYS_NAND_CSPR_EXT	(0x0)
 #define CFG_SYS_NAND_CSPR	(CSPR_PHYS_ADDR(CFG_SYS_NAND_BASE_PHYS) \
 				| CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
 				| CSPR_MSEL_NAND	/* MSEL = NAND */ \
 				| CSPR_V)
 #define CFG_SYS_NAND_AMASK	IFC_AMASK(64 * 1024)

 #define CFG_SYS_NAND_CSOR    (CSOR_NAND_ECC_ENC_EN   /* ECC on encode */ \
 				| CSOR_NAND_ECC_DEC_EN  /* ECC on decode */ \
 				| CSOR_NAND_ECC_MODE_4  /* 4-bit ECC */ \
 				| CSOR_NAND_RAL_3	/* RAL = 3Byes */ \
 				| CSOR_NAND_PGS_4K	/* Page Size = 4K */ \
 				| CSOR_NAND_SPRZ_224	/* Spare size = 224 */ \
 				| CSOR_NAND_PB(128))	/* Pages Per Block 128*/

 /* ONFI NAND Flash mode0 Timing Params */
 #define CFG_SYS_NAND_FTIM0		(FTIM0_NAND_TCCST(0x0e) | \
 					FTIM0_NAND_TWP(0x30)   | \
 					FTIM0_NAND_TWCHT(0x0e) | \
 					FTIM0_NAND_TWH(0x14))
 #define CFG_SYS_NAND_FTIM1		(FTIM1_NAND_TADLE(0x64) | \
 					FTIM1_NAND_TWBE(0xab)  | \
 					FTIM1_NAND_TRR(0x1c)   | \
 					FTIM1_NAND_TRP(0x30))
 #define CFG_SYS_NAND_FTIM2		(FTIM2_NAND_TRAD(0x1e) | \
 					FTIM2_NAND_TREH(0x14) | \
 					FTIM2_NAND_TWHRE(0x3c))
 #define CFG_SYS_NAND_FTIM3		0x0

 #define CFG_SYS_NAND_BASE_LIST	{ CFG_SYS_NAND_BASE }
 #define CONFIG_MTD_NAND_VERIFY_WRITE

 #define QIXIS_LBMAP_SWITCH		0x06
 #define QIXIS_LBMAP_MASK		0x0f
 #define QIXIS_LBMAP_SHIFT		0
 #define QIXIS_LBMAP_DFLTBANK		0x00
 #define QIXIS_LBMAP_ALTBANK		0x04
 #define QIXIS_LBMAP_NAND		0x09
 #define QIXIS_RST_CTL_RESET		0x31
 #define QIXIS_RST_CTL_RESET_EN		0x30
 #define QIXIS_RCFG_CTL_RECONFIG_IDLE	0x20
 #define QIXIS_RCFG_CTL_RECONFIG_START	0x21
 #define QIXIS_RCFG_CTL_WATCHDOG_ENBLE	0x08
 #define QIXIS_RCW_SRC_NAND		0x119
 #define	QIXIS_RST_FORCE_MEM		0x01

 #define CONFIG_SYS_CSPR3_EXT	(0x0)
 #define CONFIG_SYS_CSPR3	(CSPR_PHYS_ADDR(QIXIS_BASE_PHYS_EARLY) \
 				| CSPR_PORT_SIZE_8 \
 				| CSPR_MSEL_GPCM \
 				| CSPR_V)
 #define CONFIG_SYS_CSPR3_FINAL	(CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) \
 				| CSPR_PORT_SIZE_8 \
 				| CSPR_MSEL_GPCM \
 				| CSPR_V)

 #define CONFIG_SYS_AMASK3	IFC_AMASK(64*1024)
 #define CONFIG_SYS_CSOR3	CSOR_GPCM_ADM_SHIFT(12)
 /* QIXIS Timing parameters for IFC CS3 */
 #define CONFIG_SYS_CS3_FTIM0		(FTIM0_GPCM_TACSE(0x0e) | \
 					FTIM0_GPCM_TEADC(0x0e) | \
 					FTIM0_GPCM_TEAHC(0x0e))
 #define CONFIG_SYS_CS3_FTIM1		(FTIM1_GPCM_TACO(0xff) | \
 					FTIM1_GPCM_TRAD(0x3f))
 #define CONFIG_SYS_CS3_FTIM2		(FTIM2_GPCM_TCS(0xf) | \
 					FTIM2_GPCM_TCH(0xf) | \
 					FTIM2_GPCM_TWP(0x3E))
 #define CONFIG_SYS_CS3_FTIM3		0x0

 #if defined(CONFIG_SPL) && defined(CONFIG_MTD_RAW_NAND)
 #define CONFIG_SYS_CSPR2_EXT		CONFIG_SYS_NOR0_CSPR_EXT
 #define CONFIG_SYS_CSPR2		CONFIG_SYS_NOR0_CSPR_EARLY
 #define CONFIG_SYS_CSPR2_FINAL		CONFIG_SYS_NOR0_CSPR
 #define CONFIG_SYS_AMASK2		CONFIG_SYS_NOR_AMASK
 #define CONFIG_SYS_CSOR2		CONFIG_SYS_NOR_CSOR
 #define CONFIG_SYS_CS2_FTIM0		CONFIG_SYS_NOR_FTIM0
 #define CONFIG_SYS_CS2_FTIM1		CONFIG_SYS_NOR_FTIM1
 #define CONFIG_SYS_CS2_FTIM2		CONFIG_SYS_NOR_FTIM2
 #define CONFIG_SYS_CS2_FTIM3		CONFIG_SYS_NOR_FTIM3
 #define CONFIG_SYS_CSPR0_EXT		CFG_SYS_NAND_CSPR_EXT
 #define CONFIG_SYS_CSPR0		CFG_SYS_NAND_CSPR
 #define CONFIG_SYS_AMASK0		CFG_SYS_NAND_AMASK
 #define CONFIG_SYS_CSOR0		CFG_SYS_NAND_CSOR
 #define CONFIG_SYS_CS0_FTIM0		CFG_SYS_NAND_FTIM0
 #define CONFIG_SYS_CS0_FTIM1		CFG_SYS_NAND_FTIM1
 #define CONFIG_SYS_CS0_FTIM2		CFG_SYS_NAND_FTIM2
 #define CONFIG_SYS_CS0_FTIM3		CFG_SYS_NAND_FTIM3

