| /* SPDX-License-Identifier: GPL-2.0+ */ |
| /* |
| * Copyright 2009-2012 Freescale Semiconductor, Inc. |
| * Copyright 2020-2021 NXP |
| */ |
| |
| /* |
| * Corenet DS style board configuration file |
| */ |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| #include <linux/stringify.h> |
| |
| #include "../board/freescale/common/ics307_clk.h" |
| |
| #ifdef CONFIG_RAMBOOT_PBL |
| #define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE |
| #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc |
| #endif |
| |
| #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE |
| /* Set 1M boot space */ |
| #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000) |
| #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \ |
| (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR) |
| #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc |
| #endif |
| |
| /* High Level Configuration Options */ |
| #define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */ |
| |
| #ifndef CONFIG_RESET_VECTOR_ADDRESS |
| #define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc |
| #endif |
| |
| #define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */ |
| #define CONFIG_SYS_NUM_CPC CONFIG_SYS_NUM_DDR_CTLRS |
| |
| /* |
| * These can be toggled for performance analysis, otherwise use default. |
| */ |
| #define CONFIG_SYS_CACHE_STASHING |
| #define CONFIG_SYS_INIT_L2CSR0 L2CSR0_L2E |
| #ifdef CONFIG_DDR_ECC |
| #define CONFIG_MEM_INIT_VALUE 0xdeadbeef |
| #endif |
| |
| #define CONFIG_POST CONFIG_SYS_POST_MEMORY /* test POST memory test */ |
| |
| /* |
| * Config the L3 Cache as L3 SRAM |
| */ |
| #define CONFIG_SYS_INIT_L3_ADDR CONFIG_RAMBOOT_TEXT_BASE |
| #ifdef CONFIG_PHYS_64BIT |
| #define CONFIG_SYS_INIT_L3_ADDR_PHYS (0xf00000000ull | CONFIG_RAMBOOT_TEXT_BASE) |
| #else |
| #define CONFIG_SYS_INIT_L3_ADDR_PHYS CONFIG_SYS_INIT_L3_ADDR |
| #endif |
| #define CONFIG_SYS_L3_SIZE (1024 << 10) |
| #define CONFIG_SYS_INIT_L3_END (CONFIG_SYS_INIT_L3_ADDR + CONFIG_SYS_L3_SIZE) |
| |
| #ifdef CONFIG_PHYS_64BIT |
| #define CONFIG_SYS_DCSRBAR 0xf0000000 |
| #define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull |
| #endif |
| |
| /* EEPROM */ |
| #define CONFIG_SYS_I2C_EEPROM_NXID |
| #define CONFIG_SYS_EEPROM_BUS_NUM 0 |
| |
| /* |
| * DDR Setup |
| */ |
| #define CONFIG_VERY_BIG_RAM |
| #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 |
| #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE |
| |
| #define SPD_EEPROM_ADDRESS1 0x51 |
| #define SPD_EEPROM_ADDRESS2 0x52 |
| #define SPD_EEPROM_ADDRESS SPD_EEPROM_ADDRESS1 /* for p3041/p5010 */ |
| #define CONFIG_SYS_SDRAM_SIZE 4096 /* for fixed parameter use */ |
| |
| /* |
| * Local Bus Definitions |
| */ |
| |
| /* Set the local bus clock 1/8 of platform clock */ |
| #define CONFIG_SYS_LBC_LCRR LCRR_CLKDIV_8 |
| |
| #define CONFIG_SYS_FLASH_BASE 0xe0000000 /* Start of PromJet */ |
| #ifdef CONFIG_PHYS_64BIT |
| #define CONFIG_SYS_FLASH_BASE_PHYS 0xfe0000000ull |
| #else |
| #define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE |
| #endif |
| |
| #define CONFIG_SYS_FLASH_BR_PRELIM \ |
| (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000) \ |
| | BR_PS_16 | BR_V) |
| #define CONFIG_SYS_FLASH_OR_PRELIM ((0xf8000ff7 & ~OR_GPCM_SCY & ~OR_GPCM_EHTR) \ |
| | OR_GPCM_SCY_8 | OR_GPCM_EHTR_CLEAR) |
| |
| #define PIXIS_BASE 0xffdf0000 /* PIXIS registers */ |
| #ifdef CONFIG_PHYS_64BIT |
| #define PIXIS_BASE_PHYS 0xfffdf0000ull |
| #else |
| #define PIXIS_BASE_PHYS PIXIS_BASE |
