| /* SPDX-License-Identifier: GPL-2.0+ */ |
| /* |
| * Copyright 2010-2011 Freescale Semiconductor, Inc. |
| * Copyright 2020 NXP |
| */ |
| |
| /* |
| * QorIQ RDB boards configuration file |
| */ |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| #include <linux/stringify.h> |
| |
| #if defined(CONFIG_TARGET_P1020RDB_PC) |
| #define CONFIG_VSC7385_ENET |
| #define CONFIG_SLIC |
| #define __SW_BOOT_MASK 0x03 |
| #define __SW_BOOT_NOR 0x5c |
| #define __SW_BOOT_SPI 0x1c |
| #define __SW_BOOT_SD 0x9c |
| #define __SW_BOOT_NAND 0xec |
| #define __SW_BOOT_PCIE 0x6c |
| #define __SW_NOR_BANK_MASK 0xfd |
| #define __SW_NOR_BANK_UP 0x00 |
| #define __SW_NOR_BANK_LO 0x02 |
| #define CONFIG_SYS_L2_SIZE (256 << 10) |
| #endif |
| |
| /* |
| * P1020RDB-PD board has user selectable switches for evaluating different |
| * frequency and boot options for the P1020 device. The table that |
| * follow describe the available options. The front six binary number was in |
| * accordance with SW3[1:6]. |
| * 111101 533 533 267 667 NOR Core0 boot; Core1 hold-off |
| * 101101 667 667 333 667 NOR Core0 boot; Core1 hold-off |
| * 011001 800 800 400 667 NOR Core0 boot; Core1 hold-off |
| * 001001 800 800 400 667 SD/MMC Core0 boot; Core1 hold-off |
| * 001101 800 800 400 667 SPI Core0 boot; Core1 hold-off |
| * 010001 800 800 400 667 NAND Core0 boot; Core1 hold-off |
| * 011101 800 800 400 667 PCIe-2 Core0 boot; Core1 hold-off |
| */ |
| #if defined(CONFIG_TARGET_P1020RDB_PD) |
| #define CONFIG_VSC7385_ENET |
| #define CONFIG_SLIC |
| #define __SW_BOOT_MASK 0x03 |
| #define __SW_BOOT_NOR 0x64 |
| #define __SW_BOOT_SPI 0x34 |
| #define __SW_BOOT_SD 0x24 |
| #define __SW_BOOT_NAND 0x44 |
| #define __SW_BOOT_PCIE 0x74 |
| #define __SW_NOR_BANK_MASK 0xfd |
| #define __SW_NOR_BANK_UP 0x00 |
| #define __SW_NOR_BANK_LO 0x02 |
| #define CONFIG_SYS_L2_SIZE (256 << 10) |
| /* |
| * Dynamic MTD Partition support with mtdparts |
| */ |
| #endif |
| |
| #if defined(CONFIG_TARGET_P2020RDB) |
| #define CONFIG_VSC7385_ENET |
| #define __SW_BOOT_MASK 0x03 |
| #define __SW_BOOT_NOR 0xc8 |
| #define __SW_BOOT_SPI 0x28 |
| #define __SW_BOOT_SD 0x68 |
| #define __SW_BOOT_SD2 0x18 |
| #define __SW_BOOT_NAND 0xe8 |
| #define __SW_BOOT_PCIE 0xa8 |
| #define __SW_NOR_BANK_MASK 0xfd |
| #define __SW_NOR_BANK_UP 0x00 |
| #define __SW_NOR_BANK_LO 0x02 |
| #define CONFIG_SYS_L2_SIZE (512 << 10) |
| /* |
| * Dynamic MTD Partition support with mtdparts |
| */ |
| #endif |
| |
| #ifdef CONFIG_SDCARD |
| #define CONFIG_SYS_MMC_U_BOOT_SIZE (768 << 10) |
| #define CONFIG_SYS_MMC_U_BOOT_DST (0x11000000) |
| #define CONFIG_SYS_MMC_U_BOOT_START (0x11000000) |
| #define CONFIG_SYS_MMC_U_BOOT_OFFS (128 << 10) |
| #elif defined(CONFIG_SPIFLASH) |
| #define CONFIG_SYS_SPI_FLASH_U_BOOT_SIZE (768 << 10) |
| #define CONFIG_SYS_SPI_FLASH_U_BOOT_DST (0x11000000) |
| #define CONFIG_SYS_SPI_FLASH_U_BOOT_START (0x11000000) |
