| /* |
| * Copyright 2008 Extreme Engineering Solutions, Inc. |
| * Copyright 2007-2008 Freescale Semiconductor, Inc. |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| /* |
| * xpedite537x board configuration file |
| */ |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| /* |
| * High Level Configuration Options |
| */ |
| #define CONFIG_BOOKE 1 /* BOOKE */ |
| #define CONFIG_E500 1 /* BOOKE e500 family */ |
| #define CONFIG_MPC8572 1 |
| #define CONFIG_XPEDITE5370 1 |
| #define CONFIG_SYS_BOARD_NAME "XPedite5370" |
| #define CONFIG_SYS_FORM_3U_VPX 1 |
| #define CONFIG_BOARD_EARLY_INIT_R /* Call board_pre_init */ |
| #define CONFIG_DISPLAY_BOARDINFO |
| |
| #ifndef CONFIG_SYS_TEXT_BASE |
| #define CONFIG_SYS_TEXT_BASE 0xfff80000 |
| #endif |
| |
| #define CONFIG_PCI 1 /* Enable PCI/PCIE */ |
| #define CONFIG_PCI_PNP 1 /* do pci plug-and-play */ |
| #define CONFIG_PCI_SCAN_SHOW 1 /* show pci devices on startup */ |
| #define CONFIG_PCIE1 1 /* PCIE controler 1 */ |
| #define CONFIG_PCIE2 1 /* PCIE controler 2 */ |
| #define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */ |
| #define CONFIG_PCI_INDIRECT_BRIDGE 1 /* indirect PCI bridge support */ |
| #define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */ |
| #define CONFIG_FSL_PCIE_RESET 1 /* need PCIe reset errata */ |
| #define CONFIG_FSL_LAW 1 /* Use common FSL init code */ |
| #define CONFIG_FSL_ELBC 1 |
| |
| /* |
| * Multicore config |
| */ |
| #define CONFIG_MP |
| #define CONFIG_BPTR_VIRT_ADDR 0xee000000 /* virt boot page address */ |
| #define CONFIG_MPC8xxx_DISABLE_BPTR /* Don't leave BPTR enabled */ |
| |
| /* |
| * DDR config |
| */ |
| #define CONFIG_SYS_FSL_DDR2 |
| #undef CONFIG_FSL_DDR_INTERACTIVE |
| #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */ |
| #define CONFIG_DDR_SPD |
| #define CONFIG_MEM_INIT_VALUE 0xdeadbeef |
| #define SPD_EEPROM_ADDRESS1 0x54 /* Both channels use the */ |
| #define SPD_EEPROM_ADDRESS2 0x54 /* same SPD data */ |
| #define SPD_EEPROM_OFFSET 0x200 /* OFFSET of SPD in EEPROM */ |
| #define CONFIG_NUM_DDR_CONTROLLERS 2 |
| #define CONFIG_DIMM_SLOTS_PER_CTLR 1 |
| #define CONFIG_CHIP_SELECTS_PER_CTRL 1 |
| #define CONFIG_DDR_ECC |
| #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER |
| #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/ |
| #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE |
| #define CONFIG_VERY_BIG_RAM |
| |
| #ifndef __ASSEMBLY__ |
| extern unsigned long get_board_sys_clk(unsigned long dummy); |
| extern unsigned long get_board_ddr_clk(unsigned long dummy); |
| #endif |
| |
| #define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) /* sysclk for MPC85xx */ |
| #define CONFIG_DDR_CLK_FREQ get_board_ddr_clk(0) /* ddrclk for MPC85xx */ |
| |
| /* |
| * These can be toggled for performance analysis, otherwise use default. |
| */ |
| #define CONFIG_L2_CACHE /* toggle L2 cache */ |
| #define CONFIG_BTB /* toggle branch predition */ |
| #define CONFIG_ENABLE_36BIT_PHYS 1 |
| |
| #define CONFIG_SYS_CCSRBAR 0xef000000 |
