| // SPDX-License-Identifier: GPL-2.0 |
| /* |
| * Samsung's Exynos4412 based p4note device family base DT. |
| * Based on exynos4412-midas.dtsi. |
| * |
| * Copyright (c) 2013 Samsung Electronics Co., Ltd. |
| * http://www.samsung.com |
| */ |
| |
| /dts-v1/; |
| #include "exynos4412.dtsi" |
| #include "exynos4412-ppmu-common.dtsi" |
| |
| #include <dt-bindings/clock/maxim,max77686.h> |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/input/linux-event-codes.h> |
| #include <dt-bindings/interrupt-controller/irq.h> |
| #include <dt-bindings/power/summit,smb347-charger.h> |
| #include "exynos-pinctrl.h" |
| |
| / { |
| compatible = "samsung,p4note", "samsung,exynos4412", "samsung,exynos4"; |
| |
| memory@40000000 { |
| device_type = "memory"; |
| reg = <0x40000000 0x7fc00000>; |
| }; |
| |
| aliases { |
| mmc0 = &mshc_0; |
| mmc2 = &sdhci_2; |
| mmc3 = &sdhci_3; |
| }; |
| |
| chosen { |
| stdout-path = &serial_2; |
| }; |
| |
| firmware@204f000 { |
| compatible = "samsung,secure-firmware"; |
| reg = <0x0204f000 0x1000>; |
| }; |
| |
| fixed-rate-clocks { |
| xxti { |
| compatible = "samsung,clock-xxti"; |
| clock-frequency = <0>; |
| }; |
| |
| xusbxti { |
| compatible = "samsung,clock-xusbxti"; |
| clock-frequency = <24000000>; |
| }; |
| }; |
| |
| gpio-keys { |
| compatible = "gpio-keys"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&gpio_keys>; |
| |
| key-down { |
| gpios = <&gpx2 2 GPIO_ACTIVE_LOW>; |
| linux,code = <KEY_VOLUMEDOWN>; |
| label = "volume down"; |
| debounce-interval = <10>; |
| }; |
| |
| key-up { |
| gpios = <&gpx3 3 GPIO_ACTIVE_LOW>; |
| linux,code = <KEY_VOLUMEUP>; |
| label = "volume up"; |
| debounce-interval = <10>; |
| }; |
| |
| key-power { |
| gpios = <&gpx2 7 GPIO_ACTIVE_LOW>; |
| linux,code = <KEY_POWER>; |
| label = "power"; |
| debounce-interval = <10>; |
| wakeup-source; |
| }; |
| }; |
| |
| voltage-regulator-1 { |
| compatible = "regulator-fixed"; |
| regulator-name = "TSP_LDO1"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&tsp_reg_gpio_1>; |
| gpios = <&gpm4 5 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| regulator-always-on; |
| }; |
| |
| voltage-regulator-2 { |
| compatible = "regulator-fixed"; |
| regulator-name = "TSP_LDO2"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&tsp_reg_gpio_2>; |
| gpios = <&gpb 5 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| regulator-always-on; |
| }; |
| |
| voltage-regulator-3 { |
| compatible = "regulator-fixed"; |
| regulator-name = "TSP_LDO3"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&tsp_reg_gpio_3>; |
| gpios = <&gpb 7 GPIO_ACTIVE_HIGH>; |
| startup-delay-us = <20000>; |
| enable-active-high; |
| regulator-always-on; |
| }; |
| |
| panel_vdd: voltage-regulator-4 { |
| compatible = "regulator-fixed"; |
| regulator-name = "LCD_ENABLE"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&lcd_enable>; |
| gpios = <&gpc0 1 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| regulator-boot-on; |
| }; |
| |
| wlan_pwrseq: sdhci3-pwrseq { |
| compatible = "mmc-pwrseq-simple"; |
| reset-gpios = <&gpm3 5 GPIO_ACTIVE_LOW>; |
| pinctrl-0 = <&wifi_reset>; |
| pinctrl-names = "default"; |
| clocks = <&max77686 MAX77686_CLK_PMIC>; |
| clock-names = "ext_clock"; |
| }; |
| |
| battery_cell: battery-cell { |
| compatible = "simple-battery"; |
| device-chemistry = "lithium-ion"; |
| constant-charge-current-max-microamp = <2200000>; |
| precharge-current-microamp = <250000>; |
| charge-term-current-microamp = <250000>; |
| constant-charge-voltage-max-microvolt = <4200000>; |
| }; |
| |
| i2c-gpio-1 { |
| compatible = "i2c-gpio"; |
| sda-gpios = <&gpy2 4 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| scl-gpios = <&gpy2 5 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| i2c-gpio,delay-us = <2>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| magnetometer@c { |
| compatible = "asahi-kasei,ak8975"; |
| reg = <0x0c>; |
| pinctrl-0 = <&ak8975_irq>; |
| pinctrl-names = "default"; |
