ARM: dts: rmobile: Synchronize Gen3 DTs with Linux 5.6.2
Synchronize R-Car Gen3 device trees with Linux 5.6.2,
commit 9fbe5c87eaa9b72db08425c52c373eb5f6537a0a .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
diff --git a/arch/arm/dts/r8a77990-ebisu.dts b/arch/arm/dts/r8a77990-ebisu.dts
index c727725..4fd2b14 100644
--- a/arch/arm/dts/r8a77990-ebisu.dts
+++ b/arch/arm/dts/r8a77990-ebisu.dts
@@ -19,16 +19,10 @@
};
chosen {
- bootargs = "ignore_loglevel rw root=/dev/nfs ip=dhcp";
+ bootargs = "ignore_loglevel rw root=/dev/nfs ip=on";
stdout-path = "serial0:115200n8";
};
- memory@48000000 {
- device_type = "memory";
- /* first 128MB is reserved for secure area. */
- reg = <0x0 0x48000000 0x0 0x38000000>;
- };
-
audio_clkout: audio-clkout {
/*
* This is same as <&rcar_sound 0>
@@ -107,36 +101,10 @@
};
};
- vga {
- compatible = "vga-connector";
-
- port {
- vga_in: endpoint {
- remote-endpoint = <&adv7123_out>;
- };
- };
- };
-
- vga-encoder {
- compatible = "adi,adv7123";
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- reg = <0>;
- adv7123_in: endpoint {
- remote-endpoint = <&du_out_rgb>;
- };
- };
- port@1 {
- reg = <1>;
- adv7123_out: endpoint {
- remote-endpoint = <&vga_in>;
- };
- };
- };
+ memory@48000000 {
+ device_type = "memory";
+ /* first 128MB is reserved for secure area. */
+ reg = <0x0 0x48000000 0x0 0x38000000>;
};
reg_1p8v: regulator0 {
@@ -157,15 +125,13 @@
regulator-always-on;
};
- vbus0_usb2: regulator-vbus0-usb2 {
+ reg_12p0v: regulator2 {
compatible = "regulator-fixed";
-
- regulator-name = "USB20_VBUS_CN";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
-
- gpio = <&gpio6 4 GPIO_ACTIVE_HIGH>;
- enable-active-high;
+ regulator-name = "D12.0V";
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ regulator-boot-on;
+ regulator-always-on;
};
rsnd_ak4613: sound {
@@ -176,34 +142,24 @@
simple-audio-card,bitclock-master = <&sndcpu>;
simple-audio-card,frame-master = <&sndcpu>;
- sndcpu: simple-audio-card,cpu {
- sound-dai = <&rcar_sound>;
- };
-
sndcodec: simple-audio-card,codec {
sound-dai = <&ak4613>;
};
- };
- x12_clk: x12 {
- compatible = "fixed-clock";
- #clock-cells = <0>;
- clock-frequency = <24576000>;
+ sndcpu: simple-audio-card,cpu {
+ sound-dai = <&rcar_sound>;
+ };
};
- reg_12p0v: regulator2 {
+ vbus0_usb2: regulator-vbus0-usb2 {
compatible = "regulator-fixed";
- regulator-name = "D12.0V";
- regulator-min-microvolt = <12000000>;
- regulator-max-microvolt = <12000000>;
- regulator-boot-on;
- regulator-always-on;
- };
- x13_clk: x13 {
- compatible = "fixed-clock";
- #clock-cells = <0>;
- clock-frequency = <74250000>;
+ regulator-name = "USB20_VBUS_CN";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+
+ gpio = <&gpio6 4 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
};
vcc_sdhi0: regulator-vcc-sdhi0 {
@@ -226,8 +182,7 @@
gpios = <&gpio5 18 GPIO_ACTIVE_HIGH>;
gpios-states = <1>;
- states = <3300000 1
- 1800000 0>;
+ states = <3300000 1>, <1800000 0>;
};
vcc_sdhi1: regulator-vcc-sdhi1 {
@@ -250,8 +205,51 @@
gpios = <&gpio3 15 GPIO_ACTIVE_HIGH>;
gpios-states = <1>;
