| // SPDX-License-Identifier: GPL-2.0-only |
| |
| #include "msm8916-pm8916.dtsi" |
| #include "msm8916-modem-qdsp6.dtsi" |
| |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/input/input.h> |
| #include <dt-bindings/interrupt-controller/irq.h> |
| #include <dt-bindings/pinctrl/qcom,pmic-gpio.h> |
| |
| / { |
| aliases { |
| mmc0 = &sdhc_1; /* eMMC */ |
| mmc1 = &sdhc_2; /* SD card */ |
| serial0 = &blsp_uart2; |
| }; |
| |
| chosen { |
| stdout-path = "serial0"; |
| }; |
| |
| reserved-memory { |
| /* Additional memory used by Samsung firmware modifications */ |
| tz-apps@85a00000 { |
| reg = <0x0 0x85a00000 0x0 0x600000>; |
| no-map; |
| }; |
| }; |
| |
| battery: battery { |
| compatible = "simple-battery"; |
| precharge-current-microamp = <450000>; |
| precharge-upper-limit-microvolt = <3500000>; |
| }; |
| |
| clk_pwm_backlight: backlight { |
| compatible = "pwm-backlight"; |
| pwms = <&clk_pwm 0 100000>; |
| |
| enable-gpios = <&tlmm 98 GPIO_ACTIVE_HIGH>; |
| |
| brightness-levels = <0 255>; |
| num-interpolated-steps = <255>; |
| default-brightness-level = <128>; |
| |
| pinctrl-0 = <&backlight_en_default>; |
| pinctrl-names = "default"; |
| }; |
| |
| clk_pwm: pwm { |
| compatible = "clk-pwm"; |
| #pwm-cells = <2>; |
| |
| clocks = <&gcc GCC_GP2_CLK>; |
| |
| pinctrl-0 = <&backlight_pwm_default>; |
| pinctrl-names = "default"; |
| }; |
| |
| gpio-keys { |
| compatible = "gpio-keys"; |
| |
| pinctrl-0 = <&gpio_keys_default>; |
| pinctrl-names = "default"; |
| |
| label = "GPIO Buttons"; |
| |
| button-volume-up { |
| label = "Volume Up"; |
| gpios = <&tlmm 107 GPIO_ACTIVE_LOW>; |
| linux,code = <KEY_VOLUMEUP>; |
| }; |
| |
| button-home { |
| label = "Home"; |
| gpios = <&tlmm 109 GPIO_ACTIVE_LOW>; |
| linux,code = <KEY_HOMEPAGE>; |
| }; |
| }; |
| |
| haptic { |
| compatible = "regulator-haptic"; |
| haptic-supply = <®_motor_vdd>; |
| min-microvolt = <3300000>; |
| max-microvolt = <3300000>; |
| }; |
| |
| i2c_nfc: i2c-nfc { |
| compatible = "i2c-gpio"; |
| sda-gpios = <&tlmm 0 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; |
| scl-gpios = <&tlmm 1 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; |
| |
| pinctrl-0 = <&nfc_i2c_default>; |
| pinctrl-names = "default"; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| s3fwrn5_nfc: nfc@27 { |
| compatible = "samsung,s3fwrn5-i2c"; |
| reg = <0x27>; |
| |
| interrupts-extended = <&tlmm 21 IRQ_TYPE_EDGE_RISING>; |
| |
| en-gpios = <&tlmm 20 GPIO_ACTIVE_HIGH>; |
| wake-gpios = <&tlmm 49 GPIO_ACTIVE_HIGH>; |
| |
| clocks = <&rpmcc RPM_SMD_BB_CLK2_PIN>; |
| |
| pinctrl-0 = <&nfc_default>, <&nfc_clk_req>; |
| pinctrl-names = "default"; |
| |
| status = "disabled"; |
| }; |
| }; |
| |
| reg_motor_vdd: regulator-motor-vdd { |
| compatible = "regulator-fixed"; |
| regulator-name = "motor_vdd"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| |
| gpio = <&tlmm 72 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| |
| pinctrl-0 = <&motor_en_default>; |
| pinctrl-names = "default"; |
| }; |
| |
| reg_vdd_tsp_a: regulator-vdd-tsp-a { |
| compatible = "regulator-fixed"; |
| regulator-name = "vdd_tsp_a"; |
| regulator-min-microvolt = <3000000>; |
| regulator-max-microvolt = <3000000>; |
| |
| gpio = <&tlmm 73 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| |
