include/configs/gw_ventana.h - filogic/uboot - Gitiles

 /*
  * Copyright (C) 2013 Gateworks Corporation
  *
  * SPDX-License-Identifier: GPL-2.0+
  */

 #ifndef __CONFIG_H
 #define __CONFIG_H

 /* SPL */
 #define CONFIG_SPL_NAND_SUPPORT
 #define CONFIG_SPL_MMC_SUPPORT
 #define CONFIG_SPL_FAT_SUPPORT
 /*
 #define CONFIG_SPL_SATA_SUPPORT
 */
 /* Location in NAND to read U-Boot from */
 #define CONFIG_SYS_NAND_U_BOOT_OFFS     (14 * 1024 * 1024)

 #include "imx6_spl.h"                  /* common IMX6 SPL configuration */
 #include "mx6_common.h"
 #define CONFIG_MX6
 #define CONFIG_DISPLAY_CPUINFO         /* display cpu info */
 #define CONFIG_DISPLAY_BOARDINFO_LATE  /* display board info (after reloc) */

 #define CONFIG_MACH_TYPE	4520   /* Gateworks Ventana Platform */

 #include <asm/arch/imx-regs.h>
 #include <asm/imx-common/gpio.h>

 /* ATAGs */
 #define CONFIG_CMDLINE_TAG
 #define CONFIG_SETUP_MEMORY_TAGS
 #define CONFIG_INITRD_TAG
 #define CONFIG_SERIAL_TAG
 #define CONFIG_REVISION_TAG

 #define CONFIG_SYS_GENERIC_BOARD

 /* Size of malloc() pool */
 #define CONFIG_SYS_MALLOC_LEN		(10 * 1024 * 1024)

 /* Init Functions */
 #define CONFIG_BOARD_EARLY_INIT_F
 #define CONFIG_MISC_INIT_R

 /* GPIO */
 #define CONFIG_MXC_GPIO

 /* Serial */
 #define CONFIG_MXC_UART
 #define CONFIG_MXC_UART_BASE	       UART2_BASE

 #ifdef CONFIG_SPI_FLASH

 /* SPI */
 #define CONFIG_CMD_SF
 #ifdef CONFIG_CMD_SF
   #define CONFIG_MXC_SPI
   #define CONFIG_SPI_FLASH_MTD
   #define CONFIG_SPI_FLASH_BAR
   #define CONFIG_SPI_FLASH_WINBOND
   #define CONFIG_SF_DEFAULT_BUS              0
   #define CONFIG_SF_DEFAULT_CS               0
 					     /* GPIO 3-19 (21248) */
   #define CONFIG_SF_DEFAULT_SPEED            30000000
   #define CONFIG_SF_DEFAULT_MODE             (SPI_MODE_0)
 #endif

 #else
 /* Enable NAND support */
 #define CONFIG_CMD_TIME
 #define CONFIG_CMD_NAND
 #define CONFIG_CMD_NAND_TRIMFFS
 #ifdef CONFIG_CMD_NAND
   #define CONFIG_NAND_MXS
   #define CONFIG_SYS_MAX_NAND_DEVICE	1
   #define CONFIG_SYS_NAND_BASE		0x40000000
   #define CONFIG_SYS_NAND_5_ADDR_CYCLE
   #define CONFIG_SYS_NAND_ONFI_DETECTION

   /* DMA stuff, needed for GPMI/MXS NAND support */
   #define CONFIG_APBH_DMA
   #define CONFIG_APBH_DMA_BURST
   #define CONFIG_APBH_DMA_BURST8
 #endif

 #endif /* CONFIG_SPI_FLASH */

 /* Flattened Image Tree Suport */
 #define CONFIG_FIT
 #define CONFIG_FIT_VERBOSE

 /* I2C Configs */
 #define CONFIG_CMD_I2C
 #define CONFIG_SYS_I2C
 #define CONFIG_SYS_I2C_MXC
 #define CONFIG_SYS_I2C_SPEED		100000
 #define CONFIG_I2C_GSC			0
 #define CONFIG_I2C_PMIC			1

 /* MMC Configs */
 #define CONFIG_FSL_ESDHC
 #define CONFIG_FSL_USDHC
 #define CONFIG_SYS_FSL_ESDHC_ADDR      0
 #define CONFIG_SYS_FSL_USDHC_NUM       1
 #define CONFIG_MMC
 #define CONFIG_CMD_MMC
 #define CONFIG_GENERIC_MMC
 #define CONFIG_BOUNCE_BUFFER

 /* Filesystem support */
 #define CONFIG_CMD_EXT2
 #define CONFIG_CMD_FAT
 #define CONFIG_CMD_UBIFS
 #define CONFIG_DOS_PARTITION

 /*
  * SATA Configs
  */
 #define CONFIG_CMD_SATA
 #ifdef CONFIG_CMD_SATA
   #define CONFIG_DWC_AHSATA
   #define CONFIG_SYS_SATA_MAX_DEVICE	1
   #define CONFIG_DWC_AHSATA_PORT_ID	0
   #define CONFIG_DWC_AHSATA_BASE_ADDR	SATA_ARB_BASE_ADDR
   #define CONFIG_LBA48
   #define CONFIG_LIBATA
 #endif

