drivers/usb/dwc3/ti_usb_phy.c - filogic/uboot - Gitiles

 // SPDX-License-Identifier: GPL-2.0+
 /**
  * ti_usb_phy.c - USB3 and USB3 PHY programming for dwc3
  *
  * Copyright (C) 2015 Texas Instruments Incorporated - http://www.ti.com
  *
  * Author: Kishon Vijay Abraham I <kishon@ti.com>
  *
  * Taken from Linux Kernel v3.16 (drivers/phy/phy-ti-pipe3.c and
  * drivers/phy/phy-omap-usb2.c) and ported to uboot.
  *
  * "commit 56042e : phy: ti-pipe3: Fix suspend/resume and module reload" for
  * phy-ti-pipe3.c
  *
  * "commit eb82a3 : phy: omap-usb2: Balance pm_runtime_enable() on probe failure
  * and remove" for phy-omap-usb2.c
  */

 #include <common.h>
 #include <malloc.h>
 #include <ti-usb-phy-uboot.h>
 #include <dm/device_compat.h>
 #include <dm/devres.h>
 #include <linux/bitops.h>
 #include <linux/delay.h>
 #include <linux/ioport.h>
 #include <asm/io.h>
 #include <asm/arch/sys_proto.h>
 #include <dm.h>

 #include "linux-compat.h"

 #define PLL_STATUS		0x00000004
 #define PLL_GO			0x00000008
 #define PLL_CONFIGURATION1	0x0000000C
 #define PLL_CONFIGURATION2	0x00000010
 #define PLL_CONFIGURATION3	0x00000014
 #define PLL_CONFIGURATION4	0x00000020

 #define PLL_REGM_MASK		0x001FFE00
 #define PLL_REGM_SHIFT		0x9
 #define PLL_REGM_F_MASK		0x0003FFFF
 #define PLL_REGM_F_SHIFT	0x0
 #define PLL_REGN_MASK		0x000001FE
 #define PLL_REGN_SHIFT		0x1
 #define PLL_SELFREQDCO_MASK	0x0000000E
 #define PLL_SELFREQDCO_SHIFT	0x1
 #define PLL_SD_MASK		0x0003FC00
 #define PLL_SD_SHIFT		10
 #define SET_PLL_GO		0x1
 #define PLL_LDOPWDN		BIT(15)
 #define PLL_TICOPWDN		BIT(16)
 #define PLL_LOCK		0x2
 #define PLL_IDLE		0x1

 #define OMAP_CTRL_DEV_PHY_PD				BIT(0)
 #define OMAP_CTRL_USB3_PHY_PWRCTL_CLK_CMD_MASK		0x003FC000
 #define OMAP_CTRL_USB3_PHY_PWRCTL_CLK_CMD_SHIFT		0xE

 #define OMAP_CTRL_USB3_PHY_PWRCTL_CLK_FREQ_MASK		0xFFC00000
 #define OMAP_CTRL_USB3_PHY_PWRCTL_CLK_FREQ_SHIFT	0x16

 #define OMAP_CTRL_USB3_PHY_TX_RX_POWERON	0x3
 #define OMAP_CTRL_USB3_PHY_TX_RX_POWEROFF	0x0

 #define OMAP_CTRL_USB2_PHY_PD			BIT(28)

 #define AM437X_CTRL_USB2_PHY_PD			BIT(0)
 #define AM437X_CTRL_USB2_OTG_PD			BIT(1)
 #define AM437X_CTRL_USB2_OTGVDET_EN		BIT(19)
 #define AM437X_CTRL_USB2_OTGSESSEND_EN		BIT(20)

 static LIST_HEAD(ti_usb_phy_list);
 typedef unsigned int u32;

 struct usb3_dpll_params {
 	u16	m;
 	u8	n;
 	u8	freq:3;
 	u8	sd;
 	u32	mf;
 };

 struct usb3_dpll_map {
 	unsigned long rate;
 	struct usb3_dpll_params params;
 	struct usb3_dpll_map *dpll_map;
 };

 struct ti_usb_phy {
 	void __iomem *pll_ctrl_base;
 	void __iomem *usb2_phy_power;
 	void __iomem *usb3_phy_power;
 	struct usb3_dpll_map *dpll_map;
 	struct list_head list;
 	int index;
 };