| pinctrl-0 = <&tsp_en_default>; |
| pinctrl-names = "default"; |
| }; |
| }; |
| |
| &blsp_i2c1 { |
| status = "okay"; |
| |
| muic: extcon@25 { |
| compatible = "siliconmitus,sm5502-muic"; |
| reg = <0x25>; |
| interrupts-extended = <&tlmm 12 IRQ_TYPE_EDGE_FALLING>; |
| pinctrl-0 = <&muic_int_default>; |
| pinctrl-names = "default"; |
| |
| usb_con: connector { |
| compatible = "usb-b-connector"; |
| label = "micro-USB"; |
| type = "micro"; |
| }; |
| }; |
| }; |
| |
| &blsp_i2c2 { |
| /* Available sensors vary depending on model variant */ |
| status = "okay"; |
| |
| bosch_accel: accelerometer@10 { |
| compatible = "bosch,bmc150_accel"; |
| reg = <0x10>; |
| interrupts-extended = <&tlmm 115 IRQ_TYPE_EDGE_RISING>; |
| |
| vdd-supply = <&pm8916_l5>; |
| vddio-supply = <&pm8916_l5>; |
| |
| pinctrl-0 = <&accel_int_default>; |
| pinctrl-names = "default"; |
| |
| mount-matrix = "0", "-1", "0", |
| "-1", "0", "0", |
| "0", "0", "1"; |
| |
| status = "disabled"; |
| }; |
| |
| bosch_magn: magnetometer@12 { |
| compatible = "bosch,bmc150_magn"; |
| reg = <0x12>; |
| |
| vdd-supply = <&pm8916_l5>; |
| vddio-supply = <&pm8916_l5>; |
| |
| mount-matrix = "0", "-1", "0", |
| "-1", "0", "0", |
| "0", "0", "1"; |
| |
| status = "disabled"; |
| }; |
| |
| st_accel: accelerometer@1d { |
| compatible = "st,lsm303c-accel"; |
| reg = <0x1d>; |
| interrupts-extended = <&tlmm 115 IRQ_TYPE_LEVEL_HIGH>; |
| |
| vdd-supply = <&pm8916_l17>; |
| vddio-supply = <&pm8916_l5>; |
| |
| pinctrl-0 = <&accel_int_default>; |
| pinctrl-names = "default"; |
| |
| st,drdy-int-pin = <1>; |
| mount-matrix = "0", "-1", "0", |
| "1", "0", "0", |
| "0", "0", "-1"; |
| |
| status = "disabled"; |
| }; |
| |
| st_magn: magnetometer@1e { |
| compatible = "st,lsm303c-magn"; |
| reg = <0x1e>; |
| |
| vdd-supply = <&pm8916_l17>; |
| vddio-supply = <&pm8916_l5>; |
| |
| mount-matrix = "0", "-1", "0", |
| "1", "0", "0", |
| "0", "0", "-1"; |
| |
| status = "disabled"; |
| }; |
| }; |
| |
| &blsp_i2c4 { |
| status = "okay"; |
| |
| fuel-gauge@35 { |
| compatible = "richtek,rt5033-battery"; |
| reg = <0x35>; |
| |
| interrupts-extended = <&tlmm 121 IRQ_TYPE_EDGE_FALLING>; |
| |
| pinctrl-0 = <&fg_alert_default>; |
| pinctrl-names = "default"; |
| |
| power-supplies = <&charger>; |
| }; |
| }; |
| |
| &blsp_i2c5 { |
| status = "okay"; |
| |
| touchscreen: touchscreen@20 { |
| compatible = "zinitix,bt541"; |
| reg = <0x20>; |
| |
| interrupts-extended = <&tlmm 13 IRQ_TYPE_EDGE_FALLING>; |
| |
| touchscreen-size-x = <540>; |
| touchscreen-size-y = <960>; |
| |
| vcca-supply = <®_vdd_tsp_a>; |
| vdd-supply = <&pm8916_l6>; |
| |
| pinctrl-0 = <&tsp_int_default>; |
| pinctrl-names = "default"; |
| }; |
| }; |
| |
| &blsp_i2c6 { |
| status = "okay"; |
| |
| pmic@34 { |
| compatible = "richtek,rt5033"; |
| reg = <0x34>; |
| |
| interrupts-extended = <&tlmm 62 IRQ_TYPE_EDGE_FALLING>; |
| |
| pinctrl-0 = <&pmic_int_default>; |
| pinctrl-names = "default"; |
| |
| regulators { |
| rt5033_reg_safe_ldo: SAFE_LDO { |
| regulator-min-microvolt = <4900000>; |
| regulator-max-microvolt = <4900000>; |
| regulator-always-on; |
| }; |
| |
| /* |
| * Needed for camera, but not used yet. |
| * Define empty nodes to allow disabling the unused |
| * regulators. |
| */ |
| LDO {}; |
| BUCK {}; |