| #endif |
| |
| #define PIXIS_LBMAP_SWITCH 7 |
| #define PIXIS_LBMAP_MASK 0xf0 |
| #define PIXIS_LBMAP_SHIFT 4 |
| #define PIXIS_LBMAP_ALTBANK 0x40 |
| |
| #define CONFIG_SYS_FLASH_QUIET_TEST |
| #define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ |
| |
| #define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ |
| #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ |
| #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ |
| |
| #if defined(CONFIG_RAMBOOT_PBL) |
| #define CONFIG_SYS_RAMBOOT |
| #endif |
| |
| /* Nand Flash */ |
| #ifdef CONFIG_NAND_FSL_ELBC |
| #define CONFIG_SYS_NAND_BASE 0xffa00000 |
| #ifdef CONFIG_PHYS_64BIT |
| #define CONFIG_SYS_NAND_BASE_PHYS 0xfffa00000ull |
| #else |
| #define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE |
| #endif |
| |
| #define CONFIG_SYS_NAND_BASE_LIST {CONFIG_SYS_NAND_BASE} |
| #define CONFIG_SYS_MAX_NAND_DEVICE 1 |
| |
| /* NAND flash config */ |
| #define CONFIG_SYS_NAND_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ |
| | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \ |
| | BR_PS_8 /* Port Size = 8 bit */ \ |
| | BR_MS_FCM /* MSEL = FCM */ \ |
| | BR_V) /* valid */ |
| #define CONFIG_SYS_NAND_OR_PRELIM (0xFFFC0000 /* length 256K */ \ |
| | OR_FCM_PGS /* Large Page*/ \ |
| | OR_FCM_CSCT \ |
| | OR_FCM_CST \ |
| | OR_FCM_CHT \ |
| | OR_FCM_SCY_1 \ |
| | OR_FCM_TRLX \ |
| | OR_FCM_EHTR) |
| #endif /* CONFIG_NAND_FSL_ELBC */ |
| |
| #define CONFIG_SYS_FLASH_EMPTY_INFO |
| #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000, CONFIG_SYS_FLASH_BASE_PHYS} |
| |
| #define CONFIG_HWCONFIG |
| |
| /* define to use L1 as initial stack */ |
| #define CONFIG_L1_INIT_RAM |
| #define CONFIG_SYS_INIT_RAM_LOCK |
| #define CONFIG_SYS_INIT_RAM_ADDR 0xfdd00000 /* Initial L1 address */ |
| #ifdef CONFIG_PHYS_64BIT |
| #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf |
| #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR |
| /* The assembler doesn't like typecast */ |
| #define CONFIG_SYS_INIT_RAM_ADDR_PHYS \ |
| ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \ |
| CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW) |
| #else |
| #define CONFIG_SYS_INIT_RAM_ADDR_PHYS CONFIG_SYS_INIT_RAM_ADDR /* Initial L1 address */ |
| #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0 |
| #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS |
| #endif |
| #define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 /* Size of used area in RAM */ |
| |
| #define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) |
| |
| #define CONFIG_SYS_MONITOR_LEN (768 * 1024) |
| |
| /* Serial Port - controlled on board with jumper J8 |
| * open - index 2 |
| * shorted - index 1 |
| */ |
| #define CONFIG_SYS_NS16550_SERIAL |
| #define CONFIG_SYS_NS16550_REG_SIZE 1 |
| #define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2) |
| |
| #define CONFIG_SYS_BAUDRATE_TABLE \ |
| {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} |
| |
| #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500) |
| #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600) |
| #define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500) |
| #define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600) |
| |
| /* I2C */ |
| |
| /* |
| * RapidIO |
| */ |
| #define CONFIG_SYS_SRIO1_MEM_VIRT 0xa0000000 |
| #ifdef CONFIG_PHYS_64BIT |
| #define CONFIG_SYS_SRIO1_MEM_PHYS 0xc20000000ull |
| #else |
| #define CONFIG_SYS_SRIO1_MEM_PHYS 0xa0000000 |
| #endif |