 static struct usb3_dpll_map dpll_map_usb[] = {
 	{12000000, {1250, 5, 4, 20, 0} },	/* 12 MHz */
 	{16800000, {3125, 20, 4, 20, 0} },	/* 16.8 MHz */
 	{19200000, {1172, 8, 4, 20, 65537} },	/* 19.2 MHz */
 	{20000000, {1000, 7, 4, 10, 0} },	/* 20 MHz */
 	{26000000, {1250, 12, 4, 20, 0} },	/* 26 MHz */
 	{38400000, {3125, 47, 4, 20, 92843} },	/* 38.4 MHz */
 	{ },					/* Terminator */
 };

 static inline unsigned int ti_usb3_readl(void __iomem *base, u32 offset)
 {
 	return readl(base + offset);
 }

 static inline void ti_usb3_writel(void __iomem *base, u32 offset, u32 value)
 {
 	writel(value, base + offset);
 }

 #ifndef CONFIG_AM43XX
 static struct usb3_dpll_params *ti_usb3_get_dpll_params(struct ti_usb_phy *phy)
 {
 	unsigned long rate;
 	struct usb3_dpll_map *dpll_map = phy->dpll_map;

 	rate = get_sys_clk_freq();

 	for (; dpll_map->rate; dpll_map++) {
 		if (rate == dpll_map->rate)
 			return &dpll_map->params;
 	}

 	log_err("No DPLL configuration for %lu Hz SYS CLK\n", rate);

 	return NULL;
 }

 static int ti_usb3_dpll_wait_lock(struct ti_usb_phy *phy)
 {
 	u32 val;
 	do {
 		val = ti_usb3_readl(phy->pll_ctrl_base, PLL_STATUS);
 			if (val & PLL_LOCK)
 				break;
 	} while (1);

 	return 0;
 }

 static int ti_usb3_dpll_program(struct ti_usb_phy *phy)
 {
 	u32			val;
 	struct usb3_dpll_params	*dpll_params;

 	if (!phy->pll_ctrl_base)
 		return -EINVAL;

 	dpll_params = ti_usb3_get_dpll_params(phy);
 	if (!dpll_params)
 		return -EINVAL;

 	val = ti_usb3_readl(phy->pll_ctrl_base, PLL_CONFIGURATION1);
 	val &= ~PLL_REGN_MASK;
 	val |= dpll_params->n << PLL_REGN_SHIFT;
 	ti_usb3_writel(phy->pll_ctrl_base, PLL_CONFIGURATION1, val);

 	val = ti_usb3_readl(phy->pll_ctrl_base, PLL_CONFIGURATION2);
 	val &= ~PLL_SELFREQDCO_MASK;
 	val |= dpll_params->freq << PLL_SELFREQDCO_SHIFT;
 	ti_usb3_writel(phy->pll_ctrl_base, PLL_CONFIGURATION2, val);

 	val = ti_usb3_readl(phy->pll_ctrl_base, PLL_CONFIGURATION1);
 	val &= ~PLL_REGM_MASK;
 	val |= dpll_params->m << PLL_REGM_SHIFT;
 	ti_usb3_writel(phy->pll_ctrl_base, PLL_CONFIGURATION1, val);

 	val = ti_usb3_readl(phy->pll_ctrl_base, PLL_CONFIGURATION4);
 	val &= ~PLL_REGM_F_MASK;
 	val |= dpll_params->mf << PLL_REGM_F_SHIFT;
 	ti_usb3_writel(phy->pll_ctrl_base, PLL_CONFIGURATION4, val);

 	val = ti_usb3_readl(phy->pll_ctrl_base, PLL_CONFIGURATION3);
 	val &= ~PLL_SD_MASK;
 	val |= dpll_params->sd << PLL_SD_SHIFT;
 	ti_usb3_writel(phy->pll_ctrl_base, PLL_CONFIGURATION3, val);

 	ti_usb3_writel(phy->pll_ctrl_base, PLL_GO, SET_PLL_GO);

 	return ti_usb3_dpll_wait_lock(phy);
 }
 #endif

 void ti_usb2_phy_power(struct ti_usb_phy *phy, int on)
 {
 	u32 val;

 	val = readl(phy->usb2_phy_power);

 	if (on) {
 #if defined(CONFIG_DRA7XX)
 		if (phy->index == 1)
 			val &= ~OMAP_CTRL_USB2_PHY_PD;
 		else
 			val &= ~OMAP_CTRL_DEV_PHY_PD;
 #elif defined(CONFIG_AM43XX)
 		val &= ~(AM437X_CTRL_USB2_PHY_PD |
 			 AM437X_CTRL_USB2_OTG_PD);
 		val |= (AM437X_CTRL_USB2_OTGVDET_EN |
 			AM437X_CTRL_USB2_OTGSESSEND_EN);
 #endif
 	} else {
 #if defined(CONFIG_DRA7XX)
 		if (phy->index == 1)
 			val |= OMAP_CTRL_USB2_PHY_PD;
 		else
 			val |= OMAP_CTRL_DEV_PHY_PD;

