| // SPDX-License-Identifier: GPL-2.0 |
| /dts-v1/; |
| |
| #include <dt-bindings/clock/qcom,gcc-msm8960.h> |
| #include <dt-bindings/clock/qcom,lcc-msm8960.h> |
| #include <dt-bindings/reset/qcom,gcc-msm8960.h> |
| #include <dt-bindings/clock/qcom,mmcc-msm8960.h> |
| #include <dt-bindings/clock/qcom,rpmcc.h> |
| #include <dt-bindings/soc/qcom,gsbi.h> |
| #include <dt-bindings/interrupt-controller/irq.h> |
| #include <dt-bindings/interrupt-controller/arm-gic.h> |
| / { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| model = "Qualcomm APQ8064"; |
| compatible = "qcom,apq8064"; |
| interrupt-parent = <&intc>; |
| |
| reserved-memory { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| |
| smem_region: smem@80000000 { |
| reg = <0x80000000 0x200000>; |
| no-map; |
| }; |
| |
| wcnss_mem: wcnss@8f000000 { |
| reg = <0x8f000000 0x700000>; |
| no-map; |
| }; |
| }; |
| |
| cpus { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| CPU0: cpu@0 { |
| compatible = "qcom,krait"; |
| enable-method = "qcom,kpss-acc-v1"; |
| device_type = "cpu"; |
| reg = <0>; |
| next-level-cache = <&L2>; |
| qcom,acc = <&acc0>; |
| qcom,saw = <&saw0>; |
| cpu-idle-states = <&CPU_SPC>; |
| }; |
| |
| CPU1: cpu@1 { |
| compatible = "qcom,krait"; |
| enable-method = "qcom,kpss-acc-v1"; |
| device_type = "cpu"; |
| reg = <1>; |
| next-level-cache = <&L2>; |
| qcom,acc = <&acc1>; |
| qcom,saw = <&saw1>; |
| cpu-idle-states = <&CPU_SPC>; |
| }; |
| |
| CPU2: cpu@2 { |
| compatible = "qcom,krait"; |
| enable-method = "qcom,kpss-acc-v1"; |
| device_type = "cpu"; |
| reg = <2>; |
| next-level-cache = <&L2>; |
| qcom,acc = <&acc2>; |
| qcom,saw = <&saw2>; |
| cpu-idle-states = <&CPU_SPC>; |
| }; |
| |
| CPU3: cpu@3 { |
| compatible = "qcom,krait"; |
| enable-method = "qcom,kpss-acc-v1"; |
| device_type = "cpu"; |
| reg = <3>; |
| next-level-cache = <&L2>; |
| qcom,acc = <&acc3>; |
| qcom,saw = <&saw3>; |
| cpu-idle-states = <&CPU_SPC>; |
| }; |
| |
| L2: l2-cache { |
| compatible = "cache"; |
| cache-level = <2>; |
| cache-unified; |
| }; |
| |
| idle-states { |
| CPU_SPC: cpu-spc { |
| compatible = "qcom,idle-state-spc", |
| "arm,idle-state"; |
| entry-latency-us = <400>; |
| exit-latency-us = <900>; |
| min-residency-us = <3000>; |
| }; |
| }; |
| }; |
| |
| memory@0 { |
| device_type = "memory"; |
| reg = <0x0 0x0>; |
| }; |
| |
| thermal-zones { |
| cpu0-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&tsens 7>; |
| coefficients = <1199 0>; |
| |
| trips { |
| cpu_alert0: trip0 { |
| temperature = <75000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| cpu_crit0: trip1 { |
| temperature = <110000>; |
| hysteresis = <2000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| cpu1-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&tsens 8>; |
| coefficients = <1132 0>; |
| |
| trips { |
| cpu_alert1: trip0 { |
| temperature = <75000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| cpu_crit1: trip1 { |
| temperature = <110000>; |
| hysteresis = <2000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| cpu2-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&tsens 9>; |
| coefficients = <1199 0>; |
| |
| trips { |
| cpu_alert2: trip0 { |
| temperature = <75000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| cpu_crit2: trip1 { |
| temperature = <110000>; |
| hysteresis = <2000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| cpu3-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&tsens 10>; |
| coefficients = <1132 0>; |
| |
| trips { |
| cpu_alert3: trip0 { |
| temperature = <75000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| cpu_crit3: trip1 { |
| temperature = <110000>; |
| hysteresis = <2000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| }; |
| |
| cpu-pmu { |
| compatible = "qcom,krait-pmu"; |
| interrupts = <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_HIGH)>; |
| }; |
| |
| clocks { |
| cxo_board: cxo_board { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <19200000>; |
| }; |
| |
| pxo_board: pxo_board { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <27000000>; |
| }; |
| |
| sleep_clk: sleep_clk { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <32768>; |
| }; |
| }; |
| |
| sfpb_mutex: hwmutex { |
| compatible = "qcom,sfpb-mutex"; |
| syscon = <&sfpb_wrapper_mutex 0x604 0x4>; |
| #hwlock-cells = <1>; |
| }; |
| |
| smem { |
| compatible = "qcom,smem"; |
| memory-region = <&smem_region>; |
| |
| hwlocks = <&sfpb_mutex 3>; |
| }; |
| |
| smsm { |
| compatible = "qcom,smsm"; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| qcom,ipc-1 = <&l2cc 8 4>; |
| qcom,ipc-2 = <&l2cc 8 14>; |
| qcom,ipc-3 = <&l2cc 8 23>; |
| qcom,ipc-4 = <&sps_sic_non_secure 0x4094 0>; |
| |
| apps_smsm: apps@0 { |
| reg = <0>; |
| #qcom,smem-state-cells = <1>; |
| }; |
| |