| #define CONFIG_SYS_SPI_FLASH_U_BOOT_OFFS (128 << 10) |
| #elif defined(CONFIG_MTD_RAW_NAND) |
| #ifdef CONFIG_TPL_BUILD |
| #define CONFIG_SYS_NAND_U_BOOT_SIZE (832 << 10) |
| #define CONFIG_SYS_NAND_U_BOOT_DST (0x11000000) |
| #define CONFIG_SYS_NAND_U_BOOT_START (0x11000000) |
| #elif defined(CONFIG_SPL_BUILD) |
| #define CONFIG_SYS_NAND_U_BOOT_SIZE (128 << 10) |
| #define CONFIG_SYS_NAND_U_BOOT_DST 0xf8f80000 |
| #define CONFIG_SYS_NAND_U_BOOT_START 0xf8f80000 |
| #endif /* not CONFIG_TPL_BUILD */ |
| #endif |
| |
| #ifndef CONFIG_RESET_VECTOR_ADDRESS |
| #define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc |
| #endif |
| |
| #define CONFIG_HWCONFIG |
| /* |
| * These can be toggled for performance analysis, otherwise use default. |
| */ |
| #define CONFIG_L2_CACHE |
| |
| #define CONFIG_SYS_CCSRBAR 0xffe00000 |
| #define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR |
| |
| /* DDR Setup */ |
| #define SPD_EEPROM_ADDRESS 0x52 |
| |
| #if defined(CONFIG_TARGET_P1020RDB_PD) |
| #define CONFIG_SYS_SDRAM_SIZE_LAW LAW_SIZE_2G |
| #else |
| #define CONFIG_SYS_SDRAM_SIZE_LAW LAW_SIZE_1G |
| #endif |
| #define CONFIG_SYS_SDRAM_SIZE (1u << (CONFIG_SYS_SDRAM_SIZE_LAW - 19)) |
| #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 |
| #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE |
| |
| /* Default settings for DDR3 */ |
| #ifndef CONFIG_TARGET_P2020RDB |
| #define CONFIG_SYS_DDR_CS0_BNDS 0x0000003f |
| #define CONFIG_SYS_DDR_CS0_CONFIG 0x80014302 |
| #define CONFIG_SYS_DDR_CS0_CONFIG_2 0x00000000 |
| #define CONFIG_SYS_DDR_CS1_BNDS 0x0040007f |
| #define CONFIG_SYS_DDR_CS1_CONFIG 0x80014302 |
| #define CONFIG_SYS_DDR_CS1_CONFIG_2 0x00000000 |
| |
| #define CONFIG_SYS_DDR_DATA_INIT 0xdeadbeef |
| #define CONFIG_SYS_DDR_INIT_ADDR 0x00000000 |
| #define CONFIG_SYS_DDR_INIT_EXT_ADDR 0x00000000 |
| #define CONFIG_SYS_DDR_MODE_CONTROL 0x00000000 |
| |
| #define CONFIG_SYS_DDR_ZQ_CONTROL 0x89080600 |
| #define CONFIG_SYS_DDR_WRLVL_CONTROL 0x8655A608 |
| #define CONFIG_SYS_DDR_SR_CNTR 0x00000000 |
| #define CONFIG_SYS_DDR_RCW_1 0x00000000 |
| #define CONFIG_SYS_DDR_RCW_2 0x00000000 |
| #define CONFIG_SYS_DDR_CONTROL 0xC70C0000 /* Type = DDR3 */ |
| #define CONFIG_SYS_DDR_CONTROL_2 0x04401050 |
| #define CONFIG_SYS_DDR_TIMING_4 0x00220001 |
| #define CONFIG_SYS_DDR_TIMING_5 0x03402400 |
| |
| #define CONFIG_SYS_DDR_TIMING_3 0x00020000 |
| #define CONFIG_SYS_DDR_TIMING_0 0x00330004 |
| #define CONFIG_SYS_DDR_TIMING_1 0x6f6B4846 |
| #define CONFIG_SYS_DDR_TIMING_2 0x0FA8C8CF |
| #define CONFIG_SYS_DDR_CLK_CTRL 0x03000000 |
| #define CONFIG_SYS_DDR_MODE_1 0x40461520 |
| #define CONFIG_SYS_DDR_MODE_2 0x8000c000 |
| #define CONFIG_SYS_DDR_INTERVAL 0x0C300000 |
| #endif |
| |
| /* |
| * Memory map |
| * |
| * 0x0000_0000 0x7fff_ffff DDR Up to 2GB cacheable |
| * 0x8000_0000 0xdfff_ffff PCI Express Mem 1.5G non-cacheable(PCIe * 3) |
| * 0xec00_0000 0xefff_ffff NOR flash Up to 64M non-cacheable CS0/1 |
