board/freescale/ls1028a/ls1028a.c - filogic/uboot - Gitiles

 // SPDX-License-Identifier: GPL-2.0+
 /*
  * Copyright 2019, 2021 NXP
  */

 #include <common.h>
 #include <init.h>
 #include <malloc.h>
 #include <errno.h>
 #include <fsl_ddr.h>
 #include <net.h>
 #include <asm/global_data.h>
 #include <asm/io.h>
 #include <hwconfig.h>
 #include <fdt_support.h>
 #include <linux/libfdt.h>
 #include <env_internal.h>
 #include <asm/arch-fsl-layerscape/soc.h>
 #include <asm/arch-fsl-layerscape/fsl_icid.h>
 #include <i2c.h>
 #include <asm/arch/soc.h>
 #ifdef CONFIG_FSL_LS_PPA
 #include <asm/arch/ppa.h>
 #endif
 #include <fsl_immap.h>
 #include <netdev.h>

 #include <fdtdec.h>
 #include <miiphy.h>
 #include "../common/qixis.h"
 #include "../drivers/net/fsl_enetc.h"

 DECLARE_GLOBAL_DATA_PTR;

 int config_board_mux(void)
 {
 #ifndef CONFIG_LPUART
 #if defined(CONFIG_TARGET_LS1028AQDS) && defined(CONFIG_FSL_QIXIS)
 	u8 reg;

 	reg = QIXIS_READ(brdcfg[13]);
 	/* Field| Function
 	 * 7-6  | Controls I2C3 routing (net CFG_MUX_I2C3):
 	 * I2C3 | 10= Routes {SCL, SDA} to CAN1 transceiver as {TX, RX}.
 	 * 5-4  | Controls I2C4 routing (net CFG_MUX_I2C4):
 	 * I2C4 |11= Routes {SCL, SDA} to CAN2 transceiver as {TX, RX}.
 	 */
 	reg &= ~(0xf0);
 	reg |= 0xb0;
 	QIXIS_WRITE(brdcfg[13], reg);

 	reg = QIXIS_READ(brdcfg[15]);
 	/* Field| Function
 	 * 7    | Controls the CAN1 transceiver (net CFG_CAN1_STBY):
 	 * CAN1 | 0= CAN #1 transceiver enabled
 	 * 6    | Controls the CAN2 transceiver (net CFG_CAN2_STBY):
 	 * CAN2 | 0= CAN #2 transceiver enabled
 	 */
 	reg &= ~(0xc0);
 	QIXIS_WRITE(brdcfg[15], reg);
 #endif
 #endif

 	return 0;
 }

 #ifdef CONFIG_LPUART
 u32 get_lpuart_clk(void)
 {
 	return gd->bus_clk / CONFIG_SYS_FSL_LPUART_CLK_DIV;
 }
 #endif

 int board_init(void)
 {
 #ifdef CONFIG_FSL_LS_PPA
 	ppa_init();
 #endif

 #ifndef CONFIG_SYS_EARLY_PCI_INIT
 	pci_init();
 #endif

 #if defined(CONFIG_TARGET_LS1028ARDB)
 	u8 val = I2C_MUX_CH_DEFAULT;

 #if !CONFIG_IS_ENABLED(DM_I2C)
 	i2c_write(I2C_MUX_PCA_ADDR_PRI, 0x0b, 1, &val, 1);
 #else
 	struct udevice *dev;

 	if (!i2c_get_chip_for_busnum(0, I2C_MUX_PCA_ADDR_PRI, 1, &dev))
 		dm_i2c_write(dev, 0x0b, &val, 1);
 #endif
 #endif

 #if defined(CONFIG_TARGET_LS1028ARDB)
 	u8 reg;

 	reg = QIXIS_READ(brdcfg[4]);
 	/*
 	 * Field | Function
 	 * 3     | DisplayPort Power Enable (net DP_PWR_EN):
 	 * DPPWR | 0= DP_PWR is enabled.
 	 */
 	reg &= ~(DP_PWD_EN_DEFAULT_MASK);
 	QIXIS_WRITE(brdcfg[4], reg);
 #endif
 	return 0;
 }

 int board_eth_init(struct bd_info *bis)
 {
 	return pci_eth_init(bis);
 }

 #ifdef CONFIG_MISC_INIT_R
 int misc_init_r(void)
 {
 	config_board_mux();

 	return 0;
 }
 #endif

 int board_early_init_f(void)
 {
 #ifdef CONFIG_LPUART
 	u8 uart;
 #endif

 #if defined(CONFIG_SYS_I2C_EARLY_INIT) && defined(CONFIG_SPL_BUILD)
 	i2c_early_init_f();
 #endif

 	fsl_lsch3_early_init_f();