 #elif defined(CONFIG_AM43XX)
 		val &= ~(AM437X_CTRL_USB2_OTGVDET_EN |
 			 AM437X_CTRL_USB2_OTGSESSEND_EN);
 		val |= (AM437X_CTRL_USB2_PHY_PD |
 			AM437X_CTRL_USB2_OTG_PD);
 #endif
 	}
 	writel(val, phy->usb2_phy_power);
 }

 #ifndef CONFIG_AM43XX
 void ti_usb3_phy_power(struct ti_usb_phy *phy, int on)
 {
 	u32 val;
 	u32 rate;
 	rate = get_sys_clk_freq();
 	rate = rate/1000000;

 	if (!phy->usb3_phy_power)
 		return;

 	val = readl(phy->usb3_phy_power);
 	if (on) {
 		val &= ~(OMAP_CTRL_USB3_PHY_PWRCTL_CLK_CMD_MASK |
 			OMAP_CTRL_USB3_PHY_PWRCTL_CLK_FREQ_MASK);
 		val |= (OMAP_CTRL_USB3_PHY_TX_RX_POWERON) <<
 			OMAP_CTRL_USB3_PHY_PWRCTL_CLK_CMD_SHIFT;
 		val |= rate <<
 			OMAP_CTRL_USB3_PHY_PWRCTL_CLK_FREQ_SHIFT;
 	} else {
 		val &= ~OMAP_CTRL_USB3_PHY_PWRCTL_CLK_CMD_MASK;
 		val |= OMAP_CTRL_USB3_PHY_TX_RX_POWEROFF <<
 			OMAP_CTRL_USB3_PHY_PWRCTL_CLK_CMD_SHIFT;
 	}
 	writel(val, phy->usb3_phy_power);
 }
 #endif

 /**
  * ti_usb_phy_uboot_init - usb phy uboot initialization code
  * @dev: struct ti_usb_phy_device containing initialization data
  *
  * Entry point for ti usb phy driver. This driver handles initialization
  * of both usb2 phy and usb3 phy. Pointer to ti_usb_phy_device should be
  * passed containing base address and other initialization data.
  * Returns '0' on success and a negative value on failure.
  *
  * Generally called from board_usb_init() implemented in board file.
  */
 int ti_usb_phy_uboot_init(struct ti_usb_phy_device *dev)
 {
 	struct ti_usb_phy *phy;

 	phy = devm_kzalloc(NULL, sizeof(*phy), GFP_KERNEL);
 	if (!phy) {
 		log_err("unable to alloc mem for TI USB3 PHY\n");
 		return -ENOMEM;
 	}

 	phy->dpll_map = dpll_map_usb;
 	phy->index = dev->index;
 	phy->pll_ctrl_base = dev->pll_ctrl_base;
 	phy->usb2_phy_power = dev->usb2_phy_power;
 	phy->usb3_phy_power = dev->usb3_phy_power;

 #ifndef CONFIG_AM43XX
 	ti_usb3_dpll_program(phy);
 	ti_usb3_phy_power(phy, 1);
 #endif
 	ti_usb2_phy_power(phy, 1);
 	mdelay(150);
 	list_add_tail(&phy->list, &ti_usb_phy_list);

 	return 0;
 }

 /**
  * ti_usb_phy_uboot_exit - usb phy uboot cleanup code
  * @index: index of this controller
  *
  * Performs cleanup of memory allocated in ti_usb_phy_uboot_init.
  * index of _this_ controller should be passed and should match with
  * the index passed in ti_usb_phy_device during init.
  *
  * Generally called from board file.
  */
 void ti_usb_phy_uboot_exit(int index)
 {
 	struct ti_usb_phy *phy = NULL;

 	list_for_each_entry(phy, &ti_usb_phy_list, list) {
 		if (phy->index != index)
 			continue;