| * 0xf8f8_0000 0xf8ff_ffff L2 SRAM Up to 512K cacheable |
| * (early boot only) |
| * 0xff80_0000 0xff80_7fff NAND flash 32K non-cacheable CS1/0 |
| * 0xffa0_0000 0xffaf_ffff CPLD 1M non-cacheable CS3 |
| * 0xffb0_0000 0xffbf_ffff VSC7385 switch 1M non-cacheable CS2 |
| * 0xffc0_0000 0xffc3_ffff PCI IO range 256k non-cacheable |
| * 0xffd0_0000 0xffd0_3fff L1 for stack 16K cacheable |
| * 0xffe0_0000 0xffef_ffff CCSR 1M non-cacheable |
| */ |
| |
| /* |
| * Local Bus Definitions |
| */ |
| #if defined(CONFIG_TARGET_P1020RDB_PD) |
| #define CONFIG_SYS_MAX_FLASH_SECT 512 /* 64M */ |
| #define CONFIG_SYS_FLASH_BASE 0xec000000 |
| #else |
| #define CONFIG_SYS_MAX_FLASH_SECT 128 /* 16M */ |
| #define CONFIG_SYS_FLASH_BASE 0xef000000 |
| #endif |
| |
| #ifdef CONFIG_PHYS_64BIT |
| #define CONFIG_SYS_FLASH_BASE_PHYS (0xf00000000ull | CONFIG_SYS_FLASH_BASE) |
| #else |
| #define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE |
| #endif |
| |
| #define CONFIG_FLASH_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) \ |
| | BR_PS_16 | BR_V) |
| |
| #define CONFIG_FLASH_OR_PRELIM 0xfc000ff7 |
| |
| #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS} |
| #define CONFIG_SYS_FLASH_QUIET_TEST |
| #define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ |
| |
| #undef CONFIG_SYS_FLASH_CHECKSUM |
| #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ |
| #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ |
| |
| #define CONFIG_SYS_FLASH_EMPTY_INFO |
| |
| /* Nand Flash */ |
| #ifdef CONFIG_NAND_FSL_ELBC |
| #define CONFIG_SYS_NAND_BASE 0xff800000 |
| #ifdef CONFIG_PHYS_64BIT |
| #define CONFIG_SYS_NAND_BASE_PHYS 0xfff800000ull |
| #else |
| #define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE |
| #endif |
| |
| #define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE } |
| #define CONFIG_SYS_MAX_NAND_DEVICE 1 |
| |
| #define CONFIG_SYS_NAND_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ |
| | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \ |
| | BR_PS_8 /* Port Size = 8 bit */ \ |
| | BR_MS_FCM /* MSEL = FCM */ \ |
| | BR_V) /* valid */ |
| #if defined(CONFIG_TARGET_P1020RDB_PD) |
| #define CONFIG_SYS_NAND_OR_PRELIM (OR_AM_32KB \ |
| | OR_FCM_PGS /* Large Page*/ \ |
| | OR_FCM_CSCT \ |
| | OR_FCM_CST \ |
| | OR_FCM_CHT \ |
| | OR_FCM_SCY_1 \ |
| | OR_FCM_TRLX \ |
| | OR_FCM_EHTR) |
| #else |
| #define CONFIG_SYS_NAND_OR_PRELIM (OR_AM_32KB /* small page */ \ |
| | OR_FCM_CSCT \ |
| | OR_FCM_CST \ |
| | OR_FCM_CHT \ |
| | OR_FCM_SCY_1 \ |
| | OR_FCM_TRLX \ |
| | OR_FCM_EHTR) |
| #endif |
| #endif /* CONFIG_NAND_FSL_ELBC */ |
| |
| #define CONFIG_SYS_INIT_RAM_LOCK |
| #define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* stack in RAM */ |
| #ifdef CONFIG_PHYS_64BIT |
| #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf |
| #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR |
| /* The assembler doesn't like typecast */ |
| #define CONFIG_SYS_INIT_RAM_ADDR_PHYS \ |
| ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \ |
| CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW) |
| #else |
| /* Initial L1 address */ |
| #define CONFIG_SYS_INIT_RAM_ADDR_PHYS CONFIG_SYS_INIT_RAM_ADDR |
| #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0 |
| #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS |
| #endif |
| /* Size of used area in RAM */ |
| #define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 |
| |
| #define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) |
| |
| #define CONFIG_SYS_MONITOR_LEN (768 * 1024) |
| |
| #define CONFIG_SYS_CPLD_BASE 0xffa00000 |
| #ifdef CONFIG_PHYS_64BIT |
| #define CONFIG_SYS_CPLD_BASE_PHYS 0xfffa00000ull |
| #else |
| #define CONFIG_SYS_CPLD_BASE_PHYS CONFIG_SYS_CPLD_BASE |
| #endif |
| /* CPLD config size: 1Mb */ |
| |
| /* Vsc7385 switch */ |
| #ifdef CONFIG_VSC7385_ENET |
| #define __VSCFW_ADDR "vscfw_addr=ef000000\0" |
| #define CONFIG_SYS_VSC7385_BASE 0xffb00000 |
| |
| #ifdef CONFIG_PHYS_64BIT |
| #define CONFIG_SYS_VSC7385_BASE_PHYS 0xfffb00000ull |
| #else |
| #define CONFIG_SYS_VSC7385_BASE_PHYS CONFIG_SYS_VSC7385_BASE |
| #endif |
| |
| #define CONFIG_SYS_VSC7385_BR_PRELIM \ |
| (BR_PHYS_ADDR(CONFIG_SYS_VSC7385_BASE_PHYS) | BR_PS_8 | BR_V) |
| #define CONFIG_SYS_VSC7385_OR_PRELIM (OR_AM_128KB | OR_GPCM_CSNT | \ |
| OR_GPCM_XACS | OR_GPCM_SCY_15 | OR_GPCM_SETA | \ |
| OR_GPCM_TRLX | OR_GPCM_EHTR | OR_GPCM_EAD) |
| |
| /* The size of the VSC7385 firmware image */ |
| #define CONFIG_VSC7385_IMAGE_SIZE 8192 |
| #endif |
| |
| #ifndef __VSCFW_ADDR |
| #define __VSCFW_ADDR "" |
| #endif |
| |
| /* |
| * Config the L2 Cache as L2 SRAM |
| */ |
| #if defined(CONFIG_SPL_BUILD) |
| #if defined(CONFIG_SDCARD) || defined(CONFIG_SPIFLASH) |
| #define CONFIG_SYS_INIT_L2_ADDR 0xf8f80000 |
| #define CONFIG_SYS_INIT_L2_ADDR_PHYS CONFIG_SYS_INIT_L2_ADDR |
| #define CONFIG_SYS_INIT_L2_END (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_L2_SIZE) |
| #elif defined(CONFIG_MTD_RAW_NAND) |
| #ifdef CONFIG_TPL_BUILD |
| #define CONFIG_SYS_INIT_L2_ADDR 0xf8f80000 |
| #define CONFIG_SYS_INIT_L2_ADDR_PHYS CONFIG_SYS_INIT_L2_ADDR |
| #define CONFIG_SYS_INIT_L2_END (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_L2_SIZE) |
| #else |
| #define CONFIG_SYS_INIT_L2_ADDR 0xf8f80000 |
| #define CONFIG_SYS_INIT_L2_ADDR_PHYS CONFIG_SYS_INIT_L2_ADDR |
| #define CONFIG_SYS_INIT_L2_END (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_L2_SIZE) |
| #endif /* CONFIG_TPL_BUILD */ |
| #endif |
| #endif |
| |
| /* Serial Port - controlled on board with jumper J8 |
| * open - index 2 |
| * shorted - index 1 |
| */ |
| #undef CONFIG_SERIAL_SOFTWARE_FIFO |
| #define CONFIG_SYS_NS16550_SERIAL |
| #define CONFIG_SYS_NS16550_REG_SIZE 1 |
| #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) |