 #ifdef CONFIG_LPUART
 	/*
 	 * Field| Function
 	 * --------------------------------------------------------------
 	 * 7-6  | Controls I2C3 routing (net CFG_MUX_I2C3):
 	 * I2C3 | 11= Routes {SCL, SDA} to LPUART1 header as {SOUT, SIN}.
 	 * --------------------------------------------------------------
 	 * 5-4  | Controls I2C4 routing (net CFG_MUX_I2C4):
 	 * I2C4 |11= Routes {SCL, SDA} to LPUART1 header as {CTS_B, RTS_B}.
 	 */
 	/* use lpuart0 as system console */
 	uart = QIXIS_READ(brdcfg[13]);
 	uart &= ~CFG_LPUART_MUX_MASK;
 	uart |= CFG_LPUART_EN;
 	QIXIS_WRITE(brdcfg[13], uart);
 #endif

 	return 0;
 }

 void detail_board_ddr_info(void)
 {
 	puts("\nDDR    ");
 	print_size(gd->bd->bi_dram[0].size + gd->bd->bi_dram[1].size, "");
 	print_ddr_info(0);
 }

 int esdhc_status_fixup(void *blob, const char *compat)
 {
 	void __iomem *dcfg_ccsr = (void __iomem *)DCFG_BASE;
 	char esdhc1_path[] = "/soc/mmc@2140000";
 	char esdhc2_path[] = "/soc/mmc@2150000";
 	char dspi1_path[] = "/soc/spi@2100000";
 	char dspi2_path[] = "/soc/spi@2110000";
 	u32 mux_sdhc1, mux_sdhc2;
 	u32 io = 0;

 	/*
 	 * The PMUX IO-expander for mux select is used to control
 	 * the muxing of various onboard interfaces.
 	 */

 	io = in_le32(dcfg_ccsr + DCFG_RCWSR12);
 	mux_sdhc1 = (io >> DCFG_RCWSR12_SDHC_SHIFT) & DCFG_RCWSR12_SDHC_MASK;

 	/* Disable esdhc1/dspi1 if not selected. */
 	if (mux_sdhc1 != 0)
 		do_fixup_by_path(blob, esdhc1_path, "status", "disabled",
 				 sizeof("disabled"), 1);
 	if (mux_sdhc1 != 2)
 		do_fixup_by_path(blob, dspi1_path, "status", "disabled",
 				 sizeof("disabled"), 1);

 	io = in_le32(dcfg_ccsr + DCFG_RCWSR13);
 	mux_sdhc2 = (io >> DCFG_RCWSR13_SDHC_SHIFT) & DCFG_RCWSR13_SDHC_MASK;

 	/* Disable esdhc2/dspi2 if not selected. */
 	if (mux_sdhc2 != 0)
 		do_fixup_by_path(blob, esdhc2_path, "status", "disabled",
 				 sizeof("disabled"), 1);
 	if (mux_sdhc2 != 2)
 		do_fixup_by_path(blob, dspi2_path, "status", "disabled",
 				 sizeof("disabled"), 1);

 	return 0;
 }

 #ifdef CONFIG_OF_BOARD_SETUP
 int ft_board_setup(void *blob, struct bd_info *bd)
 {
 	u64 base[CONFIG_NR_DRAM_BANKS];
 	u64 size[CONFIG_NR_DRAM_BANKS];

 	ft_cpu_setup(blob, bd);

 	/* fixup DT for the two GPP DDR banks */
 	base[0] = gd->bd->bi_dram[0].start;
 	size[0] = gd->bd->bi_dram[0].size;
 	base[1] = gd->bd->bi_dram[1].start;
 	size[1] = gd->bd->bi_dram[1].size;

 #ifdef CONFIG_RESV_RAM
 	/* reduce size if reserved memory is within this bank */
 	if (gd->arch.resv_ram >= base[0] &&
 	    gd->arch.resv_ram < base[0] + size[0])
 		size[0] = gd->arch.resv_ram - base[0];
 	else if (gd->arch.resv_ram >= base[1] &&
 		 gd->arch.resv_ram < base[1] + size[1])
 		size[1] = gd->arch.resv_ram - base[1];
 #endif

 	fdt_fixup_memory_banks(blob, base, size, 2);

 	fdt_fixup_icid(blob);