| interrupt-parent = <&gpm4>; |
| interrupts = <7 IRQ_TYPE_EDGE_RISING>; |
| }; |
| }; |
| |
| i2c-gpio-2 { |
| compatible = "i2c-gpio"; |
| sda-gpios = <&gpy0 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| scl-gpios = <&gpy0 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| i2c-gpio,delay-us = <2>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| fuel-gauge@36 { |
| compatible = "maxim,max17042"; |
| reg = <0x36>; |
| pinctrl-0 = <&fuel_alert_irq>; |
| pinctrl-names = "default"; |
| interrupt-parent = <&gpx2>; |
| interrupts = <3 IRQ_TYPE_LEVEL_LOW>; |
| maxim,rsns-microohm = <10000>; |
| maxim,over-heat-temp = <600>; |
| maxim,over-volt = <4300>; |
| }; |
| }; |
| |
| i2c-gpio-3 { |
| compatible = "i2c-gpio"; |
| sda-gpios = <&gpm4 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| scl-gpios = <&gpm4 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| i2c-gpio,delay-us = <5>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| adc@41 { |
| compatible = "st,stmpe811"; |
| reg = <0x41>; |
| pinctrl-0 = <&stmpe_adc_irq>; |
| pinctrl-names = "default"; |
| interrupt-parent = <&gpx0>; |
| interrupts = <1 IRQ_TYPE_LEVEL_LOW>; |
| st,adc-freq = <3>; |
| st,mod-12b = <1>; |
| st,ref-sel = <0>; |
| st,sample-time = <3>; |
| |
| adc { |
| compatible = "st,stmpe-adc"; |
| #io-channel-cells = <1>; |
| st,norequest-mask = <0x2f>; |
| }; |
| }; |
| }; |
| |
| i2c-gpio-4 { |
| compatible = "i2c-gpio"; |
| sda-gpios = <&gpm2 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| scl-gpios = <&gpm2 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| |
| i2c-gpio,delay-us = <2>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| power_supply: charger@6 { |
| compatible = "summit,smb347"; |
| reg = <0x6>; |
| summit,enable-usb-charging; |
| summit,enable-charge-control = <SMB3XX_CHG_ENABLE_SW>; |
| summit,fast-voltage-threshold-microvolt = <2600000>; |
| summit,chip-temperature-threshold-celsius = <130>; |
| summit,usb-current-limit-microamp = <1800000>; |
| |
| monitored-battery = <&battery_cell>; |
| }; |
| }; |
| |
| panel { |
| compatible = "samsung,ltl101al01"; |
| pinctrl-0 = <&lvds_nshdn>; |
| pinctrl-names = "default"; |
| power-supply = <&panel_vdd>; |
| enable-gpios = <&gpm0 5 GPIO_ACTIVE_HIGH>; |
| backlight = <&backlight>; |
| |
| port { |
| lcd_ep: endpoint { |
| remote-endpoint = <&fimd_ep>; |
| }; |
| }; |
| }; |
| |
| backlight: backlight { |
| compatible = "pwm-backlight"; |
| pinctrl-0 = <&led_bl_reset>; |
| pinctrl-names = "default"; |
| enable-gpios = <&gpm0 1 GPIO_ACTIVE_HIGH>; |
| power-supply = <&panel_vdd>; |
| pwms = <&pwm 1 78770 0>; |
| brightness-levels = <0 48 128 255>; |
| num-interpolated-steps = <8>; |
| default-brightness-level = <12>; |
| }; |
| }; |
| |
| &adc { |
| vdd-supply = <&ldo3_reg>; |
| /* not verified */ |
| status = "okay"; |
| }; |
| |
| &bus_dmc { |
| devfreq-events = <&ppmu_dmc0_3>, <&ppmu_dmc1_3>; |
| vdd-supply = <&buck1_reg>; |
| status = "okay"; |
| }; |
| |
| &bus_acp { |
| devfreq = <&bus_dmc>; |
| status = "okay"; |
| }; |
| |
| &bus_c2c { |
| devfreq = <&bus_dmc>; |
| status = "okay"; |
| }; |
| |
| &bus_leftbus { |
| devfreq-events = <&ppmu_leftbus_3>, <&ppmu_rightbus_3>; |
| vdd-supply = <&buck3_reg>; |
| status = "okay"; |
| }; |
| |
| &bus_rightbus { |
| devfreq = <&bus_leftbus>; |
| status = "okay"; |
| }; |
| |
| &bus_display { |
| devfreq = <&bus_leftbus>; |
| status = "okay"; |
| }; |
| |
| &bus_fsys { |
| devfreq = <&bus_leftbus>; |
| status = "okay"; |
| }; |
| |
| &bus_peri { |
| devfreq = <&bus_leftbus>; |
| status = "okay"; |
| }; |
| |
| &bus_mfc { |
| devfreq = <&bus_leftbus>; |
| status = "okay"; |
| }; |
| |
| &cpu0 { |
| cpu0-supply = <&buck2_reg>; |
| }; |
| |
| &cpu_thermal { |
| cooling-maps { |
| map0 { |
| /* Corresponds to 800MHz at freq_table */ |
| cooling-device = <&cpu0 7 7>, <&cpu1 7 7>, |
| <&cpu2 7 7>, <&cpu3 7 7>; |
| }; |
| map1 { |
| /* Corresponds to 200MHz at freq_table */ |
