board/birdland/bav335x/board.c - filogic/uboot - Gitiles

 // SPDX-License-Identifier: GPL-2.0+
 /*
  * board.c
  *
  * Board functions for Birdland Audio BAV335x Network Processor
  *
  * Copyright (c) 2012-2014 Birdland Audio - http://birdland.com/oem
  */

 #include <common.h>
 #include <env.h>
 #include <errno.h>
 #include <init.h>
 #include <serial.h>
 #include <spl.h>
 #include <asm/arch/cpu.h>
 #include <asm/arch/hardware.h>
 #include <asm/arch/omap.h>
 #include <asm/arch/ddr_defs.h>
 #include <asm/arch/clock.h>
 #include <asm/arch/gpio.h>
 #include <asm/arch/mmc_host_def.h>
 #include <asm/arch/sys_proto.h>
 #include <asm/arch/mem.h>
 #include <asm/io.h>
 #include <asm/emif.h>
 #include <asm/gpio.h>
 #include <i2c.h>
 #include <miiphy.h>
 #include <cpsw.h>
 #include <power/tps65217.h>
 #include <power/tps65910.h>
 #include <env_internal.h>
 #include <watchdog.h>
 #include "board.h"

 DECLARE_GLOBAL_DATA_PTR;

 /* GPIO that controls power to DDR on EVM-SK */
 #define GPIO_DDR_VTT_EN		7

 static __maybe_unused struct ctrl_dev *cdev =
 		(struct ctrl_dev *)CTRL_DEVICE_BASE;


 /*
  * Read header information from EEPROM into global structure.
  */
 static int read_eeprom(struct board_eeconfig *header)
 {
 	/* Check if baseboard eeprom is available */
 	if (i2c_probe(CONFIG_SYS_I2C_EEPROM_ADDR))
 		return -ENODEV;

 	/* read the eeprom using i2c */
 	if (i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0, 2, (uchar *)header,
 		     sizeof(struct board_eeconfig)))
 		return -EIO;

 	if (header->magic != BOARD_MAGIC) {
 		/* read the i2c eeprom again using only a 1 byte address */
 		if (i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0, 1, (uchar *)header,
 			     sizeof(struct board_eeconfig)))
 			return -EIO;

 		if (header->magic != BOARD_MAGIC)
 			return -EINVAL;
 	}
 	return 0;
 }


 enum board_type get_board_type(bool debug)
 {
 	int ecode;
 	struct board_eeconfig header;

 	ecode = read_eeprom(&header);
 	if (ecode == 0) {
 		if (header.version[1] == 'A') {
 			if (debug)
 				puts("=== Detected Board model BAV335x Rev.A");
 			return BAV335A;
 		} else if (header.version[1] == 'B') {
 			if (debug)
 				puts("=== Detected Board model BAV335x Rev.B");
 			return BAV335B;
 		} else if (debug) {
 			puts("### Un-known board model in serial-EE\n");
 		}
 	} else if (debug) {
 		switch (ecode) {
 		case -ENODEV:
 			puts("### Board doesn't have a serial-EE\n");
 			break;
 		case -EINVAL:
 			puts("### Board serial-EE signature is incorrect.\n");
 			break;
 		default:
 			puts("### IO Error reading serial-EE.\n");
 			break;
 		}
 	}

 #if (CONFIG_BAV_VERSION == 1)
 	if (debug)
 		puts("### Selecting BAV335A as per config\n");
 	return BAV335A;
 #elif (CONFIG_BAV_VERSION == 2)
 	if (debug)
 		puts("### Selecting BAV335B as per config\n");
 	return BAV335B;
 #endif
 #if (NOT_DEFINED == 2)
 #error "SHOULD NEVER DISPLAY THIS"
 #endif

 	if (debug)
 		puts("### Defaulting to model BAV335x Rev.B\n");
 	return BAV335B;
 }