| modem_smsm: modem@1 { |
| reg = <1>; |
| interrupts = <GIC_SPI 38 IRQ_TYPE_EDGE_RISING>; |
| |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| |
| q6_smsm: q6@2 { |
| reg = <2>; |
| interrupts = <GIC_SPI 89 IRQ_TYPE_EDGE_RISING>; |
| |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| |
| wcnss_smsm: wcnss@3 { |
| reg = <3>; |
| interrupts = <GIC_SPI 204 IRQ_TYPE_EDGE_RISING>; |
| |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| |
| dsps_smsm: dsps@4 { |
| reg = <4>; |
| interrupts = <GIC_SPI 137 IRQ_TYPE_EDGE_RISING>; |
| |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| }; |
| |
| firmware { |
| scm { |
| compatible = "qcom,scm-apq8064", "qcom,scm"; |
| |
| clocks = <&rpmcc RPM_DAYTONA_FABRIC_CLK>; |
| clock-names = "core"; |
| }; |
| }; |
| |
| soc: soc { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| compatible = "simple-bus"; |
| |
| tlmm_pinmux: pinctrl@800000 { |
| compatible = "qcom,apq8064-pinctrl"; |
| reg = <0x800000 0x4000>; |
| |
| gpio-controller; |
| gpio-ranges = <&tlmm_pinmux 0 0 90>; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&ps_hold>; |
| }; |
| |
| sfpb_wrapper_mutex: syscon@1200000 { |
| compatible = "syscon"; |
| reg = <0x01200000 0x8000>; |
| }; |
| |
| intc: interrupt-controller@2000000 { |
| compatible = "qcom,msm-qgic2"; |
| interrupt-controller; |
| #interrupt-cells = <3>; |
| reg = <0x02000000 0x1000>, |
| <0x02002000 0x1000>; |
| }; |
| |
| timer@200a000 { |
| compatible = "qcom,kpss-wdt-apq8064", "qcom,kpss-timer", |
| "qcom,msm-timer"; |
| interrupts = <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_EDGE_RISING)>, |
| <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_EDGE_RISING)>, |
| <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_EDGE_RISING)>; |
| reg = <0x0200a000 0x100>; |
| clock-frequency = <27000000>; |
| cpu-offset = <0x80000>; |
| }; |
| |
| acc0: clock-controller@2088000 { |
| compatible = "qcom,kpss-acc-v1"; |
| reg = <0x02088000 0x1000>, <0x02008000 0x1000>; |
| clocks = <&gcc PLL8_VOTE>, <&pxo_board>; |
| clock-names = "pll8_vote", "pxo"; |
| clock-output-names = "acpu0_aux"; |
| #clock-cells = <0>; |
| }; |
| |
| acc1: clock-controller@2098000 { |
| compatible = "qcom,kpss-acc-v1"; |
| reg = <0x02098000 0x1000>, <0x02008000 0x1000>; |
| clocks = <&gcc PLL8_VOTE>, <&pxo_board>; |
| clock-names = "pll8_vote", "pxo"; |
| clock-output-names = "acpu1_aux"; |
| #clock-cells = <0>; |
| }; |
| |
| acc2: clock-controller@20a8000 { |
| compatible = "qcom,kpss-acc-v1"; |
| reg = <0x020a8000 0x1000>, <0x02008000 0x1000>; |
| clocks = <&gcc PLL8_VOTE>, <&pxo_board>; |
| clock-names = "pll8_vote", "pxo"; |
| clock-output-names = "acpu2_aux"; |
| #clock-cells = <0>; |
| }; |
| |
| acc3: clock-controller@20b8000 { |
| compatible = "qcom,kpss-acc-v1"; |
| reg = <0x020b8000 0x1000>, <0x02008000 0x1000>; |
| clocks = <&gcc PLL8_VOTE>, <&pxo_board>; |
| clock-names = "pll8_vote", "pxo"; |
| clock-output-names = "acpu3_aux"; |
| #clock-cells = <0>; |
| }; |
| |
| saw0: power-manager@2089000 { |
| compatible = "qcom,apq8064-saw2-v1.1-cpu", "qcom,saw2"; |
| reg = <0x02089000 0x1000>, <0x02009000 0x1000>; |
| |
| saw0_vreg: regulator { |
| regulator-min-microvolt = <850000>; |
| regulator-max-microvolt = <1300000>; |
| }; |
| }; |
| |
| saw1: power-manager@2099000 { |
| compatible = "qcom,apq8064-saw2-v1.1-cpu", "qcom,saw2"; |
| reg = <0x02099000 0x1000>, <0x02009000 0x1000>; |
| |
| saw1_vreg: regulator { |
| regulator-min-microvolt = <850000>; |
| regulator-max-microvolt = <1300000>; |
| }; |
| }; |
| |
| saw2: power-manager@20a9000 { |
| compatible = "qcom,apq8064-saw2-v1.1-cpu", "qcom,saw2"; |
| reg = <0x020a9000 0x1000>, <0x02009000 0x1000>; |
| |
| saw2_vreg: regulator { |
| regulator-min-microvolt = <850000>; |
| regulator-max-microvolt = <1300000>; |
| }; |
| }; |
| |
| saw3: power-manager@20b9000 { |
| compatible = "qcom,apq8064-saw2-v1.1-cpu", "qcom,saw2"; |
| reg = <0x020b9000 0x1000>, <0x02009000 0x1000>; |
| |
| saw3_vreg: regulator { |
| regulator-min-microvolt = <850000>; |
| regulator-max-microvolt = <1300000>; |
| }; |
| }; |
| |
| sps_sic_non_secure: sps-sic-non-secure@12100000 { |
| compatible = "syscon"; |
| reg = <0x12100000 0x10000>; |
| }; |
| |
| gsbi1: gsbi@12440000 { |
| status = "disabled"; |
| compatible = "qcom,gsbi-v1.0.0"; |
| cell-index = <1>; |
| reg = <0x12440000 0x100>; |
| clocks = <&gcc GSBI1_H_CLK>; |
| clock-names = "iface"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| |
| syscon-tcsr = <&tcsr>; |
| |
| gsbi1_serial: serial@12450000 { |
| compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm"; |
| reg = <0x12450000 0x100>, |
| <0x12400000 0x03>; |
| interrupts = <GIC_SPI 193 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&gcc GSBI1_UART_CLK>, <&gcc GSBI1_H_CLK>; |
| clock-names = "core", "iface"; |