 #define CFG_SYS_NAND_U_BOOT_SIZE	(512 * 1024)
 #else
 #define CONFIG_SYS_CSPR0_EXT		CONFIG_SYS_NOR0_CSPR_EXT
 #define CONFIG_SYS_CSPR0		CONFIG_SYS_NOR0_CSPR_EARLY
 #define CONFIG_SYS_CSPR0_FINAL		CONFIG_SYS_NOR0_CSPR
 #define CONFIG_SYS_AMASK0		CONFIG_SYS_NOR_AMASK
 #define CONFIG_SYS_CSOR0		CONFIG_SYS_NOR_CSOR
 #define CONFIG_SYS_CS0_FTIM0		CONFIG_SYS_NOR_FTIM0
 #define CONFIG_SYS_CS0_FTIM1		CONFIG_SYS_NOR_FTIM1
 #define CONFIG_SYS_CS0_FTIM2		CONFIG_SYS_NOR_FTIM2
 #define CONFIG_SYS_CS0_FTIM3		CONFIG_SYS_NOR_FTIM3
 #define CONFIG_SYS_CSPR2_EXT		CFG_SYS_NAND_CSPR_EXT
 #define CONFIG_SYS_CSPR2		CFG_SYS_NAND_CSPR
 #define CONFIG_SYS_AMASK2		CFG_SYS_NAND_AMASK
 #define CONFIG_SYS_CSOR2		CFG_SYS_NAND_CSOR
 #define CONFIG_SYS_CS2_FTIM0		CFG_SYS_NAND_FTIM0
 #define CONFIG_SYS_CS2_FTIM1		CFG_SYS_NAND_FTIM1
 #define CONFIG_SYS_CS2_FTIM2		CFG_SYS_NAND_FTIM2
 #define CONFIG_SYS_CS2_FTIM3		CFG_SYS_NAND_FTIM3
 #endif
 #endif
 #define CONFIG_SYS_LS_MC_BOOT_TIMEOUT_MS 5000

 #ifdef CONFIG_TARGET_LS2081ARDB
 #define QIXIS_QMAP_MASK			0x07
 #define QIXIS_QMAP_SHIFT		5
 #define QIXIS_LBMAP_DFLTBANK		0x00
 #define QIXIS_LBMAP_QSPI		0x00
 #define QIXIS_RCW_SRC_QSPI		0x62
 #define QIXIS_LBMAP_ALTBANK		0x20
 #define QIXIS_RST_CTL_RESET		0x31
 #define QIXIS_RCFG_CTL_RECONFIG_IDLE	0x20
 #define QIXIS_RCFG_CTL_RECONFIG_START	0x21
 #define QIXIS_RCFG_CTL_WATCHDOG_ENBLE	0x08
 #define QIXIS_LBMAP_MASK		0x0f
 #define QIXIS_RST_CTL_RESET_EN		0x30
 #endif

 /*
  * I2C
  */
 #ifdef CONFIG_TARGET_LS2081ARDB
 #define CONFIG_SYS_I2C_FPGA_ADDR	0x66
 #endif
 #define I2C_MUX_PCA_ADDR		0x75
 #define I2C_MUX_PCA_ADDR_PRI		0x75 /* Primary Mux*/

 /* I2C bus multiplexer */
 #define I2C_MUX_CH_DEFAULT      0x8

 /* SPI */

 /*
  * RTC configuration
  */
 #define RTC
 #ifdef CONFIG_TARGET_LS2081ARDB
 #define CONFIG_SYS_I2C_RTC_ADDR         0x51
 #else
 #define CONFIG_RTC_DS3231               1
 #define CONFIG_SYS_I2C_RTC_ADDR         0x68
 #endif

 #define BOOT_TARGET_DEVICES(func) \
 	func(USB, usb, 0) \
 	func(MMC, mmc, 0) \
 	func(SCSI, scsi, 0) \
 	func(DHCP, dhcp, na)
 #include <config_distro_bootcmd.h>