| #define CONFIG_SYS_SRIO1_MEM_SIZE 0x10000000 /* 256M */ |
| |
| #define CONFIG_SYS_SRIO2_MEM_VIRT 0xb0000000 |
| #ifdef CONFIG_PHYS_64BIT |
| #define CONFIG_SYS_SRIO2_MEM_PHYS 0xc30000000ull |
| #else |
| #define CONFIG_SYS_SRIO2_MEM_PHYS 0xb0000000 |
| #endif |
| #define CONFIG_SYS_SRIO2_MEM_SIZE 0x10000000 /* 256M */ |
| |
| /* |
| * for slave u-boot IMAGE instored in master memory space, |
| * PHYS must be aligned based on the SIZE |
| */ |
| #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef200000ull |
| #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff00000ull |
| #define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x100000 /* 1M */ |
| #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff00000ull |
| /* |
| * for slave UCODE and ENV instored in master memory space, |
| * PHYS must be aligned based on the SIZE |
| */ |
| #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef100000ull |
| #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull |
| #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000 /* 256K */ |
| |
| /* slave core release by master*/ |
| #define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4 |
| #define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */ |
| |
| /* |
| * SRIO_PCIE_BOOT - SLAVE |
| */ |
| #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE |
| #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000 |
| #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \ |
| (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR) |
| #endif |
| |
| /* |
| * eSPI - Enhanced SPI |
| */ |
| |
| /* |
| * General PCI |
| * Memory space is mapped 1-1, but I/O space must start from 0. |
| */ |
| |
| /* controller 1, direct to uli, tgtid 3, Base address 20000 */ |
| #define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000 |
| #define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull |
| #define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000 |
| #define CONFIG_SYS_PCIE1_IO_PHYS 0xff8000000ull |
| |
| /* controller 2, Slot 2, tgtid 2, Base address 201000 */ |
| #define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000 |
| #define CONFIG_SYS_PCIE2_MEM_PHYS 0xc20000000ull |
| #define CONFIG_SYS_PCIE2_IO_VIRT 0xf8010000 |
| #define CONFIG_SYS_PCIE2_IO_PHYS 0xff8010000ull |
| |
| /* controller 3, Slot 1, tgtid 1, Base address 202000 */ |
| #define CONFIG_SYS_PCIE3_MEM_VIRT 0xc0000000 |
| #define CONFIG_SYS_PCIE3_MEM_PHYS 0xc40000000ull |
| #define CONFIG_SYS_PCIE3_IO_VIRT 0xf8020000 |
| #define CONFIG_SYS_PCIE3_IO_PHYS 0xff8020000ull |
| |
| /* controller 4, Base address 203000 */ |
| #define CONFIG_SYS_PCIE4_MEM_PHYS 0xc60000000ull |
| #define CONFIG_SYS_PCIE4_IO_PHYS 0xff8030000ull |
| |
| /* Qman/Bman */ |
| #define CONFIG_SYS_BMAN_NUM_PORTALS 10 |
| #define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000 |
| #ifdef CONFIG_PHYS_64BIT |
| #define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull |
| #else |
| #define CONFIG_SYS_BMAN_MEM_PHYS CONFIG_SYS_BMAN_MEM_BASE |
| #endif |
| #define CONFIG_SYS_BMAN_MEM_SIZE 0x00200000 |
| #define CONFIG_SYS_BMAN_SP_CENA_SIZE 0x4000 |
| #define CONFIG_SYS_BMAN_SP_CINH_SIZE 0x1000 |
| #define CONFIG_SYS_BMAN_CENA_BASE CONFIG_SYS_BMAN_MEM_BASE |
| #define CONFIG_SYS_BMAN_CENA_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1) |
| #define CONFIG_SYS_BMAN_CINH_BASE (CONFIG_SYS_BMAN_MEM_BASE + \ |
| CONFIG_SYS_BMAN_CENA_SIZE) |
| #define CONFIG_SYS_BMAN_CINH_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1) |
