| // SPDX-License-Identifier: GPL-2.0 |
| /* |
| * Copyright (C) 2012 Texas Instruments Incorporated - https://www.ti.com/ |
| * Copyright (C) 2018 Robert Bosch Power Tools GmbH |
| */ |
| /dts-v1/; |
| |
| #include "am33xx.dtsi" |
| #include <dt-bindings/input/input.h> |
| #include <dt-bindings/interrupt-controller/irq.h> |
| |
| / { |
| model = "Bosch AM335x Guardian"; |
| compatible = "bosch,am335x-guardian", "ti,am33xx"; |
| |
| chosen { |
| stdout-path = &uart0; |
| tick-timer = &timer2; |
| }; |
| |
| cpus { |
| cpu@0 { |
| cpu0-supply = <&dcdc2_reg>; |
| }; |
| }; |
| |
| memory@80000000 { |
| device_type = "memory"; |
| reg = <0x80000000 0x10000000>; /* 256 MB */ |
| }; |
| |
| guardian_buttons: gpio-keys { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&guardian_button_pins>; |
| compatible = "gpio-keys"; |
| |
| select-button { |
| label = "guardian-select-button"; |
| linux,code = <KEY_5>; |
| gpios = <&gpio1 31 GPIO_ACTIVE_LOW>; |
| wakeup-source; |
| }; |
| |
| power-button { |
| label = "guardian-power-button"; |
| linux,code = <KEY_POWER>; |
| gpios = <&gpio2 21 GPIO_ACTIVE_LOW>; |
| wakeup-source; |
| }; |
| }; |
| |
| guardian_leds: gpio-leds { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&guardian_led_pins>; |
| compatible = "gpio-leds"; |
| |
| life-led { |
| label = "guardian:life-led"; |
| gpios = <&gpio1 26 GPIO_ACTIVE_HIGH>; |
| linux,default-trigger = "heartbeat"; |
| default-state = "off"; |
| }; |
| }; |
| |
| gpio-poweroff { |
| compatible = "gpio-poweroff"; |
| gpios = <&gpio0 1 GPIO_ACTIVE_LOW>; |
| }; |
| |
| panel { |
| compatible = "ti,tilcdc,panel"; |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&lcd_pins_default &lcd_disen_pins>; |
| pinctrl-1 = <&lcd_pins_sleep>; |
| |
| display-timings { |
| timing-320x240 { |
| hactive = <320>; |
| vactive = <240>; |
| hback-porch = <68>; |
| hfront-porch = <20>; |
| hsync-len = <1>; |
| vback-porch = <18>; |
| vfront-porch = <4>; |
| vsync-len = <1>; |
| clock-frequency = <9000000>; |
| hsync-active = <0>; |
| vsync-active = <0>; |
| }; |
| }; |
| panel-info { |
| ac-bias = <255>; |
| ac-bias-intrpt = <0>; |
| dma-burst-sz = <16>; |
| bpp = <24>; |
| bus-width = <16>; |
| fdd = <0x80>; |
| sync-edge = <0>; |
| sync-ctrl = <1>; |
| raster-order = <0>; |
| fifo-th = <0>; |
| }; |
| |
| }; |
| |
| guardian_beeper: pwm-7 { |
| compatible = "ti,omap-dmtimer-pwm"; |
| #pwm-cells = <3>; |
| ti,timers = <&timer7>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&guardian_beeper_pins>; |
| ti,clock-source = <0x01>; |
| }; |
| |
| vmmcsd_fixed: fixedregulator0 { |
| compatible = "regulator-fixed"; |