 #ifdef CONFIG_TFABOOT
 #define QSPI_MC_INIT_CMD				\
 	"sf probe 0:0; "				\
 	"sf read 0x80640000 0x640000 0x80000; "		\
 	"env exists secureboot && "			\
 	"esbc_validate 0x80640000 && "			\
 	"esbc_validate 0x80680000; "			\
 	"sf read 0x80a00000 0xa00000 0x200000; "	\
 	"sf read 0x80e00000 0xe00000 0x100000; "	\
 	"fsl_mc start mc 0x80a00000 0x80e00000 \0"
 #define SD_MC_INIT_CMD				\
 	"mmcinfo;mmc read 0x80a00000 0x5000 0x1000;" \
 	"mmc read 0x80e00000 0x7000 0x800;"	\
 	"env exists secureboot && "		\
 	"mmc read 0x80640000 0x3200 0x20 && "	\
 	"mmc read 0x80680000 0x3400 0x20 && "	\
 	"esbc_validate 0x80640000 && "		\
 	"esbc_validate 0x80680000 ;"		\
 	"fsl_mc start mc 0x80a00000 0x80e00000\0"
 #define IFC_MC_INIT_CMD				\
 	"env exists secureboot && "	\
 	"esbc_validate 0x580640000 && "		\
 	"esbc_validate 0x580680000; "		\
 	"fsl_mc start mc 0x580a00000 0x580e00000 \0"
 #else
 #ifdef CONFIG_QSPI_BOOT
 #define MC_INIT_CMD					\
 	"mcinitcmd=sf probe 0:0; "			\
 	"sf read 0x80640000 0x640000 0x80000; "		\
 	"env exists secureboot && "			\
 	"esbc_validate 0x80640000 && "			\
 	"esbc_validate 0x80680000; "			\
 	"sf read 0x80a00000 0xa00000 0x200000; "	\
 	"sf read 0x80e00000 0xe00000 0x100000; "	\
 	"fsl_mc start mc 0x80a00000 0x80e00000 \0"
 #elif defined(CONFIG_SD_BOOT)
 #define MC_INIT_CMD                             \
 	"mcinitcmd=mmcinfo;mmc read 0x80a00000 0x5000 0x1000;" \
 	"mmc read 0x80e00000 0x7000 0x800;"	\
 	"env exists secureboot && "		\
 	"mmc read 0x80640000 0x3200 0x20 && "	\
 	"mmc read 0x80680000 0x3400 0x20 && "	\
 	"esbc_validate 0x80640000 && "		\
 	"esbc_validate 0x80680000 ;"		\
 	"fsl_mc start mc 0x80a00000 0x80e00000\0" \
 	"mcmemsize=0x70000000\0"
 #else
 #define MC_INIT_CMD				\
 	"mcinitcmd=env exists secureboot && "	\
 	"esbc_validate 0x580640000 && "		\
 	"esbc_validate 0x580680000; "		\
 	"fsl_mc start mc 0x580a00000 0x580e00000 \0"
 #endif
 #endif

 /* Initial environment variables */
 #undef CONFIG_EXTRA_ENV_SETTINGS
 #ifdef CONFIG_TFABOOT
 #define CONFIG_EXTRA_ENV_SETTINGS		\
 	"hwconfig=fsl_ddr:bank_intlv=auto\0"	\
 	"ramdisk_addr=0x800000\0"		\
 	"ramdisk_size=0x2000000\0"		\
 	"fdt_high=0xa0000000\0"			\
 	"initrd_high=0xffffffffffffffff\0"	\
 	"kernel_addr=0x581000000\0"		\
 	"kernel_start=0x1000000\0"		\
 	"kernelheader_start=0x800000\0"		\
 	"scriptaddr=0x80000000\0"		\
 	"scripthdraddr=0x80080000\0"		\
 	"fdtheader_addr_r=0x80100000\0"		\
 	"kernelheader_addr_r=0x80200000\0"	\
 	"kernelheader_addr=0x580600000\0"	\
 	"kernel_addr_r=0x81000000\0"		\
 	"kernelheader_size=0x40000\0"		\
 	"fdt_addr_r=0x90000000\0"		\
 	"load_addr=0xa0000000\0"		\
 	"kernel_size=0x2800000\0"		\
 	"kernel_addr_sd=0x8000\0"		\
 	"kernel_size_sd=0x14000\0"              \
 	"console=ttyAMA0,38400n8\0"		\
 	"mcmemsize=0x70000000\0"		\
 	"sd_bootcmd=echo Trying load from SD ..;" \
 	"mmcinfo; mmc read $load_addr "		\
 	"$kernel_addr_sd $kernel_size_sd && "	\
 	"bootm $load_addr#$board\0"             \
 	QSPI_MC_INIT_CMD				\
 	BOOTENV					\
 	"boot_scripts=ls2088ardb_boot.scr\0"	\
 	"boot_script_hdr=hdr_ls2088ardb_bs.out\0"	\
 	"scan_dev_for_boot_part="		\
 		"part list ${devtype} ${devnum} devplist; "	\
 		"env exists devplist || setenv devplist 1; "	\
 		"for distro_bootpart in ${devplist}; do "	\
 			"if fstype ${devtype} "			\
 				"${devnum}:${distro_bootpart} "	\
 				"bootfstype; then "		\
 				"run scan_dev_for_boot; "	\
 			"fi; "					\
 		"done\0"					\
 	"boot_a_script="					\
 		"load ${devtype} ${devnum}:${distro_bootpart} "	\
 			"${scriptaddr} ${prefix}${script}; "	\
 		"env exists secureboot && load ${devtype} "	\
 			"${devnum}:${distro_bootpart} "		\
 			"${scripthdraddr} ${prefix}${boot_script_hdr} "	\
 			"&& esbc_validate ${scripthdraddr};"	\
 		"source ${scriptaddr}\0"			\
 	"qspi_bootcmd=echo Trying load from qspi..;"		\
 		"sf probe && sf read $load_addr "		\
 		"$kernel_start $kernel_size ; env exists secureboot &&"	\
 		"sf read $kernelheader_addr_r $kernelheader_start "	\
 		"$kernelheader_size && esbc_validate ${kernelheader_addr_r}; "\
 		" bootm $load_addr#$board\0"			\
 	"nor_bootcmd=echo Trying load from nor..;"		\
 		"cp.b $kernel_addr $load_addr "			\
 		"$kernel_size ; env exists secureboot && "	\
 		"cp.b $kernelheader_addr $kernelheader_addr_r "	\
 		"$kernelheader_size && esbc_validate ${kernelheader_addr_r}; "\
 		"bootm $load_addr#$board\0"
 #else
 #define CONFIG_EXTRA_ENV_SETTINGS		\
 	"hwconfig=fsl_ddr:bank_intlv=auto\0"	\
 	"ramdisk_addr=0x800000\0"		\
 	"ramdisk_size=0x2000000\0"		\
 	"fdt_high=0xa0000000\0"			\
 	"initrd_high=0xffffffffffffffff\0"	\
 	"kernel_addr=0x581000000\0"		\
 	"kernel_start=0x1000000\0"		\
 	"kernelheader_start=0x600000\0"		\
 	"scriptaddr=0x80000000\0"		\
 	"scripthdraddr=0x80080000\0"		\
 	"fdtheader_addr_r=0x80100000\0"		\
 	"kernelheader_addr_r=0x80200000\0"	\
 	"kernelheader_addr=0x580600000\0"	\
 	"kernel_addr_r=0x81000000\0"		\
 	"kernelheader_size=0x40000\0"		\
 	"fdt_addr_r=0x90000000\0"		\
 	"load_addr=0xa0000000\0"		\
 	"kernel_size=0x2800000\0"		\
 	"kernel_addr_sd=0x8000\0"		\
 	"kernel_size_sd=0x14000\0"              \
 	"console=ttyAMA0,38400n8\0"		\
 	"mcmemsize=0x70000000\0"		\
 	"sd_bootcmd=echo Trying load from SD ..;" \
 	"mmcinfo; mmc read $load_addr "		\
 	"$kernel_addr_sd $kernel_size_sd && "	\
 	"bootm $load_addr#$board\0"             \
 	MC_INIT_CMD				\
 	BOOTENV					\
 	"boot_scripts=ls2088ardb_boot.scr\0"	\
 	"boot_script_hdr=hdr_ls2088ardb_bs.out\0"	\
 	"scan_dev_for_boot_part="		\
 		"part list ${devtype} ${devnum} devplist; "	\
 		"env exists devplist || setenv devplist 1; "	\
 		"for distro_bootpart in ${devplist}; do "	\
 			"if fstype ${devtype} "			\
 				"${devnum}:${distro_bootpart} "	\
 				"bootfstype; then "		\
 				"run scan_dev_for_boot; "	\
 			"fi; "					\
 		"done\0"					\
 	"boot_a_script="					\
 		"load ${devtype} ${devnum}:${distro_bootpart} "	\
 			"${scriptaddr} ${prefix}${script}; "	\
 		"env exists secureboot && load ${devtype} "	\
 			"${devnum}:${distro_bootpart} "		\
 			"${scripthdraddr} ${prefix}${boot_script_hdr}; " \
 			"env exists secureboot "	\
 			"&& esbc_validate ${scripthdraddr};"	\
 		"source ${scriptaddr}\0"			\
 	"qspi_bootcmd=echo Trying load from qspi..;"		\
 		"sf probe && sf read $load_addr "		\
 		"$kernel_start $kernel_size ; env exists secureboot &&"	\
 		"sf read $kernelheader_addr_r $kernelheader_start "	\
 		"$kernelheader_size && esbc_validate ${kernelheader_addr_r}; "\
 		" bootm $load_addr#$board\0"			\
 	"nor_bootcmd=echo Trying load from nor..;"		\
 		"cp.b $kernel_addr $load_addr "			\
 		"$kernel_size ; env exists secureboot && "	\
 		"cp.b $kernelheader_addr $kernelheader_addr_r "	\
 		"$kernelheader_size && esbc_validate ${kernelheader_addr_r}; "\
 		"bootm $load_addr#$board\0"
 #endif