 /*
  * PCI express
  */
 #define CONFIG_CMD_PCI
 #ifdef CONFIG_CMD_PCI
 #define CONFIG_PCI
 #define CONFIG_PCI_PNP
 #define CONFIG_PCI_SCAN_SHOW
 #define CONFIG_PCI_FIXUP_DEV
 #define CONFIG_PCIE_IMX
 #endif

 /*
  * PMIC
  */
 #define CONFIG_POWER
 #define CONFIG_POWER_I2C
 #define CONFIG_POWER_PFUZE100
 #define CONFIG_POWER_PFUZE100_I2C_ADDR	0x08
 #define CONFIG_POWER_LTC3676
 #define CONFIG_POWER_LTC3676_I2C_ADDR  0x3c

 /* Various command support */
 #include <config_cmd_default.h>
 #undef CONFIG_CMD_IMLS
 #define CONFIG_CMD_PING
 #define CONFIG_CMD_DHCP
 #define CONFIG_CMD_MII
 #define CONFIG_CMD_NET
 #define CONFIG_CMD_BMODE         /* set eFUSE shadow for a boot dev and reset */
 #define CONFIG_CMD_HDMIDETECT    /* detect HDMI output device */
 #define CONFIG_CMD_SETEXPR
 #define CONFIG_CMD_BOOTZ
 #define CONFIG_CMD_GSC
 #define CONFIG_CMD_EECONFIG      /* Gateworks EEPROM config cmd */
 #define CONFIG_CMD_UBI
 #define CONFIG_RBTREE
 #define CONFIG_LZO
 #define CONFIG_CMD_FUSE          /* eFUSE read/write support */
 #ifdef CONFIG_CMD_FUSE
 #define CONFIG_MXC_OCOTP
 #endif


 /* Ethernet support */
 #define CONFIG_FEC_MXC
 #define CONFIG_E1000
 #define CONFIG_MII
 #define IMX_FEC_BASE             ENET_BASE_ADDR
 #define CONFIG_FEC_XCV_TYPE      RGMII
 #define CONFIG_FEC_MXC_PHYADDR   0
 #define CONFIG_PHYLIB
 #define CONFIG_ARP_TIMEOUT       200UL

 /* USB Configs */
 #define CONFIG_CMD_USB
 #define CONFIG_USB_EHCI
 #define CONFIG_USB_EHCI_MX6
 #define CONFIG_USB_STORAGE
 #define CONFIG_USB_HOST_ETHER
 #define CONFIG_USB_ETHER_ASIX
 #define CONFIG_USB_ETHER_SMSC95XX
 #define CONFIG_USB_MAX_CONTROLLER_COUNT 2
 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET  /* For OTG port */
 #define CONFIG_MXC_USB_PORTSC     (PORT_PTS_UTMI | PORT_PTS_PTW)
 #define CONFIG_MXC_USB_FLAGS      0
 #define CONFIG_USB_KEYBOARD
 #define CONFIG_CI_UDC
 #define CONFIG_USBD_HS
 #define CONFIG_USB_GADGET_DUALSPEED
 #define CONFIG_USB_ETHER
 #define CONFIG_USB_ETH_CDC
 #define CONFIG_NETCONSOLE
 #define CONFIG_SYS_USB_EVENT_POLL_VIA_CONTROL_EP

 /* USB Mass Storage Gadget */
 #define CONFIG_USB_GADGET
 #define CONFIG_CMD_USB_MASS_STORAGE
 #define CONFIG_USB_GADGET_MASS_STORAGE
 #define CONFIG_USBDOWNLOAD_GADGET
 #define CONFIG_USB_GADGET_VBUS_DRAW    2

 /* Netchip IDs */
 #define CONFIG_G_DNL_VENDOR_NUM 0x0525
 #define CONFIG_G_DNL_PRODUCT_NUM 0xa4a5
 #define CONFIG_G_DNL_MANUFACTURER "Gateworks"

 /* Framebuffer and LCD */
 #define CONFIG_VIDEO
 #define CONFIG_VIDEO_IPUV3
 #define CONFIG_CFB_CONSOLE
 #define CONFIG_VGA_AS_SINGLE_DEVICE
 #define CONFIG_SYS_CONSOLE_IS_IN_ENV
 #define CONFIG_VIDEO_BMP_RLE8
 #define CONFIG_SPLASH_SCREEN
 #define CONFIG_BMP_16BPP
 #define CONFIG_VIDEO_LOGO
 #define CONFIG_IPUV3_CLK          260000000
 #define CONFIG_CMD_HDMIDETECT
 #define CONFIG_CONSOLE_MUX
 #define CONFIG_IMX_HDMI
 #define CONFIG_IMX_VIDEO_SKIP

 /* serial console (ttymxc1,115200) */
 #define CONFIG_CONS_INDEX              1
 #define CONFIG_BAUDRATE                115200

 /* Miscellaneous configurable options */
 #define CONFIG_SYS_LONGHELP
 #define CONFIG_SYS_HUSH_PARSER
 #define CONFIG_SYS_PROMPT	             "Ventana > "
 #define CONFIG_SYS_CBSIZE	             1024
 #define CONFIG_AUTO_COMPLETE
 #define CONFIG_CMDLINE_EDITING
 #define CONFIG_HWCONFIG