| #define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR |
| |
| /* |
| * Diagnostics |
| */ |
| #define CONFIG_SYS_ALT_MEMTEST |
| #define CONFIG_SYS_MEMTEST_START 0x10000000 |
| #define CONFIG_SYS_MEMTEST_END 0x20000000 |
| #define CONFIG_POST (CONFIG_SYS_POST_MEMORY | \ |
| CONFIG_SYS_POST_I2C) |
| #define I2C_ADDR_LIST {CONFIG_SYS_I2C_DS1621_ADDR, \ |
| CONFIG_SYS_I2C_DS4510_ADDR, \ |
| CONFIG_SYS_I2C_EEPROM_ADDR, \ |
| CONFIG_SYS_I2C_LM90_ADDR, \ |
| CONFIG_SYS_I2C_PCA953X_ADDR0, \ |
| CONFIG_SYS_I2C_PCA953X_ADDR1, \ |
| CONFIG_SYS_I2C_PCA953X_ADDR2, \ |
| CONFIG_SYS_I2C_PCA953X_ADDR3, \ |
| CONFIG_SYS_I2C_PEX8518_ADDR, \ |
| CONFIG_SYS_I2C_RTC_ADDR} |
| /* The XPedite5370 can host an XMC which has an EEPROM at address 0x50 */ |
| #define I2C_ADDR_IGNORE_LIST {0x50} |
| |
| /* |
| * Memory map |
| * 0x0000_0000 0x7fff_ffff DDR 2G Cacheable |
| * 0x8000_0000 0xbfff_ffff PCIe1 Mem 1G non-cacheable |
| * 0xc000_0000 0xcfff_ffff PCIe2 Mem 256M non-cacheable |
| * 0xe000_0000 0xe7ff_ffff SRAM/SSRAM/L1 Cache 128M non-cacheable |
| * 0xe800_0000 0xe87f_ffff PCIe1 IO 8M non-cacheable |
| * 0xe880_0000 0xe8ff_ffff PCIe2 IO 8M non-cacheable |
| * 0xee00_0000 0xee00_ffff Boot page translation 4K non-cacheable |
| * 0xef00_0000 0xef0f_ffff CCSR/IMMR 1M non-cacheable |
| * 0xef80_0000 0xef8f_ffff NAND Flash 1M non-cacheable |
| * 0xf000_0000 0xf7ff_ffff NOR Flash 2 128M non-cacheable |
| * 0xf800_0000 0xffff_ffff NOR Flash 1 128M non-cacheable |
| */ |
| |
| #define CONFIG_SYS_LBC_LCRR (LCRR_CLKDIV_8 | LCRR_EADC_3) |
| |
| /* |
| * NAND flash configuration |
| */ |
| #define CONFIG_SYS_NAND_BASE 0xef800000 |
| #define CONFIG_SYS_NAND_BASE2 0xef840000 /* Unused at this time */ |
| #define CONFIG_SYS_NAND_BASE_LIST {CONFIG_SYS_NAND_BASE, \ |
| CONFIG_SYS_NAND_BASE2} |
| #define CONFIG_SYS_MAX_NAND_DEVICE 2 |
| #define CONFIG_NAND_FSL_ELBC |
| |
| /* |
| * NOR flash configuration |
| */ |
| #define CONFIG_SYS_FLASH_BASE 0xf8000000 |
| #define CONFIG_SYS_FLASH_BASE2 0xf0000000 |
| #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE2} |
| #define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */ |
| #define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ |
| #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ |
| #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ |
| #define CONFIG_FLASH_CFI_DRIVER |
| #define CONFIG_SYS_FLASH_CFI |
| #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE |
| #define CONFIG_SYS_FLASH_AUTOPROTECT_LIST { {0xfff40000, 0xc0000}, \ |
| {0xf7f40000, 0xc0000} } |
| #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ |
| |
| /* |
| * Chip select configuration |
| */ |
| /* NOR Flash 0 on CS0 */ |
| #define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | \ |
| BR_PS_16 | \ |
| BR_V) |
| #define CONFIG_SYS_OR0_PRELIM (OR_AM_128MB | \ |
| OR_GPCM_CSNT | \ |
| OR_GPCM_XACS | \ |
| OR_GPCM_ACS_DIV2 | \ |
| OR_GPCM_SCY_8 | \ |
| OR_GPCM_TRLX | \ |
| OR_GPCM_EHTR | \ |
| OR_GPCM_EAD) |
| |
| /* NOR Flash 1 on CS1 */ |
| #define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_FLASH_BASE2 | \ |