| cooling-device = <&cpu0 13 13>, <&cpu1 13 13>, |
| <&cpu2 13 13>, <&cpu3 13 13>; |
| }; |
| }; |
| }; |
| |
| &exynos_usbphy { |
| status = "okay"; |
| }; |
| |
| &fimd { |
| pinctrl-0 = <&lcd_clk &lcd_data24>; |
| pinctrl-names = "default"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "okay"; |
| |
| samsung,invert-vclk; |
| |
| port@3 { |
| reg = <3>; |
| |
| fimd_ep: endpoint { |
| remote-endpoint = <&lcd_ep>; |
| }; |
| }; |
| }; |
| |
| &gpu { |
| mali-supply = <&buck4_reg>; |
| status = "okay"; |
| }; |
| |
| &hsotg { |
| vusb_a-supply = <&ldo12_reg>; |
| dr_mode = "peripheral"; |
| status = "okay"; |
| }; |
| |
| &i2c_1 { |
| samsung,i2c-sda-delay = <100>; |
| samsung,i2c-slave-addr = <0x10>; |
| samsung,i2c-max-bus-freq = <400000>; |
| pinctrl-0 = <&i2c1_bus>; |
| pinctrl-names = "default"; |
| status = "okay"; |
| |
| accelerometer@19 { |
| compatible = "st,lsm330dlc-accel"; |
| reg = <0x19>; |
| interrupt-parent = <&gpx0>; |
| interrupts = <0 IRQ_TYPE_EDGE_RISING>; |
| pinctrl-0 = <&accelerometer_irq>; |
| pinctrl-names = "default"; |
| mount-matrix = "1", "0", "0", |
| "0", "-1", "0", |
| "0", "0", "-1"; |
| }; |
| |
| gyro@6b { |
| compatible = "st,lsm330dlc-gyro"; |
| reg = <0x6b>; |
| interrupt-parent = <&gpx0>; |
| interrupts = <6 IRQ_TYPE_EDGE_RISING>; |
| pinctrl-0 = <&gyro_data_enable &gyro_irq>; |
| pinctrl-names = "default"; |
| mount-matrix = "1", "0", "0", |
| "0", "-1", "0", |
| "0", "0", "-1"; |
| }; |
| }; |
| |
| &i2c_3 { |
| samsung,i2c-sda-delay = <100>; |
| samsung,i2c-slave-addr = <0x10>; |
| samsung,i2c-max-bus-freq = <400000>; |
| pinctrl-0 = <&i2c3_bus>; |
| pinctrl-names = "default"; |
| status = "okay"; |
| |
| touchscreen@4a { |
| compatible = "atmel,maxtouch"; |
| reg = <0x4a>; |
| pinctrl-0 = <&tsp_rst &tsp_irq>; |
| pinctrl-names = "default"; |
| interrupt-parent = <&gpm2>; |
| interrupts = <3 IRQ_TYPE_LEVEL_LOW>; |
| reset-gpios = <&gpm0 4 GPIO_ACTIVE_LOW>; |
| }; |
| }; |
| |
| &i2c_7 { |
| samsung,i2c-sda-delay = <100>; |
| samsung,i2c-slave-addr = <0x10>; |
| samsung,i2c-max-bus-freq = <400000>; |
| pinctrl-0 = <&i2c7_bus>; |
| pinctrl-names = "default"; |
| status = "okay"; |
| |
| max77686: pmic@9 { |
| compatible = "maxim,max77686"; |
| interrupt-parent = <&gpx0>; |
| interrupts = <7 IRQ_TYPE_LEVEL_LOW>; |
| pinctrl-0 = <&max77686_irq>; |
| pinctrl-names = "default"; |
| wakeup-source; |
| reg = <0x09>; |
| #clock-cells = <1>; |
| |
| voltage-regulators { |
| ldo1_reg: LDO1 { |
| regulator-name = "ldo1"; |
| regulator-always-on; |
| }; |
| |
| ldo2_reg: LDO2 { |
| regulator-name = "ldo2"; |
| regulator-always-on; |
| }; |
| |
| /* WM8994 audio */ |
| ldo3_reg: LDO3 { |
| regulator-name = "VCC_1.8V_AP"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-always-on; |
| regulator-boot-on; |
| |
| regulator-state-mem { |
| regulator-on-in-suspend; |
| }; |
| }; |
| |
| ldo4_reg: LDO4 { |
| regulator-name = "ldo4"; |
| regulator-always-on; |
| }; |
| |
| ldo5_reg: LDO5 { |
| regulator-name = "VCC_1.8V_IO"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| ldo6_reg: LDO6 { |
| regulator-name = "ldo6"; |
| regulator-always-on; |
| }; |
| |
| ldo7_reg: LDO7 { |
| regulator-name = "ldo7"; |
| regulator-always-on; |
| }; |
| |
| /* CSI IP block */ |
| ldo8_reg: LDO8 { |
| regulator-name = "VMIPI_1.0V"; |
| regulator-min-microvolt = <1000000>; |
| regulator-max-microvolt = <1000000>; |
| regulator-always-on; |
| regulator-boot-on; |
| |
| regulator-state-mem { |
| regulator-on-in-suspend; |
| }; |
| }; |
| |
| /* IR LED on/off */ |
| ldo9_reg: LDO9 { |
| regulator-name = "VLED_IC_1.9V"; |
| regulator-min-microvolt = <1950000>; |
| regulator-max-microvolt = <1950000>; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| /* CSI IP block */ |
| ldo10_reg: LDO10 { |
| regulator-name = "VMIPI_1.8V"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-always-on; |
| regulator-boot-on; |
| |
| regulator-state-mem { |
| regulator-on-in-suspend; |
| }; |
| }; |