 /* Print Buffer Size */
 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
 #define CONFIG_SYS_MAXARGS	           16
 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE

 /* Memory configuration */
 #define CONFIG_SYS_MEMTEST_START       0x10000000
 #define CONFIG_SYS_MEMTEST_END	       0x10010000
 #define CONFIG_SYS_MEMTEST_SCRATCH     0x10800000
 #define CONFIG_SYS_TEXT_BASE	         0x17800000
 #define CONFIG_SYS_LOAD_ADDR           0x12000000

 /* Physical Memory Map */
 #define CONFIG_NR_DRAM_BANKS           1
 #define PHYS_SDRAM                     MMDC0_ARB_BASE_ADDR
 #define CONFIG_SYS_SDRAM_BASE          PHYS_SDRAM
 #define CONFIG_SYS_INIT_RAM_ADDR       IRAM_BASE_ADDR
 #define CONFIG_SYS_INIT_RAM_SIZE       IRAM_SIZE

 #define CONFIG_SYS_INIT_SP_OFFSET \
 	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_ADDR \
 	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)

 /* FLASH and environment organization */
 #define CONFIG_SYS_NO_FLASH  /* no NOR flash */

 /*
  * MTD Command for mtdparts
  */
 #define CONFIG_CMD_MTDPARTS
 #define CONFIG_MTD_DEVICE
 #define CONFIG_MTD_PARTITIONS
 #ifdef CONFIG_SPI_FLASH
 #define MTDIDS_DEFAULT    "nor0=nor"
 #define MTDPARTS_DEFAULT  \
 	"mtdparts=nor:512k(uboot),64k(env),2m(kernel),-(rootfs)"
 #else
 #define MTDIDS_DEFAULT    "nand0=nand"
 #define MTDPARTS_DEFAULT  "mtdparts=nand:16m(uboot),1m(env),-(rootfs)"
 #endif

 /* Persistent Environment Config */
 #define CONFIG_ENV_OVERWRITE    /* allow to overwrite serial and ethaddr */
 #ifdef CONFIG_SPI_FLASH
 #define CONFIG_ENV_IS_IN_SPI_FLASH
 #else
 #define CONFIG_ENV_IS_IN_NAND
 #endif
 #if defined(CONFIG_ENV_IS_IN_MMC)
   #define CONFIG_ENV_OFFSET              (6 * 64 * 1024)
   #define CONFIG_ENV_SIZE                (8 * 1024)
   #define CONFIG_SYS_MMC_ENV_DEV         0
 #elif defined(CONFIG_ENV_IS_IN_NAND)
   #define CONFIG_ENV_OFFSET              (16 << 20)
   #define CONFIG_ENV_SECT_SIZE           (128 << 10)
   #define CONFIG_ENV_SIZE                CONFIG_ENV_SECT_SIZE
   #define CONFIG_ENV_OFFSET_REDUND       (CONFIG_ENV_OFFSET + (512 << 10))
   #define CONFIG_ENV_SIZE_REDUND         CONFIG_ENV_SIZE
 #elif defined(CONFIG_ENV_IS_IN_SPI_FLASH)
   #define CONFIG_ENV_OFFSET              (512 * 1024)
   #define CONFIG_ENV_SECT_SIZE           (64 * 1024)
   #define CONFIG_ENV_SIZE                (8 * 1024)
   #define CONFIG_ENV_SPI_BUS             CONFIG_SF_DEFAULT_BUS
   #define CONFIG_ENV_SPI_CS              CONFIG_SF_DEFAULT_CS
   #define CONFIG_ENV_SPI_MODE            CONFIG_SF_DEFAULT_MODE
   #define CONFIG_ENV_SPI_MAX_HZ          CONFIG_SF_DEFAULT_SPEED
 #endif

 /* Environment */
 #define CONFIG_BOOTDELAY          3
 #define CONFIG_LOADADDR           CONFIG_SYS_LOAD_ADDR
 #define CONFIG_IPADDR             192.168.1.1
 #define CONFIG_SERVERIP           192.168.1.146
 #define HWCONFIG_DEFAULT \
 	"hwconfig=rs232;" \
 	"dio0:mode=gpio;dio1:mode=gpio;dio2:mode=gpio;dio3:mode=gpio\0" \