| BR_PS_16 | \ |
| BR_V) |
| #define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR0_PRELIM |
| |
| /* NAND flash on CS2 */ |
| #define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_NAND_BASE | \ |
| (2<<BR_DECC_SHIFT) | \ |
| BR_PS_8 | \ |
| BR_MS_FCM | \ |
| BR_V) |
| |
| /* NAND flash on CS2 */ |
| #define CONFIG_SYS_OR2_PRELIM (OR_AM_256KB | \ |
| OR_FCM_PGS | \ |
| OR_FCM_CSCT | \ |
| OR_FCM_CST | \ |
| OR_FCM_CHT | \ |
| OR_FCM_SCY_1 | \ |
| OR_FCM_TRLX | \ |
| OR_FCM_EHTR) |
| |
| /* NAND flash on CS3 */ |
| #define CONFIG_SYS_BR3_PRELIM (CONFIG_SYS_NAND_BASE2 | \ |
| (2<<BR_DECC_SHIFT) | \ |
| BR_PS_8 | \ |
| BR_MS_FCM | \ |
| BR_V) |
| #define CONFIG_SYS_OR3_PRELIM CONFIG_SYS_OR2_PRELIM |
| |
| /* |
| * Use L1 as initial stack |
| */ |
| #define CONFIG_SYS_INIT_RAM_LOCK 1 |
| #define CONFIG_SYS_INIT_RAM_ADDR 0xe0000000 |
| #define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 |
| |
| #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) |
| #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET |
| |
| #define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 KB for Mon */ |
| #define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */ |
| |
| /* |
| * Serial Port |
| */ |
| #define CONFIG_CONS_INDEX 1 |
| #define CONFIG_SYS_NS16550_SERIAL |
| #define CONFIG_SYS_NS16550_REG_SIZE 1 |
| #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) |
| #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) |
| #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) |
| #define CONFIG_SYS_BAUDRATE_TABLE \ |
| {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} |
| #define CONFIG_BAUDRATE 115200 |
| #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ |
| #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ |
| |
| /* |
| * I2C |
| */ |
| #define CONFIG_SYS_I2C |
| #define CONFIG_SYS_I2C_FSL |
| #define CONFIG_SYS_FSL_I2C_SPEED 400000 |
| #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F |
| #define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 |
| #define CONFIG_SYS_FSL_I2C2_SPEED 400000 |
| #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F |
| #define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 |
| #define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } |
| |
| /* PEX8518 slave I2C interface */ |
| #define CONFIG_SYS_I2C_PEX8518_ADDR 0x70 |
| |
| /* I2C DS1631 temperature sensor */ |
| #define CONFIG_SYS_I2C_DS1621_ADDR 0x48 |
| #define CONFIG_DTT_DS1621 |
| #define CONFIG_DTT_SENSORS { 0 } |
| #define CONFIG_SYS_I2C_LM90_ADDR 0x4c |
| |
| /* I2C EEPROM - AT24C128B */ |
| #define CONFIG_SYS_I2C_EEPROM_ADDR 0x54 |
| #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 |
| #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 /* 64 byte pages */ |
| #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* take up to 10 msec */ |
| |
| /* I2C RTC */ |
| #define CONFIG_RTC_M41T11 1 |
| #define CONFIG_SYS_I2C_RTC_ADDR 0x68 |
| #define CONFIG_SYS_M41T11_BASE_YEAR 2000 |
| |
| /* GPIO/EEPROM/SRAM */ |
| #define CONFIG_DS4510 |