| |
| ldo11_reg: LDO11 { |
| regulator-name = "VABB1_1.9V"; |
| regulator-min-microvolt = <1950000>; |
| regulator-max-microvolt = <1950000>; |
| regulator-always-on; |
| regulator-boot-on; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| /* USB OTG */ |
| ldo12_reg: LDO12 { |
| regulator-name = "VUOTG_3.0V"; |
| regulator-min-microvolt = <3000000>; |
| regulator-max-microvolt = <3000000>; |
| regulator-always-on; |
| regulator-boot-on; |
| |
| regulator-state-mem { |
| regulator-on-in-suspend; |
| }; |
| }; |
| |
| /* not connected */ |
| ldo13_reg: LDO13 { |
| regulator-name = "ldo13"; |
| }; |
| |
| ldo14_reg: LDO14 { |
| regulator-name = "VABB2_1.9V"; |
| regulator-min-microvolt = <1950000>; |
| regulator-max-microvolt = <1950000>; |
| regulator-always-on; |
| regulator-boot-on; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| ldo15_reg: LDO15 { |
| regulator-name = "ldo15"; |
| regulator-always-on; |
| }; |
| |
| ldo16_reg: LDO16 { |
| regulator-name = "ldo16"; |
| regulator-always-on; |
| }; |
| |
| /* not connected */ |
| ldo17_reg: LDO17 { |
| regulator-name = "ldo17"; |
| }; |
| |
| /* Camera ISX012 */ |
| ldo18_reg: LDO18 { |
| regulator-name = "CAM_IO_1.8V"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| /* Camera S5K6A3 */ |
| ldo19_reg: LDO19 { |
| regulator-name = "VT_CORE_1.8V"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| /* not connected */ |
| ldo20_reg: LDO20 { |
| regulator-name = "ldo20"; |
| }; |
| |
| /* MMC2 */ |
| ldo21_reg: LDO21 { |
| regulator-name = "VTF_2.8V"; |
| regulator-min-microvolt = <2800000>; |
| regulator-max-microvolt = <2800000>; |
| maxim,ena-gpios = <&gpy2 0 GPIO_ACTIVE_HIGH>; |
| }; |
| |
| /* not connected */ |
| ldo22_reg: LDO22 { |
| regulator-name = "ldo22"; |
| }; |
| |
| /* ADC */ |
| ldo23_reg: LDO23 { |
| regulator-name = "VDD_ADC_3.3V"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-always-on; |
| regulator-boot-on; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| /* Camera S5K6A3 */ |
| ldo24_reg: LDO24 { |
| regulator-name = "CAM_A2.8V"; |
| regulator-min-microvolt = <2800000>; |
| regulator-max-microvolt = <2800000>; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| ldo25_reg: LDO25 { |
| regulator-name = "VLED_3.3V"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| /* Camera ISX012 */ |
| ldo26_reg: LDO26 { |
| regulator-name = "3MP_AF_2.8V"; |
| regulator-min-microvolt = <2800000>; |
| regulator-max-microvolt = <2800000>; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| buck1_reg: BUCK1 { |
| regulator-name = "VDD_MIF"; |
| regulator-min-microvolt = <850000>; |
| regulator-max-microvolt = <1050000>; |
| regulator-always-on; |
| regulator-boot-on; |
| }; |
| |
| buck2_reg: BUCK2 { |
| regulator-name = "VDD_ARM"; |
| regulator-min-microvolt = <850000>; |
| regulator-max-microvolt = <1500000>; |
| regulator-always-on; |
| regulator-boot-on; |
| }; |
| |
| buck3_reg: BUCK3 { |
| regulator-name = "VDD_INT"; |
| regulator-min-microvolt = <850000>; |
| regulator-max-microvolt = <1100000>; |
| regulator-always-on; |
| regulator-boot-on; |
| }; |
| |
| buck4_reg: BUCK4 { |
| regulator-name = "VDD_G3D"; |
| regulator-min-microvolt = <850000>; |
| regulator-max-microvolt = <1075000>; |
| regulator-boot-on; |
| }; |
| |
| buck5_reg: BUCK5 { |
| regulator-name = "buck5"; |
| regulator-always-on; |
| }; |
| |
| buck6_reg: BUCK6 { |
| regulator-name = "buck6"; |
| regulator-always-on; |
| }; |
| |
| buck7_reg: BUCK7 { |
| regulator-name = "buck7"; |
| regulator-always-on; |
| }; |
| |
| /* not connected */ |
| buck8_reg: BUCK8 { |
| regulator-name = "buck8"; |
| }; |
| |
| buck9_reg: BUCK9 { |
| regulator-name = "3MP_CORE_1.2V"; |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| }; |
| }; |
| }; |
| |
| &mshc_0 { |
| broken-cd; |
| non-removable; |
| card-detect-delay = <200>; |
| clock-frequency = <400000000>; |
| samsung,dw-mshc-ciu-div = <0>; |
| samsung,dw-mshc-sdr-timing = <2 3>; |
