| /* |
| * include/configs/ulcb.h |
| * This file is ULCB board configuration. |
| * |
| * Copyright (C) 2017 Renesas Electronics Corporation |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| #ifndef __ULCB_H |
| #define __ULCB_H |
| |
| #undef DEBUG |
| |
| #define CONFIG_RCAR_BOARD_STRING "ULCB" |
| |
| #include "rcar-gen3-common.h" |
| |
| /* M3 ULCB has 2 banks, each with 1 GiB of RAM */ |
| #if defined(CONFIG_R8A7796) |
| #undef PHYS_SDRAM_1_SIZE |
| #undef PHYS_SDRAM_2_SIZE |
| #define PHYS_SDRAM_1_SIZE (0x40000000u - DRAM_RSV_SIZE) |
| #define PHYS_SDRAM_2_SIZE 0x40000000u |
| #endif |
| |
| /* SCIF */ |
| #define CONFIG_SCIF_CONSOLE |
| #define CONFIG_CONS_SCIF2 |
| #define CONFIG_CONS_INDEX 2 |
| #define CONFIG_SH_SCIF_CLK_FREQ CONFIG_S3D4_CLK_FREQ |
| |
| /* [A] Hyper Flash */ |
| /* use to RPC(SPI Multi I/O Bus Controller) */ |
| |
| /* Ethernet RAVB */ |
| #define CONFIG_NET_MULTI |
| #define CONFIG_PHY_MICREL |
| #define CONFIG_BITBANGMII |
| #define CONFIG_BITBANGMII_MULTI |
| |
| /* Board Clock */ |
| /* XTAL_CLK : 33.33MHz */ |
| #define RCAR_XTAL_CLK 33333333u |
| #define CONFIG_SYS_CLK_FREQ RCAR_XTAL_CLK |
| /* ch0to2 CPclk, ch3to11 S3D2_PEREclk, ch12to14 S3D2_RTclk */ |
| /* CPclk 16.66MHz, S3D2 133.33MHz , S3D4 66.66MHz */ |
| #define CONFIG_CP_CLK_FREQ (CONFIG_SYS_CLK_FREQ / 2) |
| #define CONFIG_PLL1_CLK_FREQ (CONFIG_SYS_CLK_FREQ * 192 / 2) |
| #define CONFIG_S3D2_CLK_FREQ (266666666u/2) |
| #define CONFIG_S3D4_CLK_FREQ (266666666u/4) |
| |
| /* Generic Timer Definitions (use in assembler source) */ |
| #define COUNTER_FREQUENCY 0xFE502A /* 16.66MHz from CPclk */ |
| |
| /* Generic Interrupt Controller Definitions */ |
| #define CONFIG_GICV2 |
| #define GICD_BASE 0xF1010000 |
| #define GICC_BASE 0xF1020000 |
| |
| /* CPLD SPI */ |
| #define CONFIG_CMD_SPI |
| #define CONFIG_SOFT_SPI |
| #define SPI_DELAY udelay(0) |
| #define SPI_SDA(val) ulcb_softspi_sda(val) |
| #define SPI_SCL(val) ulcb_softspi_scl(val) |
| #define SPI_READ ulcb_softspi_read() |
| #ifndef __ASSEMBLY__ |
| void ulcb_softspi_sda(int); |
| void ulcb_softspi_scl(int); |
| unsigned char ulcb_softspi_read(void); |
| #endif |
| |
| /* i2c */ |
| #define CONFIG_SYS_I2C |
| #define CONFIG_SYS_I2C_SH |
| #define CONFIG_SYS_I2C_SLAVE 0x60 |
| #define CONFIG_SYS_I2C_SH_NUM_CONTROLLERS 1 |
| #define CONFIG_SYS_I2C_SH_SPEED0 400000 |
| #define CONFIG_SH_I2C_DATA_HIGH 4 |
| #define CONFIG_SH_I2C_DATA_LOW 5 |
| #define CONFIG_SH_I2C_CLOCK 10000000 |
| |
| #define CONFIG_SYS_I2C_POWERIC_ADDR 0x30 |
| |
| /* USB */ |
| #ifdef CONFIG_R8A7795 |
| #define CONFIG_USB_MAX_CONTROLLER_COUNT 3 |
| #else |
| #define CONFIG_USB_MAX_CONTROLLER_COUNT 2 |
| #endif |
| |
| /* SDHI */ |
| #define CONFIG_SH_SDHI_FREQ 200000000 |
| |
| /* Environment in eMMC, at the end of 2nd "boot sector" */ |
| #define CONFIG_ENV_IS_IN_MMC |
| #define CONFIG_ENV_OFFSET (-CONFIG_ENV_SIZE) |
| #define CONFIG_SYS_MMC_ENV_DEV 1 |
| #define CONFIG_SYS_MMC_ENV_PART 2 |
| |
| /* Module stop status bits */ |
| /* MFIS, SCIF1 */ |
| #define CONFIG_SMSTP2_ENA 0x00002040 |
| /* SCIF2 */ |
| #define CONFIG_SMSTP3_ENA 0x00000400 |
| /* INTC-AP, IRQC */ |
| #define CONFIG_SMSTP4_ENA 0x00000180 |
| |
| #endif /* __ULCB_H */ |