| /* |
| * Copyright (C) 2006 Freescale Semiconductor, Inc. |
| * Dave Liu <daveliu@freescale.com> |
| * |
| * Copyright (C) 2007 Logic Product Development, Inc. |
| * Peter Barada <peterb@logicpd.com> |
| * |
| * Copyright (C) 2007 MontaVista Software, Inc. |
| * Anton Vorontsov <avorontsov@ru.mvista.com> |
| * |
| * (C) Copyright 2008 |
| * Heiko Schocher, DENX Software Engineering, hs@denx.de. |
| * |
| * This program is free software; you can redistribute it and/or |
| * modify it under the terms of the GNU General Public License as |
| * published by the Free Software Foundation; either version 2 of |
| * the License, or (at your option) any later version. |
| */ |
| |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| /* |
| * High Level Configuration Options |
| */ |
| #define CONFIG_E300 1 /* E300 family */ |
| #define CONFIG_QE 1 /* Has QE */ |
| #define CONFIG_MPC83XX 1 /* MPC83XX family */ |
| #define CONFIG_MPC8360 1 /* MPC8360 CPU specific */ |
| #define CONFIG_KMETER1 1 /* KMETER1 board specific */ |
| #define CONFIG_HOSTNAME kmeter1 |
| |
| /* include common defines/options for all Keymile boards */ |
| #include "keymile-common.h" |
| |
| #define CONFIG_MISC_INIT_R 1 |
| /* |
| * System Clock Setup |
| */ |
| #define CONFIG_83XX_CLKIN 66000000 |
| #define CONFIG_SYS_CLK_FREQ 66000000 |
| #define CONFIG_83XX_PCICLK 66000000 |
| |
| /* |
| * Hardware Reset Configuration Word |
| */ |
| #define CONFIG_SYS_HRCW_LOW (\ |
| HRCWL_CSB_TO_CLKIN_4X1 | \ |
| HRCWL_CORE_TO_CSB_2X1 | \ |
| HRCWL_CE_PLL_VCO_DIV_2 | \ |
| HRCWL_CE_TO_PLL_1X6 ) |
| |
| #define CONFIG_SYS_HRCW_HIGH (\ |
| HRCWH_CORE_ENABLE | \ |
| HRCWH_FROM_0X00000100 | \ |
| HRCWH_BOOTSEQ_DISABLE | \ |
| HRCWH_SW_WATCHDOG_DISABLE | \ |
| HRCWH_ROM_LOC_LOCAL_16BIT | \ |
| HRCWH_BIG_ENDIAN | \ |
| HRCWH_LALE_EARLY | \ |
| HRCWH_LDP_CLEAR ) |
| |
| /* |
| * System IO Config |
| */ |
| #define CONFIG_SYS_SICRH 0x00000006 |
| #define CONFIG_SYS_SICRL 0x00000000 |
| |
| /* |
| * IMMR new address |
| */ |
| #define CONFIG_SYS_IMMR 0xE0000000 |
| |
| /* |
| * DDR Setup |
| */ |
| #define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory */ |
| #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE |
| #define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE |
| #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN | \ |
| DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05) |
| |
| #define CFG_83XX_DDR_USES_CS0 |
| |
| #undef CONFIG_DDR_ECC |
| |
| /* |
| * DDRCDR - DDR Control Driver Register |
| */ |
| |
| #undef CONFIG_SPD_EEPROM /* Do not use SPD EEPROM for DDR setup */ |
| |
| /* |
| * Manually set up DDR parameters |
| */ |
| #define CONFIG_DDR_II |
| #define CONFIG_SYS_DDR_SIZE 2048 /* MB */ |
| #define CONFIG_SYS_DDR_CS0_BNDS 0x0000007f |
| #define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN | CSCONFIG_AP | \ |
| CSCONFIG_ROW_BIT_13 | \ |
| CSCONFIG_COL_BIT_10 | CSCONFIG_ODT_WR_ACS) |
| |
| #define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SDRAM_TYPE_DDR2 | \ |
| SDRAM_CFG_SREN) |
| #define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000 |