| }; |
| |
| charger: charger { |
| compatible = "richtek,rt5033-charger"; |
| monitored-battery = <&battery>; |
| richtek,usb-connector = <&usb_con>; |
| }; |
| }; |
| }; |
| |
| &blsp_uart2 { |
| status = "okay"; |
| }; |
| |
| &mpss_mem { |
| reg = <0x0 0x86800000 0x0 0x5000000>; |
| }; |
| |
| &pm8916_resin { |
| linux,code = <KEY_VOLUMEDOWN>; |
| status = "okay"; |
| }; |
| |
| &pm8916_rpm_regulators { |
| pm8916_l17: l17 { |
| regulator-min-microvolt = <2850000>; |
| regulator-max-microvolt = <2850000>; |
| }; |
| }; |
| |
| &sdhc_1 { |
| status = "okay"; |
| }; |
| |
| &sdhc_2 { |
| pinctrl-0 = <&sdc2_default &sdc2_cd_default>; |
| pinctrl-1 = <&sdc2_sleep &sdc2_cd_default>; |
| pinctrl-names = "default", "sleep"; |
| |
| cd-gpios = <&tlmm 38 GPIO_ACTIVE_LOW>; |
| |
| status = "okay"; |
| }; |
| |
| &sound { |
| model = "msm8916-1mic"; |
| audio-routing = |
| "AMIC1", "MIC BIAS External1", |
| "AMIC2", "MIC BIAS Internal2", |
| "AMIC3", "MIC BIAS External1"; |
| }; |
| |
| &usb { |
| extcon = <&muic>, <&muic>; |
| status = "okay"; |
| }; |
| |
| &usb_hs_phy { |
| extcon = <&muic>; |
| }; |
| |
| &venus { |
| status = "okay"; |
| }; |
| |
| &venus_mem { |
| status = "okay"; |
| }; |
| |
| &wcnss { |
| status = "okay"; |
| }; |
| |
| &wcnss_iris { |
| compatible = "qcom,wcn3620"; |
| }; |
| |
| &wcnss_mem { |
| status = "okay"; |
| }; |
| |
| &tlmm { |
| accel_int_default: accel-int-default-state { |
| pins = "gpio115"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| backlight_en_default: backlight-en-default-state { |
| pins = "gpio98"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| backlight_pwm_default: backlight-pwm-default-state { |
| pins = "gpio50"; |
| function = "gcc_gp2_clk_a"; |
| }; |
| |
| fg_alert_default: fg-alert-default-state { |
| pins = "gpio121"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| gpio_keys_default: gpio-keys-default-state { |
| pins = "gpio107", "gpio109"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-pull-up; |
| }; |
| |
| motor_en_default: motor-en-default-state { |
| pins = "gpio72"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| muic_int_default: muic-int-default-state { |
| pins = "gpio12"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| nfc_default: nfc-default-state { |
| irq-pins { |
| pins = "gpio21"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-pull-down; |
| }; |
| |
| nfc-pins { |
| pins = "gpio20", "gpio49"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| }; |
| |
| nfc_i2c_default: nfc-i2c-default-state { |
| pins = "gpio0", "gpio1"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| pmic_int_default: pmic-int-default-state { |
| pins = "gpio62"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| sdc2_cd_default: sdc2-cd-default-state { |
| pins = "gpio38"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| tsp_en_default: tsp-en-default-state { |
| pins = "gpio73"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| tsp_int_default: tsp-int-default-state { |
| pins = "gpio13"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| }; |
| |
| &pm8916_gpios { |
| nfc_clk_req: nfc-clk-req-state { |
| pins = "gpio2"; |
| function = "func1"; |
| power-source = <PM8916_GPIO_L2>; |
| bias-disable; |
| input-enable; |
| }; |
| }; |