 		ti_usb2_phy_power(phy, 0);
 #ifndef CONFIG_AM43XX
 		ti_usb3_phy_power(phy, 0);
 #endif
 		list_del(&phy->list);
 		kfree(phy);
 		break;
 	}
 }
	// SPDX-License-Identifier: GPL-2.0+
	/**
	* ti_usb_phy.c - USB3 and USB3 PHY programming for dwc3
	*
	* Copyright (C) 2015 Texas Instruments Incorporated - http://www.ti.com
	*
	* Author: Kishon Vijay Abraham I <kishon@ti.com>
	*
	* Taken from Linux Kernel v3.16 (drivers/phy/phy-ti-pipe3.c and
	* drivers/phy/phy-omap-usb2.c) and ported to uboot.
	*
	* "commit 56042e : phy: ti-pipe3: Fix suspend/resume and module reload" for
	* phy-ti-pipe3.c
	*
	* "commit eb82a3 : phy: omap-usb2: Balance pm_runtime_enable() on probe failure
	* and remove" for phy-omap-usb2.c
	*/

	#include <common.h>
	#include <malloc.h>
	#include <ti-usb-phy-uboot.h>
	#include <dm/device_compat.h>
	#include <dm/devres.h>
	#include <linux/bitops.h>
	#include <linux/delay.h>
	#include <linux/ioport.h>
	#include <asm/io.h>
	#include <asm/arch/sys_proto.h>
	#include <dm.h>

	#include "linux-compat.h"

	#define PLL_STATUS 0x00000004
	#define PLL_GO 0x00000008
	#define PLL_CONFIGURATION1 0x0000000C
	#define PLL_CONFIGURATION2 0x00000010
	#define PLL_CONFIGURATION3 0x00000014
	#define PLL_CONFIGURATION4 0x00000020

	#define PLL_REGM_MASK 0x001FFE00
	#define PLL_REGM_SHIFT 0x9
	#define PLL_REGM_F_MASK 0x0003FFFF
	#define PLL_REGM_F_SHIFT 0x0
	#define PLL_REGN_MASK 0x000001FE
	#define PLL_REGN_SHIFT 0x1
	#define PLL_SELFREQDCO_MASK 0x0000000E
	#define PLL_SELFREQDCO_SHIFT 0x1
	#define PLL_SD_MASK 0x0003FC00
	#define PLL_SD_SHIFT 10
	#define SET_PLL_GO 0x1
	#define PLL_LDOPWDN BIT(15)
	#define PLL_TICOPWDN BIT(16)
	#define PLL_LOCK 0x2
	#define PLL_IDLE 0x1

	#define OMAP_CTRL_DEV_PHY_PD BIT(0)
	#define OMAP_CTRL_USB3_PHY_PWRCTL_CLK_CMD_MASK 0x003FC000
	#define OMAP_CTRL_USB3_PHY_PWRCTL_CLK_CMD_SHIFT 0xE

	#define OMAP_CTRL_USB3_PHY_PWRCTL_CLK_FREQ_MASK 0xFFC00000
	#define OMAP_CTRL_USB3_PHY_PWRCTL_CLK_FREQ_SHIFT 0x16

	#define OMAP_CTRL_USB3_PHY_TX_RX_POWERON 0x3
	#define OMAP_CTRL_USB3_PHY_TX_RX_POWEROFF 0x0

	#define OMAP_CTRL_USB2_PHY_PD BIT(28)

	#define AM437X_CTRL_USB2_PHY_PD BIT(0)
	#define AM437X_CTRL_USB2_OTG_PD BIT(1)
	#define AM437X_CTRL_USB2_OTGVDET_EN BIT(19)
	#define AM437X_CTRL_USB2_OTGSESSEND_EN BIT(20)

	static LIST_HEAD(ti_usb_phy_list);
	typedef unsigned int u32;

	struct usb3_dpll_params {
	u16 m;
	u8 n;
	u8 freq:3;
	u8 sd;
	u32 mf;
	};

	struct usb3_dpll_map {
	unsigned long rate;
	struct usb3_dpll_params params;
	struct usb3_dpll_map *dpll_map;
	};

	struct ti_usb_phy {
	void __iomem *pll_ctrl_base;
	void __iomem *usb2_phy_power;
	void __iomem *usb3_phy_power;
	struct usb3_dpll_map *dpll_map;
	struct list_head list;
	int index;
	};