 #ifdef CONFIG_FSL_ENETC
 	fdt_fixup_enetc_mac(blob);
 #endif

 	return 0;
 }
 #endif

 #ifdef CONFIG_FSL_QIXIS
 int checkboard(void)
 {
 #ifdef CONFIG_TFABOOT
 	enum boot_src src = get_boot_src();
 #endif
 	u8 sw;

 	int clock;
 	char *board;
 	char buf[64] = {0};
 	static const char *freq[6] = {"100.00", "125.00", "156.25",
 					"161.13", "322.26", "100.00 SS"};

 	cpu_name(buf);
 	/* find the board details */
 	sw = QIXIS_READ(id);

 	switch (sw) {
 	case 0x46:
 		board = "QDS";
 		break;
 	case 0x47:
 		board = "RDB";
 		break;
 	case 0x49:
 		board = "HSSI";
 		break;
 	default:
 		board = "unknown";
 		break;
 	}

 	sw = QIXIS_READ(arch);
 	printf("Board: %s-%s, Version: %c, boot from ",
 	       buf, board, (sw & 0xf) + 'A' - 1);

 	sw = QIXIS_READ(brdcfg[0]);
 	sw = (sw & QIXIS_LBMAP_MASK) >> QIXIS_LBMAP_SHIFT;

 #ifdef CONFIG_TFABOOT
 	if (src == BOOT_SOURCE_SD_MMC) {
 		puts("SD\n");
 	} else if (src == BOOT_SOURCE_SD_MMC2) {
 		puts("eMMC\n");
 	} else {
 #endif
 #ifdef CONFIG_SD_BOOT
 		puts("SD\n");
 #elif defined(CONFIG_EMMC_BOOT)
 		puts("eMMC\n");
 #else
 		switch (sw) {
 		case 0:
 		case 4:
 			printf("NOR\n");
 			break;
 		case 1:
 			printf("NAND\n");
 			break;
 		default:
 			printf("invalid setting of SW%u\n", QIXIS_LBMAP_SWITCH);
 			break;
 		}
 #endif
 #ifdef CONFIG_TFABOOT
 	}
 #endif

 	printf("FPGA: v%d (%s)\n", QIXIS_READ(scver), board);
 	puts("SERDES1 Reference : ");

 	sw = QIXIS_READ(brdcfg[2]);
 #ifdef CONFIG_TARGET_LS1028ARDB
 	clock = (sw >> 6) & 3;
 #else
 	clock = (sw >> 4) & 0xf;
 #endif

 	printf("Clock1 = %sMHz ", freq[clock]);
 #ifdef CONFIG_TARGET_LS1028ARDB
 	clock = (sw >> 4) & 3;
 #else
 	clock = sw & 0xf;
 #endif
 	printf("Clock2 = %sMHz\n", freq[clock]);

 	return 0;
 }
 #endif
	// SPDX-License-Identifier: GPL-2.0+
	/*
	* Copyright 2019, 2021 NXP
	*/

	#include <common.h>
	#include <init.h>
	#include <malloc.h>
	#include <errno.h>
	#include <fsl_ddr.h>
	#include <net.h>
	#include <asm/global_data.h>
	#include <asm/io.h>
	#include <hwconfig.h>
	#include <fdt_support.h>
	#include <linux/libfdt.h>
	#include <env_internal.h>
	#include <asm/arch-fsl-layerscape/soc.h>
	#include <asm/arch-fsl-layerscape/fsl_icid.h>
	#include <i2c.h>
	#include <asm/arch/soc.h>
	#ifdef CONFIG_FSL_LS_PPA
	#include <asm/arch/ppa.h>
	#endif
	#include <fsl_immap.h>
	#include <netdev.h>

	#include <fdtdec.h>
	#include <miiphy.h>
	#include "../common/qixis.h"
	#include "../drivers/net/fsl_enetc.h"

	DECLARE_GLOBAL_DATA_PTR;

	int config_board_mux(void)
	{
	#ifndef CONFIG_LPUART
	#if defined(CONFIG_TARGET_LS1028AQDS) && defined(CONFIG_FSL_QIXIS)
	u8 reg;

	reg = QIXIS_READ(brdcfg[13]);
	/* Field\| Function
	* 7-6 \| Controls I2C3 routing (net CFG_MUX_I2C3):
	* I2C3 \| 10= Routes {SCL, SDA} to CAN1 transceiver as {TX, RX}.
	* 5-4 \| Controls I2C4 routing (net CFG_MUX_I2C4):
	* I2C4 \|11= Routes {SCL, SDA} to CAN2 transceiver as {TX, RX}.
	*/
	reg &= ~(0xf0);
	reg \|= 0xb0;
	QIXIS_WRITE(brdcfg[13], reg);