| status = "disabled"; |
| }; |
| |
| gsbi1_i2c: i2c@12460000 { |
| compatible = "qcom,i2c-qup-v1.1.1"; |
| pinctrl-0 = <&i2c1_pins>; |
| pinctrl-1 = <&i2c1_pins_sleep>; |
| pinctrl-names = "default", "sleep"; |
| reg = <0x12460000 0x1000>; |
| interrupts = <GIC_SPI 194 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&gcc GSBI1_QUP_CLK>, <&gcc GSBI1_H_CLK>; |
| clock-names = "core", "iface"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| }; |
| |
| gsbi2: gsbi@12480000 { |
| status = "disabled"; |
| compatible = "qcom,gsbi-v1.0.0"; |
| cell-index = <2>; |
| reg = <0x12480000 0x100>; |
| clocks = <&gcc GSBI2_H_CLK>; |
| clock-names = "iface"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| |
| syscon-tcsr = <&tcsr>; |
| |
| gsbi2_i2c: i2c@124a0000 { |
| compatible = "qcom,i2c-qup-v1.1.1"; |
| reg = <0x124a0000 0x1000>; |
| pinctrl-0 = <&i2c2_pins>; |
| pinctrl-1 = <&i2c2_pins_sleep>; |
| pinctrl-names = "default", "sleep"; |
| interrupts = <GIC_SPI 196 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&gcc GSBI2_QUP_CLK>, <&gcc GSBI2_H_CLK>; |
| clock-names = "core", "iface"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| }; |
| |
| gsbi3: gsbi@16200000 { |
| status = "disabled"; |
| compatible = "qcom,gsbi-v1.0.0"; |
| cell-index = <3>; |
| reg = <0x16200000 0x100>; |
| clocks = <&gcc GSBI3_H_CLK>; |
| clock-names = "iface"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| gsbi3_i2c: i2c@16280000 { |
| compatible = "qcom,i2c-qup-v1.1.1"; |
| pinctrl-0 = <&i2c3_pins>; |
| pinctrl-1 = <&i2c3_pins_sleep>; |
| pinctrl-names = "default", "sleep"; |
| reg = <0x16280000 0x1000>; |
| interrupts = <GIC_SPI 151 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&gcc GSBI3_QUP_CLK>, |
| <&gcc GSBI3_H_CLK>; |
| clock-names = "core", "iface"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| }; |
| |
| gsbi4: gsbi@16300000 { |
| status = "disabled"; |
| compatible = "qcom,gsbi-v1.0.0"; |
| cell-index = <4>; |
| reg = <0x16300000 0x03>; |
| clocks = <&gcc GSBI4_H_CLK>; |
| clock-names = "iface"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| |
| gsbi4_serial: serial@16340000 { |
| compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm"; |
| reg = <0x16340000 0x100>, |
| <0x16300000 0x3>; |
| interrupts = <GIC_SPI 152 IRQ_TYPE_LEVEL_HIGH>; |
| pinctrl-0 = <&gsbi4_uart_pin_a>; |
| pinctrl-names = "default"; |
| clocks = <&gcc GSBI4_UART_CLK>, <&gcc GSBI4_H_CLK>; |
| clock-names = "core", "iface"; |
| status = "disabled"; |
| }; |
| |
| gsbi4_i2c: i2c@16380000 { |
| compatible = "qcom,i2c-qup-v1.1.1"; |
| pinctrl-0 = <&i2c4_pins>; |
| pinctrl-1 = <&i2c4_pins_sleep>; |
| pinctrl-names = "default", "sleep"; |
| reg = <0x16380000 0x1000>; |
| interrupts = <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&gcc GSBI4_QUP_CLK>, |
| <&gcc GSBI4_H_CLK>; |
| clock-names = "core", "iface"; |
| status = "disabled"; |
| }; |
| }; |
| |
| gsbi5: gsbi@1a200000 { |
| status = "disabled"; |
| compatible = "qcom,gsbi-v1.0.0"; |
| cell-index = <5>; |
| reg = <0x1a200000 0x03>; |
| clocks = <&gcc GSBI5_H_CLK>; |
| clock-names = "iface"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| |
| gsbi5_serial: serial@1a240000 { |
| compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm"; |
| reg = <0x1a240000 0x100>, |
| <0x1a200000 0x03>; |
| interrupts = <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&gcc GSBI5_UART_CLK>, <&gcc GSBI5_H_CLK>; |
| clock-names = "core", "iface"; |
| status = "disabled"; |
| }; |
| |
| gsbi5_spi: spi@1a280000 { |
| compatible = "qcom,spi-qup-v1.1.1"; |
| reg = <0x1a280000 0x1000>; |
| interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>; |
| pinctrl-0 = <&spi5_default>; |
| pinctrl-1 = <&spi5_sleep>; |
| pinctrl-names = "default", "sleep"; |
| clocks = <&gcc GSBI5_QUP_CLK>, <&gcc GSBI5_H_CLK>; |
| clock-names = "core", "iface"; |
| status = "disabled"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| }; |
| }; |
| |
| gsbi6: gsbi@16500000 { |
| status = "disabled"; |
| compatible = "qcom,gsbi-v1.0.0"; |
| cell-index = <6>; |
| reg = <0x16500000 0x03>; |
| clocks = <&gcc GSBI6_H_CLK>; |
| clock-names = "iface"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| |
| gsbi6_serial: serial@16540000 { |
| compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm"; |
| reg = <0x16540000 0x100>, |
| <0x16500000 0x03>; |
| interrupts = <GIC_SPI 156 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&gcc GSBI6_UART_CLK>, <&gcc GSBI6_H_CLK>; |
| clock-names = "core", "iface"; |
| status = "disabled"; |
| }; |
| |
| gsbi6_i2c: i2c@16580000 { |
| compatible = "qcom,i2c-qup-v1.1.1"; |
| pinctrl-0 = <&i2c6_pins>; |
| pinctrl-1 = <&i2c6_pins_sleep>; |
| pinctrl-names = "default", "sleep"; |
| reg = <0x16580000 0x1000>; |