| regulator-name = "vmmcsd_fixed"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| }; |
| |
| mt_keypad: mt_keypad@0 { |
| compatible = "gpio-mt-keypad"; |
| debounce-delay-ms = <10>; |
| col-scan-delay-us = <2>; |
| keypad,num-lines = <5>; |
| linux,no-autorepeat; |
| gpio-activelow; |
| line-gpios = < |
| &gpio1 24 GPIO_ACTIVE_LOW /*gpio_56*/ |
| &gpio1 23 GPIO_ACTIVE_LOW /*gpio_55*/ |
| &gpio1 22 GPIO_ACTIVE_LOW /*gpio_54*/ |
| &gpio1 20 GPIO_ACTIVE_LOW /*gpio_52*/ |
| &gpio1 16 GPIO_ACTIVE_LOW /*gpio_48*/ |
| >; |
| }; |
| }; |
| |
| &elm { |
| status = "okay"; |
| }; |
| |
| &gpmc { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&nandflash_pins>; |
| ranges = <0 0 0x08000000 0x1000000>; /* CS0: 16MB for NAND */ |
| status = "okay"; |
| |
| nand@0,0 { |
| compatible = "ti,omap2-nand"; |
| reg = <0 0 4>; /* CS0, offset 0, IO size 4 */ |
| interrupt-parent = <&gpmc>; |
| interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */ |
| <1 IRQ_TYPE_NONE>; /* termcount */ |
| rb-gpios = <&gpmc 0 GPIO_ACTIVE_HIGH>; /* gpmc_wait0 */ |
| ti,nand-xfer-type = "prefetch-dma"; |
| ti,nand-ecc-opt = "bch16"; |
| ti,elm-id = <&elm>; |
| nand-bus-width = <8>; |
| gpmc,device-width = <1>; |
| gpmc,sync-clk-ps = <0>; |
| gpmc,cs-on-ns = <0>; |
| gpmc,cs-rd-off-ns = <30>; |
| gpmc,cs-wr-off-ns = <30>; |
| gpmc,adv-on-ns = <0>; |
| gpmc,adv-rd-off-ns = <30>; |
| gpmc,adv-wr-off-ns = <30>; |
| gpmc,we-on-ns = <0>; |
| gpmc,we-off-ns = <15>; |
| gpmc,oe-on-ns = <1>; |
| gpmc,oe-off-ns = <15>; |
| gpmc,access-ns = <30>; |
| gpmc,rd-cycle-ns = <30>; |
| gpmc,wr-cycle-ns = <30>; |
| gpmc,bus-turnaround-ns = <0>; |
| gpmc,cycle2cycle-delay-ns = <0>; |
| gpmc,clk-activation-ns = <0>; |
| gpmc,wr-access-ns = <0>; |
| gpmc,wr-data-mux-bus-ns = <0>; |
| |
| /* |
| * MTD partition table |
| * |
| * All SPL-* partitions are sized to minimal length which can |
| * be independently programmable. For NAND flash this is equal |
| * to size of erase-block. |
| */ |
| #address-cells = <1>; |
| #size-cells = <1>; |
| |
| partition@0 { |
| label = "SPL"; |
| reg = <0x0 0x40000>; |
| }; |
| |
| partition@1 { |
| label = "SPL.backup1"; |
| reg = <0x40000 0x40000>; |
| }; |
| |
| partition@2 { |
| label = "SPL.backup2"; |
| reg = <0x80000 0x40000>; |
| }; |
| |
| partition@3 { |
| label = "SPL.backup3"; |
| reg = <0xc0000 0x40000>; |
| }; |
| |
| partition@4 { |
| label = "u-boot"; |
| reg = <0x100000 0x100000>; |
| }; |
| |
| partition@5 { |
| label = "u-boot.backup1"; |
| reg = <0x200000 0x100000>; |
| }; |
| |
| partition@6 { |
| label = "u-boot-2"; |
| reg = <0x300000 0x100000>; |