	static struct usb3_dpll_map dpll_map_usb[] = {
	{12000000, {1250, 5, 4, 20, 0} }, /* 12 MHz */
	{16800000, {3125, 20, 4, 20, 0} }, /* 16.8 MHz */
	{19200000, {1172, 8, 4, 20, 65537} }, /* 19.2 MHz */
	{20000000, {1000, 7, 4, 10, 0} }, /* 20 MHz */
	{26000000, {1250, 12, 4, 20, 0} }, /* 26 MHz */
	{38400000, {3125, 47, 4, 20, 92843} }, /* 38.4 MHz */
	{ }, /* Terminator */
	};

	static inline unsigned int ti_usb3_readl(void __iomem *base, u32 offset)
	{
	return readl(base + offset);
	}

	static inline void ti_usb3_writel(void __iomem *base, u32 offset, u32 value)
	{
	writel(value, base + offset);
	}

	#ifndef CONFIG_AM43XX
	static struct usb3_dpll_params ti_usb3_get_dpll_params(struct ti_usb_phy phy)
	{
	unsigned long rate;
	struct usb3_dpll_map *dpll_map = phy->dpll_map;

	rate = get_sys_clk_freq();

	for (; dpll_map->rate; dpll_map++) {
	if (rate == dpll_map->rate)
	return &dpll_map->params;
	}

	log_err("No DPLL configuration for %lu Hz SYS CLK\n", rate);

	return NULL;
	}

	static int ti_usb3_dpll_wait_lock(struct ti_usb_phy *phy)
	{
	u32 val;
	do {
	val = ti_usb3_readl(phy->pll_ctrl_base, PLL_STATUS);
	if (val & PLL_LOCK)
	break;
	} while (1);

	return 0;
	}

	static int ti_usb3_dpll_program(struct ti_usb_phy *phy)
	{
	u32 val;
	struct usb3_dpll_params *dpll_params;

	if (!phy->pll_ctrl_base)
	return -EINVAL;

	dpll_params = ti_usb3_get_dpll_params(phy);
	if (!dpll_params)
	return -EINVAL;

	val = ti_usb3_readl(phy->pll_ctrl_base, PLL_CONFIGURATION1);
	val &= ~PLL_REGN_MASK;
	val \|= dpll_params->n << PLL_REGN_SHIFT;
	ti_usb3_writel(phy->pll_ctrl_base, PLL_CONFIGURATION1, val);

	val = ti_usb3_readl(phy->pll_ctrl_base, PLL_CONFIGURATION2);
	val &= ~PLL_SELFREQDCO_MASK;
	val \|= dpll_params->freq << PLL_SELFREQDCO_SHIFT;
	ti_usb3_writel(phy->pll_ctrl_base, PLL_CONFIGURATION2, val);

	val = ti_usb3_readl(phy->pll_ctrl_base, PLL_CONFIGURATION1);
	val &= ~PLL_REGM_MASK;
	val \|= dpll_params->m << PLL_REGM_SHIFT;
	ti_usb3_writel(phy->pll_ctrl_base, PLL_CONFIGURATION1, val);

	val = ti_usb3_readl(phy->pll_ctrl_base, PLL_CONFIGURATION4);
	val &= ~PLL_REGM_F_MASK;
	val \|= dpll_params->mf << PLL_REGM_F_SHIFT;
	ti_usb3_writel(phy->pll_ctrl_base, PLL_CONFIGURATION4, val);

	val = ti_usb3_readl(phy->pll_ctrl_base, PLL_CONFIGURATION3);
	val &= ~PLL_SD_MASK;
	val \|= dpll_params->sd << PLL_SD_SHIFT;
	ti_usb3_writel(phy->pll_ctrl_base, PLL_CONFIGURATION3, val);

	ti_usb3_writel(phy->pll_ctrl_base, PLL_GO, SET_PLL_GO);

	return ti_usb3_dpll_wait_lock(phy);
	}
	#endif

	void ti_usb2_phy_power(struct ti_usb_phy *phy, int on)
	{
	u32 val;

	val = readl(phy->usb2_phy_power);

	if (on) {
	#if defined(CONFIG_DRA7XX)
	if (phy->index == 1)
	val &= ~OMAP_CTRL_USB2_PHY_PD;
	else
	val &= ~OMAP_CTRL_DEV_PHY_PD;
	#elif defined(CONFIG_AM43XX)
	val &= ~(AM437X_CTRL_USB2_PHY_PD \|
	AM437X_CTRL_USB2_OTG_PD);
	val \|= (AM437X_CTRL_USB2_OTGVDET_EN \|
	AM437X_CTRL_USB2_OTGSESSEND_EN);
	#endif
	} else {
	#if defined(CONFIG_DRA7XX)
	if (phy->index == 1)
	val \|= OMAP_CTRL_USB2_PHY_PD;
	else
	val \|= OMAP_CTRL_DEV_PHY_PD;