| samsung,dw-mshc-ddr-timing = <1 2>; |
| mmc-ddr-1_8v; |
| pinctrl-0 = <&sd4_clk &sd4_cmd &sd4_bus4 &sd4_bus8>; |
| pinctrl-names = "default"; |
| bus-width = <4>; |
| cap-mmc-highspeed; |
| cap-sd-highspeed; |
| status = "okay"; |
| }; |
| |
| &pinctrl_0 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&sleep0>; |
| |
| tsp_reg_gpio_2: tsp-reg-gpio-2-pins { |
| samsung,pins = "gpb-5"; |
| samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>; |
| samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; |
| }; |
| |
| tsp_reg_gpio_3: tsp-reg-gpio-3-pins { |
| samsung,pins = "gpb-7"; |
| samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>; |
| samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; |
| }; |
| |
| lcd_enable: lcd-enable-pins { |
| samsung,pins = "gpc0-1"; |
| samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>; |
| samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; |
| }; |
| |
| sleep0: sleep-state { |
| PIN_SLP(gpa0-0, INPUT, NONE); |
| PIN_SLP(gpa0-1, OUT0, NONE); |
| PIN_SLP(gpa0-2, INPUT, NONE); |
| PIN_SLP(gpa0-3, INPUT, UP); |
| PIN_SLP(gpa0-4, INPUT, NONE); |
| PIN_SLP(gpa0-5, INPUT, DOWN); |
| PIN_SLP(gpa0-6, INPUT, DOWN); |
| PIN_SLP(gpa0-7, INPUT, UP); |
| |
| PIN_SLP(gpa1-0, INPUT, DOWN); |
| PIN_SLP(gpa1-1, INPUT, DOWN); |
| PIN_SLP(gpa1-2, INPUT, DOWN); |
| PIN_SLP(gpa1-3, INPUT, DOWN); |
| PIN_SLP(gpa1-4, INPUT, DOWN); |
| PIN_SLP(gpa1-5, INPUT, DOWN); |
| |
| PIN_SLP(gpb-0, INPUT, NONE); |
| PIN_SLP(gpb-1, INPUT, NONE); |
| PIN_SLP(gpb-2, INPUT, NONE); |
| PIN_SLP(gpb-3, INPUT, NONE); |
| PIN_SLP(gpb-4, INPUT, DOWN); |
| PIN_SLP(gpb-5, INPUT, DOWN); |
| PIN_SLP(gpb-6, INPUT, DOWN); |
| PIN_SLP(gpb-7, INPUT, DOWN); |
| |
| PIN_SLP(gpc0-0, INPUT, DOWN); |
| PIN_SLP(gpc0-1, INPUT, DOWN); |
| PIN_SLP(gpc0-2, INPUT, DOWN); |
| PIN_SLP(gpc0-3, INPUT, DOWN); |
| PIN_SLP(gpc0-4, INPUT, DOWN); |
| |
| PIN_SLP(gpc1-0, INPUT, UP); |
| PIN_SLP(gpc1-1, PREV, NONE); |
| PIN_SLP(gpc1-2, INPUT, UP); |
| PIN_SLP(gpc1-3, INPUT, UP); |
| PIN_SLP(gpc1-4, INPUT, UP); |
| |
| PIN_SLP(gpd0-0, INPUT, DOWN); |
| PIN_SLP(gpd0-1, OUT0, NONE); |
| PIN_SLP(gpd0-2, INPUT, NONE); |
| PIN_SLP(gpd0-3, INPUT, NONE); |
| |
| PIN_SLP(gpd1-0, INPUT, DOWN); |
| PIN_SLP(gpd1-1, INPUT, DOWN); |
| PIN_SLP(gpd1-2, INPUT, NONE); |
| PIN_SLP(gpd1-3, INPUT, NONE); |
| |
| PIN_SLP(gpf0-0, OUT0, NONE); |
| PIN_SLP(gpf0-1, OUT0, NONE); |
| PIN_SLP(gpf0-2, OUT0, NONE); |
| PIN_SLP(gpf0-3, OUT0, NONE); |
| PIN_SLP(gpf0-4, OUT0, NONE); |
| PIN_SLP(gpf0-5, OUT0, NONE); |
| PIN_SLP(gpf0-6, OUT0, NONE); |
| PIN_SLP(gpf0-7, OUT0, NONE); |
| |
| PIN_SLP(gpf1-0, OUT0, NONE); |
| PIN_SLP(gpf1-1, OUT0, NONE); |
| PIN_SLP(gpf1-2, OUT0, NONE); |
| PIN_SLP(gpf1-3, OUT0, NONE); |
| PIN_SLP(gpf1-4, OUT0, NONE); |
| PIN_SLP(gpf1-5, OUT0, NONE); |
| PIN_SLP(gpf1-6, OUT0, NONE); |
| PIN_SLP(gpf1-7, OUT0, NONE); |
| |
| PIN_SLP(gpf2-0, OUT0, NONE); |
| PIN_SLP(gpf2-1, OUT0, NONE); |
| PIN_SLP(gpf2-2, OUT0, NONE); |
| PIN_SLP(gpf2-3, OUT0, NONE); |
| PIN_SLP(gpf2-4, OUT0, NONE); |
| PIN_SLP(gpf2-5, OUT0, NONE); |
| PIN_SLP(gpf2-6, OUT0, NONE); |
| PIN_SLP(gpf2-7, OUT0, NONE); |
| |
| PIN_SLP(gpf3-0, OUT0, NONE); |
| PIN_SLP(gpf3-1, OUT0, NONE); |
| PIN_SLP(gpf3-2, OUT0, NONE); |
| PIN_SLP(gpf3-3, OUT0, NONE); |
| PIN_SLP(gpf3-4, OUT0, NONE); |
| PIN_SLP(gpf3-5, OUT0, NONE); |
| |
| PIN_SLP(gpj0-0, INPUT, DOWN); |
| PIN_SLP(gpj0-1, INPUT, DOWN); |
| PIN_SLP(gpj0-2, INPUT, DOWN); |
| PIN_SLP(gpj0-3, PREV, NONE); |
| PIN_SLP(gpj0-4, PREV, NONE); |
| PIN_SLP(gpj0-5, OUT0, NONE); |
| PIN_SLP(gpj0-6, OUT0, NONE); |
| PIN_SLP(gpj0-7, OUT0, NONE); |
| |
| PIN_SLP(gpj1-0, OUT0, NONE); |
| PIN_SLP(gpj1-1, INPUT, DOWN); |
| PIN_SLP(gpj1-2, PREV, NONE); |
| PIN_SLP(gpj1-3, OUT0, NONE); |
| }; |
| }; |
| |
| &pinctrl_1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&sleep1>; |
| |
| sd3_wifi: sd3-wifi-pins { |
| samsung,pins = "gpk3-3", "gpk3-4", "gpk3-5", "gpk3-6"; |
| samsung,pin-function = <EXYNOS_PIN_FUNC_2>; |
| samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; |
| }; |
| |
| bt_shutdown: bt-shutdown-pins { |
| samsung,pins = "gpl0-6"; |
| samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>; |
| samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; |
| }; |
| |
| gyro_data_enable: gyro-data-enable-pins { |
| samsung,pins = "gpl2-0"; |
| samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>; |
| samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>; |
| }; |
| |
| uart_sel: uart-sel-pins { |
| samsung,pins = "gpl2-7"; |
| samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>; |
| samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; |
| samsung,pin-val = <1>; |
| /* 0 = CP, 1 = AP (serial output) */ |
| }; |
| |
| led_bl_reset: led-bl-reset-pins { |
| samsung,pins = "gpm0-1"; |
| samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>; |
| samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; |
| }; |
| |
| tsp_rst: tsp-rst-pins { |
| samsung,pins = "gpm0-4"; |
| samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>; |
| samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; |
| }; |
| |
| lvds_nshdn: lvds-nshdn-pins { |
| samsung,pins = "gpm0-5"; |
| samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>; |
| samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; |
| }; |
| |
| tsp_irq: tsp-irq-pins { |
| samsung,pins = "gpm2-3"; |
| samsung,pin-function = <EXYNOS_PIN_FUNC_F>; |
| samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; |
| }; |
| |
| wifi_reset: wifi-reset-pins { |
| samsung,pins = "gpm3-5"; |
| samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>; |
| samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; |
| }; |
| |
| tsp_reg_gpio_1: tsp-reg-gpio-1-pins { |
| samsung,pins = "gpm4-5"; |
| samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>; |
| samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; |
| }; |
| |
| ak8975_irq: ak8975-irq-pins { |
| samsung,pins = "gpm4-7"; |
| samsung,pin-function = <EXYNOS_PIN_FUNC_F>; |
| samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>; |
| }; |
| |
| accelerometer_irq: accelerometer-irq-pins { |
| samsung,pins = "gpx0-0"; |
| samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>; |
| samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; |
| }; |
| |
| stmpe_adc_irq: stmpe-adc-irq-pins { |
| samsung,pins = "gpx0-1"; |
| samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>; |
| samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; |
| }; |
| |
| gyro_irq: gyro-irq-pins { |
| samsung,pins = "gpx0-6"; |
| samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>; |
| samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; |
| }; |
| |
| max77686_irq: max77686-irq-pins { |
| samsung,pins = "gpx0-7"; |
| samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; |
| }; |
| |
| gpio_keys: gpio-keys-pins { |
| samsung,pins = "gpx2-2", "gpx2-7", "gpx3-3"; |
| samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; |
| }; |
| |
| fuel_alert_irq: fuel-alert-irq-pins { |
| samsung,pins = "gpx2-3"; |
| samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>; |
| samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; |
| }; |
| |
| wifi_host_wake: wifi-host-wake-pins { |
| samsung,pins = "gpx2-5"; |
| samsung,pin-function = <EXYNOS_PIN_FUNC_F>; |
| samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>; |
| }; |
| |
| bt_host_wakeup: bt-host-wakeup-pins { |
| samsung,pins = "gpx2-6"; |
| samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>; |
| samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; |
| }; |
| |
| bt_device_wakeup: bt-device-wakeup-pins { |
| samsung,pins = "gpx3-1"; |
| samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>; |
| samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; |
| }; |
| |
| sdhci2_cd: sdhci2-cd-pins { |
| samsung,pins = "gpx3-4"; |
| samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; |
| }; |
| |