- states = <3300000 1
- 1800000 0>;
+ states = <3300000 1>, <1800000 0>;
+ };
+
+ vga {
+ compatible = "vga-connector";
+
+ port {
+ vga_in: endpoint {
+ remote-endpoint = <&adv7123_out>;
+ };
+ };
+ };
+
+ vga-encoder {
+ compatible = "adi,adv7123";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ adv7123_in: endpoint {
+ remote-endpoint = <&du_out_rgb>;
+ };
+ };
+ port@1 {
+ reg = <1>;
+ adv7123_out: endpoint {
+ remote-endpoint = <&vga_in>;
+ };
+ };
+ };
+ };
+
+ x12_clk: x12 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <24576000>;
+ };
+
+ x13_clk: x13 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <74250000>;
};
};
@@ -262,7 +260,6 @@
&avb {
pinctrl-0 = <&avb_pins>;
pinctrl-names = "default";
- renesas,no-ether-link;
phy-handle = <&phy0>;
status = "okay";
@@ -272,6 +269,14 @@
interrupt-parent = <&gpio2>;
interrupts = <21 IRQ_TYPE_LEVEL_LOW>;
reset-gpios = <&gpio1 20 GPIO_ACTIVE_LOW>;
+ /*
+ * TX clock internal delay mode is required for reliable
+ * 1Gbps communication using the KSZ9031RNX phy present on
+ * the Ebisu board, however, TX clock internal delay mode
+ * isn't supported on r8a77990. Thus, limit speed to
+ * 100Mbps for reliable communication.
+ */
+ max-speed = <100>;
};
};
@@ -548,6 +553,11 @@
function = "pwm5";
};
+ scif2_pins: scif2 {
+ groups = "scif2_data_a";
+ function = "scif2";
+ };
+
sdhi0_pins: sd0 {
groups = "sdhi0_data4", "sdhi0_ctrl";
function = "sdhi0";
@@ -578,20 +588,15 @@
power-source = <1800>;
};
- sound_pins: sound {
- groups = "ssi01239_ctrl", "ssi0_data", "ssi1_data";
- function = "ssi";
- };
-
sound_clk_pins: sound_clk {
groups = "audio_clk_a", "audio_clk_b_a", "audio_clk_c_a",
"audio_clkout_a", "audio_clkout1_a";
function = "audio_clk";
};
- scif2_pins: scif2 {
- groups = "scif2_data_a";
- function = "scif2";
+ sound_pins: sound {
+ groups = "ssi01239_ctrl", "ssi0_data", "ssi1_data";
+ function = "ssi";
};
usb0_pins: usb {
@@ -629,7 +634,6 @@
/* audio_clkout0/1/2/3 */
#clock-cells = <1>;
clock-frequency = <12288000 11289600>;
- clkout-lr-synchronous;
status = "okay";
@@ -669,41 +673,9 @@
pinctrl-0 = <&scif2_pins>;
pinctrl-names = "default";
- status = "okay";
-};
-
-&ssi1 {
- shared-pin;
-};
-
-&usb2_phy0 {
- pinctrl-0 = <&usb0_pins>;
- pinctrl-names = "default";
-
- vbus-supply = <&vbus0_usb2>;
status = "okay";
};
-&usb3_peri0 {
- companion = <&xhci0>;
- status = "okay";
-};
-
-&vin4 {
- status = "okay";
-};
-
-&vin5 {
- status = "okay";
-};
-
-&xhci0 {
- pinctrl-0 = <&usb30_pins>;
- pinctrl-names = "default";
-
- status = "okay";
-};
-
&sdhi0 {
pinctrl-0 = <&sdhi0_pins>;
pinctrl-1 = <&sdhi0_pins_uhs>;
@@ -747,3 +719,35 @@
non-removable;
status = "okay";
};
+
+&ssi1 {
+ shared-pin;
+};
+
+&usb2_phy0 {
+ pinctrl-0 = <&usb0_pins>;
+ pinctrl-names = "default";
+
+ vbus-supply = <&vbus0_usb2>;
+ status = "okay";
+};
+
+&usb3_peri0 {
+ companion = <&xhci0>;
+ status = "okay";
+};
+
+&vin4 {
+ status = "okay";
+};
+
+&vin5 {
+ status = "okay";
+};
+
+&xhci0 {
+ pinctrl-0 = <&usb30_pins>;
+ pinctrl-names = "default";
+
+ status = "okay";
+};