| interrupts = <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&gcc GSBI6_QUP_CLK>, |
| <&gcc GSBI6_H_CLK>; |
| clock-names = "core", "iface"; |
| status = "disabled"; |
| }; |
| }; |
| |
| gsbi7: gsbi@16600000 { |
| status = "disabled"; |
| compatible = "qcom,gsbi-v1.0.0"; |
| cell-index = <7>; |
| reg = <0x16600000 0x100>; |
| clocks = <&gcc GSBI7_H_CLK>; |
| clock-names = "iface"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| syscon-tcsr = <&tcsr>; |
| |
| gsbi7_serial: serial@16640000 { |
| compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm"; |
| reg = <0x16640000 0x1000>, |
| <0x16600000 0x1000>; |
| interrupts = <GIC_SPI 158 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&gcc GSBI7_UART_CLK>, <&gcc GSBI7_H_CLK>; |
| clock-names = "core", "iface"; |
| status = "disabled"; |
| }; |
| |
| gsbi7_i2c: i2c@16680000 { |
| compatible = "qcom,i2c-qup-v1.1.1"; |
| pinctrl-0 = <&i2c7_pins>; |
| pinctrl-1 = <&i2c7_pins_sleep>; |
| pinctrl-names = "default", "sleep"; |
| reg = <0x16680000 0x1000>; |
| interrupts = <GIC_SPI 159 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&gcc GSBI7_QUP_CLK>, |
| <&gcc GSBI7_H_CLK>; |
| clock-names = "core", "iface"; |
| status = "disabled"; |
| }; |
| }; |
| |
| rng@1a500000 { |
| compatible = "qcom,prng"; |
| reg = <0x1a500000 0x200>; |
| clocks = <&gcc PRNG_CLK>; |
| clock-names = "core"; |
| }; |
| |
| ssbi2: ssbi@c00000 { |
| compatible = "qcom,ssbi"; |
| reg = <0x00c00000 0x1000>; |
| qcom,controller-type = "pmic-arbiter"; |
| }; |
| |
| ssbi: ssbi@500000 { |
| compatible = "qcom,ssbi"; |
| reg = <0x00500000 0x1000>; |
| qcom,controller-type = "pmic-arbiter"; |
| }; |
| |
| qfprom: efuse@700000 { |
| compatible = "qcom,apq8064-qfprom", "qcom,qfprom"; |
| reg = <0x00700000 0x1000>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| |
| tsens_calib: calib@404 { |
| reg = <0x404 0x10>; |
| }; |
| tsens_backup: backup_calib@414 { |
| reg = <0x414 0x10>; |
| }; |
| }; |
| |
| gcc: clock-controller@900000 { |
| compatible = "qcom,gcc-apq8064", "syscon"; |
| reg = <0x00900000 0x4000>; |
| #clock-cells = <1>; |
| #reset-cells = <1>; |
| clocks = <&cxo_board>, |
| <&pxo_board>, |
| <&lcc PLL4>; |
| clock-names = "cxo", "pxo", "pll4"; |
| |
| tsens: thermal-sensor { |
| compatible = "qcom,msm8960-tsens"; |
| |
| nvmem-cells = <&tsens_calib>, <&tsens_backup>; |
| nvmem-cell-names = "calib", "calib_backup"; |
| interrupts = <GIC_SPI 178 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "uplow"; |
| |
| #qcom,sensors = <11>; |
| #thermal-sensor-cells = <1>; |
| }; |
| }; |
| |
| lcc: clock-controller@28000000 { |
| compatible = "qcom,lcc-apq8064"; |
| reg = <0x28000000 0x1000>; |
| #clock-cells = <1>; |
| #reset-cells = <1>; |
| clocks = <&pxo_board>, |
| <&gcc PLL4_VOTE>, |
| <0>, |
| <0>, <0>, |
| <0>, <0>, |
| <0>; |
| clock-names = "pxo", |
| "pll4_vote", |
| "mi2s_codec_clk", |
| "codec_i2s_mic_codec_clk", |
| "spare_i2s_mic_codec_clk", |
| "codec_i2s_spkr_codec_clk", |
| "spare_i2s_spkr_codec_clk", |
| "pcm_codec_clk"; |
| }; |
| |
| mmcc: clock-controller@4000000 { |
| compatible = "qcom,mmcc-apq8064"; |
| reg = <0x4000000 0x1000>; |
| #clock-cells = <1>; |
| #power-domain-cells = <1>; |
| #reset-cells = <1>; |
| clocks = <&pxo_board>, |
| <&gcc PLL3>, |
| <&gcc PLL8_VOTE>, |
| <&dsi0_phy 1>, |
| <&dsi0_phy 0>, |
| <&dsi1_phy 1>, |
| <&dsi1_phy 0>, |
| <&hdmi_phy>; |
| clock-names = "pxo", |
| "pll3", |
| "pll8_vote", |
| "dsi1pll", |
| "dsi1pllbyte", |
| "dsi2pll", |
| "dsi2pllbyte", |
| "hdmipll"; |
| }; |
| |
| l2cc: clock-controller@2011000 { |
| compatible = "qcom,kpss-gcc-apq8064", "qcom,kpss-gcc", "syscon"; |
| reg = <0x2011000 0x1000>; |
| clocks = <&gcc PLL8_VOTE>, <&pxo_board>; |
| clock-names = "pll8_vote", "pxo"; |
| #clock-cells = <0>; |
| }; |
| |
| rpm: rpm@108000 { |
| compatible = "qcom,rpm-apq8064"; |
| reg = <0x108000 0x1000>; |
| qcom,ipc = <&l2cc 0x8 2>; |
| |
| interrupts = <GIC_SPI 19 IRQ_TYPE_EDGE_RISING>, |
| <GIC_SPI 21 IRQ_TYPE_EDGE_RISING>, |
| <GIC_SPI 22 IRQ_TYPE_EDGE_RISING>; |
| interrupt-names = "ack", "err", "wakeup"; |
| |
| rpmcc: clock-controller { |
| compatible = "qcom,rpmcc-apq8064", "qcom,rpmcc"; |
| #clock-cells = <1>; |
| clocks = <&pxo_board>, <&cxo_board>; |
| clock-names = "pxo", "cxo"; |
| }; |
| }; |
| |
| usb1: usb@12500000 { |
| compatible = "qcom,ci-hdrc"; |
| reg = <0x12500000 0x200>, |
| <0x12500200 0x200>; |
| interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&gcc USB_HS1_XCVR_CLK>, <&gcc USB_HS1_H_CLK>; |
| clock-names = "core", "iface"; |
| assigned-clocks = <&gcc USB_HS1_XCVR_CLK>; |
| assigned-clock-rates = <60000000>; |
| resets = <&gcc USB_HS1_RESET>; |
| reset-names = "core"; |
| phy_type = "ulpi"; |
| ahb-burst-config = <0>; |
| phys = <&usb_hs1_phy>; |
| phy-names = "usb-phy"; |
| status = "disabled"; |