| #define CONFIG_SYS_I2C_DS4510_ADDR 0x51 |
| |
| /* GPIO */ |
| #define CONFIG_PCA953X |
| #define CONFIG_SYS_I2C_PCA953X_ADDR0 0x18 |
| #define CONFIG_SYS_I2C_PCA953X_ADDR1 0x1c |
| #define CONFIG_SYS_I2C_PCA953X_ADDR2 0x1e |
| #define CONFIG_SYS_I2C_PCA953X_ADDR3 0x1f |
| #define CONFIG_SYS_I2C_PCA953X_ADDR CONFIG_SYS_I2C_PCA953X_ADDR0 |
| |
| /* |
| * PU = pulled high, PD = pulled low |
| * I = input, O = output, IO = input/output |
| */ |
| /* PCA9557 @ 0x18*/ |
| #define CONFIG_SYS_PCA953X_C0_SER0_EN 0x01 /* PU; UART0 enable (1: enabled) */ |
| #define CONFIG_SYS_PCA953X_C0_SER0_MODE 0x02 /* PU; UART0 serial mode select */ |
| #define CONFIG_SYS_PCA953X_C0_SER1_EN 0x04 /* PU; UART1 enable (1: enabled) */ |
| #define CONFIG_SYS_PCA953X_C0_SER1_MODE 0x08 /* PU; UART1 serial mode select */ |
| #define CONFIG_SYS_PCA953X_C0_FLASH_PASS_CS 0x10 /* PU; Boot flash CS select */ |
| #define CONFIG_SYS_PCA953X_NVM_WP 0x20 /* PU; Set to 0 to enable NVM writing */ |
| #define CONFIG_SYS_PCA953X_C0_VCORE_VID2 0x40 /* VID2 of ISL6262 */ |
| #define CONFIG_SYS_PCA953X_C0_VCORE_VID3 0x80 /* VID3 of ISL6262 */ |
| |
| /* PCA9557 @ 0x1c*/ |
| #define CONFIG_SYS_PCA953X_XMC0_ROOT0 0x01 /* PU; Low if XMC is RC */ |
| #define CONFIG_SYS_PCA953X_XMC0_MVMR0 0x02 /* XMC EEPROM write protect */ |
| #define CONFIG_SYS_PCA953X_XMC0_WAKE 0x04 /* PU; XMC wake */ |
| #define CONFIG_SYS_PCA953X_XMC0_BIST 0x08 /* PU; XMC built in self test */ |
| #define CONFIG_SYS_PCA953X_XMC_PRESENT 0x10 /* PU; Low if XMC module installed */ |
| #define CONFIG_SYS_PCA953X_PMC_PRESENT 0x20 /* PU; Low if PMC module installed */ |
| #define CONFIG_SYS_PCA953X_PMC0_MONARCH 0x40 /* PMC monarch mode enable */ |
| #define CONFIG_SYS_PCA953X_PMC0_EREADY 0x80 /* PU; PMC PCI eready */ |
| |
| /* PCA9557 @ 0x1e*/ |
| #define CONFIG_SYS_PCA953X_P0_GA0 0x01 /* PU; VPX Geographical address */ |
| #define CONFIG_SYS_PCA953X_P0_GA1 0x02 /* PU; VPX Geographical address */ |
| #define CONFIG_SYS_PCA953X_P0_GA2 0x04 /* PU; VPX Geographical address */ |
| #define CONFIG_SYS_PCA953X_P0_GA3 0x08 /* PU; VPX Geographical address */ |
| #define CONFIG_SYS_PCA953X_P0_GA4 0x10 /* PU; VPX Geographical address */ |
| #define CONFIG_SYS_PCA953X_P0_GAP 0x20 /* PU; tied to VPX P0.GAP */ |
| #define CONFIG_SYS_PCA953X_P1_SYSEN 0x80 /* PU; Pulled high; tied to VPX P1.SYSCON */ |
| |
| /* PCA9557 @ 0x1f */ |
| #define CONFIG_SYS_PCA953X_GPIO_VPX0 0x01 /* PU */ |
| #define CONFIG_SYS_PCA953X_GPIO_VPX1 0x02 /* PU */ |
| #define CONFIG_SYS_PCA953X_GPIO_VPX2 0x04 /* PU */ |
| #define CONFIG_SYS_PCA953X_GPIO_VPX3 0x08 /* PU */ |
| #define CONFIG_SYS_PCA953X_VPX_FRU_WRCTL 0x10 /* PD; I2C master source for FRU SEEPROM */ |
| |
| /* |
| * General PCI |
| * Memory space is mapped 1-1, but I/O space must start from 0. |
| */ |
| /* PCIE1 - VPX P1 */ |
| #define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000 |
| #define CONFIG_SYS_PCIE1_MEM_PHYS CONFIG_SYS_PCIE1_MEM_BUS |
| #define CONFIG_SYS_PCIE1_MEM_SIZE 0x40000000 /* 1G */ |
| #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 |