	#elif defined(CONFIG_AM43XX)
	val &= ~(AM437X_CTRL_USB2_OTGVDET_EN \|
	AM437X_CTRL_USB2_OTGSESSEND_EN);
	val \|= (AM437X_CTRL_USB2_PHY_PD \|
	AM437X_CTRL_USB2_OTG_PD);
	#endif
	}
	writel(val, phy->usb2_phy_power);
	}

	#ifndef CONFIG_AM43XX
	void ti_usb3_phy_power(struct ti_usb_phy *phy, int on)
	{
	u32 val;
	u32 rate;
	rate = get_sys_clk_freq();
	rate = rate/1000000;

	if (!phy->usb3_phy_power)
	return;

	val = readl(phy->usb3_phy_power);
	if (on) {
	val &= ~(OMAP_CTRL_USB3_PHY_PWRCTL_CLK_CMD_MASK \|
	OMAP_CTRL_USB3_PHY_PWRCTL_CLK_FREQ_MASK);
	val \|= (OMAP_CTRL_USB3_PHY_TX_RX_POWERON) <<
	OMAP_CTRL_USB3_PHY_PWRCTL_CLK_CMD_SHIFT;
	val \|= rate <<
	OMAP_CTRL_USB3_PHY_PWRCTL_CLK_FREQ_SHIFT;
	} else {
	val &= ~OMAP_CTRL_USB3_PHY_PWRCTL_CLK_CMD_MASK;
	val \|= OMAP_CTRL_USB3_PHY_TX_RX_POWEROFF <<
	OMAP_CTRL_USB3_PHY_PWRCTL_CLK_CMD_SHIFT;
	}
	writel(val, phy->usb3_phy_power);
	}
	#endif

	/**
	* ti_usb_phy_uboot_init - usb phy uboot initialization code
	* @dev: struct ti_usb_phy_device containing initialization data
	*
	* Entry point for ti usb phy driver. This driver handles initialization
	* of both usb2 phy and usb3 phy. Pointer to ti_usb_phy_device should be
	* passed containing base address and other initialization data.
	* Returns '0' on success and a negative value on failure.
	*
	* Generally called from board_usb_init() implemented in board file.
	*/
	int ti_usb_phy_uboot_init(struct ti_usb_phy_device *dev)
	{
	struct ti_usb_phy *phy;

	phy = devm_kzalloc(NULL, sizeof(*phy), GFP_KERNEL);
	if (!phy) {
	log_err("unable to alloc mem for TI USB3 PHY\n");
	return -ENOMEM;
	}

	phy->dpll_map = dpll_map_usb;
	phy->index = dev->index;
	phy->pll_ctrl_base = dev->pll_ctrl_base;
	phy->usb2_phy_power = dev->usb2_phy_power;
	phy->usb3_phy_power = dev->usb3_phy_power;

	#ifndef CONFIG_AM43XX
	ti_usb3_dpll_program(phy);
	ti_usb3_phy_power(phy, 1);
	#endif
	ti_usb2_phy_power(phy, 1);
	mdelay(150);
	list_add_tail(&phy->list, &ti_usb_phy_list);

	return 0;
	}

	/**
	* ti_usb_phy_uboot_exit - usb phy uboot cleanup code
	* @index: index of this controller
	*
	* Performs cleanup of memory allocated in ti_usb_phy_uboot_init.
	* index of _this_ controller should be passed and should match with
	* the index passed in ti_usb_phy_device during init.
	*
	* Generally called from board file.
	*/
	void ti_usb_phy_uboot_exit(int index)
	{
	struct ti_usb_phy *phy = NULL;

	list_for_each_entry(phy, &ti_usb_phy_list, list) {
	if (phy->index != index)
	continue;

	ti_usb2_phy_power(phy, 0);
	#ifndef CONFIG_AM43XX
	ti_usb3_phy_power(phy, 0);
	#endif
	list_del(&phy->list);
	kfree(phy);
	break;
	}
	}