 #ifndef CONFIG_SKIP_LOWLEVEL_INIT
 static const struct ddr_data ddr3_bav335x_data = {
 	.datardsratio0 = MT41K256M16HA125E_RD_DQS,
 	.datawdsratio0 = MT41K256M16HA125E_WR_DQS,
 	.datafwsratio0 = MT41K256M16HA125E_PHY_FIFO_WE,
 	.datawrsratio0 = MT41K256M16HA125E_PHY_WR_DATA,
 };

 static const struct cmd_control ddr3_bav335x_cmd_ctrl_data = {
 	.cmd0csratio = MT41K256M16HA125E_RATIO,
 	.cmd0iclkout = MT41K256M16HA125E_INVERT_CLKOUT,
 	.cmd1csratio = MT41K256M16HA125E_RATIO,
 	.cmd1iclkout = MT41K256M16HA125E_INVERT_CLKOUT,
 	.cmd2csratio = MT41K256M16HA125E_RATIO,
 	.cmd2iclkout = MT41K256M16HA125E_INVERT_CLKOUT,
 };


 static struct emif_regs ddr3_bav335x_emif_reg_data = {
 	.sdram_config = MT41K256M16HA125E_EMIF_SDCFG,
 	.ref_ctrl = MT41K256M16HA125E_EMIF_SDREF,
 	.sdram_tim1 = MT41K256M16HA125E_EMIF_TIM1,
 	.sdram_tim2 = MT41K256M16HA125E_EMIF_TIM2,
 	.sdram_tim3 = MT41K256M16HA125E_EMIF_TIM3,
 	.zq_config = MT41K256M16HA125E_ZQ_CFG,
 	.emif_ddr_phy_ctlr_1 = MT41K256M16HA125E_EMIF_READ_LATENCY,
 };


 #ifdef CONFIG_SPL_OS_BOOT
 int spl_start_uboot(void)
 {
 	/* break into full u-boot on 'c' */
 	if (serial_tstc() && serial_getc() == 'c')
 		return 1;

 #ifdef CONFIG_SPL_ENV_SUPPORT
 	env_init();
 	env_load();
 	if (env_get_yesno("boot_os") != 1)
 		return 1;
 #endif

 	return 0;
 }
 #endif

 #define OSC	(V_OSCK/1000000)
 const struct dpll_params dpll_ddr = {
 		266, OSC-1, 1, -1, -1, -1, -1};
 const struct dpll_params dpll_ddr_evm_sk = {
 		303, OSC-1, 1, -1, -1, -1, -1};
 const struct dpll_params dpll_ddr_bone_black = {
 		400, OSC-1, 1, -1, -1, -1, -1};

 void am33xx_spl_board_init(void)
 {
 	/* debug print detect status */
 	(void)get_board_type(true);

 	/* Get the frequency */
 	/* dpll_mpu_opp100.m = am335x_get_efuse_mpu_max_freq(cdev); */
 	dpll_mpu_opp100.m = MPUPLL_M_1000;

 	if (i2c_probe(TPS65217_CHIP_PM))
 		return;

 	/* Set the USB Current Limit */
 	if (tps65217_reg_write(TPS65217_PROT_LEVEL_NONE, TPS65217_POWER_PATH,
 			       TPS65217_USB_INPUT_CUR_LIMIT_1800MA,
 			       TPS65217_USB_INPUT_CUR_LIMIT_MASK))
 		puts("! tps65217_reg_write: could not set USB limit\n");

 	/* Set the Core Voltage (DCDC3) to 1.125V */
 	if (tps65217_voltage_update(TPS65217_DEFDCDC3,
 				    TPS65217_DCDC_VOLT_SEL_1125MV)) {
 		puts("! tps65217_reg_write: could not set Core Voltage\n");
 		return;
 	}

 	/* Set CORE Frequencies to OPP100 */
 	do_setup_dpll(&dpll_core_regs, &dpll_core_opp100);