| }; |
| |
| partition@7 { |
| label = "u-boot-2.backup1"; |
| reg = <0x400000 0x100000>; |
| }; |
| |
| partition@8 { |
| label = "u-boot-env"; |
| reg = <0x500000 0x40000>; |
| }; |
| |
| partition@9 { |
| label = "u-boot-env.backup1"; |
| reg = <0x540000 0x40000>; |
| }; |
| |
| partition@10 { |
| label = "splash-screen"; |
| reg = <0x580000 0x40000>; |
| }; |
| |
| partition@11 { |
| label = "UBI"; |
| reg = <0x5c0000 0x1fa40000>; |
| }; |
| }; |
| }; |
| |
| &i2c0 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&i2c0_pins>; |
| clock-frequency = <400000>; |
| status = "okay"; |
| |
| tps: tps@24 { |
| reg = <0x24>; |
| }; |
| }; |
| |
| &lcdc { |
| blue-and-red-wiring = "crossed"; |
| status = "okay"; |
| port { |
| lcdc_0: endpoint@0 { |
| remote-endpoint = <0>; |
| }; |
| }; |
| }; |
| |
| &mmc1 { |
| bus-width = <0x4>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&mmc1_pins>; |
| cd-gpios = <&gpio0 6 GPIO_ACTIVE_LOW>; |
| vmmc-supply = <&vmmcsd_fixed>; |
| status = "okay"; |
| }; |
| |
| &rtc { |
| clocks = <&clk_32768_ck>, <&clk_24mhz_clkctrl AM3_CLK_24MHZ_CLKDIV32K_CLKCTRL 0>; |
| clock-names = "ext-clk", "int-clk"; |
| }; |
| |
| &spi0 { |
| ti,pindir-d0-out-d1-in; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&spi0_pins>; |
| status = "okay"; |
| }; |
| |
| #include "../../tps65217.dtsi" |
| |
| &tps { |
| /* |
| * Configure pmic to enter OFF-state instead of SLEEP-state ("RTC-only |
| * mode") at poweroff. Most BeagleBone versions do not support RTC-only |
| * mode and risk hardware damage if this mode is entered. |
| * |
| * For details, see linux-omap mailing list May 2015 thread |
| * [PATCH] ARM: dts: am335x-bone* enable pmic-shutdown-controller |
| * In particular, messages: |
| * https://www.spinics.net/lists/linux-omap/msg118585.html |
| * https://www.spinics.net/lists/linux-omap/msg118615.html |
| * |
| * You can override this later with |
| * &tps { /delete-property/ ti,pmic-shutdown-controller; } |
| * if you want to use RTC-only mode and made sure you are not affected |
| * by the hardware problems. (Tip: double-check by performing a current |
| * measurement after shutdown: it should be less than 1 mA.) |
| */ |
| ti,pmic-shutdown-controller; |
| interrupt-parent = <&intc>; |
| interrupts = <7>; /* NMI */ |
| |
| backlight { |
| isel = <1>; /* 1 - ISET1, 2 ISET2 */ |
| fdim = <500>; /* TPS65217_BL_FDIM_500HZ */ |
| default-brightness = <50>; |
| /* 1(on) - enable current sink, while initialization */ |
| /* 0(off) - disable current sink, while initialization */ |
| isink-en = <1>; |
| }; |
| |
| regulators { |
| dcdc1_reg: regulator@0 { |