| #reset-cells = <1>; |
| |
| ulpi { |
| usb_hs1_phy: phy { |
| compatible = "qcom,usb-hs-phy-apq8064", |
| "qcom,usb-hs-phy"; |
| clocks = <&sleep_clk>, <&cxo_board>; |
| clock-names = "sleep", "ref"; |
| resets = <&usb1 0>; |
| reset-names = "por"; |
| #phy-cells = <0>; |
| }; |
| }; |
| }; |
| |
| usb3: usb@12520000 { |
| compatible = "qcom,ci-hdrc"; |
| reg = <0x12520000 0x200>, |
| <0x12520200 0x200>; |
| interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&gcc USB_HS3_XCVR_CLK>, <&gcc USB_HS3_H_CLK>; |
| clock-names = "core", "iface"; |
| assigned-clocks = <&gcc USB_HS3_XCVR_CLK>; |
| assigned-clock-rates = <60000000>; |
| resets = <&gcc USB_HS3_RESET>; |
| reset-names = "core"; |
| phy_type = "ulpi"; |
| ahb-burst-config = <0>; |
| phys = <&usb_hs3_phy>; |
| phy-names = "usb-phy"; |
| status = "disabled"; |
| #reset-cells = <1>; |
| |
| ulpi { |
| usb_hs3_phy: phy { |
| compatible = "qcom,usb-hs-phy-apq8064", |
| "qcom,usb-hs-phy"; |
| #phy-cells = <0>; |
| clocks = <&sleep_clk>, <&cxo_board>; |
| clock-names = "sleep", "ref"; |
| resets = <&usb3 0>; |
| reset-names = "por"; |
| }; |
| }; |
| }; |
| |
| usb4: usb@12530000 { |
| compatible = "qcom,ci-hdrc"; |
| reg = <0x12530000 0x200>, |
| <0x12530200 0x200>; |
| interrupts = <GIC_SPI 215 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&gcc USB_HS4_XCVR_CLK>, <&gcc USB_HS4_H_CLK>; |
| clock-names = "core", "iface"; |
| assigned-clocks = <&gcc USB_HS4_XCVR_CLK>; |
| assigned-clock-rates = <60000000>; |
| resets = <&gcc USB_HS4_RESET>; |
| reset-names = "core"; |
| phy_type = "ulpi"; |
| ahb-burst-config = <0>; |
| phys = <&usb_hs4_phy>; |
| phy-names = "usb-phy"; |
| status = "disabled"; |
| #reset-cells = <1>; |
| |
| ulpi { |
| usb_hs4_phy: phy { |
| compatible = "qcom,usb-hs-phy-apq8064", |
| "qcom,usb-hs-phy"; |
| #phy-cells = <0>; |
| clocks = <&sleep_clk>, <&cxo_board>; |
| clock-names = "sleep", "ref"; |
| resets = <&usb4 0>; |
| reset-names = "por"; |
| }; |
| }; |
| }; |
| |
| sata_phy0: phy@1b400000 { |
| compatible = "qcom,apq8064-sata-phy"; |
| status = "disabled"; |
| reg = <0x1b400000 0x200>; |
| reg-names = "phy_mem"; |
| clocks = <&gcc SATA_PHY_CFG_CLK>; |
| clock-names = "cfg"; |
| #phy-cells = <0>; |
| }; |
| |
| sata0: sata@29000000 { |
| compatible = "qcom,apq8064-ahci", "generic-ahci"; |
| status = "disabled"; |
| reg = <0x29000000 0x180>; |
| interrupts = <GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH>; |
| |
| clocks = <&gcc SFAB_SATA_S_H_CLK>, |
| <&gcc SATA_H_CLK>, |
| <&gcc SATA_A_CLK>, |
| <&gcc SATA_RXOOB_CLK>, |
| <&gcc SATA_PMALIVE_CLK>; |
| clock-names = "slave_iface", |
| "iface", |
| "bus", |
| "rxoob", |
| "core_pmalive"; |
| |
| assigned-clocks = <&gcc SATA_RXOOB_CLK>, |
| <&gcc SATA_PMALIVE_CLK>; |
| assigned-clock-rates = <100000000>, <100000000>; |
| |
| phys = <&sata_phy0>; |
| phy-names = "sata-phy"; |
| ports-implemented = <0x1>; |
| }; |
| |
| sdcc3: mmc@12180000 { |
| compatible = "arm,pl18x", "arm,primecell"; |
| arm,primecell-periphid = <0x00051180>; |
| status = "disabled"; |
| reg = <0x12180000 0x2000>; |
| interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&gcc SDC3_CLK>, <&gcc SDC3_H_CLK>; |
| clock-names = "mclk", "apb_pclk"; |
| bus-width = <4>; |
| cap-sd-highspeed; |
| cap-mmc-highspeed; |
| max-frequency = <192000000>; |
| no-1-8-v; |
| dmas = <&sdcc3bam 2>, <&sdcc3bam 1>; |
| dma-names = "tx", "rx"; |
| }; |
| |
| sdcc3bam: dma-controller@12182000 { |
| compatible = "qcom,bam-v1.3.0"; |
| reg = <0x12182000 0x8000>; |
| interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&gcc SDC3_H_CLK>; |
| clock-names = "bam_clk"; |
| #dma-cells = <1>; |
| qcom,ee = <0>; |
| }; |
| |
| sdcc4: mmc@121c0000 { |
| compatible = "arm,pl18x", "arm,primecell"; |
| arm,primecell-periphid = <0x00051180>; |
| status = "disabled"; |
| reg = <0x121c0000 0x2000>; |
| interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&gcc SDC4_CLK>, <&gcc SDC4_H_CLK>; |
| clock-names = "mclk", "apb_pclk"; |
| bus-width = <4>; |
| cap-sd-highspeed; |
| cap-mmc-highspeed; |
| max-frequency = <48000000>; |
| dmas = <&sdcc4bam 2>, <&sdcc4bam 1>; |
| dma-names = "tx", "rx"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&sdc4_gpios>; |
| }; |
| |
| sdcc4bam: dma-controller@121c2000 { |
| compatible = "qcom,bam-v1.3.0"; |
| reg = <0x121c2000 0x8000>; |
| interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&gcc SDC4_H_CLK>; |
| clock-names = "bam_clk"; |
| #dma-cells = <1>; |
| qcom,ee = <0>; |
| }; |
| |
| sdcc1: mmc@12400000 { |
| status = "disabled"; |
| compatible = "arm,pl18x", "arm,primecell"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&sdcc1_pins>; |
| arm,primecell-periphid = <0x00051180>; |
| reg = <0x12400000 0x2000>; |
| interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&gcc SDC1_CLK>, <&gcc SDC1_H_CLK>; |