 	/* Set the MPU Voltage (DCDC2) */
 	if (tps65217_voltage_update(TPS65217_DEFDCDC2,
 				    TPS65217_DCDC_VOLT_SEL_1325MV)) {
 		puts("! tps65217_reg_write: could not set MPU Voltage\n");
 		return;
 	}

 	/*
 	 * Set LDO3, LDO4 output voltage to 3.3V for Beaglebone.
 	 * Set LDO3 to 1.8V and LDO4 to 3.3V for Beaglebone Black.
 	 */
 	if (tps65217_reg_write(TPS65217_PROT_LEVEL_2, TPS65217_DEFLS1,
 			       TPS65217_LDO_VOLTAGE_OUT_1_8, TPS65217_LDO_MASK))
 		puts("! tps65217_reg_write: could not set LDO3\n");

 	if (tps65217_reg_write(TPS65217_PROT_LEVEL_2, TPS65217_DEFLS2,
 			       TPS65217_LDO_VOLTAGE_OUT_3_3, TPS65217_LDO_MASK))
 		puts("! tps65217_reg_write: could not set LDO4\n");

 	/* Set MPU Frequency to what we detected now that voltages are set */
 	do_setup_dpll(&dpll_mpu_regs, &dpll_mpu_opp100);
 }

 const struct dpll_params *get_dpll_ddr_params(void)
 {
 	enable_i2c0_pin_mux();
 	i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE);

 	return &dpll_ddr_bone_black;
 }

 void set_uart_mux_conf(void)
 {
 #if CONFIG_CONS_INDEX == 1
 	enable_uart0_pin_mux();
 #elif CONFIG_CONS_INDEX == 2
 	enable_uart1_pin_mux();
 #elif CONFIG_CONS_INDEX == 3
 	enable_uart2_pin_mux();
 #elif CONFIG_CONS_INDEX == 4
 	enable_uart3_pin_mux();
 #elif CONFIG_CONS_INDEX == 5
 	enable_uart4_pin_mux();
 #elif CONFIG_CONS_INDEX == 6
 	enable_uart5_pin_mux();
 #endif
 }

 void set_mux_conf_regs(void)
 {
 	enum board_type board;

 	board = get_board_type(false);
 	enable_board_pin_mux(board);
 }

 const struct ctrl_ioregs ioregs_bonelt = {
 	.cm0ioctl		= MT41K256M16HA125E_IOCTRL_VALUE,
 	.cm1ioctl		= MT41K256M16HA125E_IOCTRL_VALUE,
 	.cm2ioctl		= MT41K256M16HA125E_IOCTRL_VALUE,
 	.dt0ioctl		= MT41K256M16HA125E_IOCTRL_VALUE,
 	.dt1ioctl		= MT41K256M16HA125E_IOCTRL_VALUE,
 };


 void sdram_init(void)
 {
 	config_ddr(400, &ioregs_bonelt,
 		   &ddr3_bav335x_data,
 		   &ddr3_bav335x_cmd_ctrl_data,
 		   &ddr3_bav335x_emif_reg_data, 0);
 }
 #endif

 /*
  * Basic board specific setup.  Pinmux has been handled already.
  */
 int board_init(void)
 {
 #if defined(CONFIG_HW_WATCHDOG)
 	hw_watchdog_init();
 #endif

 	gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
 #if defined(CONFIG_NOR) || defined(CONFIG_NAND)
 	gpmc_init();
 #endif
 	return 0;
 }

 #ifdef CONFIG_BOARD_LATE_INIT
 int board_late_init(void)
 {
 #ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
 	env_set("board_name", "BAV335xB");
 	env_set("board_rev", "B"); /* Fix me, but why bother.. */
 #endif
 	return 0;
 }
 #endif