| #define CONFIG_SYS_PCIE1_IO_PHYS 0xe8000000 |
| #define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000 /* 8M */ |
| |
| /* PCIE2 - PEX8518 */ |
| #define CONFIG_SYS_PCIE2_MEM_BUS 0xc0000000 |
| #define CONFIG_SYS_PCIE2_MEM_PHYS CONFIG_SYS_PCIE2_MEM_BUS |
| #define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 /* 256M */ |
| #define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 |
| #define CONFIG_SYS_PCIE2_IO_PHYS 0xe8800000 |
| #define CONFIG_SYS_PCIE2_IO_SIZE 0x00800000 /* 8M */ |
| |
| /* |
| * Networking options |
| */ |
| #define CONFIG_TSEC_ENET /* tsec ethernet support */ |
| #define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ |
| #define CONFIG_TSEC_TBI |
| #define CONFIG_MII 1 /* MII PHY management */ |
| #define CONFIG_MII_DEFAULT_TSEC 1 /* Allow unregistered phys */ |
| #define CONFIG_ETHPRIME "eTSEC2" |
| |
| /* |
| * In-band SGMII auto-negotiation between TBI and BCM5482S PHY fails, force |
| * 1000mbps SGMII link |
| */ |
| #define CONFIG_TSEC_TBICR_SETTINGS ( \ |
| TBICR_PHY_RESET \ |
| | TBICR_FULL_DUPLEX \ |
| | TBICR_SPEED1_SET \ |
| ) |
| |
| #define CONFIG_TSEC1 1 |
| #define CONFIG_TSEC1_NAME "eTSEC1" |
| #define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) |
| #define TSEC1_PHY_ADDR 1 |
| #define TSEC1_PHYIDX 0 |
| #define CONFIG_HAS_ETH0 |
| |
| #define CONFIG_TSEC2 1 |
| #define CONFIG_TSEC2_NAME "eTSEC2" |
| #define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) |
| #define TSEC2_PHY_ADDR 2 |
| #define TSEC2_PHYIDX 0 |
| #define CONFIG_HAS_ETH1 |
| |
| /* |
| * Command configuration. |
| */ |
| #define CONFIG_CMD_ASKENV |
| #define CONFIG_CMD_DATE |
| #define CONFIG_CMD_DHCP |
| #define CONFIG_CMD_DS4510 |
| #define CONFIG_CMD_DS4510_INFO |
| #define CONFIG_CMD_DTT |
| #define CONFIG_CMD_EEPROM |
| #define CONFIG_CMD_I2C |
| #define CONFIG_CMD_JFFS2 |
| #define CONFIG_CMD_MII |
| #define CONFIG_CMD_NAND |
| #define CONFIG_CMD_PCA953X |
| #define CONFIG_CMD_PCA953X_INFO |
| #define CONFIG_CMD_PCI |
| #define CONFIG_CMD_PCI_ENUM |
| #define CONFIG_CMD_PING |
| #define CONFIG_CMD_SNTP |
| #define CONFIG_CMD_REGINFO |
| |
| /* |
| * Miscellaneous configurable options |
| */ |
| #define CONFIG_SYS_LONGHELP /* undef to save memory */ |
| #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ |
| #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ |
| #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ |
| #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ |
| #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ |
| #define CONFIG_CMDLINE_EDITING 1 /* add command line history */ |
| #define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */ |
| #define CONFIG_LOADADDR 0x1000000 /* default location for tftp and bootm */ |
| #define CONFIG_BOOTDELAY 3 /* -1 disables auto-boot */ |
| #define CONFIG_PANIC_HANG /* do not reset board on panic */ |
| #define CONFIG_PREBOOT /* enable preboot variable */ |
| #define CONFIG_INTEGRITY /* support booting INTEGRITY OS */ |
| |
| /* |
| * For booting Linux, the board info and command line data |