| sleep1: sleep-state { |
| PIN_SLP(gpk0-0, PREV, NONE); |
| PIN_SLP(gpk0-1, PREV, NONE); |
| PIN_SLP(gpk0-2, PREV, NONE); |
| PIN_SLP(gpk0-3, PREV, NONE); |
| PIN_SLP(gpk0-4, PREV, NONE); |
| PIN_SLP(gpk0-5, PREV, NONE); |
| PIN_SLP(gpk0-6, PREV, NONE); |
| |
| PIN_SLP(gpk1-0, INPUT, DOWN); |
| PIN_SLP(gpk1-1, INPUT, DOWN); |
| PIN_SLP(gpk1-2, INPUT, DOWN); |
| PIN_SLP(gpk1-3, PREV, NONE); |
| PIN_SLP(gpk1-4, PREV, NONE); |
| PIN_SLP(gpk1-5, PREV, NONE); |
| PIN_SLP(gpk1-6, PREV, NONE); |
| |
| PIN_SLP(gpk2-0, INPUT, DOWN); |
| PIN_SLP(gpk2-1, INPUT, DOWN); |
| PIN_SLP(gpk2-2, INPUT, DOWN); |
| PIN_SLP(gpk2-3, INPUT, DOWN); |
| PIN_SLP(gpk2-4, INPUT, DOWN); |
| PIN_SLP(gpk2-5, INPUT, DOWN); |
| PIN_SLP(gpk2-6, INPUT, DOWN); |
| |
| PIN_SLP(gpk3-0, OUT0, NONE); |
| PIN_SLP(gpk3-1, INPUT, NONE); |
| PIN_SLP(gpk3-2, INPUT, DOWN); |
| PIN_SLP(gpk3-3, INPUT, NONE); |
| PIN_SLP(gpk3-4, INPUT, NONE); |
| PIN_SLP(gpk3-5, INPUT, NONE); |
| PIN_SLP(gpk3-6, INPUT, NONE); |
| |
| PIN_SLP(gpl0-0, OUT0, NONE); |
| PIN_SLP(gpl0-1, INPUT, NONE); |
| PIN_SLP(gpl0-2, INPUT, NONE); |
| PIN_SLP(gpl0-3, INPUT, DOWN); |
| PIN_SLP(gpl0-4, PREV, NONE); |
| PIN_SLP(gpl0-6, PREV, NONE); |
| |
| PIN_SLP(gpl1-0, OUT0, NONE); |
| PIN_SLP(gpl1-1, OUT0, NONE); |
| |
| PIN_SLP(gpl2-0, INPUT, DOWN); |
| PIN_SLP(gpl2-1, INPUT, DOWN); |
| PIN_SLP(gpl2-2, INPUT, DOWN); |
| PIN_SLP(gpl2-3, INPUT, DOWN); |
| PIN_SLP(gpl2-4, OUT0, NONE); |
| PIN_SLP(gpl2-5, INPUT, DOWN); |
| PIN_SLP(gpl2-6, PREV, NONE); |
| PIN_SLP(gpl2-7, PREV, NONE); |
| |
| PIN_SLP(gpm0-0, PREV, NONE); |
| PIN_SLP(gpm0-1, OUT0, NONE); |
| PIN_SLP(gpm0-2, INPUT, DOWN); |
| PIN_SLP(gpm0-3, INPUT, NONE); |
| PIN_SLP(gpm0-4, OUT0, NONE); |
| PIN_SLP(gpm0-5, OUT0, NONE); |
| PIN_SLP(gpm0-6, INPUT, DOWN); |
| PIN_SLP(gpm0-7, OUT0, NONE); |
| |
| PIN_SLP(gpm1-0, INPUT, NONE); |
| PIN_SLP(gpm1-1, INPUT, NONE); |
| PIN_SLP(gpm1-2, INPUT, NONE); |
| PIN_SLP(gpm1-3, INPUT, NONE); |
| PIN_SLP(gpm1-4, INPUT, NONE); |
| PIN_SLP(gpm1-5, INPUT, NONE); |
| PIN_SLP(gpm1-6, INPUT, DOWN); |
| |
| PIN_SLP(gpm2-0, INPUT, NONE); |
| PIN_SLP(gpm2-1, INPUT, NONE); |
| PIN_SLP(gpm2-2, OUT0, NONE); |
| PIN_SLP(gpm2-3, OUT0, DOWN); |
| PIN_SLP(gpm2-4, INPUT, DOWN); |
| |
| PIN_SLP(gpm3-0, PREV, NONE); |
| PIN_SLP(gpm3-1, PREV, NONE); |
| PIN_SLP(gpm3-2, PREV, NONE); |
| PIN_SLP(gpm3-3, OUT1, NONE); |
| PIN_SLP(gpm3-4, OUT0, DOWN); |
| PIN_SLP(gpm3-5, PREV, NONE); |
| PIN_SLP(gpm3-6, PREV, NONE); |
| PIN_SLP(gpm3-7, OUT0, NONE); |
| |
| PIN_SLP(gpm4-0, INPUT, NONE); |
| PIN_SLP(gpm4-1, INPUT, NONE); |
| PIN_SLP(gpm4-2, INPUT, DOWN); |
| PIN_SLP(gpm4-3, INPUT, DOWN); |
| PIN_SLP(gpm4-4, PREV, NONE); |
| PIN_SLP(gpm4-5, OUT0, NONE); |
| PIN_SLP(gpm4-6, OUT0, NONE); |
| PIN_SLP(gpm4-7, INPUT, DOWN); |
| |
| PIN_SLP(gpy0-0, INPUT, DOWN); |
| PIN_SLP(gpy0-1, INPUT, DOWN); |
| PIN_SLP(gpy0-2, INPUT, NONE); |
| PIN_SLP(gpy0-3, INPUT, NONE); |
| PIN_SLP(gpy0-4, INPUT, NONE); |
| PIN_SLP(gpy0-5, INPUT, NONE); |
| |
| PIN_SLP(gpy1-0, INPUT, DOWN); |
| PIN_SLP(gpy1-1, INPUT, DOWN); |
| PIN_SLP(gpy1-2, INPUT, DOWN); |
| PIN_SLP(gpy1-3, INPUT, DOWN); |
| |
| PIN_SLP(gpy2-0, PREV, NONE); |
| PIN_SLP(gpy2-1, INPUT, DOWN); |
| PIN_SLP(gpy2-2, INPUT, NONE); |
| PIN_SLP(gpy2-3, INPUT, NONE); |
| PIN_SLP(gpy2-4, INPUT, NONE); |
| PIN_SLP(gpy2-5, INPUT, NONE); |
| |
| PIN_SLP(gpy3-0, INPUT, DOWN); |
| PIN_SLP(gpy3-1, INPUT, DOWN); |
| PIN_SLP(gpy3-2, INPUT, DOWN); |
| PIN_SLP(gpy3-3, INPUT, DOWN); |
| PIN_SLP(gpy3-4, INPUT, DOWN); |
| PIN_SLP(gpy3-5, INPUT, DOWN); |
| PIN_SLP(gpy3-6, INPUT, DOWN); |
| PIN_SLP(gpy3-7, INPUT, DOWN); |
| |
| PIN_SLP(gpy4-0, INPUT, DOWN); |
| PIN_SLP(gpy4-1, INPUT, DOWN); |
| PIN_SLP(gpy4-2, INPUT, DOWN); |
| PIN_SLP(gpy4-3, INPUT, DOWN); |
| PIN_SLP(gpy4-4, INPUT, DOWN); |
| PIN_SLP(gpy4-5, INPUT, DOWN); |
| PIN_SLP(gpy4-6, INPUT, DOWN); |
| PIN_SLP(gpy4-7, INPUT, DOWN); |
| |
| PIN_SLP(gpy5-0, INPUT, DOWN); |
| PIN_SLP(gpy5-1, INPUT, DOWN); |
| PIN_SLP(gpy5-2, INPUT, DOWN); |