 #if (defined(CONFIG_DRIVER_TI_CPSW) && !defined(CONFIG_SPL_BUILD)) || \
 	(defined(CONFIG_SPL_ETH_SUPPORT) && defined(CONFIG_SPL_BUILD))
 static void cpsw_control(int enabled)
 {
 	/* VTP can be added here */
 	return;
 }

 static struct cpsw_slave_data cpsw_slaves[] = {
 	{
 		.slave_reg_ofs	= 0x208,
 		.sliver_reg_ofs	= 0xd80,
 		.phy_addr	= 0,
 	},
 	{
 		.slave_reg_ofs	= 0x308,
 		.sliver_reg_ofs	= 0xdc0,
 		.phy_addr	= 1,
 	},
 };

 static struct cpsw_platform_data cpsw_data = {
 	.mdio_base		= CPSW_MDIO_BASE,
 	.cpsw_base		= CPSW_BASE,
 	.mdio_div		= 0xff,
 	.channels		= 8,
 	.cpdma_reg_ofs	= 0x800,
 	.slaves			= 1,
 	.slave_data		= cpsw_slaves,
 	.ale_reg_ofs	= 0xd00,
 	.ale_entries	= 1024,
 	.host_port_reg_ofs	= 0x108,
 	.hw_stats_reg_ofs	= 0x900,
 	.bd_ram_ofs		= 0x2000,
 	.mac_control	= (1 << 5),
 	.control		= cpsw_control,
 	.host_port_num	= 0,
 	.version		= CPSW_CTRL_VERSION_2,
 };
 #endif


 /*
  * This function will:
  * Perform fixups to the PHY present on certain boards.  We only need this
  * function in:
  * - SPL with either CPSW or USB ethernet support
  * - Full U-Boot, with either CPSW or USB ethernet
  * Build in only these cases to avoid warnings about unused variables
  * when we build an SPL that has neither option but full U-Boot will.
  */
 #if ((defined(CONFIG_SPL_ETH_SUPPORT) || defined(CONFIG_SPL_USB_ETHER)) &&\
 		defined(CONFIG_SPL_BUILD)) || \
 	((defined(CONFIG_DRIVER_TI_CPSW) || \
 	  defined(CONFIG_USB_ETHER) && defined(CONFIG_USB_MUSB_GADGET)) && \
 	 !defined(CONFIG_SPL_BUILD))
 int board_eth_init(bd_t *bis)
 {
 	int ecode, rv, n;
 	uint8_t mac_addr[6];
 	struct board_eeconfig header;
 	__maybe_unused enum board_type board;

 	/* Default manufacturing address; used when no EE or invalid */
 	n = 0;
 	mac_addr[0] = 0;
 	mac_addr[1] = 0x20;
 	mac_addr[2] = 0x18;
 	mac_addr[3] = 0x1C;
 	mac_addr[4] = 0x00;
 	mac_addr[5] = 0x01;

 	ecode = read_eeprom(&header);
 	/* if we have a valid EE, get mac address from there */
 	if ((ecode == 0) &&
 	    is_valid_ethaddr((const u8 *)&header.mac_addr[0][0])) {
 		memcpy(mac_addr, (const void *)&header.mac_addr[0][0], 6);
 	}


 #if (defined(CONFIG_DRIVER_TI_CPSW) && !defined(CONFIG_SPL_BUILD)) || \
 	(defined(CONFIG_SPL_ETH_SUPPORT) && defined(CONFIG_SPL_BUILD))

 	if (!env_get("ethaddr")) {
 		printf("<ethaddr> not set. Validating first E-fuse MAC\n");

 		if (is_valid_ethaddr(mac_addr))
 			eth_env_set_enetaddr("ethaddr", mac_addr);
 	}

 #ifdef CONFIG_DRIVER_TI_CPSW

 	board = get_board_type(false);

