diff --git a/arch/arm/dts/r8a77990-ebisu.dts b/arch/arm/dts/r8a77990-ebisu.dts
index c727725..4fd2b14 100644
--- a/arch/arm/dts/r8a77990-ebisu.dts
+++ b/arch/arm/dts/r8a77990-ebisu.dts
@@ -19,16 +19,10 @@
 	};
 
 	chosen {
-		bootargs = "ignore_loglevel rw root=/dev/nfs ip=dhcp";
+		bootargs = "ignore_loglevel rw root=/dev/nfs ip=on";
 		stdout-path = "serial0:115200n8";
 	};
 
-	memory@48000000 {
-		device_type = "memory";
-		/* first 128MB is reserved for secure area. */
-		reg = <0x0 0x48000000 0x0 0x38000000>;
-	};
-
 	audio_clkout: audio-clkout {
 		/*
 		 * This is same as <&rcar_sound 0>
@@ -107,36 +101,10 @@
 		};
 	};
 
-	vga {
-		compatible = "vga-connector";
-
-		port {
-			vga_in: endpoint {
-				remote-endpoint = <&adv7123_out>;
-			};
-		};
-	};
-
-	vga-encoder {
-		compatible = "adi,adv7123";
-
-		ports {
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			port@0 {
-				reg = <0>;
-				adv7123_in: endpoint {
-					remote-endpoint = <&du_out_rgb>;
-				};
-			};
-			port@1 {
-				reg = <1>;
-				adv7123_out: endpoint {
-					remote-endpoint = <&vga_in>;
-				};
-			};
-		};
+	memory@48000000 {
+		device_type = "memory";
+		/* first 128MB is reserved for secure area. */
+		reg = <0x0 0x48000000 0x0 0x38000000>;
 	};
 
 	reg_1p8v: regulator0 {
@@ -157,15 +125,13 @@
 		regulator-always-on;
 	};
 
-	vbus0_usb2: regulator-vbus0-usb2 {
+	reg_12p0v: regulator2 {
 		compatible = "regulator-fixed";
-
-		regulator-name = "USB20_VBUS_CN";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-
-		gpio = <&gpio6 4 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
+		regulator-name = "D12.0V";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		regulator-boot-on;
+		regulator-always-on;
 	};
 
 	rsnd_ak4613: sound {
@@ -176,34 +142,24 @@
 		simple-audio-card,bitclock-master = <&sndcpu>;
 		simple-audio-card,frame-master = <&sndcpu>;
 
-		sndcpu: simple-audio-card,cpu {
-			sound-dai = <&rcar_sound>;
-		};
-
 		sndcodec: simple-audio-card,codec {
 			sound-dai = <&ak4613>;
 		};
-	};
 
-	x12_clk: x12 {
-		compatible = "fixed-clock";
-		#clock-cells = <0>;
-		clock-frequency = <24576000>;
+		sndcpu: simple-audio-card,cpu {
+			sound-dai = <&rcar_sound>;
+		};
 	};
 
-	reg_12p0v: regulator2 {
+	vbus0_usb2: regulator-vbus0-usb2 {
 		compatible = "regulator-fixed";
-		regulator-name = "D12.0V";
-		regulator-min-microvolt = <12000000>;
-		regulator-max-microvolt = <12000000>;
-		regulator-boot-on;
-		regulator-always-on;
-	};
 
-	x13_clk: x13 {
-		compatible = "fixed-clock";
-		#clock-cells = <0>;
-		clock-frequency = <74250000>;
+		regulator-name = "USB20_VBUS_CN";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+
+		gpio = <&gpio6 4 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
 	};
 
 	vcc_sdhi0: regulator-vcc-sdhi0 {
@@ -226,8 +182,7 @@
 
 		gpios = <&gpio5 18 GPIO_ACTIVE_HIGH>;
 		gpios-states = <1>;
-		states = <3300000 1
-			  1800000 0>;
+		states = <3300000 1>, <1800000 0>;
 	};
 
 	vcc_sdhi1: regulator-vcc-sdhi1 {
@@ -250,8 +205,51 @@
 
 		gpios = <&gpio3 15 GPIO_ACTIVE_HIGH>;
 		gpios-states = <1>;
-		states = <3300000 1
-			  1800000 0>;
+		states = <3300000 1>, <1800000 0>;
+	};
+
+	vga {
+		compatible = "vga-connector";
+
+		port {
+			vga_in: endpoint {
+				remote-endpoint = <&adv7123_out>;
+			};
+		};
+	};
+
+	vga-encoder {
+		compatible = "adi,adv7123";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				adv7123_in: endpoint {
+					remote-endpoint = <&du_out_rgb>;
+				};
+			};
+			port@1 {
+				reg = <1>;
+				adv7123_out: endpoint {
+					remote-endpoint = <&vga_in>;
+				};
+			};
+		};
+	};
+
+	x12_clk: x12 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <24576000>;
+	};
+
+	x13_clk: x13 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <74250000>;
 	};
 };
 