| * have to be in the first 16 MB of memory, since this is |
| * the maximum mapped by the Linux kernel during initialization. |
| */ |
| #define CONFIG_SYS_BOOTMAPSZ (16 << 20) /* Initial Memory map for Linux*/ |
| #define CONFIG_SYS_BOOTM_LEN (16 << 20) /* Increase max gunzip size */ |
| |
| /* |
| * Environment Configuration |
| */ |
| #define CONFIG_ENV_IS_IN_FLASH 1 |
| #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128k (one sector) for env */ |
| #define CONFIG_ENV_SIZE 0x8000 |
| #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - (256 * 1024)) |
| |
| /* |
| * Flash memory map: |
| * fff80000 - ffffffff Pri U-Boot (512 KB) |
| * fff40000 - fff7ffff Pri U-Boot Environment (256 KB) |
| * fff00000 - fff3ffff Pri FDT (256KB) |
| * fef00000 - ffefffff Pri OS image (16MB) |
| * f8000000 - feefffff Pri OS Use/Filesystem (111MB) |
| * |
| * f7f80000 - f7ffffff Sec U-Boot (512 KB) |
| * f7f40000 - f7f7ffff Sec U-Boot Environment (256 KB) |
| * f7f00000 - f7f3ffff Sec FDT (256KB) |
| * f6f00000 - f7efffff Sec OS image (16MB) |
| * f0000000 - f6efffff Sec OS Use/Filesystem (111MB) |
| */ |
| #define CONFIG_UBOOT1_ENV_ADDR __stringify(0xfff80000) |
| #define CONFIG_UBOOT2_ENV_ADDR __stringify(0xf7f80000) |
| #define CONFIG_FDT1_ENV_ADDR __stringify(0xfff00000) |
| #define CONFIG_FDT2_ENV_ADDR __stringify(0xf7f00000) |
| #define CONFIG_OS1_ENV_ADDR __stringify(0xfef00000) |
| #define CONFIG_OS2_ENV_ADDR __stringify(0xf6f00000) |
| |
| #define CONFIG_PROG_UBOOT1 \ |
| "$download_cmd $loadaddr $ubootfile; " \ |
| "if test $? -eq 0; then " \ |
| "protect off "CONFIG_UBOOT1_ENV_ADDR" +80000; " \ |
| "erase "CONFIG_UBOOT1_ENV_ADDR" +80000; " \ |
| "cp.w $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 40000; " \ |
| "protect on "CONFIG_UBOOT1_ENV_ADDR" +80000; " \ |
| "cmp.b $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 80000; " \ |
| "if test $? -ne 0; then " \ |
| "echo PROGRAM FAILED; " \ |
| "else; " \ |
| "echo PROGRAM SUCCEEDED; " \ |
| "fi; " \ |
| "else; " \ |
| "echo DOWNLOAD FAILED; " \ |
| "fi;" |
| |
| #define CONFIG_PROG_UBOOT2 \ |
| "$download_cmd $loadaddr $ubootfile; " \ |
| "if test $? -eq 0; then " \ |
| "protect off "CONFIG_UBOOT2_ENV_ADDR" +80000; " \ |
| "erase "CONFIG_UBOOT2_ENV_ADDR" +80000; " \ |
| "cp.w $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 40000; " \ |
| "protect on "CONFIG_UBOOT2_ENV_ADDR" +80000; " \ |
| "cmp.b $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 80000; " \ |
| "if test $? -ne 0; then " \ |
| "echo PROGRAM FAILED; " \ |
| "else; " \ |
| "echo PROGRAM SUCCEEDED; " \ |
| "fi; " \ |
| "else; " \ |
| "echo DOWNLOAD FAILED; " \ |
| "fi;" |
| |
| #define CONFIG_BOOT_OS_NET \ |
| "$download_cmd $osaddr $osfile; " \ |
| "if test $? -eq 0; then " \ |
| "if test -n $fdtaddr; then " \ |
| "$download_cmd $fdtaddr $fdtfile; " \ |
| "if test $? -eq 0; then " \ |
| "bootm $osaddr - $fdtaddr; " \ |
| "else; " \ |
| "echo FDT DOWNLOAD FAILED; " \ |
| "fi; " \ |
| "else; " \ |
| "bootm $osaddr; " \ |
| "fi; " \ |