| #define CONFIG_SYS_DDR_CLK_CNTL (DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05) |
| #define CONFIG_SYS_DDR_INTERVAL ((0x080 << SDRAM_INTERVAL_BSTOPRE_SHIFT) | \ |
| (0x3cf << SDRAM_INTERVAL_REFINT_SHIFT)) |
| |
| #define CONFIG_SYS_DDRCDR 0x40000001 |
| #define CONFIG_SYS_DDR_MODE 0x47860452 |
| #define CONFIG_SYS_DDR_MODE2 0x8080c000 |
| |
| #define CONFIG_SYS_DDR_TIMING_0 ((2 << TIMING_CFG0_MRS_CYC_SHIFT) | \ |
| (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \ |
| (6 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \ |
| (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \ |
| (0 << TIMING_CFG0_WWT_SHIFT) | \ |
| (0 << TIMING_CFG0_RRT_SHIFT) | \ |
| (0 << TIMING_CFG0_WRT_SHIFT) | \ |
| (0 << TIMING_CFG0_RWT_SHIFT)) |
| |
| #define CONFIG_SYS_DDR_TIMING_1 (( TIMING_CFG1_CASLAT_50) | \ |
| ( 2 << TIMING_CFG1_WRTORD_SHIFT) | \ |
| ( 2 << TIMING_CFG1_ACTTOACT_SHIFT) | \ |
| ( 3 << TIMING_CFG1_WRREC_SHIFT) | \ |
| ( 7 << TIMING_CFG1_REFREC_SHIFT) | \ |
| ( 3 << TIMING_CFG1_ACTTORW_SHIFT) | \ |
| ( 8 << TIMING_CFG1_ACTTOPRE_SHIFT) | \ |
| ( 3 << TIMING_CFG1_PRETOACT_SHIFT)) |
| |
| #define CONFIG_SYS_DDR_TIMING_2 ((8 << TIMING_CFG2_FOUR_ACT_SHIFT) | \ |
| (3 << TIMING_CFG2_CKE_PLS_SHIFT) | \ |
| (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \ |
| (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \ |
| (4 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \ |
| (0 << TIMING_CFG2_ADD_LAT_SHIFT) | \ |
| (5 << TIMING_CFG2_CPO_SHIFT)) |
| |
| #define CONFIG_SYS_DDR_TIMING_3 0x00000000 |
| |
| /* |
| * The reserved memory |
| */ |
| #define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */ |
| #define CONFIG_SYS_FLASH_BASE 0xF0000000 |
| #define CONFIG_SYS_FLASH_BASE_1 0xF2000000 |
| #define CONFIG_SYS_PIGGY_BASE 0xE8000000 |
| #define CONFIG_SYS_PIGGY_SIZE 128 |
| #define CONFIG_SYS_PAXE_BASE 0xA0000000 |
| #define CONFIG_SYS_PAXE_SIZE 512 |
| |
| #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) |
| #define CONFIG_SYS_RAMBOOT |
| #else |
| #undef CONFIG_SYS_RAMBOOT |
| #endif |
| |
| #define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 256 kB for Mon */ |
| #define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ |
| |
| /* |
| * Initial RAM Base Address Setup |
| */ |
| #define CONFIG_SYS_INIT_RAM_LOCK 1 |
| #define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */ |
| #define CONFIG_SYS_INIT_RAM_END 0x1000 /* End of used area in RAM */ |
| #define CONFIG_SYS_GBL_DATA_SIZE 0x100 /* num bytes initial data */ |
| #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) |
| |
| /* |
| * Local Bus Configuration & Clock Setup |
| */ |
| #define CONFIG_SYS_LCRR (LCRR_DBYP | LCRR_EADC_2 | LCRR_CLKDIV_4) |
| |
| /* |
| * Init Local Bus Memory Controller: |
| * |
| * Bank Bus Machine PortSz Size Device |
| * ---- --- ------- ------ ----- ------ |
| * 0 Local GPCM 16 bit 256MB FLASH |
| * 1 Local GPCM 8 bit 128MB GPIO/PIGGY |
| * 3 Local GPCM 8 bit 512MB PAXE |
| * |
| */ |
| /* |
| * FLASH on the Local Bus |
| */ |
| #define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */ |
| #define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */ |
| #define CONFIG_SYS_FLASH_SIZE 256 /* max FLASH size is 256M */ |
| #define CONFIG_SYS_FLASH_PROTECTION 1 |
| #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 |
| |
| #define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE /* Window base at flash base */ |
| #define CONFIG_SYS_LBLAWAR0_PRELIM 0x8000001b /* 256MB window size */ |
| |
| #define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | \ |
| (2 << BR_PS_SHIFT) | /* 16 bit port size */ \ |
| BR_V) |
| |
| #define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) | \ |
| OR_GPCM_CSNT | OR_GPCM_ACS_DIV2 | \ |
| OR_GPCM_SCY_5 | \ |
| OR_GPCM_TRLX | OR_GPCM_EAD) |
| |
| #define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max num of flash banks */ |
| #define CONFIG_SYS_MAX_FLASH_SECT 512 /* max num of sects on one chip */ |
| #define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE_1 } |
| |
| #undef CONFIG_SYS_FLASH_CHECKSUM |
| |
| /* |
| * PRIO1/PIGGY on the local bus CS1 |
| */ |
| #define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_PIGGY_BASE /* Window base at flash base */ |
| #define CONFIG_SYS_LBLAWAR1_PRELIM 0x8000001A /* 128MB window size */ |
| |
| #define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_PIGGY_BASE | \ |
| (1 << BR_PS_SHIFT) | /* 8 bit port size */ \ |
| BR_V) |
| #define CONFIG_SYS_OR1_PRELIM (MEG_TO_AM(CONFIG_SYS_PIGGY_SIZE) | /* 128MB */ \ |
| OR_GPCM_CSNT | OR_GPCM_ACS_DIV2 | \ |
| OR_GPCM_SCY_2 | \ |
| OR_GPCM_TRLX | OR_GPCM_EAD) |
| |
| /* |
| * PAXE on the local bus CS3 |
| */ |
| #define CONFIG_SYS_LBLAWBAR3_PRELIM CONFIG_SYS_PAXE_BASE /* Window base at flash base */ |
| #define CONFIG_SYS_LBLAWAR3_PRELIM 0x8000001C /* 512MB window size */ |
| |
| #define CONFIG_SYS_BR3_PRELIM (CONFIG_SYS_PAXE_BASE | \ |
| (1 << BR_PS_SHIFT) | /* 8 bit port size */ \ |
| BR_V) |
| #define CONFIG_SYS_OR3_PRELIM (MEG_TO_AM(CONFIG_SYS_PAXE_SIZE) | \ |
| OR_GPCM_CSNT | OR_GPCM_ACS_DIV2 | \ |
| OR_GPCM_SCY_2 | \ |
| OR_GPCM_TRLX | OR_GPCM_EAD) |
| |
| /* |
| * Serial Port |
| */ |
| #define CONFIG_CONS_INDEX 1 |
| #undef CONFIG_SERIAL_SOFTWARE_FIFO |
| #define CONFIG_SYS_NS16550 |
| #define CONFIG_SYS_NS16550_SERIAL |
| #define CONFIG_SYS_NS16550_REG_SIZE 1 |
| #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) |
| |
| #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500) |
| #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600) |
| |
| /* Pass open firmware flat tree */ |
| #define CONFIG_OF_LIBFDT 1 |
| #define CONFIG_OF_BOARD_SETUP 1 |
| #define CONFIG_OF_STDOUT_VIA_ALIAS |
| |
| /* |
| * General PCI |
| * Addresses are mapped 1-1. |
| */ |
| #undef CONFIG_PCI /* No PCI */ |
| |
| #ifndef CONFIG_NET_MULTI |
| #define CONFIG_NET_MULTI 1 |
| #endif |
| /* |
| * QE UEC ethernet configuration |
| */ |
| #define CONFIG_UEC_ETH |
| #define CONFIG_ETHPRIME "FSL UEC0" |
| |
| #define CONFIG_UEC_ETH1 /* GETH1 */ |
| #define UEC_VERBOSE_DEBUG 1 |
| |
| #ifdef CONFIG_UEC_ETH1 |
| #define CONFIG_SYS_UEC1_UCC_NUM 3 /* UCC4 */ |
| #define CONFIG_SYS_UEC1_RX_CLK QE_CLK_NONE /* not used in RMII Mode */ |
| #define CONFIG_SYS_UEC1_TX_CLK QE_CLK17 |