 #define CONFIG_EXTRA_ENV_SETTINGS_COMMON \
 	"console=ttymxc1\0" \
 	"bootdevs=usb mmc sata flash\0" \
 	HWCONFIG_DEFAULT \
 	"video=\0" \
 	\
 	"mtdparts=" MTDPARTS_DEFAULT "\0" \
 	"mtdids=" MTDIDS_DEFAULT "\0" \
 	\
 	"fdt_high=0xffffffff\0" \
 	"fdt_addr=0x18000000\0" \
 	"initrd_high=0xffffffff\0" \
 	"loadfdt=" \
 		"if ${fsload} ${fdt_addr} boot/${fdt_file}; then " \
 			"echo Loaded DTB from boot/${fdt_file}; " \
 		"elif ${fsload} ${fdt_addr} boot/${fdt_file1}; then " \
 			"echo Loaded DTB from boot/${fdt_file1}; " \
 		"elif ${fsload} ${fdt_addr} boot/${fdt_file2}; then " \
 				"echo Loaded DTB from boot/${fdt_file2}; " \
 		"fi\0" \
 	\
 	"script=boot/6x_bootscript-ventana\0" \
 	"loadscript=" \
 		"if ${fsload} ${loadaddr} ${script}; then " \
 			"source; " \
 		"fi\0" \
 	\
 	"uimage=boot/uImage\0" \
 	"mmc_root=/dev/mmcblk0p1 rootfstype=ext4 rootwait rw\0" \
 	"mmc_boot=" \
 		"setenv fsload 'ext2load mmc 0:1'; " \
 		"mmc dev 0 && mmc rescan && " \
 		"run loadscript; " \
 		"if ${fsload} ${loadaddr} ${uimage}; then " \
 			"setenv bootargs console=${console},${baudrate} " \
 				"root=/dev/mmcblk0p1 rootfstype=ext4 " \
 				"rootwait rw ${video} ${extra}; " \
 			"if run loadfdt && fdt addr ${fdt_addr}; then " \
 				"bootm ${loadaddr} - ${fdt_addr}; " \
 			"else " \
 				"bootm; " \
 			"fi; " \
 		"fi\0" \
 	\
 	"sata_boot=" \
 		"setenv fsload 'ext2load sata 0:1'; sata init && " \
 		"run loadscript; " \
 		"if ${fsload} ${loadaddr} ${uimage}; then " \
 			"setenv bootargs console=${console},${baudrate} " \
 				"root=/dev/sda1 rootfstype=ext4 " \
 				"rootwait rw ${video} ${extra}; " \
 			"if run loadfdt && fdt addr ${fdt_addr}; then " \
 				"bootm ${loadaddr} - ${fdt_addr}; " \
 			"else " \
 				"bootm; " \
 			"fi; " \
 		"fi\0" \
 	"usb_boot=" \
 		"setenv fsload 'ext2load usb 0:1'; usb start && usb dev 0 && " \
 		"run loadscript; " \
 		"if ${fsload} ${loadaddr} ${uimage}; then " \
 			"setenv bootargs console=${console},${baudrate} " \
 				"root=/dev/sda1 rootfstype=ext4 " \
 				"rootwait rw ${video} ${extra}; " \
 			"if run loadfdt && fdt addr ${fdt_addr}; then " \
 				"bootm ${loadaddr} - ${fdt_addr}; " \
 			"else " \
 				"bootm; " \
 			"fi; " \
 		"fi\0"

 #ifdef CONFIG_SPI_FLASH
 	#define CONFIG_EXTRA_ENV_SETTINGS \
 	CONFIG_EXTRA_ENV_SETTINGS_COMMON \
 	"image_os=ventana/openwrt-imx6-imx6q-gw5400-a-squashfs.bin\0" \
 	"image_uboot=ventana/u-boot_spi.imx\0" \
 	\
 	"spi_koffset=0x90000\0" \
 	"spi_klen=0x200000\0" \
 	\
 	"spi_updateuboot=echo Updating uboot from " \
 		"${serverip}:${image_uboot}...; " \
 		"tftpboot ${loadaddr} ${image_uboot} && " \
 		"sf probe && sf erase 0 80000 && " \
 			"sf write ${loadaddr} 400 ${filesize}\0" \
 	"spi_update=echo Updating OS from ${serverip}:${image_os} " \
 		"to ${spi_koffset} ...; " \
 		"tftp ${loadaddr} ${image_os} && " \
 		"sf probe && " \
 		"sf update ${loadaddr} ${spi_koffset} ${filesize}\0" \
 	\
 	"flash_boot=" \
 		"if sf probe && " \
 		"sf read ${loadaddr} ${spi_koffset} ${spi_klen}; then " \
 			"setenv bootargs console=${console},${baudrate} " \
 				"root=/dev/mtdblock3 " \
 				"rootfstype=squashfs,jffs2 " \
 				"${video} ${extra}; " \
 			"bootm; " \
 		"fi\0"
 #else
 	#define CONFIG_EXTRA_ENV_SETTINGS \
 	CONFIG_EXTRA_ENV_SETTINGS_COMMON \
 	"image_rootfs=openwrt-imx6-ventana-rootfs.ubi\0" \
 	\
 	"nand_update=echo Updating NAND from ${serverip}:${image_rootfs}...; " \
 		"tftp ${loadaddr} ${image_rootfs} && " \
 		"nand erase.part rootfs && " \
 		"nand write ${loadaddr} rootfs ${filesize}\0" \
 	\
 	"flash_boot=" \
 		"setenv fsload 'ubifsload'; " \
 		"ubi part rootfs && ubifsmount ubi0:rootfs; " \
 		"run loadscript; " \
 		"if ${fsload} ${loadaddr} ${uimage}; then " \
 			"setenv bootargs console=${console},${baudrate} " \
 				"root=ubi0:rootfs ubi.mtd=2 " \
 				"rootfstype=ubifs ${video} ${extra}; " \
 			"if run loadfdt && fdt addr ${fdt_addr}; then " \
 				"ubifsumount; " \
 				"bootm ${loadaddr} - ${fdt_addr}; " \
 			"else " \
 				"ubifsumount; bootm; " \
 			"fi; " \
 		"fi\0"
 #endif