 	/* Rev.A uses 10/100 PHY in mii mode */
 	if (board == BAV335A) {
 		writel(MII_MODE_ENABLE, &cdev->miisel);
 		cpsw_slaves[0].phy_if = PHY_INTERFACE_MODE_MII;
 		cpsw_slaves[1].phy_if = PHY_INTERFACE_MODE_MII;
 	}
 	/* Rev.B (default) uses GB PHY in rmii mode */
 	else {
 		writel((RGMII_MODE_ENABLE | RGMII_INT_DELAY), &cdev->miisel);
 		cpsw_slaves[0].phy_if = cpsw_slaves[1].phy_if
 				= PHY_INTERFACE_MODE_RGMII;
 	}

 	rv = cpsw_register(&cpsw_data);
 	if (rv < 0)
 		printf("Error %d registering CPSW switch\n", rv);
 	else
 		n += rv;
 #endif

 #endif

 	return n;
 }
 #endif
	// SPDX-License-Identifier: GPL-2.0+
	/*
	* board.c
	*
	* Board functions for Birdland Audio BAV335x Network Processor
	*
	* Copyright (c) 2012-2014 Birdland Audio - http://birdland.com/oem
	*/

	#include <common.h>
	#include <env.h>
	#include <errno.h>
	#include <init.h>
	#include <serial.h>
	#include <spl.h>
	#include <asm/arch/cpu.h>
	#include <asm/arch/hardware.h>
	#include <asm/arch/omap.h>
	#include <asm/arch/ddr_defs.h>
	#include <asm/arch/clock.h>
	#include <asm/arch/gpio.h>
	#include <asm/arch/mmc_host_def.h>
	#include <asm/arch/sys_proto.h>
	#include <asm/arch/mem.h>
	#include <asm/io.h>
	#include <asm/emif.h>
	#include <asm/gpio.h>
	#include <i2c.h>
	#include <miiphy.h>
	#include <cpsw.h>
	#include <power/tps65217.h>
	#include <power/tps65910.h>
	#include <env_internal.h>
	#include <watchdog.h>
	#include "board.h"

	DECLARE_GLOBAL_DATA_PTR;

	/* GPIO that controls power to DDR on EVM-SK */
	#define GPIO_DDR_VTT_EN 7

	static __maybe_unused struct ctrl_dev *cdev =
	(struct ctrl_dev *)CTRL_DEVICE_BASE;



	/*
	* Read header information from EEPROM into global structure.
	*/
	static int read_eeprom(struct board_eeconfig *header)
	{
	/* Check if baseboard eeprom is available */
	if (i2c_probe(CONFIG_SYS_I2C_EEPROM_ADDR))
	return -ENODEV;

	/* read the eeprom using i2c */
	if (i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0, 2, (uchar *)header,
	sizeof(struct board_eeconfig)))
	return -EIO;

	if (header->magic != BOARD_MAGIC) {
	/* read the i2c eeprom again using only a 1 byte address */
	if (i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0, 1, (uchar *)header,
	sizeof(struct board_eeconfig)))
	return -EIO;

	if (header->magic != BOARD_MAGIC)
	return -EINVAL;
	}
	return 0;
	}




	enum board_type get_board_type(bool debug)
	{
	int ecode;
	struct board_eeconfig header;

	ecode = read_eeprom(&header);
	if (ecode == 0) {
	if (header.version[1] == 'A') {
	if (debug)
	puts("=== Detected Board model BAV335x Rev.A");
	return BAV335A;
	} else if (header.version[1] == 'B') {
	if (debug)
	puts("=== Detected Board model BAV335x Rev.B");
	return BAV335B;
	} else if (debug) {
	puts("### Un-known board model in serial-EE\n");
	}
	} else if (debug) {
	switch (ecode) {
	case -ENODEV:
	puts("### Board doesn't have a serial-EE\n");
	break;
	case -EINVAL:
	puts("### Board serial-EE signature is incorrect.\n");
	break;
	default:
	puts("### IO Error reading serial-EE.\n");
	break;
	}
	}