| #define CONFIG_SYS_UEC1_ETH_TYPE FAST_ETH |
| #define CONFIG_SYS_UEC1_PHY_ADDR 0 |
| #define CONFIG_SYS_UEC1_INTERFACE_MODE ENET_100_RMII |
| #endif |
| |
| /* |
| * Environment |
| */ |
| |
| #ifndef CONFIG_SYS_RAMBOOT |
| #define CONFIG_ENV_IS_IN_FLASH 1 |
| #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN) |
| #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */ |
| #define CONFIG_ENV_SIZE 0x20000 |
| #define CONFIG_ENV_OFFSET (CONFIG_SYS_MONITOR_LEN) |
| |
| /* Address and size of Redundant Environment Sector */ |
| #define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET+CONFIG_ENV_SECT_SIZE) |
| #define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) |
| |
| #else /* CFG_RAMBOOT */ |
| #define CONFIG_SYS_NO_FLASH 1 /* Flash is not usable now */ |
| #define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */ |
| #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) |
| #define CONFIG_ENV_SIZE 0x2000 |
| #endif /* CFG_RAMBOOT */ |
| |
| /* I2C */ |
| #define CONFIG_HARD_I2C /* I2C with hardware support */ |
| #undef CONFIG_SOFT_I2C /* I2C bit-banged */ |
| #define CONFIG_FSL_I2C |
| #define CONFIG_SYS_I2C_SPEED 200000 /* I2C speed and slave address */ |
| #define CONFIG_SYS_I2C_SLAVE 0x7F |
| #define CONFIG_SYS_I2C_OFFSET 0x3000 |
| #define CONFIG_I2C_MULTI_BUS 1 |
| #define CONFIG_I2C_CMD_TREE 1 |
| #define CONFIG_SYS_MAX_I2C_BUS 2 |
| #define CONFIG_I2C_MUX 1 |
| |
| /* EEprom support */ |
| #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 |
| #define CONFIG_SYS_I2C_MULTI_EEPROMS 1 |
| #define CONFIG_SYS_EEPROM_PAGE_WRITE_ENABLE |
| #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 |
| #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 |
| |
| /* Support the IVM EEprom */ |
| #define CONFIG_SYS_IVM_EEPROM_ADR 0x50 |
| #define CONFIG_SYS_IVM_EEPROM_MAX_LEN 0x400 |
| #define CONFIG_SYS_IVM_EEPROM_PAGE_LEN 0x100 |
| |
| /* I2C SYSMON (LM75, AD7414 is almost compatible) */ |
| #define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */ |
| #define CONFIG_DTT_SENSORS {0, 1, 2, 3} /* Sensor addresses */ |
| #define CONFIG_SYS_DTT_MAX_TEMP 70 |
| #define CONFIG_SYS_DTT_LOW_TEMP -30 |
| #define CONFIG_SYS_DTT_HYSTERESIS 3 |
| #define CONFIG_SYS_DTT_BUS_NUM (2) |
| |
| #if defined(CONFIG_PCI) |
| #define CONFIG_CMD_PCI |
| #endif |
| |
| #if defined(CFG_RAMBOOT) |
| #undef CONFIG_CMD_SAVEENV |
| #undef CONFIG_CMD_LOADS |
| #endif |
| |
| /* |
| * For booting Linux, the board info and command line data |
| * have to be in the first 8 MB of memory, since this is |
| * the maximum mapped by the Linux kernel during initialization. |
| */ |
| #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ |
| |
| /* |
| * Core HID Setup |
| */ |
| #define CONFIG_SYS_HID0_INIT 0x000000000 |
| #define CONFIG_SYS_HID0_FINAL HID0_ENABLE_MACHINE_CHECK |
| #define CONFIG_SYS_HID2 HID2_HBE |
| |
| /* |
| * MMU Setup |
| */ |
| |
| #define CONFIG_HIGH_BATS 1 /* High BATs supported */ |
| |
| /* DDR: cache cacheable */ |
| #define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_10 | \ |
| BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) |