 #ifdef CONFIG_TFABOOT
 #define QSPI_NOR_BOOTCOMMAND						\
 			"sf probe 0:0; "				\
 			"sf read 0x806c0000 0x6c0000 0x40000; "		\
 			"env exists mcinitcmd && env exists secureboot "\
 			"&& esbc_validate 0x806c0000; "			\
 			"sf read 0x80d00000 0xd00000 0x100000; "	\
 			"env exists mcinitcmd && "			\
 			"fsl_mc lazyapply dpl 0x80d00000; "		\
 			"run distro_bootcmd;run qspi_bootcmd; "		\
 			"env exists secureboot && esbc_halt;"

 /* Try to boot an on-SD kernel first, then do normal distro boot */
 #define SD_BOOTCOMMAND						\
 			"env exists mcinitcmd && env exists secureboot "\
 			"&& mmcinfo && mmc read $load_addr 0x3600 0x800 " \
 			"&& esbc_validate $load_addr; "			\
 			"env exists mcinitcmd && run mcinitcmd "	\
 			"&& mmc read 0x80d00000 0x6800 0x800 "		\
 			"&& fsl_mc lazyapply dpl 0x80d00000; "		\
 			"run distro_bootcmd;run sd_bootcmd; "		\
 			"env exists secureboot && esbc_halt;"

 /* Try to boot an on-NOR kernel first, then do normal distro boot */
 #define IFC_NOR_BOOTCOMMAND						\
 			"env exists mcinitcmd && env exists secureboot "\
 			"&& esbc_validate 0x5806C0000; env exists mcinitcmd "\
 			"&& fsl_mc lazyapply dpl 0x580d00000;"		\
 			"run distro_bootcmd;run nor_bootcmd; "		\
 			"env exists secureboot && esbc_halt;"
 #else
 #ifdef CONFIG_QSPI_BOOT
 /* Try to boot an on-QSPI kernel first, then do normal distro boot */
 #elif defined(CONFIG_SD_BOOT)
 /* Try to boot an on-SD kernel first, then do normal distro boot */
 #else
 /* Try to boot an on-NOR kernel first, then do normal distro boot */
 #endif
 #endif

 /* MAC/PHY configuration */
 #define CORTINA_PHY_ADDR1	0x10
 #define CORTINA_PHY_ADDR2	0x11
 #define CORTINA_PHY_ADDR3	0x12
 #define CORTINA_PHY_ADDR4	0x13
 #define AQ_PHY_ADDR1		0x00
 #define AQ_PHY_ADDR2		0x01
 #define AQ_PHY_ADDR3		0x02
 #define AQ_PHY_ADDR4		0x03
 #define AQR405_IRQ_MASK		0x36

 #include <asm/fsl_secure_boot.h>

 #endif /* __LS2_RDB_H */
	/* SPDX-License-Identifier: GPL-2.0+ */
	/*
	* Copyright 2017, 2019-2021 NXP
	* Copyright 2015 Freescale Semiconductor
	*/