| regulator-name = "vdds_dpr"; |
| regulator-always-on; |
| }; |
| |
| dcdc2_reg: regulator@1 { |
| /* VDD_MPU voltage limits 0.95V - 1.26V with +/-4% tolerance */ |
| regulator-name = "vdd_mpu"; |
| regulator-min-microvolt = <925000>; |
| regulator-max-microvolt = <1351500>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| dcdc3_reg: regulator@2 { |
| /* VDD_CORE voltage limits 0.95V - 1.1V with +/-4% tolerance */ |
| regulator-name = "vdd_core"; |
| regulator-min-microvolt = <925000>; |
| regulator-max-microvolt = <1150000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| ldo1_reg: regulator@3 { |
| regulator-name = "vio,vrtc,vdds"; |
| regulator-always-on; |
| }; |
| |
| ldo2_reg: regulator@4 { |
| regulator-name = "vdd_3v3aux"; |
| regulator-always-on; |
| }; |
| |
| ldo3_reg: regulator@5 { |
| regulator-name = "vdd_1v8"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-always-on; |
| }; |
| |
| ldo4_reg: regulator@6 { |
| regulator-name = "vdd_3v3a"; |
| regulator-always-on; |
| }; |
| }; |
| }; |
| |
| &tscadc { |
| status = "okay"; |
| |
| adc { |
| ti,adc-channels = <0 1 2 3 4 5 6>; |
| }; |
| }; |
| |
| &gpio0 { |
| gpio-line-names = |
| "", |
| "", |
| "", |
| "", |
| "", |
| "", |
| "", |
| "", |
| "", |
| "", |
| "", |
| "", |
| "", |
| "", |
| "", |
| "", |
| "", |
| "", |
| "", |
| "", |
| "", |
| "", |
| "", |
| "", |
| "", |
| "", |
| "", |
| "", |
| "", |
| "MirxWakeup", |
| "", |
| ""; |
| }; |
| |
| &gpio3 { |
| ti,gpio-always-on; |
| ti,no-reset-on-init; |
| gpio-line-names = |
| "", |
| "MirxBtReset", |
| "", |
| "CcVolAdcEn", |
| "MirxBlePause", |
| "", |
| "", |
| "", |
| "", |
| "", |
| "", |
| "", |
| "", |
| "", |
| "AspEn", |
| "", |
| "", |
| "", |
| "", |
| "", |
| "", |
| "BatVolAdcEn", |
| "", |
| "", |
| "", |
| "", |
| "", |
| "", |
| "", |
| "", |
| "", |
| ""; |
| }; |
| |
| &uart0 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&uart0_pins>; |
| status = "okay"; |
| }; |
| |
| &uart2 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&uart2_pins>; |
| status = "okay"; |
| }; |
| |
| &usb0 { |
| dr_mode = "peripheral"; |
| }; |
| |
| &usb1 { |
| dr_mode = "host"; |
| /delete-property/dmas; |
| /delete-property/dma-names; |
| }; |
| |
| &am33xx_pinmux { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&clkout2_pin &guardian_interface_pins>; |
| |
| clkout2_pin: clkout2-pins { |
| pinctrl-single,pins = < |
| /* xdma_event_intr1.clkout2 */ |
| AM33XX_IOPAD(0x9b4, PIN_OUTPUT_PULLDOWN | MUX_MODE3) |
| >; |
| }; |
| |
| guardian_interface_pins: interface-pins { |
| pinctrl-single,pins = < |
| /* ADC_BATSENSE_EN */ |