	#if (CONFIG_BAV_VERSION == 1)
	if (debug)
	puts("### Selecting BAV335A as per config\n");
	return BAV335A;
	#elif (CONFIG_BAV_VERSION == 2)
	if (debug)
	puts("### Selecting BAV335B as per config\n");
	return BAV335B;
	#endif
	#if (NOT_DEFINED == 2)
	#error "SHOULD NEVER DISPLAY THIS"
	#endif

	if (debug)
	puts("### Defaulting to model BAV335x Rev.B\n");
	return BAV335B;
	}



	#ifndef CONFIG_SKIP_LOWLEVEL_INIT
	static const struct ddr_data ddr3_bav335x_data = {
	.datardsratio0 = MT41K256M16HA125E_RD_DQS,
	.datawdsratio0 = MT41K256M16HA125E_WR_DQS,
	.datafwsratio0 = MT41K256M16HA125E_PHY_FIFO_WE,
	.datawrsratio0 = MT41K256M16HA125E_PHY_WR_DATA,
	};

	static const struct cmd_control ddr3_bav335x_cmd_ctrl_data = {
	.cmd0csratio = MT41K256M16HA125E_RATIO,
	.cmd0iclkout = MT41K256M16HA125E_INVERT_CLKOUT,
	.cmd1csratio = MT41K256M16HA125E_RATIO,
	.cmd1iclkout = MT41K256M16HA125E_INVERT_CLKOUT,
	.cmd2csratio = MT41K256M16HA125E_RATIO,
	.cmd2iclkout = MT41K256M16HA125E_INVERT_CLKOUT,
	};


	static struct emif_regs ddr3_bav335x_emif_reg_data = {
	.sdram_config = MT41K256M16HA125E_EMIF_SDCFG,
	.ref_ctrl = MT41K256M16HA125E_EMIF_SDREF,
	.sdram_tim1 = MT41K256M16HA125E_EMIF_TIM1,
	.sdram_tim2 = MT41K256M16HA125E_EMIF_TIM2,
	.sdram_tim3 = MT41K256M16HA125E_EMIF_TIM3,
	.zq_config = MT41K256M16HA125E_ZQ_CFG,
	.emif_ddr_phy_ctlr_1 = MT41K256M16HA125E_EMIF_READ_LATENCY,
	};


	#ifdef CONFIG_SPL_OS_BOOT
	int spl_start_uboot(void)
	{
	/* break into full u-boot on 'c' */
	if (serial_tstc() && serial_getc() == 'c')
	return 1;

	#ifdef CONFIG_SPL_ENV_SUPPORT
	env_init();
	env_load();
	if (env_get_yesno("boot_os") != 1)
	return 1;
	#endif

	return 0;
	}
	#endif

	#define OSC (V_OSCK/1000000)
	const struct dpll_params dpll_ddr = {
	266, OSC-1, 1, -1, -1, -1, -1};
	const struct dpll_params dpll_ddr_evm_sk = {
	303, OSC-1, 1, -1, -1, -1, -1};
	const struct dpll_params dpll_ddr_bone_black = {
	400, OSC-1, 1, -1, -1, -1, -1};

	void am33xx_spl_board_init(void)
	{
	/* debug print detect status */
	(void)get_board_type(true);

	/* Get the frequency */
	/* dpll_mpu_opp100.m = am335x_get_efuse_mpu_max_freq(cdev); */
	dpll_mpu_opp100.m = MPUPLL_M_1000;

	if (i2c_probe(TPS65217_CHIP_PM))
	return;

	/* Set the USB Current Limit */
	if (tps65217_reg_write(TPS65217_PROT_LEVEL_NONE, TPS65217_POWER_PATH,
	TPS65217_USB_INPUT_CUR_LIMIT_1800MA,
	TPS65217_USB_INPUT_CUR_LIMIT_MASK))
	puts("! tps65217_reg_write: could not set USB limit\n");

	/* Set the Core Voltage (DCDC3) to 1.125V */
	if (tps65217_voltage_update(TPS65217_DEFDCDC3,
	TPS65217_DCDC_VOLT_SEL_1125MV)) {
	puts("! tps65217_reg_write: could not set Core Voltage\n");
	return;
	}