| PIN_SLP(gpy5-3, INPUT, DOWN); |
| PIN_SLP(gpy5-4, INPUT, DOWN); |
| PIN_SLP(gpy5-5, INPUT, DOWN); |
| PIN_SLP(gpy5-6, INPUT, DOWN); |
| PIN_SLP(gpy5-7, INPUT, DOWN); |
| |
| PIN_SLP(gpy6-0, INPUT, DOWN); |
| PIN_SLP(gpy6-1, INPUT, DOWN); |
| PIN_SLP(gpy6-2, INPUT, DOWN); |
| PIN_SLP(gpy6-3, INPUT, DOWN); |
| PIN_SLP(gpy6-4, INPUT, DOWN); |
| PIN_SLP(gpy6-5, INPUT, DOWN); |
| PIN_SLP(gpy6-6, INPUT, DOWN); |
| PIN_SLP(gpy6-7, INPUT, DOWN); |
| }; |
| }; |
| |
| &pinctrl_2 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&sleep2>; |
| |
| sleep2: sleep-state { |
| PIN_SLP(gpz-0, INPUT, DOWN); |
| PIN_SLP(gpz-1, INPUT, DOWN); |
| PIN_SLP(gpz-2, INPUT, DOWN); |
| PIN_SLP(gpz-3, INPUT, DOWN); |
| PIN_SLP(gpz-4, INPUT, DOWN); |
| PIN_SLP(gpz-5, INPUT, DOWN); |
| PIN_SLP(gpz-6, INPUT, DOWN); |
| }; |
| }; |
| |
| &pinctrl_3 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&sleep3>; |
| |
| sleep3: sleep-state { |
| PIN_SLP(gpv0-0, INPUT, DOWN); |
| PIN_SLP(gpv0-1, INPUT, DOWN); |
| PIN_SLP(gpv0-2, INPUT, DOWN); |
| PIN_SLP(gpv0-3, INPUT, DOWN); |
| PIN_SLP(gpv0-4, INPUT, DOWN); |
| PIN_SLP(gpv0-5, INPUT, DOWN); |
| PIN_SLP(gpv0-6, INPUT, DOWN); |
| PIN_SLP(gpv0-7, INPUT, DOWN); |
| |
| PIN_SLP(gpv1-0, INPUT, DOWN); |
| PIN_SLP(gpv1-1, INPUT, DOWN); |
| PIN_SLP(gpv1-2, INPUT, DOWN); |
| PIN_SLP(gpv1-3, INPUT, DOWN); |
| PIN_SLP(gpv1-4, INPUT, DOWN); |
| PIN_SLP(gpv1-5, INPUT, DOWN); |
| PIN_SLP(gpv1-6, INPUT, DOWN); |
| PIN_SLP(gpv1-7, INPUT, DOWN); |
| |
| PIN_SLP(gpv2-0, INPUT, DOWN); |
| PIN_SLP(gpv2-1, INPUT, DOWN); |
| PIN_SLP(gpv2-2, INPUT, DOWN); |
| PIN_SLP(gpv2-3, INPUT, DOWN); |
| PIN_SLP(gpv2-4, INPUT, DOWN); |
| PIN_SLP(gpv2-5, INPUT, DOWN); |
| PIN_SLP(gpv2-6, INPUT, DOWN); |
| PIN_SLP(gpv2-7, INPUT, DOWN); |
| |
| PIN_SLP(gpv3-0, INPUT, DOWN); |
| PIN_SLP(gpv3-1, INPUT, DOWN); |
| PIN_SLP(gpv3-2, INPUT, DOWN); |
| PIN_SLP(gpv3-3, INPUT, DOWN); |
| PIN_SLP(gpv3-4, INPUT, DOWN); |
| PIN_SLP(gpv3-5, INPUT, DOWN); |
| PIN_SLP(gpv3-6, INPUT, DOWN); |
| PIN_SLP(gpv3-7, INPUT, DOWN); |
| |
| PIN_SLP(gpv4-0, INPUT, DOWN); |
| PIN_SLP(gpv4-1, INPUT, DOWN); |
| }; |
| }; |
| |
| &pmu_system_controller { |
| assigned-clocks = <&pmu_system_controller 0>; |
| assigned-clock-parents = <&clock CLK_XUSBXTI>; |
| }; |
| |
| &pwm { |
| pinctrl-0 = <&pwm1_out>; |
| pinctrl-names = "default"; |
| samsung,pwm-outputs = <1>; |
| status = "okay"; |
| }; |
| |
| &rtc { |
| clocks = <&clock CLK_RTC>, <&max77686 MAX77686_CLK_AP>; |
| clock-names = "rtc", "rtc_src"; |
| status = "okay"; |
| }; |
| |
| &sdhci_2 { |
| bus-width = <4>; |
| cd-gpios = <&gpx3 4 GPIO_ACTIVE_LOW>; |
| pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus4 &sdhci2_cd>; |
| pinctrl-names = "default"; |
| vmmc-supply = <&ldo21_reg>; |
| status = "okay"; |
| }; |
| |
| &sdhci_3 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| non-removable; |
| bus-width = <4>; |
| mmc-pwrseq = <&wlan_pwrseq>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&sd3_clk &sd3_cmd &sd3_wifi>; |
| status = "okay"; |
| |
| wifi@1 { |
| compatible = "brcm,bcm4329-fmac"; |
| reg = <0x1>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&wifi_host_wake>; |
| interrupt-parent = <&gpx2>; |
| interrupts = <5 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "host-wake"; |
| }; |
| }; |
| |
| &serial_0 { |
| pinctrl-0 = <&uart0_data &uart0_fctl>; |
| pinctrl-names = "default"; |
| status = "okay"; |
| |
| bluetooth { |
| compatible = "brcm,bcm4330-bt"; |
| pinctrl-0 = <&bt_shutdown &bt_device_wakeup &bt_host_wakeup>; |
| pinctrl-names = "default"; |
| |
| max-speed = <2000000>; |
| shutdown-gpios = <&gpl0 6 GPIO_ACTIVE_HIGH>; |
| device-wakeup-gpios = <&gpx3 1 GPIO_ACTIVE_HIGH>; |
| host-wakeup-gpios = <&gpx2 6 GPIO_ACTIVE_HIGH>; |
| clocks = <&max77686 MAX77686_CLK_PMIC>; |
| clock-names = "lpo"; |
| }; |
| }; |
| |
| &serial_2 { |
| pinctrl-0 = <&uart_sel>; |
| pinctrl-names = "default"; |
| status = "okay"; |
| }; |
| |
| &tmu { |
| status = "okay"; |
| }; |