	reg = QIXIS_READ(brdcfg[15]);
	/* Field\| Function
	* 7 \| Controls the CAN1 transceiver (net CFG_CAN1_STBY):
	* CAN1 \| 0= CAN #1 transceiver enabled
	* 6 \| Controls the CAN2 transceiver (net CFG_CAN2_STBY):
	* CAN2 \| 0= CAN #2 transceiver enabled
	*/
	reg &= ~(0xc0);
	QIXIS_WRITE(brdcfg[15], reg);
	#endif
	#endif

	return 0;
	}

	#ifdef CONFIG_LPUART
	u32 get_lpuart_clk(void)
	{
	return gd->bus_clk / CONFIG_SYS_FSL_LPUART_CLK_DIV;
	}
	#endif

	int board_init(void)
	{
	#ifdef CONFIG_FSL_LS_PPA
	ppa_init();
	#endif

	#ifndef CONFIG_SYS_EARLY_PCI_INIT
	pci_init();
	#endif

	#if defined(CONFIG_TARGET_LS1028ARDB)
	u8 val = I2C_MUX_CH_DEFAULT;

	#if !CONFIG_IS_ENABLED(DM_I2C)
	i2c_write(I2C_MUX_PCA_ADDR_PRI, 0x0b, 1, &val, 1);
	#else
	struct udevice *dev;

	if (!i2c_get_chip_for_busnum(0, I2C_MUX_PCA_ADDR_PRI, 1, &dev))
	dm_i2c_write(dev, 0x0b, &val, 1);
	#endif
	#endif

	#if defined(CONFIG_TARGET_LS1028ARDB)
	u8 reg;

	reg = QIXIS_READ(brdcfg[4]);
	/*
	* Field \| Function
	* 3 \| DisplayPort Power Enable (net DP_PWR_EN):
	* DPPWR \| 0= DP_PWR is enabled.
	*/
	reg &= ~(DP_PWD_EN_DEFAULT_MASK);
	QIXIS_WRITE(brdcfg[4], reg);
	#endif
	return 0;
	}

	int board_eth_init(struct bd_info *bis)
	{
	return pci_eth_init(bis);
	}

	#ifdef CONFIG_MISC_INIT_R
	int misc_init_r(void)
	{
	config_board_mux();

	return 0;
	}
	#endif

	int board_early_init_f(void)
	{
	#ifdef CONFIG_LPUART
	u8 uart;
	#endif

	#if defined(CONFIG_SYS_I2C_EARLY_INIT) && defined(CONFIG_SPL_BUILD)
	i2c_early_init_f();
	#endif

	fsl_lsch3_early_init_f();

	#ifdef CONFIG_LPUART
	/*
	* Field\| Function
	* --------------------------------------------------------------
	* 7-6 \| Controls I2C3 routing (net CFG_MUX_I2C3):
	* I2C3 \| 11= Routes {SCL, SDA} to LPUART1 header as {SOUT, SIN}.
	* --------------------------------------------------------------
	* 5-4 \| Controls I2C4 routing (net CFG_MUX_I2C4):
	* I2C4 \|11= Routes {SCL, SDA} to LPUART1 header as {CTS_B, RTS_B}.
	*/
	/* use lpuart0 as system console */
	uart = QIXIS_READ(brdcfg[13]);
	uart &= ~CFG_LPUART_MUX_MASK;
	uart \|= CFG_LPUART_EN;
	QIXIS_WRITE(brdcfg[13], uart);
	#endif

	return 0;
	}

	void detail_board_ddr_info(void)
	{
	puts("\nDDR ");
	print_size(gd->bd->bi_dram[0].size + gd->bd->bi_dram[1].size, "");
	print_ddr_info(0);
	}

	int esdhc_status_fixup(void blob, const char compat)
	{
	void __iomem dcfg_ccsr = (void __iomem )DCFG_BASE;
	char esdhc1_path[] = "/soc/mmc@2140000";
	char esdhc2_path[] = "/soc/mmc@2150000";
	char dspi1_path[] = "/soc/spi@2100000";
	char dspi2_path[] = "/soc/spi@2110000";
	u32 mux_sdhc1, mux_sdhc2;
	u32 io = 0;

	/*
	* The PMUX IO-expander for mux select is used to control
	* the muxing of various onboard interfaces.
	*/

	io = in_le32(dcfg_ccsr + DCFG_RCWSR12);
	mux_sdhc1 = (io >> DCFG_RCWSR12_SDHC_SHIFT) & DCFG_RCWSR12_SDHC_MASK;