	/* Set CORE Frequencies to OPP100 */
	do_setup_dpll(&dpll_core_regs, &dpll_core_opp100);

	/* Set the MPU Voltage (DCDC2) */
	if (tps65217_voltage_update(TPS65217_DEFDCDC2,
	TPS65217_DCDC_VOLT_SEL_1325MV)) {
	puts("! tps65217_reg_write: could not set MPU Voltage\n");
	return;
	}

	/*
	* Set LDO3, LDO4 output voltage to 3.3V for Beaglebone.
	* Set LDO3 to 1.8V and LDO4 to 3.3V for Beaglebone Black.
	*/
	if (tps65217_reg_write(TPS65217_PROT_LEVEL_2, TPS65217_DEFLS1,
	TPS65217_LDO_VOLTAGE_OUT_1_8, TPS65217_LDO_MASK))
	puts("! tps65217_reg_write: could not set LDO3\n");

	if (tps65217_reg_write(TPS65217_PROT_LEVEL_2, TPS65217_DEFLS2,
	TPS65217_LDO_VOLTAGE_OUT_3_3, TPS65217_LDO_MASK))
	puts("! tps65217_reg_write: could not set LDO4\n");

	/* Set MPU Frequency to what we detected now that voltages are set */
	do_setup_dpll(&dpll_mpu_regs, &dpll_mpu_opp100);
	}

	const struct dpll_params *get_dpll_ddr_params(void)
	{
	enable_i2c0_pin_mux();
	i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE);

	return &dpll_ddr_bone_black;
	}

	void set_uart_mux_conf(void)
	{
	#if CONFIG_CONS_INDEX == 1
	enable_uart0_pin_mux();
	#elif CONFIG_CONS_INDEX == 2
	enable_uart1_pin_mux();
	#elif CONFIG_CONS_INDEX == 3
	enable_uart2_pin_mux();
	#elif CONFIG_CONS_INDEX == 4
	enable_uart3_pin_mux();
	#elif CONFIG_CONS_INDEX == 5
	enable_uart4_pin_mux();
	#elif CONFIG_CONS_INDEX == 6
	enable_uart5_pin_mux();
	#endif
	}

	void set_mux_conf_regs(void)
	{
	enum board_type board;

	board = get_board_type(false);
	enable_board_pin_mux(board);
	}

	const struct ctrl_ioregs ioregs_bonelt = {
	.cm0ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
	.cm1ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
	.cm2ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
	.dt0ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
	.dt1ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
	};


	void sdram_init(void)
	{
	config_ddr(400, &ioregs_bonelt,
	&ddr3_bav335x_data,
	&ddr3_bav335x_cmd_ctrl_data,
	&ddr3_bav335x_emif_reg_data, 0);
	}
	#endif

	/*
	* Basic board specific setup. Pinmux has been handled already.
	*/
	int board_init(void)
	{
	#if defined(CONFIG_HW_WATCHDOG)
	hw_watchdog_init();
	#endif

	gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
	#if defined(CONFIG_NOR) \|\| defined(CONFIG_NAND)
	gpmc_init();
	#endif
	return 0;
	}

	#ifdef CONFIG_BOARD_LATE_INIT
	int board_late_init(void)
	{
	#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
	env_set("board_name", "BAV335xB");
	env_set("board_rev", "B"); /* Fix me, but why bother.. */
	#endif
	return 0;
	}
	#endif


	#if (defined(CONFIG_DRIVER_TI_CPSW) && !defined(CONFIG_SPL_BUILD)) \|\| \
	(defined(CONFIG_SPL_ETH_SUPPORT) && defined(CONFIG_SPL_BUILD))
	static void cpsw_control(int enabled)
	{
	/* VTP can be added here */
	return;
	}

	static struct cpsw_slave_data cpsw_slaves[] = {
	{
	.slave_reg_ofs = 0x208,
	.sliver_reg_ofs = 0xd80,
	.phy_addr = 0,
	},
	{
	.slave_reg_ofs = 0x308,
	.sliver_reg_ofs = 0xdc0,
	.phy_addr = 1,
	},
	};

