| // SPDX-License-Identifier: GPL-2.0 |
| /* |
| * board/renesas/rcar-common/common.c |
| * |
| * Copyright (C) 2013 Renesas Electronics Corporation |
| * Copyright (C) 2013 Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> |
| * Copyright (C) 2015 Nobuhiro Iwamatsu <iwamatsu@nigauri.org> |
| */ |
| |
| #include <common.h> |
| #include <dm.h> |
| #include <init.h> |
| #include <asm/global_data.h> |
| #include <dm/uclass-internal.h> |
| #include <asm/arch/rmobile.h> |
| #include <linux/libfdt.h> |
| |
| #ifdef CONFIG_RCAR_GEN3 |
| |
| DECLARE_GLOBAL_DATA_PTR; |
| |
| /* If the firmware passed a device tree use it for U-Boot DRAM setup. */ |
| extern u64 rcar_atf_boot_args[]; |
| |
| int fdtdec_board_setup(const void *fdt_blob) |
| { |
| void *atf_fdt_blob = (void *)(rcar_atf_boot_args[1]); |
| |
| if (fdt_magic(atf_fdt_blob) == FDT_MAGIC) |
| fdt_overlay_apply_node((void *)fdt_blob, 0, atf_fdt_blob, 0); |
| |
| return 0; |
| } |
| |
| int dram_init(void) |
| { |
| return fdtdec_setup_mem_size_base(); |
| } |
| |
| int dram_init_banksize(void) |
| { |
| fdtdec_setup_memory_banksize(); |
| |
| return 0; |
| } |
| |
| #if defined(CONFIG_OF_BOARD_SETUP) |
| static int is_mem_overlap(void *blob, int first_mem_node, int curr_mem_node) |
| { |
| struct fdt_resource first_mem_res, curr_mem_res; |
| int curr_mem_reg, first_mem_reg = 0; |
| int ret; |
| |
| for (;;) { |
| ret = fdt_get_resource(blob, first_mem_node, "reg", |
| first_mem_reg++, &first_mem_res); |
| if (ret) /* No more entries, no overlap found */ |
| return 0; |
| |
| curr_mem_reg = 0; |
| for (;;) { |
| ret = fdt_get_resource(blob, curr_mem_node, "reg", |
| curr_mem_reg++, &curr_mem_res); |
| if (ret) /* No more entries, check next tuple */ |
| break; |
| |
| if (curr_mem_res.end < first_mem_res.start) |
| continue; |
| |
| if (curr_mem_res.start >= first_mem_res.end) |
| continue; |
| |
| printf("Overlap found: 0x%llx..0x%llx / 0x%llx..0x%llx\n", |
| first_mem_res.start, first_mem_res.end, |
| curr_mem_res.start, curr_mem_res.end); |
| |
| return 1; |
| } |
| } |
| |
| return 0; |
| } |
| |
| int ft_board_setup(void *blob, struct bd_info *bd) |
| { |
| /* |
| * Scrub duplicate /memory@* node entries here. Some R-Car DTs might |
| * contain multiple /memory@* nodes, however fdt_fixup_memory_banks() |
| * either generates single /memory node or updates the first /memory |
| * node. Any remaining memory nodes are thus potential duplicates. |
| * |
| * However, it is not possible to delete all the memory nodes right |
| * away, since some of those might not be DRAM memory nodes, but some |
| * sort of other memory. Thus, delete only the memory nodes which are |
| * in the R-Car3 DBSC ranges. |
| */ |
| int mem = 0, first_mem_node = 0; |
| |
| for (;;) { |
| mem = fdt_node_offset_by_prop_value(blob, mem, |
| "device_type", "memory", 7); |
| if (mem < 0) |
| break; |
| if (!fdtdec_get_is_enabled(blob, mem)) |
| continue; |
| |
| /* First memory node, patched by U-Boot */ |
| if (!first_mem_node) { |
| first_mem_node = mem; |
| continue; |
| } |
| |
| /* Check the remaining nodes and delete duplicates */ |
| if (!is_mem_overlap(blob, first_mem_node, mem)) |
| continue; |
| |
| /* Delete duplicate node, start again */ |
| fdt_del_node(blob, mem); |
| first_mem_node = 0; |
| mem = 0; |
| } |
| |
| return 0; |
| } |
| #endif |
| #endif |