| // SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause |
| /* |
| * Copyright : STMicroelectronics 2018 |
| */ |
| |
| #include <dt-bindings/clock/stm32mp1-clksrc.h> |
| #include <dt-bindings/input/linux-event-codes.h> |
| #include "stm32mp15-u-boot.dtsi" |
| #include "stm32mp15-ddr3-2x4Gb-1066-binG.dtsi" |
| |
| / { |
| aliases { |
| i2c3 = &i2c4; |
| }; |
| |
| config { |
| u-boot,boot-led = "led-blue"; |
| u-boot,error-led = "led-red"; |
| u-boot,mmc-env-partition = "fip"; |
| }; |
| |
| #if defined(CONFIG_STM32MP15X_STM32IMAGE) || defined(CONFIG_SPL) |
| config { |
| u-boot,mmc-env-partition = "ssbl"; |
| }; |
| #endif |
| |
| #ifdef CONFIG_STM32MP15X_STM32IMAGE |
| /* only needed for boot with TF-A, witout FIP support */ |
| firmware { |
| optee { |
| compatible = "linaro,optee-tz"; |
| method = "smc"; |
| }; |
| }; |
| |
| reserved-memory { |
| optee@fe000000 { |
| reg = <0xfe000000 0x02000000>; |
| no-map; |
| }; |
| }; |
| #endif |
| |
| gpio-keys { |
| compatible = "gpio-keys"; |
| |
| button-user-1 { |
| label = "User-1"; |
| linux,code = <BTN_1>; |
| gpios = <&gpioa 14 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; |
| }; |
| |
| button-user-2 { |
| label = "User-2"; |
| linux,code = <BTN_2>; |
| gpios = <&gpioa 13 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; |
| }; |
| }; |
| |
| led { |
| compatible = "gpio-leds"; |
| |
| led-blue { |
| gpios = <&gpiod 9 GPIO_ACTIVE_HIGH>; |
| }; |
| |
| led-red { |
| gpios = <&gpioa 13 GPIO_ACTIVE_LOW>; |
| }; |
| }; |
| }; |
| |
| &clk_hse { |
| st,digbypass; |
| }; |
| |
| &i2c4 { |
| bootph-all; |
| }; |
| |
| &i2c4_pins_a { |
| bootph-all; |
| pins { |
| bootph-all; |
| }; |
| }; |
| |
| &pmic { |
| bootph-all; |
| }; |
| |
| &rcc { |
| st,clksrc = < |
| CLK_MPU_PLL1P |
| CLK_AXI_PLL2P |
| CLK_MCU_PLL3P |
| CLK_PLL12_HSE |
| CLK_PLL3_HSE |
| CLK_PLL4_HSE |
| CLK_RTC_LSE |
| CLK_MCO1_DISABLED |
| CLK_MCO2_DISABLED |
| >; |
| |
| st,clkdiv = < |
| 1 /*MPU*/ |
| 0 /*AXI*/ |
| 0 /*MCU*/ |
| 1 /*APB1*/ |
| 1 /*APB2*/ |
| 1 /*APB3*/ |
| 1 /*APB4*/ |
| 2 /*APB5*/ |
| 23 /*RTC*/ |
| 0 /*MCO1*/ |
| 0 /*MCO2*/ |
| >; |
| |
| st,pkcs = < |
| CLK_CKPER_HSE |
| CLK_FMC_ACLK |
| CLK_QSPI_ACLK |
| CLK_ETH_DISABLED |
| CLK_SDMMC12_PLL4P |
| CLK_DSI_DSIPLL |
| CLK_STGEN_HSE |
| CLK_USBPHY_HSE |
| CLK_SPI2S1_PLL3Q |
| CLK_SPI2S23_PLL3Q |
| CLK_SPI45_HSI |
| CLK_SPI6_HSI |
| CLK_I2C46_HSI |
| CLK_SDMMC3_PLL4P |
| CLK_USBO_USBPHY |
| CLK_ADC_CKPER |
| CLK_CEC_LSE |
| CLK_I2C12_HSI |
| CLK_I2C35_HSI |
| CLK_UART1_HSI |
| CLK_UART24_HSI |
| CLK_UART35_HSI |
| CLK_UART6_HSI |
| CLK_UART78_HSI |
| CLK_SPDIF_PLL4P |
| CLK_FDCAN_PLL4R |
| CLK_SAI1_PLL3Q |
| CLK_SAI2_PLL3Q |
| CLK_SAI3_PLL3Q |
| CLK_SAI4_PLL3Q |
| CLK_RNG1_LSI |
| CLK_RNG2_LSI |
| CLK_LPTIM1_PCLK1 |
| CLK_LPTIM23_PCLK3 |
| CLK_LPTIM45_LSE |
| >; |
| |
| /* VCO = 1066.0 MHz => P = 266 (AXI), Q = 533 (GPU), R = 533 (DDR) */ |
| pll2: st,pll@1 { |
| compatible = "st,stm32mp1-pll"; |
| reg = <1>; |
| cfg = < 2 65 1 0 0 PQR(1,1,1) >; |
| frac = < 0x1400 >; |
| bootph-all; |
| }; |
| |
| /* VCO = 417.8 MHz => P = 209, Q = 24, R = 11 */ |
| pll3: st,pll@2 { |
| compatible = "st,stm32mp1-pll"; |
| reg = <2>; |
| cfg = < 1 33 1 16 36 PQR(1,1,1) >; |
| frac = < 0x1a04 >; |
| bootph-all; |
| }; |
| |
| /* VCO = 594.0 MHz => P = 99, Q = 74, R = 74 */ |
| pll4: st,pll@3 { |
| compatible = "st,stm32mp1-pll"; |
| reg = <3>; |
| cfg = < 3 98 5 7 7 PQR(1,1,1) >; |
| bootph-all; |
| }; |
| }; |
| |
| &sdmmc1 { |
| bootph-pre-ram; |
| }; |
| |
| &sdmmc1_b4_pins_a { |
| bootph-pre-ram; |
| pins1 { |
| bootph-pre-ram; |
| }; |
| pins2 { |
| bootph-pre-ram; |
| }; |
| }; |
| |
| &sdmmc1_dir_pins_a { |
| bootph-pre-ram; |
| pins1 { |
| bootph-pre-ram; |
| }; |
| pins2 { |
| bootph-pre-ram; |
| }; |
| }; |
| |
| &sdmmc2 { |
| bootph-pre-ram; |
| }; |
| |
| &sdmmc2_b4_pins_a { |
| bootph-pre-ram; |
| pins1 { |
| bootph-pre-ram; |
| }; |
| pins2 { |
| bootph-pre-ram; |
| }; |
| }; |
| |
| &sdmmc2_d47_pins_a { |
| bootph-pre-ram; |
| pins { |
| bootph-pre-ram; |
| }; |
| }; |
| |
| &uart4 { |
| bootph-all; |
| }; |
| |
| &uart4_pins_a { |
| bootph-all; |
| pins1 { |
| bootph-all; |
| }; |
| pins2 { |
| bootph-all; |
| /* pull-up on rx to avoid floating level */ |
| bias-pull-up; |
| }; |
| }; |