 #define CONFIG_BOOTCOMMAND \
 	"for btype in ${bootdevs}; do " \
 		"echo; echo Attempting ${btype} boot...; " \
 		"if run ${btype}_boot; then; fi; " \
 	"done"

 /* Device Tree Support */
 #define CONFIG_OF_BOARD_SETUP
 #define CONFIG_OF_LIBFDT
 #define CONFIG_FDT_FIXUP_PARTITIONS

 #ifndef CONFIG_SYS_DCACHE_OFF
   #define CONFIG_CMD_CACHE
 #endif

 #endif			       /* __CONFIG_H */
	/*
	* Copyright (C) 2013 Gateworks Corporation
	*
	* SPDX-License-Identifier: GPL-2.0+
	*/

	#ifndef __CONFIG_H
	#define __CONFIG_H

	/* SPL */
	#define CONFIG_SPL_NAND_SUPPORT
	#define CONFIG_SPL_MMC_SUPPORT
	#define CONFIG_SPL_FAT_SUPPORT
	/*
	#define CONFIG_SPL_SATA_SUPPORT
	*/
	/* Location in NAND to read U-Boot from */
	#define CONFIG_SYS_NAND_U_BOOT_OFFS (14 * 1024 * 1024)

	#include "imx6_spl.h" /* common IMX6 SPL configuration */
	#include "mx6_common.h"
	#define CONFIG_MX6
	#define CONFIG_DISPLAY_CPUINFO /* display cpu info */
	#define CONFIG_DISPLAY_BOARDINFO_LATE /* display board info (after reloc) */

	#define CONFIG_MACH_TYPE 4520 /* Gateworks Ventana Platform */

	#include <asm/arch/imx-regs.h>
	#include <asm/imx-common/gpio.h>

	/* ATAGs */
	#define CONFIG_CMDLINE_TAG
	#define CONFIG_SETUP_MEMORY_TAGS
	#define CONFIG_INITRD_TAG
	#define CONFIG_SERIAL_TAG
	#define CONFIG_REVISION_TAG

	#define CONFIG_SYS_GENERIC_BOARD

	/* Size of malloc() pool */
	#define CONFIG_SYS_MALLOC_LEN (10 * 1024 * 1024)

	/* Init Functions */
	#define CONFIG_BOARD_EARLY_INIT_F
	#define CONFIG_MISC_INIT_R

	/* GPIO */
	#define CONFIG_MXC_GPIO

	/* Serial */
	#define CONFIG_MXC_UART
	#define CONFIG_MXC_UART_BASE UART2_BASE

	#ifdef CONFIG_SPI_FLASH

	/* SPI */
	#define CONFIG_CMD_SF
	#ifdef CONFIG_CMD_SF
	#define CONFIG_MXC_SPI
	#define CONFIG_SPI_FLASH_MTD
	#define CONFIG_SPI_FLASH_BAR
	#define CONFIG_SPI_FLASH_WINBOND
	#define CONFIG_SF_DEFAULT_BUS 0
	#define CONFIG_SF_DEFAULT_CS 0
	/* GPIO 3-19 (21248) */
	#define CONFIG_SF_DEFAULT_SPEED 30000000
	#define CONFIG_SF_DEFAULT_MODE (SPI_MODE_0)
	#endif

	#else
	/* Enable NAND support */
	#define CONFIG_CMD_TIME
	#define CONFIG_CMD_NAND
	#define CONFIG_CMD_NAND_TRIMFFS
	#ifdef CONFIG_CMD_NAND
	#define CONFIG_NAND_MXS
	#define CONFIG_SYS_MAX_NAND_DEVICE 1
	#define CONFIG_SYS_NAND_BASE 0x40000000
	#define CONFIG_SYS_NAND_5_ADDR_CYCLE
	#define CONFIG_SYS_NAND_ONFI_DETECTION

	/* DMA stuff, needed for GPMI/MXS NAND support */
	#define CONFIG_APBH_DMA
	#define CONFIG_APBH_DMA_BURST
	#define CONFIG_APBH_DMA_BURST8
	#endif

	#endif /* CONFIG_SPI_FLASH */

	/* Flattened Image Tree Suport */
	#define CONFIG_FIT
	#define CONFIG_FIT_VERBOSE

	/* I2C Configs */
	#define CONFIG_CMD_I2C
	#define CONFIG_SYS_I2C
	#define CONFIG_SYS_I2C_MXC
	#define CONFIG_SYS_I2C_SPEED 100000
	#define CONFIG_I2C_GSC 0
	#define CONFIG_I2C_PMIC 1

	/* MMC Configs */
	#define CONFIG_FSL_ESDHC
	#define CONFIG_FSL_USDHC
	#define CONFIG_SYS_FSL_ESDHC_ADDR 0
	#define CONFIG_SYS_FSL_USDHC_NUM 1
	#define CONFIG_MMC
	#define CONFIG_CMD_MMC
	#define CONFIG_GENERIC_MMC
	#define CONFIG_BOUNCE_BUFFER

	/* Filesystem support */
	#define CONFIG_CMD_EXT2
	#define CONFIG_CMD_FAT
	#define CONFIG_CMD_UBIFS
	#define CONFIG_DOS_PARTITION