| #define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP) |
| #define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L |
| #define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U |
| |
| /* IMMRBAR & PCI IO: cache-inhibit and guarded */ |
| #define CONFIG_SYS_IBAT1L (CONFIG_SYS_IMMR | BATL_PP_10 | \ |
| BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) |
| #define CONFIG_SYS_IBAT1U (CONFIG_SYS_IMMR | BATU_BL_4M | BATU_VS | BATU_VP) |
| #define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L |
| #define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U |
| |
| /* PRIO1, PIGGY: icache cacheable, but dcache-inhibit and guarded */ |
| #define CONFIG_SYS_IBAT2L (CONFIG_SYS_PIGGY_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) |
| #define CONFIG_SYS_IBAT2U (CONFIG_SYS_PIGGY_BASE | BATU_BL_128M | BATU_VS | BATU_VP) |
| #define CONFIG_SYS_DBAT2L (CONFIG_SYS_PIGGY_BASE | BATL_PP_10 | \ |
| BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) |
| #define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U |
| |
| /* FLASH: icache cacheable, but dcache-inhibit and guarded */ |
| #define CONFIG_SYS_IBAT3L (CONFIG_SYS_FLASH_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) |
| #define CONFIG_SYS_IBAT3U (CONFIG_SYS_FLASH_BASE | BATU_BL_256M | BATU_VS | BATU_VP) |
| #define CONFIG_SYS_DBAT3L (CONFIG_SYS_FLASH_BASE | BATL_PP_10 | \ |
| BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) |
| #define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U |
| |
| /* Stack in dcache: cacheable, no memory coherence */ |
| #define CONFIG_SYS_IBAT4L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_10) |
| #define CONFIG_SYS_IBAT4U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP) |
| #define CONFIG_SYS_DBAT4L CONFIG_SYS_IBAT4L |
| #define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U |
| |
| /* PAXE: icache cacheable, but dcache-inhibit and guarded */ |
| #define CONFIG_SYS_IBAT5L (CONFIG_SYS_PAXE_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) |
| #define CONFIG_SYS_IBAT5U (CONFIG_SYS_PAXE_BASE | BATU_BL_256M | BATU_VS | BATU_VP) |
| #define CONFIG_SYS_DBAT5L (CONFIG_SYS_PAXE_BASE | BATL_PP_10 | \ |
| BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) |
| #define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U |
| |
| #ifdef CONFIG_PCI |
| /* PCI MEM space: cacheable */ |
| #define CFG_IBAT6L (CFG_PCI1_MEM_PHYS | BATL_PP_10 | BATL_MEMCOHERENCE) |
| #define CFG_IBAT6U (CFG_PCI1_MEM_PHYS | BATU_BL_256M | BATU_VS | BATU_VP) |
| #define CFG_DBAT6L CFG_IBAT6L |
| #define CFG_DBAT6U CFG_IBAT6U |
| /* PCI MMIO space: cache-inhibit and guarded */ |
| #define CFG_IBAT7L (CFG_PCI1_MMIO_PHYS | BATL_PP_10 | \ |
| BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) |
| #define CFG_IBAT7U (CFG_PCI1_MMIO_PHYS | BATU_BL_256M | BATU_VS | BATU_VP) |
| #define CFG_DBAT7L CFG_IBAT7L |
| #define CFG_DBAT7U CFG_IBAT7U |
| #else /* CONFIG_PCI */ |
| #define CONFIG_SYS_IBAT6L (0) |
| #define CONFIG_SYS_IBAT6U (0) |
| #define CONFIG_SYS_IBAT7L (0) |
| #define CONFIG_SYS_IBAT7U (0) |