	#ifndef __LS2_RDB_H
	#define __LS2_RDB_H

	#include "ls2080a_common.h"

	#define I2C_MUX_CH_VOL_MONITOR 0xa
	#define I2C_VOL_MONITOR_ADDR 0x38

	/* step the IR regulator in 5mV increments */
	#define IR_VDD_STEP_DOWN 5
	#define IR_VDD_STEP_UP 5
	/* The lowest and highest voltage allowed for LS2080ARDB */
	#define VDD_MV_MIN 819
	#define VDD_MV_MAX 1212

	#define COUNTER_FREQUENCY_REAL (get_board_sys_clk()/4)

	#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
	#define SPD_EEPROM_ADDRESS1 0x51
	#define SPD_EEPROM_ADDRESS2 0x52
	#define SPD_EEPROM_ADDRESS3 0x53
	#define SPD_EEPROM_ADDRESS4 0x54
	#define SPD_EEPROM_ADDRESS5 0x55
	#define SPD_EEPROM_ADDRESS6 0x56 /* dummy address */
	#define SPD_EEPROM_ADDRESS SPD_EEPROM_ADDRESS1

	#if !defined(CONFIG_FSL_QSPI) \|\| defined(CONFIG_TFABOOT)

	#define CONFIG_SYS_NOR0_CSPR_EXT (0x0)
	#define CONFIG_SYS_NOR_AMASK IFC_AMASK(12810241024)
	#define CONFIG_SYS_NOR_AMASK_EARLY IFC_AMASK(6410241024)

	#define CONFIG_SYS_NOR0_CSPR \
	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) \| \
	CSPR_PORT_SIZE_16 \| \
	CSPR_MSEL_NOR \| \
	CSPR_V)
	#define CONFIG_SYS_NOR0_CSPR_EARLY \
	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS_EARLY) \| \
	CSPR_PORT_SIZE_16 \| \
	CSPR_MSEL_NOR \| \
	CSPR_V)
	#define CONFIG_SYS_NOR_CSOR CSOR_NOR_ADM_SHIFT(12)
	#define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) \| \
	FTIM0_NOR_TEADC(0x5) \| \
	FTIM0_NOR_TEAHC(0x5))
	#define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) \| \
	FTIM1_NOR_TRAD_NOR(0x1a) \|\
	FTIM1_NOR_TSEQRAD_NOR(0x13))
	#define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) \| \
	FTIM2_NOR_TCH(0x4) \| \
	FTIM2_NOR_TWPH(0x0E) \| \
	FTIM2_NOR_TWP(0x1c))
	#define CONFIG_SYS_NOR_FTIM3 0x04000000
	#define CONFIG_SYS_IFC_CCR 0x01000000

	#ifdef CONFIG_MTD_NOR_FLASH
	#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */

	#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE,\
	CONFIG_SYS_FLASH_BASE + 0x40000000}
	#endif

	#define CFG_SYS_NAND_CSPR_EXT (0x0)
	#define CFG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CFG_SYS_NAND_BASE_PHYS) \
	\| CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
	\| CSPR_MSEL_NAND /* MSEL = NAND */ \
	\| CSPR_V)
	#define CFG_SYS_NAND_AMASK IFC_AMASK(64 * 1024)

	#define CFG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \
	\| CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \
	\| CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \
	\| CSOR_NAND_RAL_3 /* RAL = 3Byes */ \
	\| CSOR_NAND_PGS_4K /* Page Size = 4K */ \
	\| CSOR_NAND_SPRZ_224 /* Spare size = 224 */ \
	\| CSOR_NAND_PB(128)) /* Pages Per Block 128*/

	/* ONFI NAND Flash mode0 Timing Params */
	#define CFG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x0e) \| \
	FTIM0_NAND_TWP(0x30) \| \
	FTIM0_NAND_TWCHT(0x0e) \| \
	FTIM0_NAND_TWH(0x14))
	#define CFG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x64) \| \
	FTIM1_NAND_TWBE(0xab) \| \
	FTIM1_NAND_TRR(0x1c) \| \
	FTIM1_NAND_TRP(0x30))
	#define CFG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x1e) \| \
	FTIM2_NAND_TREH(0x14) \| \
	FTIM2_NAND_TWHRE(0x3c))
	#define CFG_SYS_NAND_FTIM3 0x0

	#define CFG_SYS_NAND_BASE_LIST { CFG_SYS_NAND_BASE }
	#define CONFIG_MTD_NAND_VERIFY_WRITE

	#define QIXIS_LBMAP_SWITCH 0x06
	#define QIXIS_LBMAP_MASK 0x0f
	#define QIXIS_LBMAP_SHIFT 0
	#define QIXIS_LBMAP_DFLTBANK 0x00
	#define QIXIS_LBMAP_ALTBANK 0x04
	#define QIXIS_LBMAP_NAND 0x09
	#define QIXIS_RST_CTL_RESET 0x31
	#define QIXIS_RST_CTL_RESET_EN 0x30
	#define QIXIS_RCFG_CTL_RECONFIG_IDLE 0x20
	#define QIXIS_RCFG_CTL_RECONFIG_START 0x21
	#define QIXIS_RCFG_CTL_WATCHDOG_ENBLE 0x08
	#define QIXIS_RCW_SRC_NAND 0x119
	#define QIXIS_RST_FORCE_MEM 0x01

	#define CONFIG_SYS_CSPR3_EXT (0x0)
	#define CONFIG_SYS_CSPR3 (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS_EARLY) \
	\| CSPR_PORT_SIZE_8 \
	\| CSPR_MSEL_GPCM \
	\| CSPR_V)
	#define CONFIG_SYS_CSPR3_FINAL (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) \
	\| CSPR_PORT_SIZE_8 \
	\| CSPR_MSEL_GPCM \
	\| CSPR_V)