| clock-names = "mclk", "apb_pclk"; |
| bus-width = <8>; |
| max-frequency = <96000000>; |
| non-removable; |
| cap-sd-highspeed; |
| cap-mmc-highspeed; |
| dmas = <&sdcc1bam 2>, <&sdcc1bam 1>; |
| dma-names = "tx", "rx"; |
| }; |
| |
| sdcc1bam: dma-controller@12402000 { |
| compatible = "qcom,bam-v1.3.0"; |
| reg = <0x12402000 0x8000>; |
| interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&gcc SDC1_H_CLK>; |
| clock-names = "bam_clk"; |
| #dma-cells = <1>; |
| qcom,ee = <0>; |
| }; |
| |
| tcsr: syscon@1a400000 { |
| compatible = "qcom,tcsr-apq8064", "syscon"; |
| reg = <0x1a400000 0x100>; |
| }; |
| |
| gpu: gpu@4300000 { |
| compatible = "qcom,adreno-320.2", "qcom,adreno"; |
| reg = <0x04300000 0x20000>; |
| reg-names = "kgsl_3d0_reg_memory"; |
| interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "kgsl_3d0_irq"; |
| clock-names = |
| "core", |
| "iface", |
| "mem", |
| "mem_iface"; |
| clocks = |
| <&mmcc GFX3D_CLK>, |
| <&mmcc GFX3D_AHB_CLK>, |
| <&mmcc GFX3D_AXI_CLK>, |
| <&mmcc MMSS_IMEM_AHB_CLK>; |
| |
| iommus = <&gfx3d 0 |
| &gfx3d 1 |
| &gfx3d 2 |
| &gfx3d 3 |
| &gfx3d 4 |
| &gfx3d 5 |
| &gfx3d 6 |
| &gfx3d 7 |
| &gfx3d 8 |
| &gfx3d 9 |
| &gfx3d 10 |
| &gfx3d 11 |
| &gfx3d 12 |
| &gfx3d 13 |
| &gfx3d 14 |
| &gfx3d 15 |
| &gfx3d 16 |
| &gfx3d 17 |
| &gfx3d 18 |
| &gfx3d 19 |
| &gfx3d 20 |
| &gfx3d 21 |
| &gfx3d 22 |
| &gfx3d 23 |
| &gfx3d 24 |
| &gfx3d 25 |
| &gfx3d 26 |
| &gfx3d 27 |
| &gfx3d 28 |
| &gfx3d 29 |
| &gfx3d 30 |
| &gfx3d 31 |
| &gfx3d1 0 |
| &gfx3d1 1 |
| &gfx3d1 2 |
| &gfx3d1 3 |
| &gfx3d1 4 |
| &gfx3d1 5 |
| &gfx3d1 6 |
| &gfx3d1 7 |
| &gfx3d1 8 |
| &gfx3d1 9 |
| &gfx3d1 10 |
| &gfx3d1 11 |
| &gfx3d1 12 |
| &gfx3d1 13 |
| &gfx3d1 14 |
| &gfx3d1 15 |
| &gfx3d1 16 |
| &gfx3d1 17 |
| &gfx3d1 18 |
| &gfx3d1 19 |
| &gfx3d1 20 |
| &gfx3d1 21 |
| &gfx3d1 22 |
| &gfx3d1 23 |
| &gfx3d1 24 |
| &gfx3d1 25 |
| &gfx3d1 26 |
| &gfx3d1 27 |
| &gfx3d1 28 |
| &gfx3d1 29 |
| &gfx3d1 30 |
| &gfx3d1 31>; |
| |
| operating-points-v2 = <&gpu_opp_table>; |
| |
| gpu_opp_table: opp-table { |
| compatible = "operating-points-v2"; |
| |
| opp-450000000 { |
| opp-hz = /bits/ 64 <450000000>; |
| }; |
| |
| opp-27000000 { |
| opp-hz = /bits/ 64 <27000000>; |
| }; |
| }; |
| }; |
| |
| mmss_sfpb: syscon@5700000 { |
| compatible = "syscon"; |
| reg = <0x5700000 0x70>; |
| }; |
| |
| dsi0: dsi@4700000 { |
| compatible = "qcom,apq8064-dsi-ctrl", |
| "qcom,mdss-dsi-ctrl"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>; |
| reg = <0x04700000 0x200>; |
| reg-names = "dsi_ctrl"; |
| |
| clocks = <&mmcc DSI_M_AHB_CLK>, |
| <&mmcc DSI_S_AHB_CLK>, |
| <&mmcc AMP_AHB_CLK>, |
| <&mmcc DSI_CLK>, |
| <&mmcc DSI1_BYTE_CLK>, |
| <&mmcc DSI_PIXEL_CLK>, |
| <&mmcc DSI1_ESC_CLK>; |
| clock-names = "iface", "bus", "core_mmss", |
| "src", "byte", "pixel", |
| "core"; |
| |
| assigned-clocks = <&mmcc DSI1_BYTE_SRC>, |
| <&mmcc DSI1_ESC_SRC>, |
| <&mmcc DSI_SRC>, |
| <&mmcc DSI_PIXEL_SRC>; |
| assigned-clock-parents = <&dsi0_phy 0>, |
| <&dsi0_phy 0>, |
| <&dsi0_phy 1>, |
| <&dsi0_phy 1>; |
| syscon-sfpb = <&mmss_sfpb>; |
| phys = <&dsi0_phy>; |
| status = "disabled"; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| dsi0_in: endpoint { |
| }; |
| }; |
| |
| port@1 { |
| reg = <1>; |
| dsi0_out: endpoint { |
| }; |
| }; |
| }; |
| }; |
| |
| |
| dsi0_phy: phy@4700200 { |
| compatible = "qcom,dsi-phy-28nm-8960"; |
| #clock-cells = <1>; |
| #phy-cells = <0>; |
| |
| reg = <0x04700200 0x100>, |
| <0x04700300 0x200>, |
| <0x04700500 0x5c>; |
| reg-names = "dsi_pll", "dsi_phy", "dsi_phy_regulator"; |
| clock-names = "iface", "ref"; |
| clocks = <&mmcc DSI_M_AHB_CLK>, |
| <&pxo_board>; |
| status = "disabled"; |
| }; |
| |
| dsi1: dsi@5800000 { |
| compatible = "qcom,mdss-dsi-ctrl"; |
| interrupts = <GIC_SPI 166 IRQ_TYPE_LEVEL_HIGH>; |
| reg = <0x05800000 0x200>; |
| reg-names = "dsi_ctrl"; |
| |
| clocks = <&mmcc DSI2_M_AHB_CLK>, |
| <&mmcc DSI2_S_AHB_CLK>, |
| <&mmcc AMP_AHB_CLK>, |
| <&mmcc DSI2_CLK>, |
| <&mmcc DSI2_BYTE_CLK>, |
| <&mmcc DSI2_PIXEL_CLK>, |
| <&mmcc DSI2_ESC_CLK>; |
| clock-names = "iface", |
| "bus", |
| "core_mmss", |
| "src", |
| "byte", |
| "pixel", |
| "core"; |
| |
| assigned-clocks = <&mmcc DSI2_BYTE_SRC>, |
| <&mmcc DSI2_ESC_SRC>, |
| <&mmcc DSI2_SRC>, |
| <&mmcc DSI2_PIXEL_SRC>; |
| assigned-clock-parents = <&dsi1_phy 0>, |
| <&dsi1_phy 0>, |
| <&dsi1_phy 1>, |
| <&dsi1_phy 1>; |
| |
| syscon-sfpb = <&mmss_sfpb>; |
| phys = <&dsi1_phy>; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| status = "disabled"; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| dsi1_in: endpoint { |
| }; |
| }; |
| |
| port@1 { |
| reg = <1>; |
| dsi1_out: endpoint { |
| }; |
| }; |
| }; |
| }; |
| |
| |
| dsi1_phy: dsi-phy@5800200 { |
| compatible = "qcom,dsi-phy-28nm-8960"; |