| /* (A14) MCASP0_AHCLKx.gpio3[21] */ |
| AM33XX_IOPAD(0x9ac, PIN_OUTPUT_PULLDOWN | MUX_MODE7 ) |
| /* ADC_COINCELL_EN */ |
| /* (J16) MII1_TX_EN.gpio3[3] */ |
| AM33XX_IOPAD(0x914, PIN_OUTPUT_PULLDOWN | MUX_MODE7 ) |
| /* ASP_ENABLE */ |
| /* (A13) MCASP0_ACLKx.gpio3[14] */ |
| AM33XX_IOPAD(0x990, PIN_OUTPUT_PULLUP | MUX_MODE7) |
| /* (D16) uart1_rxd.uart1_rxd */ |
| AM33XX_IOPAD(0x980, PIN_INPUT | MUX_MODE7) |
| /* (D15) uart1_txd.uart1_txd */ |
| AM33XX_IOPAD(0x984, PIN_INPUT | MUX_MODE7) |
| /*SWITCH-OFF_3V6*/ |
| /* (M18) gpio0[1] */ |
| AM33XX_IOPAD(0x94c, PIN_OUTPUT_PULLUP | MUX_MODE7) |
| /* MIRACULIX */ |
| /* (H17) gmii1_crs.gpio3[1] */ |
| AM33XX_IOPAD(0x90c, PIN_OUTPUT_PULLDOWN | MUX_MODE7 ) |
| /* (H18) rmii1_refclk.gpio0[29] */ |
| AM33XX_IOPAD(0x944, PIN_OUTPUT_PULLDOWN | MUX_MODE7 ) |
| /* (J18) gmii1_txd3.gpio0[16] */ |
| AM33XX_IOPAD(0x91c, PIN_INPUT | MUX_MODE7 ) |
| /* (J17) gmii1_rxdv.gpio3[4] */ |
| AM33XX_IOPAD(0x918, PIN_OUTPUT_PULLDOWN | MUX_MODE7 ) |
| >; |
| }; |
| |
| guardian_beeper_pins: dmtimer7-pins { |
| pinctrl-single,pins = < |
| AM33XX_IOPAD(0x968, PIN_OUTPUT | MUX_MODE5) /* (E18) timer7 */ |
| >; |
| }; |
| |
| guardian_button_pins: guardian-button-pins { |
| pinctrl-single,pins = < |
| AM33XX_IOPAD(0x940, PIN_INPUT | MUX_MODE7) /* (M16) gmii1_rxd0.gpio2[21] */ |
| AM33XX_IOPAD(0x884, PIN_INPUT | MUX_MODE7) /* (V9) gpmc_csn2.gpio1[31] */ |
| >; |
| }; |
| |
| |
| i2c0_pins: i2c0-pins { |
| pinctrl-single,pins = < |
| AM33XX_IOPAD(0x988, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_sda.i2c0_sda */ |
| AM33XX_IOPAD(0x98c, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_scl.i2c0_scl */ |
| >; |
| }; |
| |
| led_bl_pins: gpio-led-bl-pins { |
| pinctrl-single,pins = < |
| /* P9_14, gpmc_a[2].GPIO1[18] (backlight control) */ |
| AM33XX_IOPAD(0x848, PIN_OUTPUT | MUX_MODE7) |
| >; |
| }; |
| |
| lcd_disen_pins: lcd-disen-pins { |
| pinctrl-single,pins = < |
| /* P9_27, mcasp0_fsr.gpio3[19] (lcd_disen) */ |
| AM33XX_IOPAD(0x9a4, PIN_OUTPUT_PULLUP | SLEWCTRL_SLOW | MUX_MODE7) |
| >; |
| }; |
| |
| lcd_pins_default: lcd-default-pins { |
| pinctrl-single,pins = < |
| /* (U10) gpmc_ad8.lcd_data23 */ |
| AM33XX_IOPAD(0x820, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE1) |
| /* (T10) gpmc_ad9.lcd_data22 */ |
| AM33XX_IOPAD(0x824, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE1) |
| /* (T11) gpmc_ad10.lcd_data21 */ |
| AM33XX_IOPAD(0x828, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE1) |
| /* (U12) gpmc_ad11.lcd_data20 */ |
| AM33XX_IOPAD(0x82c, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE1) |