	#define CONFIG_SYS_AMASK3 IFC_AMASK(64*1024)
	#define CONFIG_SYS_CSOR3 CSOR_GPCM_ADM_SHIFT(12)
	/* QIXIS Timing parameters for IFC CS3 */
	#define CONFIG_SYS_CS3_FTIM0 (FTIM0_GPCM_TACSE(0x0e) \| \
	FTIM0_GPCM_TEADC(0x0e) \| \
	FTIM0_GPCM_TEAHC(0x0e))
	#define CONFIG_SYS_CS3_FTIM1 (FTIM1_GPCM_TACO(0xff) \| \
	FTIM1_GPCM_TRAD(0x3f))
	#define CONFIG_SYS_CS3_FTIM2 (FTIM2_GPCM_TCS(0xf) \| \
	FTIM2_GPCM_TCH(0xf) \| \
	FTIM2_GPCM_TWP(0x3E))
	#define CONFIG_SYS_CS3_FTIM3 0x0

	#if defined(CONFIG_SPL) && defined(CONFIG_MTD_RAW_NAND)
	#define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NOR0_CSPR_EXT
	#define CONFIG_SYS_CSPR2 CONFIG_SYS_NOR0_CSPR_EARLY
	#define CONFIG_SYS_CSPR2_FINAL CONFIG_SYS_NOR0_CSPR
	#define CONFIG_SYS_AMASK2 CONFIG_SYS_NOR_AMASK
	#define CONFIG_SYS_CSOR2 CONFIG_SYS_NOR_CSOR
	#define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NOR_FTIM0
	#define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NOR_FTIM1
	#define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NOR_FTIM2
	#define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NOR_FTIM3
	#define CONFIG_SYS_CSPR0_EXT CFG_SYS_NAND_CSPR_EXT
	#define CONFIG_SYS_CSPR0 CFG_SYS_NAND_CSPR
	#define CONFIG_SYS_AMASK0 CFG_SYS_NAND_AMASK
	#define CONFIG_SYS_CSOR0 CFG_SYS_NAND_CSOR
	#define CONFIG_SYS_CS0_FTIM0 CFG_SYS_NAND_FTIM0
	#define CONFIG_SYS_CS0_FTIM1 CFG_SYS_NAND_FTIM1
	#define CONFIG_SYS_CS0_FTIM2 CFG_SYS_NAND_FTIM2
	#define CONFIG_SYS_CS0_FTIM3 CFG_SYS_NAND_FTIM3

	#define CFG_SYS_NAND_U_BOOT_SIZE (512 * 1024)
	#else
	#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT
	#define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR_EARLY
	#define CONFIG_SYS_CSPR0_FINAL CONFIG_SYS_NOR0_CSPR
	#define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK
	#define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR
	#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0
	#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1
	#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2
	#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3
	#define CONFIG_SYS_CSPR2_EXT CFG_SYS_NAND_CSPR_EXT
	#define CONFIG_SYS_CSPR2 CFG_SYS_NAND_CSPR
	#define CONFIG_SYS_AMASK2 CFG_SYS_NAND_AMASK
	#define CONFIG_SYS_CSOR2 CFG_SYS_NAND_CSOR
	#define CONFIG_SYS_CS2_FTIM0 CFG_SYS_NAND_FTIM0
	#define CONFIG_SYS_CS2_FTIM1 CFG_SYS_NAND_FTIM1
	#define CONFIG_SYS_CS2_FTIM2 CFG_SYS_NAND_FTIM2
	#define CONFIG_SYS_CS2_FTIM3 CFG_SYS_NAND_FTIM3
	#endif
	#endif
	#define CONFIG_SYS_LS_MC_BOOT_TIMEOUT_MS 5000

	#ifdef CONFIG_TARGET_LS2081ARDB
	#define QIXIS_QMAP_MASK 0x07
	#define QIXIS_QMAP_SHIFT 5
	#define QIXIS_LBMAP_DFLTBANK 0x00
	#define QIXIS_LBMAP_QSPI 0x00
	#define QIXIS_RCW_SRC_QSPI 0x62
	#define QIXIS_LBMAP_ALTBANK 0x20
	#define QIXIS_RST_CTL_RESET 0x31
	#define QIXIS_RCFG_CTL_RECONFIG_IDLE 0x20
	#define QIXIS_RCFG_CTL_RECONFIG_START 0x21
	#define QIXIS_RCFG_CTL_WATCHDOG_ENBLE 0x08
	#define QIXIS_LBMAP_MASK 0x0f
	#define QIXIS_RST_CTL_RESET_EN 0x30
	#endif

	/*
	* I2C
	*/
	#ifdef CONFIG_TARGET_LS2081ARDB
	#define CONFIG_SYS_I2C_FPGA_ADDR 0x66
	#endif
	#define I2C_MUX_PCA_ADDR 0x75
	#define I2C_MUX_PCA_ADDR_PRI 0x75 /* Primary Mux*/

	/* I2C bus multiplexer */
	#define I2C_MUX_CH_DEFAULT 0x8

	/* SPI */

	/*
	* RTC configuration
	*/
	#define RTC
	#ifdef CONFIG_TARGET_LS2081ARDB
	#define CONFIG_SYS_I2C_RTC_ADDR 0x51
	#else
	#define CONFIG_RTC_DS3231 1
	#define CONFIG_SYS_I2C_RTC_ADDR 0x68
	#endif

	#define BOOT_TARGET_DEVICES(func) \
	func(USB, usb, 0) \
	func(MMC, mmc, 0) \
	func(SCSI, scsi, 0) \
	func(DHCP, dhcp, na)
	#include <config_distro_bootcmd.h>