| #define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L |
| #define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U |
| #define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L |
| #define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U |
| #endif /* CONFIG_PCI */ |
| |
| /* |
| * Internal Definitions |
| * |
| * Boot Flags |
| */ |
| #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ |
| #define BOOTFLAG_WARM 0x02 /* Software reboot */ |
| |
| #define BOOTFLASH_START F0000000 |
| |
| #define CONFIG_PRAM 512 /* protected RAM [KBytes] */ |
| |
| #define MTDIDS_DEFAULT "nor0=app" |
| #define MTDPARTS_DEFAULT \ |
| "mtdparts=app:256k(u-boot),128k(env),128k(envred)," \ |
| "1536k(esw0),8704k(rootfs0),1536k(esw1),2432k(rootfs1),640k(var),768k(cfg)" |
| |
| /* |
| * Environment Configuration |
| */ |
| #define CONFIG_ENV_OVERWRITE |
| #ifndef CONFIG_KM_DEF_ENV /* if not set by keymile-common.h */ |
| #define CONFIG_KM_DEF_ENV "km-common=empty\0" |
| #endif |
| |
| #define CONFIG_EXTRA_ENV_SETTINGS \ |
| CONFIG_KM_DEF_ENV \ |
| "netdev=eth0\0" \ |
| "rootpath=/opt/eldk/ppc_82xx\0" \ |
| "nfsargs=setenv bootargs root=/dev/nfs rw " \ |
| "nfsroot=${serverip}:${rootpath}\0" \ |
| "ramargs=setenv bootargs root=/dev/ram rw\0" \ |
| "addip=setenv bootargs ${bootargs} " \ |
| "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ |
| ":${hostname}:${netdev}:off panic=1\0" \ |
| "addtty=setenv bootargs ${bootargs}" \ |
| " console=ttyS0,${baudrate}\0" \ |
| "fdt_addr=f0080000\0" \ |
| "kernel_addr=f00a0000\0" \ |
| "ramdisk_addr=f03a0000\0" \ |
| "kernel_addr_r=400000\0" \ |
| "fdt_addr_r=800000\0" \ |
| "ramdisk_addr_r=810000\0" \ |
| "flash_self=run ramargs addip addtty;" \ |
| "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \ |
| "flash_nfs=run nfsargs addip addtty;" \ |
| "bootm ${kernel_addr} - ${fdt_addr}\0" \ |
| "net_nfs=tftp ${kernel_addr_r} ${boot_file}; " \ |
| "tftp ${fdt_addr_r} ${fdt_file}; " \ |
| "run nfsargs addip addtty;" \ |
| "bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \ |
| "fdt_file=/tftpboot/kmeter1/kmeter1.dtb\0" \ |
| "boot_file=/tftpboot/kmeter1/uImage\0" \ |
| "ramdisk_file=/tftpboot/kmeter1/uRamdisk\0" \ |
| "u-boot=/tftpboot/kmeter1/u-boot.bin\0" \ |
| "loadaddr=" MK_STR(CONFIG_SYS_LOAD_ADDR) "\0" \ |
| "load=tftp $loadaddr ${u-boot}\0" \ |
| "update=protect off " MK_STR(TEXT_BASE) " +$filesize;" \ |
| "erase " MK_STR(TEXT_BASE) " +$filesize;" \ |
| "cp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize;" \ |
| "protect on " MK_STR(TEXT_BASE) " +$filesize;" \ |
| "cmp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize;" \ |
| "setenv filesize;saveenv\0" \ |
| "upd=run load update\0" \ |
| "loadram=tftp ${ramdisk_addr_r} ${ramdisk_file}\0" \ |
| "loadfdt=tftp ${fdt_addr_r} ${fdt_file}\0" \ |
| "loadkernel=tftp ${kernel_addr_r} ${boot_file}\0" \ |
| "unlock=yes\0" \ |
| "EEprom_ivm=pca9547:70:9\0" \ |
| "dtt_bus=pca9547:70:a\0" \ |
| "mtdids=nor0=app \0" \ |
| "mtdparts=" MK_STR(MTDPARTS_DEFAULT) "\0" \ |
| "" |
| |
| #if defined(CONFIG_UEC_ETH) |
| #define CONFIG_HAS_ETH0 |
| #endif |
| |
| #endif /* __CONFIG_H */ |