| #define CONFIG_SYS_BMAN_SWP_ISDR_REG 0xE08 |
| #define CONFIG_SYS_QMAN_NUM_PORTALS 10 |
| #define CONFIG_SYS_QMAN_MEM_BASE 0xf4200000 |
| #ifdef CONFIG_PHYS_64BIT |
| #define CONFIG_SYS_QMAN_MEM_PHYS 0xff4200000ull |
| #else |
| #define CONFIG_SYS_QMAN_MEM_PHYS CONFIG_SYS_QMAN_MEM_BASE |
| #endif |
| #define CONFIG_SYS_QMAN_MEM_SIZE 0x00200000 |
| #define CONFIG_SYS_QMAN_SP_CENA_SIZE 0x4000 |
| #define CONFIG_SYS_QMAN_SP_CINH_SIZE 0x1000 |
| #define CONFIG_SYS_QMAN_CENA_BASE CONFIG_SYS_QMAN_MEM_BASE |
| #define CONFIG_SYS_QMAN_CENA_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1) |
| #define CONFIG_SYS_QMAN_CINH_BASE (CONFIG_SYS_QMAN_MEM_BASE + \ |
| CONFIG_SYS_QMAN_CENA_SIZE) |
| #define CONFIG_SYS_QMAN_CINH_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1) |
| #define CONFIG_SYS_QMAN_SWP_ISDR_REG 0xE08 |
| |
| #define CONFIG_SYS_DPAA_FMAN |
| #define CONFIG_SYS_DPAA_PME |
| #define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH) |
| |
| #ifdef CONFIG_FMAN_ENET |
| #define CONFIG_SYS_FM1_DTSEC1_PHY_ADDR 0x1c |
| #define CONFIG_SYS_FM1_DTSEC2_PHY_ADDR 0x1d |
| #define CONFIG_SYS_FM1_DTSEC3_PHY_ADDR 0x1e |
| #define CONFIG_SYS_FM1_DTSEC4_PHY_ADDR 0x1f |
| #define CONFIG_SYS_FM1_10GEC1_PHY_ADDR 4 |
| |
| #define CONFIG_SYS_FM2_DTSEC1_PHY_ADDR 0x1c |
| #define CONFIG_SYS_FM2_DTSEC2_PHY_ADDR 0x1d |
| #define CONFIG_SYS_FM2_DTSEC3_PHY_ADDR 0x1e |
| #define CONFIG_SYS_FM2_DTSEC4_PHY_ADDR 0x1f |
| #define CONFIG_SYS_FM2_10GEC1_PHY_ADDR 0 |
| |
| #define CONFIG_SYS_TBIPA_VALUE 8 |
| #endif |
| |
| /* |
| * Environment |
| */ |
| #define CONFIG_LOADS_ECHO /* echo on for serial download */ |
| #define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */ |
| |
| #ifdef CONFIG_MMC |
| #define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR |
| #define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT |
| #endif |
| |
| /* |
| * Miscellaneous configurable options |
| */ |
| |
| /* |
| * For booting Linux, the board info and command line data |
| * have to be in the first 64 MB of memory, since this is |
| * the maximum mapped by the Linux kernel during initialization. |
| */ |
| #define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory map for Linux*/ |
| #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ |
| |
| /* |
| * Environment Configuration |
| */ |
| #define CONFIG_ROOTPATH "/opt/nfsroot" |
| #define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */ |
| |
| #ifdef CONFIG_TARGET_P4080DS |
| #define __USB_PHY_TYPE ulpi |
| #else |
| #define __USB_PHY_TYPE utmi |
| #endif |
| |
| #define CONFIG_EXTRA_ENV_SETTINGS \ |
| "hwconfig=fsl_ddr:ctlr_intlv=cacheline," \ |
| "bank_intlv=cs0_cs1;" \ |
| "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) ";"\ |
| "usb2:dr_mode=peripheral,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\ |
| "netdev=eth0\0" \ |
| "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \ |
| "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \ |
| "tftpflash=tftpboot $loadaddr $uboot && " \ |
| "protect off $ubootaddr +$filesize && " \ |
| "erase $ubootaddr +$filesize && " \ |
| "cp.b $loadaddr $ubootaddr $filesize && " \ |
| "protect on $ubootaddr +$filesize && " \ |
| "cmp.b $loadaddr $ubootaddr $filesize\0" \ |
| "consoledev=ttyS0\0" \ |
| "ramdiskaddr=2000000\0" \ |
| "ramdiskfile=p4080ds/ramdisk.uboot\0" \ |
| "fdtaddr=1e00000\0" \ |
| "fdtfile=p4080ds/p4080ds.dtb\0" \ |
| "bdev=sda3\0" |
| |
| #include <asm/fsl_secure_boot.h> |
| |
| #endif /* __CONFIG_H */ |