	#ifdef CONFIG_TFABOOT
	#define QSPI_MC_INIT_CMD \
	"sf probe 0:0; " \
	"sf read 0x80640000 0x640000 0x80000; " \
	"env exists secureboot && " \
	"esbc_validate 0x80640000 && " \
	"esbc_validate 0x80680000; " \
	"sf read 0x80a00000 0xa00000 0x200000; " \
	"sf read 0x80e00000 0xe00000 0x100000; " \
	"fsl_mc start mc 0x80a00000 0x80e00000 \0"
	#define SD_MC_INIT_CMD \
	"mmcinfo;mmc read 0x80a00000 0x5000 0x1000;" \
	"mmc read 0x80e00000 0x7000 0x800;" \
	"env exists secureboot && " \
	"mmc read 0x80640000 0x3200 0x20 && " \
	"mmc read 0x80680000 0x3400 0x20 && " \
	"esbc_validate 0x80640000 && " \
	"esbc_validate 0x80680000 ;" \
	"fsl_mc start mc 0x80a00000 0x80e00000\0"
	#define IFC_MC_INIT_CMD \
	"env exists secureboot && " \
	"esbc_validate 0x580640000 && " \
	"esbc_validate 0x580680000; " \
	"fsl_mc start mc 0x580a00000 0x580e00000 \0"
	#else
	#ifdef CONFIG_QSPI_BOOT
	#define MC_INIT_CMD \
	"mcinitcmd=sf probe 0:0; " \
	"sf read 0x80640000 0x640000 0x80000; " \
	"env exists secureboot && " \
	"esbc_validate 0x80640000 && " \
	"esbc_validate 0x80680000; " \
	"sf read 0x80a00000 0xa00000 0x200000; " \
	"sf read 0x80e00000 0xe00000 0x100000; " \
	"fsl_mc start mc 0x80a00000 0x80e00000 \0"
	#elif defined(CONFIG_SD_BOOT)
	#define MC_INIT_CMD \
	"mcinitcmd=mmcinfo;mmc read 0x80a00000 0x5000 0x1000;" \
	"mmc read 0x80e00000 0x7000 0x800;" \
	"env exists secureboot && " \
	"mmc read 0x80640000 0x3200 0x20 && " \
	"mmc read 0x80680000 0x3400 0x20 && " \
	"esbc_validate 0x80640000 && " \
	"esbc_validate 0x80680000 ;" \
	"fsl_mc start mc 0x80a00000 0x80e00000\0" \
	"mcmemsize=0x70000000\0"
	#else
	#define MC_INIT_CMD \
	"mcinitcmd=env exists secureboot && " \
	"esbc_validate 0x580640000 && " \
	"esbc_validate 0x580680000; " \
	"fsl_mc start mc 0x580a00000 0x580e00000 \0"
	#endif
	#endif

	/* Initial environment variables */
	#undef CONFIG_EXTRA_ENV_SETTINGS
	#ifdef CONFIG_TFABOOT
	#define CONFIG_EXTRA_ENV_SETTINGS \
	"hwconfig=fsl_ddr:bank_intlv=auto\0" \
	"ramdisk_addr=0x800000\0" \
	"ramdisk_size=0x2000000\0" \
	"fdt_high=0xa0000000\0" \
	"initrd_high=0xffffffffffffffff\0" \
	"kernel_addr=0x581000000\0" \
	"kernel_start=0x1000000\0" \
	"kernelheader_start=0x800000\0" \
	"scriptaddr=0x80000000\0" \
	"scripthdraddr=0x80080000\0" \
	"fdtheader_addr_r=0x80100000\0" \
	"kernelheader_addr_r=0x80200000\0" \
	"kernelheader_addr=0x580600000\0" \
	"kernel_addr_r=0x81000000\0" \
	"kernelheader_size=0x40000\0" \
	"fdt_addr_r=0x90000000\0" \
	"load_addr=0xa0000000\0" \
	"kernel_size=0x2800000\0" \
	"kernel_addr_sd=0x8000\0" \
	"kernel_size_sd=0x14000\0" \
	"console=ttyAMA0,38400n8\0" \
	"mcmemsize=0x70000000\0" \
	"sd_bootcmd=echo Trying load from SD ..;" \
	"mmcinfo; mmc read $load_addr " \
	"$kernel_addr_sd $kernel_size_sd && " \
	"bootm $load_addr#$board\0" \
	QSPI_MC_INIT_CMD \
	BOOTENV \
	"boot_scripts=ls2088ardb_boot.scr\0" \
	"boot_script_hdr=hdr_ls2088ardb_bs.out\0" \
	"scan_dev_for_boot_part=" \
	"part list ${devtype} ${devnum} devplist; " \
	"env exists devplist \|\| setenv devplist 1; " \
	"for distro_bootpart in ${devplist}; do " \
	"if fstype ${devtype} " \
	"${devnum}:${distro_bootpart} " \
	"bootfstype; then " \
	"run scan_dev_for_boot; " \
	"fi; " \
	"done\0" \
	"boot_a_script=" \
	"load ${devtype} ${devnum}:${distro_bootpart} " \
	"${scriptaddr} ${prefix}${script}; " \
	"env exists secureboot && load ${devtype} " \
	"${devnum}:${distro_bootpart} " \
	"${scripthdraddr} ${prefix}${boot_script_hdr} " \
	"&& esbc_validate ${scripthdraddr};" \
	"source ${scriptaddr}\0" \
	"qspi_bootcmd=echo Trying load from qspi..;" \
	"sf probe && sf read $load_addr " \
	"$kernel_start $kernel_size ; env exists secureboot &&" \
	"sf read $kernelheader_addr_r $kernelheader_start " \
	"$kernelheader_size && esbc_validate ${kernelheader_addr_r}; "\
	" bootm $load_addr#$board\0" \
	"nor_bootcmd=echo Trying load from nor..;" \
	"cp.b $kernel_addr $load_addr " \
	"$kernel_size ; env exists secureboot && " \
	"cp.b $kernelheader_addr $kernelheader_addr_r " \
	"$kernelheader_size && esbc_validate ${kernelheader_addr_r}; "\
	"bootm $load_addr#$board\0"
	#else
	#define CONFIG_EXTRA_ENV_SETTINGS \
	"hwconfig=fsl_ddr:bank_intlv=auto\0" \
	"ramdisk_addr=0x800000\0" \
	"ramdisk_size=0x2000000\0" \
	"fdt_high=0xa0000000\0" \
	"initrd_high=0xffffffffffffffff\0" \
	"kernel_addr=0x581000000\0" \
	"kernel_start=0x1000000\0" \
	"kernelheader_start=0x600000\0" \
	"scriptaddr=0x80000000\0" \
	"scripthdraddr=0x80080000\0" \
	"fdtheader_addr_r=0x80100000\0" \
	"kernelheader_addr_r=0x80200000\0" \
	"kernelheader_addr=0x580600000\0" \
	"kernel_addr_r=0x81000000\0" \
	"kernelheader_size=0x40000\0" \
	"fdt_addr_r=0x90000000\0" \
	"load_addr=0xa0000000\0" \
	"kernel_size=0x2800000\0" \
	"kernel_addr_sd=0x8000\0" \
	"kernel_size_sd=0x14000\0" \
	"console=ttyAMA0,38400n8\0" \
	"mcmemsize=0x70000000\0" \
	"sd_bootcmd=echo Trying load from SD ..;" \
	"mmcinfo; mmc read $load_addr " \
	"$kernel_addr_sd $kernel_size_sd && " \
	"bootm $load_addr#$board\0" \
	MC_INIT_CMD \
	BOOTENV \
	"boot_scripts=ls2088ardb_boot.scr\0" \
	"boot_script_hdr=hdr_ls2088ardb_bs.out\0" \
	"scan_dev_for_boot_part=" \
	"part list ${devtype} ${devnum} devplist; " \
	"env exists devplist \|\| setenv devplist 1; " \
	"for distro_bootpart in ${devplist}; do " \
	"if fstype ${devtype} " \
	"${devnum}:${distro_bootpart} " \
	"bootfstype; then " \
	"run scan_dev_for_boot; " \
	"fi; " \
	"done\0" \
	"boot_a_script=" \
	"load ${devtype} ${devnum}:${distro_bootpart} " \
	"${scriptaddr} ${prefix}${script}; " \
	"env exists secureboot && load ${devtype} " \
	"${devnum}:${distro_bootpart} " \
	"${scripthdraddr} ${prefix}${boot_script_hdr}; " \
	"env exists secureboot " \
	"&& esbc_validate ${scripthdraddr};" \
	"source ${scriptaddr}\0" \
	"qspi_bootcmd=echo Trying load from qspi..;" \
	"sf probe && sf read $load_addr " \
	"$kernel_start $kernel_size ; env exists secureboot &&" \
	"sf read $kernelheader_addr_r $kernelheader_start " \
	"$kernelheader_size && esbc_validate ${kernelheader_addr_r}; "\
	" bootm $load_addr#$board\0" \
	"nor_bootcmd=echo Trying load from nor..;" \
	"cp.b $kernel_addr $load_addr " \
	"$kernel_size ; env exists secureboot && " \
	"cp.b $kernelheader_addr $kernelheader_addr_r " \
	"$kernelheader_size && esbc_validate ${kernelheader_addr_r}; "\
	"bootm $load_addr#$board\0"
	#endif