| /* (T12) gpmc_ad12.lcd_data19 */ |
| AM33XX_IOPAD(0x830, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE1) |
| /* (R12) gpmc_ad13.lcd_data18 */ |
| AM33XX_IOPAD(0x834, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE1) |
| /* (V13) gpmc_ad14.lcd_data17 */ |
| AM33XX_IOPAD(0x838, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE1) |
| /* (U13) gpmc_ad15.lcd_data16 */ |
| AM33XX_IOPAD(0x83c, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE1) |
| /* lcd_data0.lcd_data0 */ |
| AM33XX_IOPAD(0x8a0, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE0) |
| /* lcd_data1.lcd_data1 */ |
| AM33XX_IOPAD(0x8a4, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE0) |
| /* lcd_data2.lcd_data2 */ |
| AM33XX_IOPAD(0x8a8, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE0) |
| /* lcd_data3.lcd_data3 */ |
| AM33XX_IOPAD(0x8ac, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE0) |
| /* lcd_data4.lcd_data4 */ |
| AM33XX_IOPAD(0x8b0, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE0) |
| /* lcd_data5.lcd_data5 */ |
| AM33XX_IOPAD(0x8b4, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE0) |
| /* lcd_data6.lcd_data6 */ |
| AM33XX_IOPAD(0x8b8, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE0) |
| /* lcd_data7.lcd_data7 */ |
| AM33XX_IOPAD(0x8bc, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE0) |
| /* lcd_data8.lcd_data8 */ |
| AM33XX_IOPAD(0x8c0, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE0) |
| /* lcd_data9.lcd_data9 */ |
| AM33XX_IOPAD(0x8c4, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE0) |
| /* lcd_data10.lcd_data10 */ |
| AM33XX_IOPAD(0x8c8, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE0) |
| /* lcd_data11.lcd_data11 */ |
| AM33XX_IOPAD(0x8cc, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE0) |
| /* lcd_data12.lcd_data12 */ |
| AM33XX_IOPAD(0x8d0, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE0) |
| /* lcd_data13.lcd_data13 */ |
| AM33XX_IOPAD(0x8d4, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE0) |
| /* lcd_data14.lcd_data14 */ |
| AM33XX_IOPAD(0x8d8, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE0) |
| /* lcd_data15.lcd_data15 */ |
| AM33XX_IOPAD(0x8dc, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE0) |
| /* lcd_vsync.lcd_vsync */ |
| AM33XX_IOPAD(0x8e0, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE0) |
| /* lcd_hsync.lcd_hsync */ |
| AM33XX_IOPAD(0x8e4, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE0) |
| /* lcd_pclk.lcd_pclk */ |
| AM33XX_IOPAD(0x8e8, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE0) |
| /* lcd_ac_bias_en.lcd_ac_bias_en */ |