| reg = <0x05800200 0x100>, |
| <0x05800300 0x200>, |
| <0x05800500 0x5c>; |
| reg-names = "dsi_pll", |
| "dsi_phy", |
| "dsi_phy_regulator"; |
| clock-names = "iface", |
| "ref"; |
| clocks = <&mmcc DSI2_M_AHB_CLK>, |
| <&pxo_board>; |
| #clock-cells = <1>; |
| #phy-cells = <0>; |
| |
| status = "disabled"; |
| }; |
| |
| mdp_port0: iommu@7500000 { |
| compatible = "qcom,apq8064-iommu"; |
| #iommu-cells = <1>; |
| clock-names = |
| "smmu_pclk", |
| "iommu_clk"; |
| clocks = |
| <&mmcc SMMU_AHB_CLK>, |
| <&mmcc MDP_AXI_CLK>; |
| reg = <0x07500000 0x100000>; |
| interrupts = |
| <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>; |
| qcom,ncb = <2>; |
| }; |
| |
| mdp_port1: iommu@7600000 { |
| compatible = "qcom,apq8064-iommu"; |
| #iommu-cells = <1>; |
| clock-names = |
| "smmu_pclk", |
| "iommu_clk"; |
| clocks = |
| <&mmcc SMMU_AHB_CLK>, |
| <&mmcc MDP_AXI_CLK>; |
| reg = <0x07600000 0x100000>; |
| interrupts = |
| <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>; |
| qcom,ncb = <2>; |
| }; |
| |
| gfx3d: iommu@7c00000 { |
| compatible = "qcom,apq8064-iommu"; |
| #iommu-cells = <1>; |
| clock-names = |
| "smmu_pclk", |
| "iommu_clk"; |
| clocks = |
| <&mmcc SMMU_AHB_CLK>, |
| <&mmcc GFX3D_AXI_CLK>; |
| reg = <0x07c00000 0x100000>; |
| interrupts = |
| <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>; |
| qcom,ncb = <3>; |
| }; |
| |
| gfx3d1: iommu@7d00000 { |
| compatible = "qcom,apq8064-iommu"; |
| #iommu-cells = <1>; |
| clock-names = |
| "smmu_pclk", |
| "iommu_clk"; |
| clocks = |
| <&mmcc SMMU_AHB_CLK>, |
| <&mmcc GFX3D_AXI_CLK>; |
| reg = <0x07d00000 0x100000>; |
| interrupts = |
| <GIC_SPI 210 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 211 IRQ_TYPE_LEVEL_HIGH>; |
| qcom,ncb = <3>; |
| }; |
| |
| pcie: pcie@1b500000 { |
| compatible = "qcom,pcie-apq8064"; |
| reg = <0x1b500000 0x1000>, |
| <0x1b502000 0x80>, |
| <0x1b600000 0x100>, |
| <0x0ff00000 0x100000>; |
| reg-names = "dbi", "elbi", "parf", "config"; |
| device_type = "pci"; |
| linux,pci-domain = <0>; |
| bus-range = <0x00 0xff>; |
| num-lanes = <1>; |
| #address-cells = <3>; |
| #size-cells = <2>; |
| ranges = <0x81000000 0x0 0x00000000 0x0fe00000 0x0 0x00100000>, /* I/O */ |
| <0x82000000 0x0 0x08000000 0x08000000 0x0 0x07e00000>; /* mem */ |
| interrupts = <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "msi"; |
| #interrupt-cells = <1>; |
| interrupt-map-mask = <0 0 0 0x7>; |
| interrupt-map = <0 0 0 1 &intc 0 36 IRQ_TYPE_LEVEL_HIGH>, /* int_a */ |
| <0 0 0 2 &intc 0 37 IRQ_TYPE_LEVEL_HIGH>, /* int_b */ |
| <0 0 0 3 &intc 0 38 IRQ_TYPE_LEVEL_HIGH>, /* int_c */ |
| <0 0 0 4 &intc 0 39 IRQ_TYPE_LEVEL_HIGH>; /* int_d */ |
| clocks = <&gcc PCIE_A_CLK>, |
| <&gcc PCIE_H_CLK>, |
| <&gcc PCIE_PHY_REF_CLK>; |
| clock-names = "core", "iface", "phy"; |
| resets = <&gcc PCIE_ACLK_RESET>, |
| <&gcc PCIE_HCLK_RESET>, |
| <&gcc PCIE_POR_RESET>, |
| <&gcc PCIE_PCI_RESET>, |
| <&gcc PCIE_PHY_RESET>; |
| reset-names = "axi", "ahb", "por", "pci", "phy"; |
| status = "disabled"; |
| |
| pcie@0 { |
| device_type = "pci"; |
| reg = <0x0 0x0 0x0 0x0 0x0>; |
| bus-range = <0x01 0xff>; |
| |
| #address-cells = <3>; |
| #size-cells = <2>; |
| ranges; |
| }; |
| }; |
| |
| hdmi: hdmi-tx@4a00000 { |
| compatible = "qcom,hdmi-tx-8960"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&hdmi_pinctrl>; |
| reg = <0x04a00000 0x2f0>; |
| reg-names = "core_physical"; |
| interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&mmcc HDMI_APP_CLK>, |
| <&mmcc HDMI_M_AHB_CLK>, |
| <&mmcc HDMI_S_AHB_CLK>; |
| clock-names = "core", |
| "master_iface", |
| "slave_iface"; |
| |
| phys = <&hdmi_phy>; |
| |
| status = "disabled"; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| hdmi_in: endpoint { |
| }; |
| }; |
| |
| port@1 { |
| reg = <1>; |
| hdmi_out: endpoint { |
| }; |
| }; |
| }; |
| }; |
| |
| hdmi_phy: phy@4a00400 { |
| compatible = "qcom,hdmi-phy-8960"; |
| reg = <0x4a00400 0x60>, |
| <0x4a00500 0x100>; |
| reg-names = "hdmi_phy", |
| "hdmi_pll"; |
| |
| clocks = <&mmcc HDMI_S_AHB_CLK>; |
| clock-names = "slave_iface"; |
| #phy-cells = <0>; |
| #clock-cells = <0>; |
| |
| status = "disabled"; |
| }; |
| |
| mdp: display-controller@5100000 { |
| compatible = "qcom,mdp4"; |
| reg = <0x05100000 0xf0000>; |
| interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&mmcc MDP_CLK>, |
| <&mmcc MDP_AHB_CLK>, |
| <&mmcc MDP_AXI_CLK>, |
| <&mmcc MDP_LUT_CLK>, |
| <&mmcc HDMI_TV_CLK>, |
| <&mmcc MDP_TV_CLK>; |
| clock-names = "core_clk", |
| "iface_clk", |
| "bus_clk", |
| "lut_clk", |
| "hdmi_clk", |
| "tv_clk"; |
| |
| iommus = <&mdp_port0 0 |
| &mdp_port0 2 |
| &mdp_port1 0 |
| &mdp_port1 2>; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| mdp_lvds_out: endpoint { |
| }; |
| }; |
| |
| port@1 { |
| reg = <1>; |
| mdp_dsi1_out: endpoint { |