	#ifdef CONFIG_TFABOOT
	#define QSPI_NOR_BOOTCOMMAND \
	"sf probe 0:0; " \
	"sf read 0x806c0000 0x6c0000 0x40000; " \
	"env exists mcinitcmd && env exists secureboot "\
	"&& esbc_validate 0x806c0000; " \
	"sf read 0x80d00000 0xd00000 0x100000; " \
	"env exists mcinitcmd && " \
	"fsl_mc lazyapply dpl 0x80d00000; " \
	"run distro_bootcmd;run qspi_bootcmd; " \
	"env exists secureboot && esbc_halt;"

	/* Try to boot an on-SD kernel first, then do normal distro boot */
	#define SD_BOOTCOMMAND \
	"env exists mcinitcmd && env exists secureboot "\
	"&& mmcinfo && mmc read $load_addr 0x3600 0x800 " \
	"&& esbc_validate $load_addr; " \
	"env exists mcinitcmd && run mcinitcmd " \
	"&& mmc read 0x80d00000 0x6800 0x800 " \
	"&& fsl_mc lazyapply dpl 0x80d00000; " \
	"run distro_bootcmd;run sd_bootcmd; " \
	"env exists secureboot && esbc_halt;"

	/* Try to boot an on-NOR kernel first, then do normal distro boot */
	#define IFC_NOR_BOOTCOMMAND \
	"env exists mcinitcmd && env exists secureboot "\
	"&& esbc_validate 0x5806C0000; env exists mcinitcmd "\
	"&& fsl_mc lazyapply dpl 0x580d00000;" \
	"run distro_bootcmd;run nor_bootcmd; " \
	"env exists secureboot && esbc_halt;"
	#else
	#ifdef CONFIG_QSPI_BOOT
	/* Try to boot an on-QSPI kernel first, then do normal distro boot */
	#elif defined(CONFIG_SD_BOOT)
	/* Try to boot an on-SD kernel first, then do normal distro boot */
	#else
	/* Try to boot an on-NOR kernel first, then do normal distro boot */
	#endif
	#endif

	/* MAC/PHY configuration */
	#define CORTINA_PHY_ADDR1 0x10
	#define CORTINA_PHY_ADDR2 0x11
	#define CORTINA_PHY_ADDR3 0x12
	#define CORTINA_PHY_ADDR4 0x13
	#define AQ_PHY_ADDR1 0x00
	#define AQ_PHY_ADDR2 0x01
	#define AQ_PHY_ADDR3 0x02
	#define AQ_PHY_ADDR4 0x03
	#define AQR405_IRQ_MASK 0x36

	#include <asm/fsl_secure_boot.h>

	#endif /* __LS2_RDB_H */