	/* Disable esdhc1/dspi1 if not selected. */
	if (mux_sdhc1 != 0)
	do_fixup_by_path(blob, esdhc1_path, "status", "disabled",
	sizeof("disabled"), 1);
	if (mux_sdhc1 != 2)
	do_fixup_by_path(blob, dspi1_path, "status", "disabled",
	sizeof("disabled"), 1);

	io = in_le32(dcfg_ccsr + DCFG_RCWSR13);
	mux_sdhc2 = (io >> DCFG_RCWSR13_SDHC_SHIFT) & DCFG_RCWSR13_SDHC_MASK;

	/* Disable esdhc2/dspi2 if not selected. */
	if (mux_sdhc2 != 0)
	do_fixup_by_path(blob, esdhc2_path, "status", "disabled",
	sizeof("disabled"), 1);
	if (mux_sdhc2 != 2)
	do_fixup_by_path(blob, dspi2_path, "status", "disabled",
	sizeof("disabled"), 1);

	return 0;
	}

	#ifdef CONFIG_OF_BOARD_SETUP
	int ft_board_setup(void blob, struct bd_info bd)
	{
	u64 base[CONFIG_NR_DRAM_BANKS];
	u64 size[CONFIG_NR_DRAM_BANKS];

	ft_cpu_setup(blob, bd);

	/* fixup DT for the two GPP DDR banks */
	base[0] = gd->bd->bi_dram[0].start;
	size[0] = gd->bd->bi_dram[0].size;
	base[1] = gd->bd->bi_dram[1].start;
	size[1] = gd->bd->bi_dram[1].size;

	#ifdef CONFIG_RESV_RAM
	/* reduce size if reserved memory is within this bank */
	if (gd->arch.resv_ram >= base[0] &&
	gd->arch.resv_ram < base[0] + size[0])
	size[0] = gd->arch.resv_ram - base[0];
	else if (gd->arch.resv_ram >= base[1] &&
	gd->arch.resv_ram < base[1] + size[1])
	size[1] = gd->arch.resv_ram - base[1];
	#endif

	fdt_fixup_memory_banks(blob, base, size, 2);

	fdt_fixup_icid(blob);

	#ifdef CONFIG_FSL_ENETC
	fdt_fixup_enetc_mac(blob);
	#endif

	return 0;
	}
	#endif

	#ifdef CONFIG_FSL_QIXIS
	int checkboard(void)
	{
	#ifdef CONFIG_TFABOOT
	enum boot_src src = get_boot_src();
	#endif
	u8 sw;

	int clock;
	char *board;
	char buf[64] = {0};
	static const char *freq[6] = {"100.00", "125.00", "156.25",
	"161.13", "322.26", "100.00 SS"};

	cpu_name(buf);
	/* find the board details */
	sw = QIXIS_READ(id);

	switch (sw) {
	case 0x46:
	board = "QDS";
	break;
	case 0x47:
	board = "RDB";
	break;
	case 0x49:
	board = "HSSI";
	break;
	default:
	board = "unknown";
	break;
	}

	sw = QIXIS_READ(arch);
	printf("Board: %s-%s, Version: %c, boot from ",
	buf, board, (sw & 0xf) + 'A' - 1);

	sw = QIXIS_READ(brdcfg[0]);
	sw = (sw & QIXIS_LBMAP_MASK) >> QIXIS_LBMAP_SHIFT;

	#ifdef CONFIG_TFABOOT
	if (src == BOOT_SOURCE_SD_MMC) {
	puts("SD\n");
	} else if (src == BOOT_SOURCE_SD_MMC2) {
	puts("eMMC\n");
	} else {
	#endif
	#ifdef CONFIG_SD_BOOT
	puts("SD\n");
	#elif defined(CONFIG_EMMC_BOOT)
	puts("eMMC\n");
	#else
	switch (sw) {
	case 0:
	case 4:
	printf("NOR\n");
	break;
	case 1:
	printf("NAND\n");
	break;
	default:
	printf("invalid setting of SW%u\n", QIXIS_LBMAP_SWITCH);
	break;
	}
	#endif
	#ifdef CONFIG_TFABOOT
	}
	#endif

	printf("FPGA: v%d (%s)\n", QIXIS_READ(scver), board);
	puts("SERDES1 Reference : ");

	sw = QIXIS_READ(brdcfg[2]);
	#ifdef CONFIG_TARGET_LS1028ARDB
	clock = (sw >> 6) & 3;
	#else
	clock = (sw >> 4) & 0xf;
	#endif

	printf("Clock1 = %sMHz ", freq[clock]);
	#ifdef CONFIG_TARGET_LS1028ARDB
	clock = (sw >> 4) & 3;
	#else
	clock = sw & 0xf;
	#endif
	printf("Clock2 = %sMHz\n", freq[clock]);

	return 0;
	}
	#endif