| #if defined(CONFIG_SPL_BUILD) && CONFIG_IS_ENABLED(INIT_MINIMAL) |
| #define CONFIG_NS16550_MIN_FUNCTIONS |
| #endif |
| |
| #define CONFIG_SYS_BAUDRATE_TABLE \ |
| {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} |
| |
| #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) |
| #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) |
| |
| /* I2C */ |
| #if !CONFIG_IS_ENABLED(DM_I2C) |
| #define CONFIG_SYS_I2C_NOPROBES { {0, 0x29} } |
| #endif |
| |
| /* |
| * I2C2 EEPROM |
| */ |
| |
| #define CONFIG_RTC_PT7C4338 |
| #define CONFIG_SYS_I2C_RTC_ADDR 0x68 |
| #define CONFIG_SYS_I2C_PCA9557_ADDR 0x18 |
| |
| /* enable read and write access to EEPROM */ |
| |
| #if defined(CONFIG_PCI) |
| /* |
| * General PCI |
| * Memory space is mapped 1-1, but I/O space must start from 0. |
| */ |
| |
| /* controller 2, direct to uli, tgtid 2, Base address 9000 */ |
| #define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000 |
| #ifdef CONFIG_PHYS_64BIT |
| #define CONFIG_SYS_PCIE2_MEM_PHYS 0xc20000000ull |
| #else |
| #define CONFIG_SYS_PCIE2_MEM_PHYS 0xa0000000 |
| #endif |
| #define CONFIG_SYS_PCIE2_IO_VIRT 0xffc10000 |
| #ifdef CONFIG_PHYS_64BIT |
| #define CONFIG_SYS_PCIE2_IO_PHYS 0xfffc10000ull |
| #else |
| #define CONFIG_SYS_PCIE2_IO_PHYS 0xffc10000 |
| #endif |
| |
| /* controller 1, Slot 2, tgtid 1, Base address a000 */ |
| #define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000 |
| #ifdef CONFIG_PHYS_64BIT |
| #define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull |
| #else |
| #define CONFIG_SYS_PCIE1_MEM_PHYS 0x80000000 |
| #endif |
| #define CONFIG_SYS_PCIE1_IO_VIRT 0xffc00000 |
| #ifdef CONFIG_PHYS_64BIT |
| #define CONFIG_SYS_PCIE1_IO_PHYS 0xfffc00000ull |
| #else |
| #define CONFIG_SYS_PCIE1_IO_PHYS 0xffc00000 |
| #endif |
| #endif /* CONFIG_PCI */ |
| |
| #if defined(CONFIG_TSEC_ENET) |
| #define CONFIG_TSEC1 |
| #define CONFIG_TSEC1_NAME "eTSEC1" |
| #define CONFIG_TSEC2 |
| #define CONFIG_TSEC2_NAME "eTSEC2" |
| #define CONFIG_TSEC3 |
| #define CONFIG_TSEC3_NAME "eTSEC3" |
| |
| #define TSEC1_PHY_ADDR 2 |
| #define TSEC2_PHY_ADDR 0 |
| #define TSEC3_PHY_ADDR 1 |
| |
| #define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) |
| #define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) |
| #define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) |
| |
| #define TSEC1_PHYIDX 0 |
| #define TSEC2_PHYIDX 0 |
| #define TSEC3_PHYIDX 0 |
| #endif /* CONFIG_TSEC_ENET */ |
| |
| /* |
| * Environment |
| */ |
| #if defined(CONFIG_MTD_RAW_NAND) |
| #ifdef CONFIG_TPL_BUILD |
| #define SPL_ENV_ADDR (CONFIG_SYS_INIT_L2_ADDR + (160 << 10)) |
| #endif |
| #elif defined(CONFIG_SYS_RAMBOOT) |
| #define SPL_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) |
| #endif |
| |
| #define CONFIG_LOADS_ECHO /* echo on for serial download */ |
| #define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */ |
| |
| /* |
| * USB |
| */ |
| |
| #ifdef CONFIG_MMC |