	/*
	* SATA Configs
	*/
	#define CONFIG_CMD_SATA
	#ifdef CONFIG_CMD_SATA
	#define CONFIG_DWC_AHSATA
	#define CONFIG_SYS_SATA_MAX_DEVICE 1
	#define CONFIG_DWC_AHSATA_PORT_ID 0
	#define CONFIG_DWC_AHSATA_BASE_ADDR SATA_ARB_BASE_ADDR
	#define CONFIG_LBA48
	#define CONFIG_LIBATA
	#endif

	/*
	* PCI express
	*/
	#define CONFIG_CMD_PCI
	#ifdef CONFIG_CMD_PCI
	#define CONFIG_PCI
	#define CONFIG_PCI_PNP
	#define CONFIG_PCI_SCAN_SHOW
	#define CONFIG_PCI_FIXUP_DEV
	#define CONFIG_PCIE_IMX
	#endif

	/*
	* PMIC
	*/
	#define CONFIG_POWER
	#define CONFIG_POWER_I2C
	#define CONFIG_POWER_PFUZE100
	#define CONFIG_POWER_PFUZE100_I2C_ADDR 0x08
	#define CONFIG_POWER_LTC3676
	#define CONFIG_POWER_LTC3676_I2C_ADDR 0x3c

	/* Various command support */
	#include <config_cmd_default.h>
	#undef CONFIG_CMD_IMLS
	#define CONFIG_CMD_PING
	#define CONFIG_CMD_DHCP
	#define CONFIG_CMD_MII
	#define CONFIG_CMD_NET
	#define CONFIG_CMD_BMODE /* set eFUSE shadow for a boot dev and reset */
	#define CONFIG_CMD_HDMIDETECT /* detect HDMI output device */
	#define CONFIG_CMD_SETEXPR
	#define CONFIG_CMD_BOOTZ
	#define CONFIG_CMD_GSC
	#define CONFIG_CMD_EECONFIG /* Gateworks EEPROM config cmd */
	#define CONFIG_CMD_UBI
	#define CONFIG_RBTREE
	#define CONFIG_LZO
	#define CONFIG_CMD_FUSE /* eFUSE read/write support */
	#ifdef CONFIG_CMD_FUSE
	#define CONFIG_MXC_OCOTP
	#endif


	/* Ethernet support */
	#define CONFIG_FEC_MXC
	#define CONFIG_E1000
	#define CONFIG_MII
	#define IMX_FEC_BASE ENET_BASE_ADDR
	#define CONFIG_FEC_XCV_TYPE RGMII
	#define CONFIG_FEC_MXC_PHYADDR 0
	#define CONFIG_PHYLIB
	#define CONFIG_ARP_TIMEOUT 200UL

	/* USB Configs */
	#define CONFIG_CMD_USB
	#define CONFIG_USB_EHCI
	#define CONFIG_USB_EHCI_MX6
	#define CONFIG_USB_STORAGE
	#define CONFIG_USB_HOST_ETHER
	#define CONFIG_USB_ETHER_ASIX
	#define CONFIG_USB_ETHER_SMSC95XX
	#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
	#define CONFIG_EHCI_HCD_INIT_AFTER_RESET /* For OTG port */
	#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI \| PORT_PTS_PTW)
	#define CONFIG_MXC_USB_FLAGS 0
	#define CONFIG_USB_KEYBOARD
	#define CONFIG_CI_UDC
	#define CONFIG_USBD_HS
	#define CONFIG_USB_GADGET_DUALSPEED
	#define CONFIG_USB_ETHER
	#define CONFIG_USB_ETH_CDC
	#define CONFIG_NETCONSOLE
	#define CONFIG_SYS_USB_EVENT_POLL_VIA_CONTROL_EP

	/* USB Mass Storage Gadget */
	#define CONFIG_USB_GADGET
	#define CONFIG_CMD_USB_MASS_STORAGE
	#define CONFIG_USB_GADGET_MASS_STORAGE
	#define CONFIG_USBDOWNLOAD_GADGET
	#define CONFIG_USB_GADGET_VBUS_DRAW 2

	/* Netchip IDs */
	#define CONFIG_G_DNL_VENDOR_NUM 0x0525
	#define CONFIG_G_DNL_PRODUCT_NUM 0xa4a5
	#define CONFIG_G_DNL_MANUFACTURER "Gateworks"

	/* Framebuffer and LCD */
	#define CONFIG_VIDEO
	#define CONFIG_VIDEO_IPUV3
	#define CONFIG_CFB_CONSOLE
	#define CONFIG_VGA_AS_SINGLE_DEVICE
	#define CONFIG_SYS_CONSOLE_IS_IN_ENV
	#define CONFIG_VIDEO_BMP_RLE8
	#define CONFIG_SPLASH_SCREEN
	#define CONFIG_BMP_16BPP
	#define CONFIG_VIDEO_LOGO
	#define CONFIG_IPUV3_CLK 260000000
	#define CONFIG_CMD_HDMIDETECT
	#define CONFIG_CONSOLE_MUX
	#define CONFIG_IMX_HDMI
	#define CONFIG_IMX_VIDEO_SKIP

	/* serial console (ttymxc1,115200) */
	#define CONFIG_CONS_INDEX 1
	#define CONFIG_BAUDRATE 115200

