| /* SPDX-License-Identifier: GPL-2.0+ */ |
| /* |
| * Bluewater Systems Snapper 9260 and 9G20 modules |
| * |
| * (C) Copyright 2011 Bluewater Systems |
| * Author: Andre Renaud <andre@bluewatersys.com> |
| * Author: Ryan Mallon <ryan@bluewatersys.com> |
| */ |
| |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| /* SoC type is defined in boards.cfg */ |
| #include <asm/hardware.h> |
| #include <linux/sizes.h> |
| |
| /* ARM asynchronous clock */ |
| #define CONFIG_SYS_AT91_MAIN_CLOCK 18432000 /* External Crystal, in Hz */ |
| #define CONFIG_SYS_AT91_SLOW_CLOCK 32768 |
| |
| /* CPU */ |
| |
| /* SDRAM */ |
| #define CONFIG_SYS_SDRAM_BASE ATMEL_BASE_CS1 |
| #define CONFIG_SYS_SDRAM_SIZE (64 * 1024 * 1024) /* 64MB */ |
| #define CONFIG_SYS_INIT_SP_ADDR (ATMEL_BASE_SRAM1 + 0x1000 - \ |
| GENERATED_GBL_DATA_SIZE) |
| |
| /* Mem test settings */ |
| |
| /* NAND Flash */ |
| #define CONFIG_SYS_MAX_NAND_DEVICE 1 |
| #define CONFIG_SYS_NAND_BASE ATMEL_BASE_CS3 |
| #define CONFIG_SYS_NAND_DBW_8 |
| #define CONFIG_SYS_NAND_MASK_ALE (1 << 21) /* AD21 */ |
| #define CONFIG_SYS_NAND_MASK_CLE (1 << 22) /* AD22 */ |
| #define CONFIG_SYS_NAND_ENABLE_PIN AT91_PIN_PC14 |
| #define CONFIG_SYS_NAND_READY_PIN AT91_PIN_PC13 |
| |
| /* Ethernet */ |
| #define CONFIG_RMII |
| #define CONFIG_RESET_PHY_R |
| #define CONFIG_AT91_WANTS_COMMON_PHY |
| #define CONFIG_TFTP_PORT |
| |
| /* USB */ |
| #define CONFIG_USB_ATMEL |
| #define CONFIG_USB_ATMEL_CLK_SEL_PLLB |
| #define CONFIG_USB_OHCI_NEW |
| #define CONFIG_SYS_USB_OHCI_CPU_INIT |
| #define CONFIG_SYS_USB_OHCI_REGS_BASE ATMEL_UHP_BASE |
| #define CONFIG_SYS_USB_OHCI_SLOT_NAME "at91sam9260" |
| #define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 2 |
| |
| /* GPIOs and IO expander */ |
| #define CONFIG_ATMEL_LEGACY |
| #define CONFIG_PCA953X |
| #define CONFIG_SYS_I2C_PCA953X_ADDR 0x28 |
| #define CONFIG_SYS_I2C_PCA953X_WIDTH { {0x28, 16} } |
| |
| /* UARTs/Serial console */ |
| #ifndef CONFIG_DM_SERIAL |
| #define CONFIG_USART_BASE ATMEL_BASE_DBGU |
| #define CONFIG_USART_ID ATMEL_ID_SYS |
| #endif |
| |
| /* I2C - Bit-bashed */ |
| #define CONFIG_SOFT_I2C_READ_REPEATED_START |
| #define I2C_INIT do { \ |
| at91_set_gpio_output(AT91_PIN_PA23, 1); \ |
| at91_set_gpio_output(AT91_PIN_PA24, 1); \ |
| at91_set_pio_multi_drive(AT91_PIO_PORTA, 23, 1); \ |
| at91_set_pio_multi_drive(AT91_PIO_PORTA, 24, 1); \ |
| } while (0) |
| #define I2C_SOFT_DECLARATIONS |
| #define I2C_ACTIVE |
| #define I2C_TRISTATE at91_set_gpio_input(AT91_PIN_PA23, 1); |
| #define I2C_READ at91_get_gpio_value(AT91_PIN_PA23); |
| #define I2C_SDA(bit) do { \ |
| if (bit) { \ |
| at91_set_gpio_input(AT91_PIN_PA23, 1); \ |
| } else { \ |
| at91_set_gpio_output(AT91_PIN_PA23, 1); \ |
| at91_set_gpio_value(AT91_PIN_PA23, bit); \ |
| } \ |
| } while (0) |
| #define I2C_SCL(bit) at91_set_pio_value(AT91_PIO_PORTA, 24, bit) |
| #define I2C_DELAY udelay(2) |
| |
| /* Boot options */ |
| |
| /* Environment settings */ |
| |
| /* Console settings */ |
| |
| #endif /* __CONFIG_H */ |