| AM33XX_IOPAD(0x8ec, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE0) |
| >; |
| }; |
| |
| lcd_pins_sleep: lcd-sleep-pins { |
| pinctrl-single,pins = < |
| /* lcd_data0.lcd_data0 */ |
| AM33XX_IOPAD(0x8a0, PULL_DISABLE | SLEWCTRL_SLOW | MUX_MODE7) |
| /* lcd_data1.lcd_data1 */ |
| AM33XX_IOPAD(0x8a4, PULL_DISABLE | SLEWCTRL_SLOW | MUX_MODE7) |
| /* lcd_data2.lcd_data2 */ |
| AM33XX_IOPAD(0x8a8, PULL_DISABLE | SLEWCTRL_SLOW | MUX_MODE7) |
| /* lcd_data3.lcd_data3 */ |
| AM33XX_IOPAD(0x8ac, PULL_DISABLE | SLEWCTRL_SLOW | MUX_MODE7) |
| /* lcd_data4.lcd_data4 */ |
| AM33XX_IOPAD(0x8b0, PULL_DISABLE | SLEWCTRL_SLOW | MUX_MODE7) |
| /* lcd_data5.lcd_data5 */ |
| AM33XX_IOPAD(0x8b4, PULL_DISABLE | SLEWCTRL_SLOW | MUX_MODE7) |
| /* lcd_data6.lcd_data6 */ |
| AM33XX_IOPAD(0x8b8, PULL_DISABLE | SLEWCTRL_SLOW | MUX_MODE7) |
| /* lcd_data7.lcd_data7 */ |
| AM33XX_IOPAD(0x8bc, PULL_DISABLE | SLEWCTRL_SLOW | MUX_MODE7) |
| /* lcd_data8.lcd_data8 */ |
| AM33XX_IOPAD(0x8c0, PULL_DISABLE | SLEWCTRL_SLOW | MUX_MODE7) |
| /* lcd_data9.lcd_data9 */ |
| AM33XX_IOPAD(0x8c4, PULL_DISABLE | SLEWCTRL_SLOW | MUX_MODE7) |
| /* lcd_data10.lcd_data10 */ |
| AM33XX_IOPAD(0x8c8, PULL_DISABLE | SLEWCTRL_SLOW | MUX_MODE7) |
| /* lcd_data11.lcd_data11 */ |
| AM33XX_IOPAD(0x8cc, PULL_DISABLE | SLEWCTRL_SLOW | MUX_MODE7) |
| /* lcd_data12.lcd_data12 */ |
| AM33XX_IOPAD(0x8d0, PULL_DISABLE | SLEWCTRL_SLOW | MUX_MODE7) |
| /* lcd_data13.lcd_data13 */ |
| AM33XX_IOPAD(0x8d4, PULL_DISABLE | SLEWCTRL_SLOW | MUX_MODE7) |
| /* lcd_data14.lcd_data14 */ |
| AM33XX_IOPAD(0x8d8, PULL_DISABLE | SLEWCTRL_SLOW | MUX_MODE7) |
| /* lcd_data15.lcd_data15 */ |
| AM33XX_IOPAD(0x8dc, PULL_DISABLE | SLEWCTRL_SLOW | MUX_MODE7) |
| /* lcd_vsync.lcd_vsync */ |
| AM33XX_IOPAD(0x8e0, PIN_INPUT_PULLDOWN | SLEWCTRL_SLOW | MUX_MODE7) |
| /* lcd_hsync.lcd_hsync */ |
| AM33XX_IOPAD(0x8e4, PIN_INPUT_PULLDOWN | SLEWCTRL_SLOW | MUX_MODE7) |
| /* lcd_pclk.lcd_pclk */ |
| AM33XX_IOPAD(0x8e8, PIN_INPUT_PULLDOWN | SLEWCTRL_SLOW | MUX_MODE7) |
| /* lcd_ac_bias_en.lcd_ac_bias_en */ |
| AM33XX_IOPAD(0x8ec, PIN_INPUT_PULLDOWN | SLEWCTRL_SLOW | MUX_MODE7) |
| >; |
| }; |
| |
| guardian_led_pins: guardian-led-pins { |
| pinctrl-single,pins = < |
| AM33XX_IOPAD(0x868, PIN_OUTPUT | MUX_MODE7) /* (T16) gpmc_a10.gpio1[26] */ |
| >; |
| }; |
| |
| mmc1_pins: mmc1-pins { |
| pinctrl-single,pins = < |
| AM33XX_IOPAD(0x8f0, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat3.mmc0_dat3 */ |
| AM33XX_IOPAD(0x8f4, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat2.mmc0_dat2 */ |
| AM33XX_IOPAD(0x8f8, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat1.mmc0_dat1 */ |