@@ -262,7 +260,6 @@
 &avb {
 	pinctrl-0 = <&avb_pins>;
 	pinctrl-names = "default";
-	renesas,no-ether-link;
 	phy-handle = <&phy0>;
 	status = "okay";
 
@@ -272,6 +269,14 @@
 		interrupt-parent = <&gpio2>;
 		interrupts = <21 IRQ_TYPE_LEVEL_LOW>;
 		reset-gpios = <&gpio1 20 GPIO_ACTIVE_LOW>;
+		/*
+		 * TX clock internal delay mode is required for reliable
+		 * 1Gbps communication using the KSZ9031RNX phy present on
+		 * the Ebisu board, however, TX clock internal delay mode
+		 * isn't supported on r8a77990.  Thus, limit speed to
+		 * 100Mbps for reliable communication.
+		 */
+		max-speed = <100>;
 	};
 };
 
@@ -548,6 +553,11 @@
 		function = "pwm5";
 	};
 
+	scif2_pins: scif2 {
+		groups = "scif2_data_a";
+		function = "scif2";
+	};
+
 	sdhi0_pins: sd0 {
 		groups = "sdhi0_data4", "sdhi0_ctrl";
 		function = "sdhi0";
@@ -578,20 +588,15 @@
 		power-source = <1800>;
 	};
 
-	sound_pins: sound {
-		groups = "ssi01239_ctrl", "ssi0_data", "ssi1_data";
-		function = "ssi";
-	};
-
 	sound_clk_pins: sound_clk {
 		groups = "audio_clk_a", "audio_clk_b_a", "audio_clk_c_a",
 			 "audio_clkout_a", "audio_clkout1_a";
 		function = "audio_clk";
 	};
 
-	scif2_pins: scif2 {
-		groups = "scif2_data_a";
-		function = "scif2";
+	sound_pins: sound {
+		groups = "ssi01239_ctrl", "ssi0_data", "ssi1_data";
+		function = "ssi";
 	};
 
 	usb0_pins: usb {
@@ -629,7 +634,6 @@
 	/* audio_clkout0/1/2/3 */
 	#clock-cells = <1>;
 	clock-frequency = <12288000 11289600>;
-	clkout-lr-synchronous;
 
 	status = "okay";
 
@@ -669,41 +673,9 @@
 	pinctrl-0 = <&scif2_pins>;
 	pinctrl-names = "default";
 
-	status = "okay";
-};
-
-&ssi1 {
-	shared-pin;
-};
-
-&usb2_phy0 {
-	pinctrl-0 = <&usb0_pins>;
-	pinctrl-names = "default";
-
-	vbus-supply = <&vbus0_usb2>;
 	status = "okay";
 };
 
-&usb3_peri0 {
-	companion = <&xhci0>;
-	status = "okay";
-};
-
-&vin4 {
-	status = "okay";
-};
-
-&vin5 {
-	status = "okay";
-};
-
-&xhci0 {
-	pinctrl-0 = <&usb30_pins>;
-	pinctrl-names = "default";
-
-	status = "okay";
-};
-
 &sdhi0 {
 	pinctrl-0 = <&sdhi0_pins>;
 	pinctrl-1 = <&sdhi0_pins_uhs>;
@@ -747,3 +719,35 @@
 	non-removable;
 	status = "okay";
 };
+
+&ssi1 {
+	shared-pin;
+};
+
+&usb2_phy0 {
+	pinctrl-0 = <&usb0_pins>;
+	pinctrl-names = "default";
+
+	vbus-supply = <&vbus0_usb2>;
+	status = "okay";
+};
+
+&usb3_peri0 {
+	companion = <&xhci0>;
+	status = "okay";
+};
+
+&vin4 {
+	status = "okay";
+};
+
+&vin5 {
+	status = "okay";
+};
+
+&xhci0 {
+	pinctrl-0 = <&usb30_pins>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};