| #define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR |
| #endif |
| |
| /* |
| * Miscellaneous configurable options |
| */ |
| |
| /* |
| * For booting Linux, the board info and command line data |
| * have to be in the first 64 MB of memory, since this is |
| * the maximum mapped by the Linux kernel during initialization. |
| */ |
| #define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory for Linux*/ |
| #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ |
| |
| /* |
| * Environment Configuration |
| */ |
| #define CONFIG_HOSTNAME "unknown" |
| #define CONFIG_ROOTPATH "/opt/nfsroot" |
| #define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */ |
| |
| #include "p1_p2_bootsrc.h" |
| |
| #define CONFIG_EXTRA_ENV_SETTINGS \ |
| "netdev=eth0\0" \ |
| "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \ |
| "loadaddr=1000000\0" \ |
| "bootfile=uImage\0" \ |
| "tftpflash=tftpboot $loadaddr $uboot; " \ |
| "protect off " __stringify(CONFIG_SYS_TEXT_BASE) " +$filesize; " \ |
| "erase " __stringify(CONFIG_SYS_TEXT_BASE) " +$filesize; " \ |
| "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) " $filesize; " \ |
| "protect on " __stringify(CONFIG_SYS_TEXT_BASE) " +$filesize; " \ |
| "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) " $filesize\0" \ |
| "hwconfig=usb1:dr_mode=host,phy_type=ulpi\0" \ |
| "consoledev=ttyS0\0" \ |
| "ramdiskaddr=2000000\0" \ |
| "ramdiskfile=rootfs.ext2.gz.uboot\0" \ |
| "fdtaddr=1e00000\0" \ |
| "bdev=sda1\0" \ |
| "jffs2nor=mtdblock3\0" \ |
| "norbootaddr=ef080000\0" \ |
| "norfdtaddr=ef040000\0" \ |
| "jffs2nand=mtdblock9\0" \ |
| "nandbootaddr=100000\0" \ |
| "nandfdtaddr=80000\0" \ |
| "ramdisk_size=120000\0" \ |
| __VSCFW_ADDR \ |
| MAP_NOR_LO_CMD(map_lowernorbank) \ |
| MAP_NOR_UP_CMD(map_uppernorbank) \ |
| RST_NOR_CMD(norboot) \ |
| RST_SPI_CMD(spiboot) \ |
| RST_SD_CMD(sdboot) \ |
| RST_NAND_CMD(nandboot) \ |
| RST_PCIE_CMD(pciboot) \ |
| "" |
| |
| #define CONFIG_USB_FAT_BOOT \ |
| "setenv bootargs root=/dev/ram rw " \ |
| "console=$consoledev,$baudrate $othbootargs " \ |
| "ramdisk_size=$ramdisk_size;" \ |
| "usb start;" \ |
| "fatload usb 0:2 $loadaddr $bootfile;" \ |
| "fatload usb 0:2 $fdtaddr $fdtfile;" \ |
| "fatload usb 0:2 $ramdiskaddr $ramdiskfile;" \ |
| "bootm $loadaddr $ramdiskaddr $fdtaddr" |
| |
| #define CONFIG_USB_EXT2_BOOT \ |
| "setenv bootargs root=/dev/ram rw " \ |
| "console=$consoledev,$baudrate $othbootargs " \ |
| "ramdisk_size=$ramdisk_size;" \ |
| "usb start;" \ |
| "ext2load usb 0:4 $loadaddr $bootfile;" \ |
| "ext2load usb 0:4 $fdtaddr $fdtfile;" \ |
| "ext2load usb 0:4 $ramdiskaddr $ramdiskfile;" \ |
| "bootm $loadaddr $ramdiskaddr $fdtaddr" |
| |
| #define CONFIG_NORBOOT \ |
| "setenv bootargs root=/dev/$jffs2nor rw " \ |
| "console=$consoledev,$baudrate rootfstype=jffs2 $othbootargs;" \ |
| "bootm $norbootaddr - $norfdtaddr" |
| |
| #endif /* __CONFIG_H */ |