| }; |
| }; |
| |
| port@2 { |
| reg = <2>; |
| mdp_dsi2_out: endpoint { |
| }; |
| }; |
| |
| port@3 { |
| reg = <3>; |
| mdp_dtv_out: endpoint { |
| }; |
| }; |
| }; |
| }; |
| |
| riva: riva-pil@3200800 { |
| compatible = "qcom,riva-pil"; |
| |
| reg = <0x03200800 0x1000>, <0x03202000 0x2000>, <0x03204000 0x100>; |
| reg-names = "ccu", "dxe", "pmu"; |
| |
| interrupts-extended = <&intc GIC_SPI 199 IRQ_TYPE_EDGE_RISING>, |
| <&wcnss_smsm 6 IRQ_TYPE_EDGE_RISING>; |
| interrupt-names = "wdog", "fatal"; |
| |
| memory-region = <&wcnss_mem>; |
| |
| status = "disabled"; |
| |
| iris { |
| compatible = "qcom,wcn3660"; |
| |
| clocks = <&cxo_board>; |
| clock-names = "xo"; |
| }; |
| |
| smd-edge { |
| interrupts = <GIC_SPI 198 IRQ_TYPE_EDGE_RISING>; |
| |
| qcom,ipc = <&l2cc 8 25>; |
| qcom,smd-edge = <6>; |
| |
| label = "riva"; |
| |
| wcnss { |
| compatible = "qcom,wcnss"; |
| qcom,smd-channels = "WCNSS_CTRL"; |
| |
| qcom,mmio = <&riva>; |
| |
| bluetooth { |
| compatible = "qcom,wcnss-bt"; |
| }; |
| |
| wifi { |
| compatible = "qcom,wcnss-wlan"; |
| |
| interrupts = <GIC_SPI 203 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 202 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "tx", "rx"; |
| |
| qcom,smem-states = <&apps_smsm 10>, <&apps_smsm 9>; |
| qcom,smem-state-names = "tx-enable", "tx-rings-empty"; |
| }; |
| }; |
| }; |
| }; |
| |
| etb@1a01000 { |
| compatible = "arm,coresight-etb10", "arm,primecell"; |
| reg = <0x1a01000 0x1000>; |
| |
| clocks = <&rpmcc RPM_QDSS_CLK>; |
| clock-names = "apb_pclk"; |
| |
| in-ports { |
| port { |
| etb_in: endpoint { |
| remote-endpoint = <&replicator_out0>; |
| }; |
| }; |
| }; |
| }; |
| |
| tpiu@1a03000 { |
| compatible = "arm,coresight-tpiu", "arm,primecell"; |
| reg = <0x1a03000 0x1000>; |
| |
| clocks = <&rpmcc RPM_QDSS_CLK>; |
| clock-names = "apb_pclk"; |
| |
| in-ports { |
| port { |
| tpiu_in: endpoint { |
| remote-endpoint = <&replicator_out1>; |
| }; |
| }; |
| }; |
| }; |
| |
| replicator { |
| compatible = "arm,coresight-static-replicator"; |
| |
| clocks = <&rpmcc RPM_QDSS_CLK>; |
| clock-names = "apb_pclk"; |
| |
| out-ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| replicator_out0: endpoint { |
| remote-endpoint = <&etb_in>; |
| }; |
| }; |
| port@1 { |
| reg = <1>; |
| replicator_out1: endpoint { |
| remote-endpoint = <&tpiu_in>; |
| }; |
| }; |
| }; |
| |
| in-ports { |
| port { |
| replicator_in: endpoint { |
| remote-endpoint = <&funnel_out>; |
| }; |
| }; |
| }; |
| }; |
| |
| funnel@1a04000 { |
| compatible = "arm,coresight-dynamic-funnel", "arm,primecell"; |
| reg = <0x1a04000 0x1000>; |
| |
| clocks = <&rpmcc RPM_QDSS_CLK>; |
| clock-names = "apb_pclk"; |
| |
| in-ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| /* |
| * Not described input ports: |
| * 2 - connected to STM component |
| * 3 - not-connected |
| * 6 - not-connected |
| * 7 - not-connected |
| */ |
| port@0 { |
| reg = <0>; |
| funnel_in0: endpoint { |
| remote-endpoint = <&etm0_out>; |
| }; |
| }; |
| port@1 { |
| reg = <1>; |
| funnel_in1: endpoint { |
| remote-endpoint = <&etm1_out>; |
| }; |
| }; |
| port@4 { |
| reg = <4>; |
| funnel_in4: endpoint { |
| remote-endpoint = <&etm2_out>; |
| }; |
| }; |
| port@5 { |
| reg = <5>; |
| funnel_in5: endpoint { |
| remote-endpoint = <&etm3_out>; |
| }; |
| }; |
| }; |
| |
| out-ports { |
| port { |
| funnel_out: endpoint { |
| remote-endpoint = <&replicator_in>; |
| }; |
| }; |
| }; |
| }; |
| |
| etm@1a1c000 { |
| compatible = "arm,coresight-etm3x", "arm,primecell"; |
| reg = <0x1a1c000 0x1000>; |
| |
| clocks = <&rpmcc RPM_QDSS_CLK>; |
| clock-names = "apb_pclk"; |
| |
| cpu = <&CPU0>; |
| |
| out-ports { |
| port { |
| etm0_out: endpoint { |
| remote-endpoint = <&funnel_in0>; |
| }; |
| }; |
| }; |
| }; |
| |
| etm@1a1d000 { |
| compatible = "arm,coresight-etm3x", "arm,primecell"; |
| reg = <0x1a1d000 0x1000>; |
| |
| clocks = <&rpmcc RPM_QDSS_CLK>; |
| clock-names = "apb_pclk"; |
| |
| cpu = <&CPU1>; |
| |
| out-ports { |
| port { |
| etm1_out: endpoint { |
| remote-endpoint = <&funnel_in1>; |
| }; |
| }; |
| }; |
| }; |
| |
| etm@1a1e000 { |
| compatible = "arm,coresight-etm3x", "arm,primecell"; |
| reg = <0x1a1e000 0x1000>; |
| |
| clocks = <&rpmcc RPM_QDSS_CLK>; |
| clock-names = "apb_pclk"; |
| |
| cpu = <&CPU2>; |
| |
| out-ports { |
| port { |
| etm2_out: endpoint { |
| remote-endpoint = <&funnel_in4>; |
| }; |
| }; |
| }; |
| }; |
| |
| etm@1a1f000 { |
| compatible = "arm,coresight-etm3x", "arm,primecell"; |
| reg = <0x1a1f000 0x1000>; |
| |
| clocks = <&rpmcc RPM_QDSS_CLK>; |
| clock-names = "apb_pclk"; |
| |
| cpu = <&CPU3>; |
| |
| out-ports { |
| port { |
| etm3_out: endpoint { |
| remote-endpoint = <&funnel_in5>; |
| }; |
| }; |
| }; |
| }; |
| }; |
| }; |
| #include "qcom-apq8064-pins.dtsi" |