	/* Miscellaneous configurable options */
	#define CONFIG_SYS_LONGHELP
	#define CONFIG_SYS_HUSH_PARSER
	#define CONFIG_SYS_PROMPT "Ventana > "
	#define CONFIG_SYS_CBSIZE 1024
	#define CONFIG_AUTO_COMPLETE
	#define CONFIG_CMDLINE_EDITING
	#define CONFIG_HWCONFIG

	/* Print Buffer Size */
	#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
	#define CONFIG_SYS_MAXARGS 16
	#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE

	/* Memory configuration */
	#define CONFIG_SYS_MEMTEST_START 0x10000000
	#define CONFIG_SYS_MEMTEST_END 0x10010000
	#define CONFIG_SYS_MEMTEST_SCRATCH 0x10800000
	#define CONFIG_SYS_TEXT_BASE 0x17800000
	#define CONFIG_SYS_LOAD_ADDR 0x12000000

	/* Physical Memory Map */
	#define CONFIG_NR_DRAM_BANKS 1
	#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
	#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
	#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
	#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE

	#define CONFIG_SYS_INIT_SP_OFFSET \
	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
	#define CONFIG_SYS_INIT_SP_ADDR \
	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)

	/* FLASH and environment organization */
	#define CONFIG_SYS_NO_FLASH /* no NOR flash */

	/*
	* MTD Command for mtdparts
	*/
	#define CONFIG_CMD_MTDPARTS
	#define CONFIG_MTD_DEVICE
	#define CONFIG_MTD_PARTITIONS
	#ifdef CONFIG_SPI_FLASH
	#define MTDIDS_DEFAULT "nor0=nor"
	#define MTDPARTS_DEFAULT \
	"mtdparts=nor:512k(uboot),64k(env),2m(kernel),-(rootfs)"
	#else
	#define MTDIDS_DEFAULT "nand0=nand"
	#define MTDPARTS_DEFAULT "mtdparts=nand:16m(uboot),1m(env),-(rootfs)"
	#endif

	/* Persistent Environment Config */
	#define CONFIG_ENV_OVERWRITE /* allow to overwrite serial and ethaddr */
	#ifdef CONFIG_SPI_FLASH
	#define CONFIG_ENV_IS_IN_SPI_FLASH
	#else
	#define CONFIG_ENV_IS_IN_NAND
	#endif
	#if defined(CONFIG_ENV_IS_IN_MMC)
	#define CONFIG_ENV_OFFSET (6 * 64 * 1024)
	#define CONFIG_ENV_SIZE (8 * 1024)
	#define CONFIG_SYS_MMC_ENV_DEV 0
	#elif defined(CONFIG_ENV_IS_IN_NAND)
	#define CONFIG_ENV_OFFSET (16 << 20)
	#define CONFIG_ENV_SECT_SIZE (128 << 10)
	#define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE
	#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + (512 << 10))
	#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
	#elif defined(CONFIG_ENV_IS_IN_SPI_FLASH)
	#define CONFIG_ENV_OFFSET (512 * 1024)
	#define CONFIG_ENV_SECT_SIZE (64 * 1024)
	#define CONFIG_ENV_SIZE (8 * 1024)
	#define CONFIG_ENV_SPI_BUS CONFIG_SF_DEFAULT_BUS
	#define CONFIG_ENV_SPI_CS CONFIG_SF_DEFAULT_CS
	#define CONFIG_ENV_SPI_MODE CONFIG_SF_DEFAULT_MODE
	#define CONFIG_ENV_SPI_MAX_HZ CONFIG_SF_DEFAULT_SPEED
	#endif

	/* Environment */
	#define CONFIG_BOOTDELAY 3
	#define CONFIG_LOADADDR CONFIG_SYS_LOAD_ADDR
	#define CONFIG_IPADDR 192.168.1.1
	#define CONFIG_SERVERIP 192.168.1.146
	#define HWCONFIG_DEFAULT \
	"hwconfig=rs232;" \
	"dio0:mode=gpio;dio1:mode=gpio;dio2:mode=gpio;dio3:mode=gpio\0" \