	static struct cpsw_platform_data cpsw_data = {
	.mdio_base = CPSW_MDIO_BASE,
	.cpsw_base = CPSW_BASE,
	.mdio_div = 0xff,
	.channels = 8,
	.cpdma_reg_ofs = 0x800,
	.slaves = 1,
	.slave_data = cpsw_slaves,
	.ale_reg_ofs = 0xd00,
	.ale_entries = 1024,
	.host_port_reg_ofs = 0x108,
	.hw_stats_reg_ofs = 0x900,
	.bd_ram_ofs = 0x2000,
	.mac_control = (1 << 5),
	.control = cpsw_control,
	.host_port_num = 0,
	.version = CPSW_CTRL_VERSION_2,
	};
	#endif


	/*
	* This function will:
	* Perform fixups to the PHY present on certain boards. We only need this
	* function in:
	* - SPL with either CPSW or USB ethernet support
	* - Full U-Boot, with either CPSW or USB ethernet
	* Build in only these cases to avoid warnings about unused variables
	* when we build an SPL that has neither option but full U-Boot will.
	*/
	#if ((defined(CONFIG_SPL_ETH_SUPPORT) \|\| defined(CONFIG_SPL_USB_ETHER)) &&\
	defined(CONFIG_SPL_BUILD)) \|\| \
	((defined(CONFIG_DRIVER_TI_CPSW) \|\| \
	defined(CONFIG_USB_ETHER) && defined(CONFIG_USB_MUSB_GADGET)) && \
	!defined(CONFIG_SPL_BUILD))
	int board_eth_init(bd_t *bis)
	{
	int ecode, rv, n;
	uint8_t mac_addr[6];
	struct board_eeconfig header;
	__maybe_unused enum board_type board;

	/* Default manufacturing address; used when no EE or invalid */
	n = 0;
	mac_addr[0] = 0;
	mac_addr[1] = 0x20;
	mac_addr[2] = 0x18;
	mac_addr[3] = 0x1C;
	mac_addr[4] = 0x00;
	mac_addr[5] = 0x01;

	ecode = read_eeprom(&header);
	/* if we have a valid EE, get mac address from there */
	if ((ecode == 0) &&
	is_valid_ethaddr((const u8 *)&header.mac_addr[0][0])) {
	memcpy(mac_addr, (const void *)&header.mac_addr[0][0], 6);
	}


	#if (defined(CONFIG_DRIVER_TI_CPSW) && !defined(CONFIG_SPL_BUILD)) \|\| \
	(defined(CONFIG_SPL_ETH_SUPPORT) && defined(CONFIG_SPL_BUILD))

	if (!env_get("ethaddr")) {
	printf("<ethaddr> not set. Validating first E-fuse MAC\n");

	if (is_valid_ethaddr(mac_addr))
	eth_env_set_enetaddr("ethaddr", mac_addr);
	}

	#ifdef CONFIG_DRIVER_TI_CPSW

	board = get_board_type(false);

	/* Rev.A uses 10/100 PHY in mii mode */
	if (board == BAV335A) {
	writel(MII_MODE_ENABLE, &cdev->miisel);
	cpsw_slaves[0].phy_if = PHY_INTERFACE_MODE_MII;
	cpsw_slaves[1].phy_if = PHY_INTERFACE_MODE_MII;
	}
	/* Rev.B (default) uses GB PHY in rmii mode */
	else {
	writel((RGMII_MODE_ENABLE \| RGMII_INT_DELAY), &cdev->miisel);
	cpsw_slaves[0].phy_if = cpsw_slaves[1].phy_if
	= PHY_INTERFACE_MODE_RGMII;
	}

	rv = cpsw_register(&cpsw_data);
	if (rv < 0)
	printf("Error %d registering CPSW switch\n", rv);
	else
	n += rv;
	#endif

	#endif

	return n;
	}
	#endif