| "else; " \ |
| "echo OS DOWNLOAD FAILED; " \ |
| "fi;" |
| |
| #define CONFIG_PROG_OS1 \ |
| "$download_cmd $osaddr $osfile; " \ |
| "if test $? -eq 0; then " \ |
| "erase "CONFIG_OS1_ENV_ADDR" +$filesize; " \ |
| "cp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; " \ |
| "cmp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; " \ |
| "if test $? -ne 0; then " \ |
| "echo OS PROGRAM FAILED; " \ |
| "else; " \ |
| "echo OS PROGRAM SUCCEEDED; " \ |
| "fi; " \ |
| "else; " \ |
| "echo OS DOWNLOAD FAILED; " \ |
| "fi;" |
| |
| #define CONFIG_PROG_OS2 \ |
| "$download_cmd $osaddr $osfile; " \ |
| "if test $? -eq 0; then " \ |
| "erase "CONFIG_OS2_ENV_ADDR" +$filesize; " \ |
| "cp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; " \ |
| "cmp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; " \ |
| "if test $? -ne 0; then " \ |
| "echo OS PROGRAM FAILED; " \ |
| "else; " \ |
| "echo OS PROGRAM SUCCEEDED; " \ |
| "fi; " \ |
| "else; " \ |
| "echo OS DOWNLOAD FAILED; " \ |
| "fi;" |
| |
| #define CONFIG_PROG_FDT1 \ |
| "$download_cmd $fdtaddr $fdtfile; " \ |
| "if test $? -eq 0; then " \ |
| "erase "CONFIG_FDT1_ENV_ADDR" +$filesize;" \ |
| "cp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; " \ |
| "cmp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; " \ |
| "if test $? -ne 0; then " \ |
| "echo FDT PROGRAM FAILED; " \ |
| "else; " \ |
| "echo FDT PROGRAM SUCCEEDED; " \ |
| "fi; " \ |
| "else; " \ |
| "echo FDT DOWNLOAD FAILED; " \ |
| "fi;" |
| |
| #define CONFIG_PROG_FDT2 \ |
| "$download_cmd $fdtaddr $fdtfile; " \ |
| "if test $? -eq 0; then " \ |
| "erase "CONFIG_FDT2_ENV_ADDR" +$filesize;" \ |
| "cp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; " \ |
| "cmp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; " \ |
| "if test $? -ne 0; then " \ |
| "echo FDT PROGRAM FAILED; " \ |
| "else; " \ |
| "echo FDT PROGRAM SUCCEEDED; " \ |
| "fi; " \ |
| "else; " \ |
| "echo FDT DOWNLOAD FAILED; " \ |
| "fi;" |
| |
| #define CONFIG_EXTRA_ENV_SETTINGS \ |
| "autoload=yes\0" \ |
| "download_cmd=tftp\0" \ |
| "console_args=console=ttyS0,115200\0" \ |
| "root_args=root=/dev/nfs rw\0" \ |
| "misc_args=ip=on\0" \ |
| "set_bootargs=setenv bootargs ${console_args} ${root_args} ${misc_args}\0" \ |
| "bootfile=/home/user/file\0" \ |
| "osfile=/home/user/board.uImage\0" \ |
| "fdtfile=/home/user/board.dtb\0" \ |
| "ubootfile=/home/user/u-boot.bin\0" \ |
| "fdtaddr=c00000\0" \ |
| "osaddr=0x1000000\0" \ |
| "loadaddr=0x1000000\0" \ |
| "prog_uboot1="CONFIG_PROG_UBOOT1"\0" \ |
| "prog_uboot2="CONFIG_PROG_UBOOT2"\0" \ |
| "prog_os1="CONFIG_PROG_OS1"\0" \ |
| "prog_os2="CONFIG_PROG_OS2"\0" \ |
| "prog_fdt1="CONFIG_PROG_FDT1"\0" \ |
| "prog_fdt2="CONFIG_PROG_FDT2"\0" \ |
| "bootcmd_net=run set_bootargs; "CONFIG_BOOT_OS_NET"\0" \ |
| "bootcmd_flash1=run set_bootargs; " \ |
| "bootm "CONFIG_OS1_ENV_ADDR" - "CONFIG_FDT1_ENV_ADDR"\0"\ |
| "bootcmd_flash2=run set_bootargs; " \ |
| "bootm "CONFIG_OS2_ENV_ADDR" - "CONFIG_FDT2_ENV_ADDR"\0"\ |
| "bootcmd=run bootcmd_flash1\0" |
| #endif /* __CONFIG_H */ |