	#define CONFIG_EXTRA_ENV_SETTINGS_COMMON \
	"console=ttymxc1\0" \
	"bootdevs=usb mmc sata flash\0" \
	HWCONFIG_DEFAULT \
	"video=\0" \
	\
	"mtdparts=" MTDPARTS_DEFAULT "\0" \
	"mtdids=" MTDIDS_DEFAULT "\0" \
	\
	"fdt_high=0xffffffff\0" \
	"fdt_addr=0x18000000\0" \
	"initrd_high=0xffffffff\0" \
	"loadfdt=" \
	"if ${fsload} ${fdt_addr} boot/${fdt_file}; then " \
	"echo Loaded DTB from boot/${fdt_file}; " \
	"elif ${fsload} ${fdt_addr} boot/${fdt_file1}; then " \
	"echo Loaded DTB from boot/${fdt_file1}; " \
	"elif ${fsload} ${fdt_addr} boot/${fdt_file2}; then " \
	"echo Loaded DTB from boot/${fdt_file2}; " \
	"fi\0" \
	\
	"script=boot/6x_bootscript-ventana\0" \
	"loadscript=" \
	"if ${fsload} ${loadaddr} ${script}; then " \
	"source; " \
	"fi\0" \
	\
	"uimage=boot/uImage\0" \
	"mmc_root=/dev/mmcblk0p1 rootfstype=ext4 rootwait rw\0" \
	"mmc_boot=" \
	"setenv fsload 'ext2load mmc 0:1'; " \
	"mmc dev 0 && mmc rescan && " \
	"run loadscript; " \
	"if ${fsload} ${loadaddr} ${uimage}; then " \
	"setenv bootargs console=${console},${baudrate} " \
	"root=/dev/mmcblk0p1 rootfstype=ext4 " \
	"rootwait rw ${video} ${extra}; " \
	"if run loadfdt && fdt addr ${fdt_addr}; then " \
	"bootm ${loadaddr} - ${fdt_addr}; " \
	"else " \
	"bootm; " \
	"fi; " \
	"fi\0" \
	\
	"sata_boot=" \
	"setenv fsload 'ext2load sata 0:1'; sata init && " \
	"run loadscript; " \
	"if ${fsload} ${loadaddr} ${uimage}; then " \
	"setenv bootargs console=${console},${baudrate} " \
	"root=/dev/sda1 rootfstype=ext4 " \
	"rootwait rw ${video} ${extra}; " \
	"if run loadfdt && fdt addr ${fdt_addr}; then " \
	"bootm ${loadaddr} - ${fdt_addr}; " \
	"else " \
	"bootm; " \
	"fi; " \
	"fi\0" \
	"usb_boot=" \
	"setenv fsload 'ext2load usb 0:1'; usb start && usb dev 0 && " \
	"run loadscript; " \
	"if ${fsload} ${loadaddr} ${uimage}; then " \
	"setenv bootargs console=${console},${baudrate} " \
	"root=/dev/sda1 rootfstype=ext4 " \
	"rootwait rw ${video} ${extra}; " \
	"if run loadfdt && fdt addr ${fdt_addr}; then " \
	"bootm ${loadaddr} - ${fdt_addr}; " \
	"else " \
	"bootm; " \
	"fi; " \
	"fi\0"

	#ifdef CONFIG_SPI_FLASH
	#define CONFIG_EXTRA_ENV_SETTINGS \
	CONFIG_EXTRA_ENV_SETTINGS_COMMON \
	"image_os=ventana/openwrt-imx6-imx6q-gw5400-a-squashfs.bin\0" \
	"image_uboot=ventana/u-boot_spi.imx\0" \
	\
	"spi_koffset=0x90000\0" \
	"spi_klen=0x200000\0" \
	\
	"spi_updateuboot=echo Updating uboot from " \
	"${serverip}:${image_uboot}...; " \
	"tftpboot ${loadaddr} ${image_uboot} && " \
	"sf probe && sf erase 0 80000 && " \
	"sf write ${loadaddr} 400 ${filesize}\0" \
	"spi_update=echo Updating OS from ${serverip}:${image_os} " \
	"to ${spi_koffset} ...; " \
	"tftp ${loadaddr} ${image_os} && " \
	"sf probe && " \
	"sf update ${loadaddr} ${spi_koffset} ${filesize}\0" \
	\
	"flash_boot=" \
	"if sf probe && " \
	"sf read ${loadaddr} ${spi_koffset} ${spi_klen}; then " \
	"setenv bootargs console=${console},${baudrate} " \
	"root=/dev/mtdblock3 " \
	"rootfstype=squashfs,jffs2 " \
	"${video} ${extra}; " \
	"bootm; " \
	"fi\0"
	#else
	#define CONFIG_EXTRA_ENV_SETTINGS \
	CONFIG_EXTRA_ENV_SETTINGS_COMMON \
	"image_rootfs=openwrt-imx6-ventana-rootfs.ubi\0" \
	\
	"nand_update=echo Updating NAND from ${serverip}:${image_rootfs}...; " \
	"tftp ${loadaddr} ${image_rootfs} && " \
	"nand erase.part rootfs && " \
	"nand write ${loadaddr} rootfs ${filesize}\0" \
	\
	"flash_boot=" \
	"setenv fsload 'ubifsload'; " \
	"ubi part rootfs && ubifsmount ubi0:rootfs; " \
	"run loadscript; " \
	"if ${fsload} ${loadaddr} ${uimage}; then " \
	"setenv bootargs console=${console},${baudrate} " \
	"root=ubi0:rootfs ubi.mtd=2 " \
	"rootfstype=ubifs ${video} ${extra}; " \
	"if run loadfdt && fdt addr ${fdt_addr}; then " \
	"ubifsumount; " \
	"bootm ${loadaddr} - ${fdt_addr}; " \
	"else " \
	"ubifsumount; bootm; " \
	"fi; " \
	"fi\0"
	#endif

	#define CONFIG_BOOTCOMMAND \
	"for btype in ${bootdevs}; do " \
	"echo; echo Attempting ${btype} boot...; " \
	"if run ${btype}_boot; then; fi; " \
	"done"

	/* Device Tree Support */
	#define CONFIG_OF_BOARD_SETUP
	#define CONFIG_OF_LIBFDT
	#define CONFIG_FDT_FIXUP_PARTITIONS

	#ifndef CONFIG_SYS_DCACHE_OFF
	#define CONFIG_CMD_CACHE
	#endif

	#endif /* __CONFIG_H */