| AM33XX_IOPAD(0x8fc, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat0.mmc0_dat0 */ |
| AM33XX_IOPAD(0x900, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_clk.mmc0_clk */ |
| AM33XX_IOPAD(0x904, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_cmd.mmc0_cmd */ |
| AM33XX_IOPAD(0x960, PIN_INPUT | MUX_MODE7) /* GPIO0_6 */ |
| >; |
| }; |
| |
| spi0_pins: spi0-pins { |
| pinctrl-single,pins = < |
| /* SPI0_CLK - spi0_clk.spi */ |
| AM33XX_IOPAD(0x950, PIN_OUTPUT_PULLDOWN | MUX_MODE0) |
| /* SPI0_MOSI - spi0_d0.spi0 */ |
| AM33XX_IOPAD(0x954, PIN_OUTPUT_PULLUP | MUX_MODE0) |
| /* SPI0_MISO - spi0_d1.spi0 */ |
| AM33XX_IOPAD(0x958, PIN_INPUT_PULLUP | MUX_MODE0) |
| /* SPI0_CS0 - spi */ |
| AM33XX_IOPAD(0x95c, PIN_OUTPUT_PULLUP | MUX_MODE0) |
| >; |
| }; |
| |
| uart0_pins: uart0-pins { |
| pinctrl-single,pins = < |
| /* uart0_rxd.uart0_rxd */ |
| AM33XX_IOPAD(0x970, PIN_INPUT_PULLUP | MUX_MODE0) |
| /* uart0_txd.uart0_txd */ |
| AM33XX_IOPAD(0x974, PIN_OUTPUT_PULLDOWN | MUX_MODE0) |
| >; |
| }; |
| |
| uart2_pins: uart2-pins { |
| pinctrl-single,pins = < |
| /* K18 uart2_rxd.mirx_txd */ |
| AM33XX_IOPAD(0x92c, PIN_INPUT_PULLUP | MUX_MODE1) |
| /* L18 uart2_txd.mirx_rxd */ |
| AM33XX_IOPAD(0x930, PIN_OUTPUT_PULLDOWN | MUX_MODE1) |
| >; |
| }; |
| |
| nandflash_pins: nandflash-pins { |
| pinctrl-single,pins = < |
| /* (U7) gpmc_ad0.gpmc_ad0 */ |
| AM33XX_IOPAD(0x800, PIN_INPUT | MUX_MODE0) |
| /* (V7) gpmc_ad1.gpmc_ad1 */ |
| AM33XX_IOPAD(0x804, PIN_INPUT | MUX_MODE0) |
| /* (R8) gpmc_ad2.gpmc_ad2 */ |
| AM33XX_IOPAD(0x808, PIN_INPUT | MUX_MODE0) |
| /* (T8) gpmc_ad3.gpmc_ad3 */ |
| AM33XX_IOPAD(0x80c, PIN_INPUT | MUX_MODE0) |
| /* (U8) gpmc_ad4.gpmc_ad4 */ |
| AM33XX_IOPAD(0x810, PIN_INPUT | MUX_MODE0) |
| /* (V8) gpmc_ad5.gpmc_ad5 */ |
| AM33XX_IOPAD(0x814, PIN_INPUT | MUX_MODE0) |
| /* (R9) gpmc_ad6.gpmc_ad6 */ |
| AM33XX_IOPAD(0x818, PIN_INPUT | MUX_MODE0) |
| /* (T9) gpmc_ad7.gpmc_ad7 */ |
| AM33XX_IOPAD(0x81c, PIN_INPUT | MUX_MODE0) |
| /* (T17) gpmc_wait0.gpmc_wait0 */ |
| AM33XX_IOPAD(0x870, PIN_INPUT | MUX_MODE0) |
| /* (U17) gpmc_wpn.gpmc_wpn */ |
| AM33XX_IOPAD(0x874, PIN_OUTPUT | MUX_MODE0) |
| /* (V6) gpmc_csn0.gpmc_csn0 */ |
| AM33XX_IOPAD(0x87c, PIN_OUTPUT | MUX_MODE0) |
| /* (R7) gpmc_advn_ale.gpmc_advn_ale */ |
| AM33XX_IOPAD(0x890, PIN_OUTPUT | MUX_MODE0) |
| /* (T7) gpmc_oen_ren.gpmc_oen_ren */ |
| AM33XX_IOPAD(0x894, PIN_OUTPUT | MUX_MODE0) |
| /* (U6) gpmc_wen.gpmc_wen */ |
| AM33XX_IOPAD(0x898, PIN_OUTPUT | MUX_MODE0) |
| /* (T6) gpmc_be0n_cle.gpmc_be0n_cle */ |
| AM33XX_IOPAD(0x89c, PIN_OUTPUT | MUX_MODE0) |
| >; |
| }; |
| }; |