| // SPDX-License-Identifier: GPL-2.0+ |
| /* |
| * (C) Copyright 2007 |
| * Sascha Hauer, Pengutronix |
| * |
| * (C) Copyright 2009 Freescale Semiconductor, Inc. |
| */ |
| |
| #include <common.h> |
| #include <cpu_func.h> |
| #include <asm/arch/imx-regs.h> |
| #include <asm/arch/clock.h> |
| #include <asm/arch/sys_proto.h> |
| #include <asm/cache.h> |
| |
| #include <linux/errno.h> |
| #include <asm/io.h> |
| #include <asm/mach-imx/boot_mode.h> |
| |
| #if !(defined(CONFIG_MX51) || defined(CONFIG_MX53)) |
| #error "CPU_TYPE not defined" |
| #endif |
| |
| u32 get_cpu_rev(void) |
| { |
| #ifdef CONFIG_MX51 |
| int system_rev = 0x51000; |
| #else |
| int system_rev = 0x53000; |
| #endif |
| int reg = __raw_readl(ROM_SI_REV); |
| |
| #if defined(CONFIG_MX51) |
| switch (reg) { |
| case 0x02: |
| system_rev |= CHIP_REV_1_1; |
| break; |
| case 0x10: |
| if ((__raw_readl(GPIO1_BASE_ADDR + 0x0) & (0x1 << 22)) == 0) |
| system_rev |= CHIP_REV_2_5; |
| else |
| system_rev |= CHIP_REV_2_0; |
| break; |
| case 0x20: |
| system_rev |= CHIP_REV_3_0; |
| break; |
| default: |
| system_rev |= CHIP_REV_1_0; |
| break; |
| } |
| #else |
| if (reg < 0x20) |
| system_rev |= CHIP_REV_1_0; |
| else |
| system_rev |= reg; |
| #endif |
| return system_rev; |
| } |
| |
| #ifdef CONFIG_REVISION_TAG |
| u32 __weak get_board_rev(void) |
| { |
| return get_cpu_rev(); |
| } |
| #endif |
| |
| #if !CONFIG_IS_ENABLED(SYS_DCACHE_OFF) |
| void enable_caches(void) |
| { |
| /* Enable D-cache. I-cache is already enabled in start.S */ |
| dcache_enable(); |
| } |
| #endif |
| |
| #if defined(CONFIG_FEC_MXC) |
| void imx_get_mac_from_fuse(int dev_id, unsigned char *mac) |
| { |
| int i; |
| struct iim_regs *iim = (struct iim_regs *)IMX_IIM_BASE; |
| struct fuse_bank *bank = &iim->bank[1]; |
| struct fuse_bank1_regs *fuse = |
| (struct fuse_bank1_regs *)bank->fuse_regs; |
| |
| for (i = 0; i < 6; i++) |
| mac[i] = readl(&fuse->mac_addr[i]) & 0xff; |
| } |
| #endif |
| |
| #ifdef CONFIG_MX53 |
| void boot_mode_apply(unsigned cfg_val) |
| { |
| writel(cfg_val, &((struct srtc_regs *)SRTC_BASE_ADDR)->lpgr); |
| } |
| /* |
| * cfg_val will be used for |
| * Boot_cfg3[7:0]:Boot_cfg2[7:0]:Boot_cfg1[7:0] |
| * |
| * If bit 28 of LPGR is set upon watchdog reset, |
| * bits[25:0] of LPGR will move to SBMR. |
| */ |
| const struct boot_mode soc_boot_modes[] = { |
| {"normal", MAKE_CFGVAL(0x00, 0x00, 0x00, 0x00)}, |
| /* usb or serial download */ |
| {"usb", MAKE_CFGVAL(0x00, 0x00, 0x00, 0x13)}, |
| {"sata", MAKE_CFGVAL(0x28, 0x00, 0x00, 0x12)}, |
| {"escpi1:0", MAKE_CFGVAL(0x38, 0x20, 0x00, 0x12)}, |
| {"escpi1:1", MAKE_CFGVAL(0x38, 0x20, 0x04, 0x12)}, |
| {"escpi1:2", MAKE_CFGVAL(0x38, 0x20, 0x08, 0x12)}, |
| {"escpi1:3", MAKE_CFGVAL(0x38, 0x20, 0x0c, 0x12)}, |
| /* 4 bit bus width */ |
| {"esdhc1", MAKE_CFGVAL(0x40, 0x20, 0x00, 0x12)}, |
| {"esdhc2", MAKE_CFGVAL(0x40, 0x20, 0x08, 0x12)}, |
| {"esdhc3", MAKE_CFGVAL(0x40, 0x20, 0x10, 0x12)}, |
| {"esdhc4", MAKE_CFGVAL(0x40, 0x20, 0x18, 0x12)}, |
| {NULL, 0}, |
| }; |
| #endif |